Achieving a high-strength dissimilar joint of T91 heat-resistant steel to 316L stainless steel via friction stir welding

The reliable welding of T91 heat-resistant steel to 316L stainless steel is a considerable issue for ensuring the safety in service of ultrasupercritical power generation unit and nuclear fusion reactor,but the high-quality dissimilar joint of these two steels was difficult to be obtained by traditional fusion welding methods.Here we improved the structure-property synergy in a dissimilar joint of T91 steel to 316L steel via friction stir welding.A defect-free joint with a large bonding interface was produced using a small-sized tool under a relatively high welding speed.The bonding interface was involved in a mixing zone with both mechanical mixing and metallurgical bonding.No obvious material softening was detected in the joint except a negligible hardness decline of only HV~10 in the heat-affected zone of the T91 steel side due to the formation of ferrite phase.The welded joint exhibited an excellent ultimate tensile strength as high as that of the 316L parent metal and a greatly enhanced yield strength on account of the dependable bonding and material renovation in the weld zone.This work recommends a promising technique for producing high-strength weldments of dissimilar nuclear steels.

Numerical Simulation Analysis of Welded Joints in Arch Ribs of Large Span Steel Pipe Arch Bridges

In order to study the residual stress distribution law of welded joints of arch ribs of large-span steel pipe concrete arch bridges,numerical simulation of temperature,stress and strain fields based on ABAQUS for welded joints of arch-ribbed steel tubes using 7-,8-and 9-layer welds is carried out and its accuracy is demonstrated.The steel pipe welding temperature changes,residual stress distribution,different processes residual stress changes in the law,the prediction of post-weld residual stress distribution and deformation are studied in this paper.The results show that the temperature field values and test results are more consistent with the accuracy of numerical simulation of welding,the welding process is mainly in the form of heat transfer;Residual high stresses are predominantly distributed in the Fusion zone(FZ)and Heat-affected zone(HAZ),with residual stress levels tending to decrease from the center of the weld along the axial path,the maximum stress appears in the FZ and HAZ junction;The number of welding layers has an effect on the residual stress distribution,the number of welding layers increases,the residual stress tends to decrease,while the FZ and HAZ high stress area range shrinks;Increasing the number of plies will increase the amount of residual distortion.

Research and development of 3PP coating steel pipes

The industrial application of an exterior three-layer anticorrosive polypropylene coating system(3PP)on large-diameter(larger than Φ600 mm)steel pipes was developed using an experimental process simulation study and the optimization of raw materials inspection,steel pipe surface pretreatments,and water cooling control on a coating application process.The coating properties meet ISO standard 21809 on buried or submerged 3PP pipelines used in the petroleum and natural gas industries.Differential scanning calorimetry and X-ray diffraction were used to analyze the crystallinities and grain sizes of polypropylene(PP)top coats with different cooling rates.Increasing the melt cooling rate reduces the crystallinity and grain size of the PP top coat and enhances its strength and toughness.

Influence of Creep Strength of Weld on Interfacial Creep Damage of Dissimilar Welded Joint between Martensitic and Bainitic Heat-Resistant Steel

The mechanical properties, creep rupture strength, creep damage and failure characteristics of dissimilar metal welded joint （DMWJ） between martensitic （SA213T91） and bainitic heat-resistant steel （12Cr2MoWVTiB（G102）） have been investigated by means of pulsed argon arc welding, high temperature accelerated simulation, mechanical and creep rupture test, and scanning electronic microscope （SEM）. The results show that there is a marked drop of mechanical properties of undermatching joint, and low ductility cracking along weld/G102 interface is induced due to creep damage. Creep rupture strength of overmatching joint is the least. The mechanical properties of medium matching joint are superior to those of overmatching and undermatching joint, and creep damage and failure tendency along the interface of weld/G102 are lower than those of overmatching and undermatching joint after accelerated simulation for 500 h, 1 000 h, 1 500 h, and the creep rupture strength of medium matching joint is the same as that of undermatching joint. Therefore, it is reasonable that the medium matching material is used for dissimilar welded joint between martensitic and bainitic steel.

Dissolution Behavior of Delta Ferrites in Martensitic Heat-resistant Steel for Ultra Supercritical Units Blades

The dissolution behavior of delta ferrites in martensitic heat-resistant steel was studied.And the reason why the dissolution rate of delta ferrites decreased with dissolution time was discussed.The experimental results show that the chemical compositions of delta ferrites negligibly change with dissolution time.The decrease of dissolution rate of delta ferrites with dissolution time should be attributed to the change of shape and distribution of delta ferrites.The shape of delta ferrites tends to transfer from polygon to sphere with dissolution time,causing the decrease of specific surface area of delta ferrites.The distribution position of delta ferrites tends to transfer from boundaries of austenite grains to interior of austenite grains with dissolution time,decreasing the diffusion coefficient of alloy atoms.Both them decrease the dissolution rate of delta ferrites.

High-temperature oxidation behavior of 9Cr‒5Si‒3Al ferritic heat-resistant steel

To improve the oxidation properties of ferritic heat-resistant steels,an Al-bearing 9Cr‒5Si‒3Al ferritic heat-resistant steel was designed.We then conducted cyclic oxidation tests to investigate the high-temperature oxidation behavior of 9Cr‒5Si and 9Cr‒5Si‒3Al ferritic heat-resistant steels at 900 and 1000℃.The characteristics of the oxide layer were analyzed by X-ray diffraction,scanning electron microscopy,and energy dispersive spectroscopy.The results show that the oxidation kinetics curves of the two tested steels follow the parabolic law,with the parabolic rate constant kp of 9Cr‒5Si‒3Al steel being much lower than that of 9Cr‒5Si steel at both 900 and 1000℃.The oxide film on the surface of the 9Cr‒5Si alloy exhibits Cr2MnO4 and Cr2O3 phases in the outer layer after oxidation at 900 and 1000℃.However,at oxidation temperatures of 900 and 1000℃,the oxide film of the 9Cr‒5Si‒3Al alloy consists only of Al2O3 and its oxide layer is thinner than that of the 9Cr‒5Si alloy.These results indicate that the addition of Al to the 9Cr‒5Si steel can improve its high-temperature oxidation resistance,which can be attributed to the formation of a continuous and compact Al2O3 film on the surface of the steel.

Microstructure and Corrosion Resistance of CrN and CrN/TiN Coated Heat-Resistant Steels in Molten Aluminum Alloy

The components of the equipment for processing the Al melts into the molded parts can be markedly corroded by the molten Al. In this study, a 4 μm CrN coating or CrN/TiN multilayer coating for providing the physical and chemical barriers between the molten reactive Al and the steel substrate were deposited by Cathodic Arc Evaporation onto 10 mm-thick heat-resistant steel plates. The dipping tests were conducted in a 700℃ A356 melt for 1 to 21 h at intervals of 3 h. The damage of the coated steel was eva...

EFFECT OF W ON MECHANICAL PROPERTIES OF 12%Cr HEAT-RESISTANT STEEL

The effect of W on mechanical properties of 12% Cr-W-V-Nb heat resistant steel at high temperatures and room temperature is reported.The experimental results indicated that if the W content was about 2.2—3.0 wt-%,there was no obviously change of R.T.tensile strength, but impact toughness decreased with the rise of W content.On the other hand,the increase of W content enhanced the short time stress rupture strength,but did not for the long time one. The increase of W have two effects on the precipitation behavior,promoting Laves formation of type Fe_2W,increasing the precipitated phase amount and speeding up the coarsening pro- cess of precipitated phase at high temperatures.The effect of W on the mechanical properties is closely associated with precipitation behaviors.When the rupture life is short,there has no enough time to coarsen the precipitated phases,so the increase of precipitated phases results in strengthening effect,i.e.the W increases the high temperature strength.After prolonged expo- sure,the evident coarsening took plaee,that decreased the effect of precipitation.

Development and Application of a Heat-resistant Low Ni Steel Modified by Rare Earth for Furnace Roller

The low Ni steel modified hy rare earth(3Cr24NiTSiN with an addition of 0.3% Ce)for furnace roller has been developed.Due to the RE(rare earth)addition,a dense oxide film is formed on the steel surface at high temperature,and the oxidation rate is decreased.This film has so good adhesion to the matrix that it will not be peeled off easily.The RE modified steel has excellent oxidation resistance and thermal strength even if being used continuously for a long period at high temperature.This steel roller has a service life of about 4 years com- parable to high Ni steel ones,so the low Ni steel can replace high Ni steel to make furnace roller.The Ni content of this material can be reduced by 65% in comparison with Cr25Ni20Si2 steel,The low Ni steel has better pro- eessing properties including melting,casting and working properties than that of high Ni ones.

Investigation on the strengthening mechanism of S30432 austenitic heat-resistant steel

From the viewpoint of energy-saving and environment protection,it is necessary to develop Ultra Super Critical(USC) fossil-fired power plants.In order to ensure the reliable operation of power plants under high steam conditions,good mechanical properties(particularly high creep strength),corrosion resistance and fabricability are generally required for the heat resistant steels used in USC boilers.Among these heat-resistant steels,S30432 austenitic heat-resistant steels are of interest due to high creep strength,excellent oxidation and corrosion resistance at temperatures up to 650 -700℃.In this paper,the strengthening mechanism of S30432 austenitic heat-resistant steel was investigated based on the precipitation behavior of S30432 during aging and creep at 650℃.Results show that the microstructure of as-supplied S30432 steel is austenite,the main precipitation consists of only Nb(C,N).After aged for 10 000 h or crept for 10 712 h,there is a slight increase in the size of fine Nb(C,N),but the transformation from Nb(C,N) to NbCrN does not occur.Aging and creep results in the precipitation ofε-Cu and M_(23)C_6.The coarsening velocity ofε-Cu particles diminishes greatly and they are still very fine in the long-term creep range.With the increase of aging and creep time M_(23)C_6 carbides tend to coarsen gradually.The size of M_(23)C_6 is larger and the coarsening is easier in contrast toε-Cu and Nb(C,N).Nb(C,N) precipitates in the as-supplied microstructure,while aging and creep result in the precipitation ofε-Cu and M_(23)C_6.High creep rupture strength of S30432 steel is attributed to the precipitation hardening ofε-Cu,Nb(C,N) and M_(23)C_6.Extremely,ε-Cu plays an important role in improving the creep rupture strength of S30432,and at least 61%of the creep rupture strength of S30432 at 650℃results from the precipitation hardening ofε-Cu particles.

Deformation behavior of 9Cr-3W-3Co martensitic heat-resistant steel

The deformation behavior of 9 Cr-3 W-3 Co heat-resistant steel at a high-temperature range of 1 060-1 260 ℃ and a strain rate of 0.3 s^(-1) was studied using a Gleeble 3800 heat-simulating test machine. The microstructure and precipitation phases of the steel at different temperatures were studied by optical microscopy,scanning electron microscopy,and transmission electron microscopy. The results show that due to its low melting point,coarse grain size,and the segregation of P,S,and Cu at the grain boundary,the thermoplasticity of 9 Cr-3 W-3 Co steel is poor at temperatures higher than 1 200 ℃.The bulk ferrite phase was the main factor affecting the thermoplasticity at 1 100-1 200 ℃.

Effect of microstructure on the low temperature toughness of high strength pipeline steels

Microstructure observations and drop-weight tear test were performed to study the microstructures and mechanical properties of two kinds of industrial X70 and two kinds of industrial X80 grade pipeline steels. The effective grain size and the fraction of high angle grain boundaries in the pipeline steels were investigated by electron backscatter diffraction analysis. It is found that the low temperature toughness of the pipeline steels depends not only on the effective grain size, but also on other microstructural factors such as martensite-austenite （MA） constituents and precipitates. The morphology and size of MA constituents significantly affect the mechanical properties of the pipeline steels. Nubby MA constituents with large size have significant negative effects on the toughness, while smaller granular MA constituents have less harmful effects. Similarly, larger Ti-rich nitrides with sharp corners have a strongly negative effect on the toughness, while fine, spherical Nb-rich carbides have a less deleterious effect. The low temperature toughness of the steels is independent of the fraction of high angle grain boundaries.

Theoretical and experimental study of the thermal strength of anticorrosive lined steel pipes

Bimetallic lined steel pipe （LSP） is a new anti-corrosion technology. It is widely used to transport oil, gas, water and corrosive liquid chemicals. At present, the hydroforming pressure for LSP has been investigated theoretically and experimentally by most researchers. However, there are a few reports on the thermal strength of bimetallic LSP. Actually, the bimetallic LSP will be subjected to remarkable thermal load in the process of three layer polyethylene （3PE） external coating. Reverse yielding failure may occur on the inner pipe of the bimetallic LSP when it suffers from remarkable thermal load and residual contact pressure simultaneously. The aim of this paper is to study the thermal load and strength of the bimetallic LSP. A mechanical model, which can estimate the thermal strength of the bimetallic LSP, was established based on the elastic theory and the manufacture of the bimetallic LSP. Based on the model, the correlation between the thermal strength of the bimetallic LSP and residual contact pressure and wall thickness of the inner pipe was obtained. Reverse yielding experiments were performed on the LSP （NT80SS-316L） under different thermal loads. Experiment results are consistent with calculated results from the theoretical model. The experimental and simulation results may provide powerful guidance for the bimetallic LSP production and use.

Effect of Sacrificial Anode Protection for Steel Pipe Piles at Dandong Port

The sacrificial anode protection system for the steel pipe piles of the 3rd berth of Dandong; wharf at Dandong port has operated for eight years. In this paper, the program design and the protection effect of the sacrificial anode protection system are presented. The results of various inspections show that the piles are protected very satisfactorily.

Numerical study on forming complex fitting body on end of integrated stainless steel pipe without welds

It is necessary to use the integrated stainless steel pipe having two fitting bodies without welds while train travelling at high speed. In order to form this type of integrated stainless steel pipe, the method of preforming combined finish forming process is developed. The preforming process is characterized by flaring combined upsetting for left fitting body which is like a flange, and is characterized by tube axial compressive process under die constraint for right fitting body which is like a double-wall pipe. The finite element simulations of the processes are carried out by software package DEFORM, and the results indicate that: 1) left or right fitting body can be formed by a two-step forming process without folding and under-filling defects; 2) by using two-step forming, strain and stress in left fitting body are larger than those in right fitting body, and deformation in right fitting body is more homogenous than the deformation in left fitting body; 3) two or more preforming steps may be needed for left fitting body considering the distributions of strain and stress.

Development of pipeline steel at Baosteel over the last 20 years

This study reviews the development of Baosteel＇ s pipeline steel over the last 20 years. Energy demand accelerates the development of high-grade pipeline steel as well as modem petroleum and natural gas pipeline construction. Pipeline steel is a kind of typical modem microalloyed steel produced via thermo-mechanical controlled processing. The development process of pipeline steel at Baosteel represents the course of the technological progress of pipeline steel in China. In the last two decades, Baosteel＇ s pipeline steel has been developed from a single product of hot- rolled strips to a variety of products including hot-rolled strips, heavy plates, high-frequency electric resistance welded （HFW） pipes and U-ing-O-ing-Expanding （UOE） welded pipes. Moreover, the proportion of the HFW and the UOE welded pipes has been increasing year by year. UOE longitudinal submerged arc welding （SAW） pipes have become the leading product of strategic significance in Baosteel＇ s pipeline steel family. Over the last 20 years, Baosteel＇ s pipeline steel products have shifted from ＂ferrite ＋ pearlite＂ X52 to ＂acicular ferrite＂ XT0 and X80, and Baosteel has developed hydrogen-induced cracking （HIC） resistant pipeline steel. Baosteel＇ s pipeline steel products have been applied in variety of geographical areas,including deserts, Gobi, mountains,plains as well as the ocean. And both the X100 and the X120 ultra high strength pipeline steels have been produced on a trial basis. Baosteel has accumulatively produced 6.5 Mt of pipeline steel for both domestic and overseas projects. Baosteel will continue strengthening its strategic cooperation with oil companies, and conducting research on ultra high strength pipeline steel, pipeline steel for strain-based design and submarine pipeline steel,etc. , so as to meet the need of construction in the future.

Finite Element Analysis of the Steel Reinforced Plastic Pipe

The steel reinforced plastic pipe is a kind of green environmental protection pipelines with double-sides corrosionresisting and better withstanding to medium working pressure. The structure and technical process of this pipe are described briefly in this paper, and the finite element analysis has been done for the sake of understanding the distributions of stress and displacement inside this pipe under hydrostatic pressure. The analysis results are very important for safety application of the steel reinforced plastic pipe.

Effect of Pipe Diameter on Electrochemical Behavior of Stainless Steel Type 304 Pipes in Tap Water

We investigated the effects of pipe diameter on the corrosion resistance of stainless steel type 304 pipes using electrochemical measurements. Compared to plate steel, pipes have harder physical properties and tend to be harder and showed greater permeability with decreasing inner diameter. We found that the maximum corrosion current density in the secondary active state, which is the starting point of secondary passivation, appeared in the polarization curve measurement in tap water. Similar to the Vickers hardness and the maximum current density in the secondary active state, the permeability tended to increase as the diameter decreased. This is thought to increase the amount of deformation-induced martensitic and increase corrosion susceptibility. The peak of the secondary active current density was clearly seen as the potential sweep speed was increased. In addition, potential sweep speed dependence was observed in the corrosion susceptibility evaluation of deformation-induced martensite. In comparison with acid treatment, the formation of deformation-induced martensite was considered to occur in the extreme surface layer. The maximum corrosion current density in the secondary active state is expected to be a new susceptibility evaluation method for evaluating the deformation-induced martensitic transformation.

A Dynamics Study of a Magnetic Flux Leakage(MFL) Signal and its Application to Defect Location Discrimination in Steel Pipes MFL Testing Equipment

Difference processing was used to the direct current magnetic flux leakage （DC-MFL） signal, emanating from the defects machined artificially on the internal and external surfaces of a steel pipe. Consequently, the loea-tion discriminating index 8 was provided to identify the defect whether it is on the internal surface or the external one. Three characteristics, shape, depth and orientation of the defect, were discussed through a series of experiments on the artificial defects, such as transverse notches, oblique notches and pits on the steel pipe. The approach has been verified effective to address the defect location identifying problem, albeit the limits on the accuracy assessment to those natural defects on steel pipes in service.

The Vibration Controllability of 20~# Steel Pipe Excited by Unsteady Flow

An excited experiment system of 20# steel pipe was established with oil cylinder, 20# steel pipe, frequency converter, pump station and wave exciter generating unsteady flow artificially. The experimental results showed that the 20# steel pipe could vibrate with the excitation of unsteady flows, and the vibration was periodic, instead of a harmonic one. Particles on the front and rear positions of pipe vibrated synchronously, and the vibration intensity of the pipe＇s two ends was greater than in the middle. System pressure and wave exciter＇s frequency had much influence upon pipe＇s amplitude. Pipe＇s vibration frequency was little affected by system pressure, and its value was close to the wave exciter＇s. Therefore, the active control of pipe＇s vibration can be realized by setting system pressure and adjusting frequency converter＇s frequency.