Relationship among solution heating rate,mechanical properties,microstructure and texture of Al−Mg−Si−Cu alloy

The relationship among heating rate, mechanical properties, microstructure and texture of Al-Mg-Si-Cu alloy during solution treatment was investigated through tensile test, scanning electron microscope, X-ray diffractometer and EBSD technology. The experimental results reveal that there is a non-monotonic relationship among solution heating rate, mechanical properties, microstructure and texture. As the solution heating rate increases, the strength variations are dependent on the tensile direction;work hardening exponent n decreases first, and then increases;plastic strain ratio r increases first, and then decreases, and finally increases. The final microstructure and texture are also affected by heating rate. As heating rate increases, the microstructure transforms from elongated grain structure to equiaxed grain structure, and the average grain size decreases first, and then increases, and decreases finally. Although the texture components including CubeND{001}<310> and P{011}<122> orientations almost have no change with the increase of heating rate, the texture intensity and volume fraction decrease first, and then increase, and finally decrease. Both microstructure and texture evolutions are weakly affected by heating rate. Improving heating rate is not always favorable for the development of fine equiaxed grain structure, weak texture and high average r value, which may be related to the recrystallization behavior.

Effect of heating rate on the densification of NdFeB alloys sintered by an electric field

This study introduces a novel method of electric field sintering for preparing NdFeB magnets. NdFeB alloy compacts were all sintered by electric fields for 8 min at 1000~C with different preset heating rates. The characteristics of electric field sintering and the effects of heating rate on the sintering densification of NdFeB alloys were also studied. It is found that electric field sintering is a new non-pressure rapid sintering method for preparing NdFeB magnets with fine grains at a relatively lower sintering temperature and in a shorter sintering time. Using this method, the sintering temperature and process of the compacts can be controlled accurately. When the preset heating rate in- creasing from 5 to 2000~C/s the densification of NdFeB sintered compacts gradHally improves. As the preset heating rate is 2000C/s, Nd-rich phases are small, dispersed and uniformly distributed in the sintered compact, and the magnet has a better microstructure than that made by conventional vacuum sintering. Also, the maximum energy product of the sintered magnet reaches 95% of conventionally vacuum sintered magnets.

Effect of Heating Rates on the Formable Oxide Scale on a C-Steel Surface

Oxide scale formation on a C-steel surface has been investigated using linear heating rates ranging from 0.1℃/min to 10℃/min at high temperatures. The studies on the oxide scale formation at high temperature (650℃) at slower heating rate (0.1℃/min) shows that the kinetic regime is linear. X-ray diffraction measurements revealed that the scale constituents are significantly influenced by the heating rate. The adherence of the scale was improved by using slower heating rate (0.1℃/min-≤650℃), while above such degree the scale was susceptible to cracking and flaking out of the alloy surface. In fact, the development of oxide growth stresses can cause considerable scale cracking. As well, variation of the crystallite sizes under the aforementioned conditions might affect the scale stacking to the alloy surface. The secondary electron detector images of the oxide scale shows that the scale was imperfectly smooth and there were a number of voids and defects in the scale skin, especially at fast heating rate. This observation could be attributed to defects of the as-received alloy. In general, slower heating rate reduced the defects of the scale and improved its adherence.

Effect of temperature and heating rate on mechanical properties of magnesium alloy AZ31

Effects of temperature and heating rate on the mechanical properties of the tensile specimens of magnesium alloy AZ31 were experimentally investigated using a Gleeble-1500 thermo-mechanical material testing system.The metallurgraphs of the fracture section of the specimens were also experimentally observed and analyzed for exploring their failure mechanism under different temperatures and heating rates.The results show that the higher the temperature,the lower the ultimate strength of the specimens.And the higher the heating rate,the higher the ultimate strength of the specimens.The high temperatures and high heating rates will induce microvoids in the specimens which make the specimens failure under relatively low loads.

Influence of Heating Rate on Double Reversible Transformation in CuZnAlMnNi Shape Memory Alloy

The influence of heating rate on double reversible transformation in CuZnAlMnNi shape memory alloy was investigated by differential scanning calorimetry. It was found that rapid heating inhibits X -->M transformation but is favorable to the reverse martensite transformation, giving rise to the approach of the two transformation peaks. With the decrease of heating rate, the two transformation peaks separate gradually.

Spatial Distributions of Atmospheric Radiative Fluxes and Heating Rates over China during Summer

The latitude-altitude distributions of radiative fluxes and heating rates are investigated by utilizing CloudSat satellite data over China during summer. The Tibetan Plateau causes the downward shortwave fluxes of the lower atmosphere over central China to be smaller than the fluxes over southern and northern China by generating more clouds. The existence of a larger quantity of clouds over central China reflects a greater amount of solar radiation back into space. The vertical gradients of upward shortwave radiative fluxes in the atmosphere below 8 km are greater than those above 8 km. The latitudinal-altitude distributions of downward longwave radiative fluxes show a slantwise decreasing trend from low latitudes to high latitudes that gradually weaken in the downward direction. The upward longwave radiative fluxes also weaken in the upward direction but with larger gradients. The maximum heating rates by solar radiation and cooling rates by longwave infrared radiation are located over 28 40°N at 7 8 km mean sea level (MSL), and they are larger than the rates in the northern and southern regions. The heating and cooling rates match well both vertically and geographically.

Effects of Heating Rate on the Process Parameters of Superplastic Forming for Zr_(55)Cu_(30)Al_(10)Ni_5

We investigated the effects of heating rate on the process parameters of superplastic forming for Zr55Cu30Al10Ni5 by differential scanning calorimetry. The continuous heating and isothermal annealing analyses suggested that the temperatures of glass transition and onset crystallization are heating rate-dependent in the supercooled liquid region. Then, the time-temperature-transformation diagram under different heating rates indicates that increasing the heating rate can lead to an increase of the incubation time at the same anneal temperature in the supercooled liquid region. Based on the Arrhenius relationship, we discovered that the incubation time increases by 1.08-1.11 times with double increase of the heating rate at the same anneal temperature, and then verified it by the data of literatures and the experimental results. The obtained curve of the max available incubation time reveals that the incubation time at a certain anneal temperature in the supercooled liquid region is not infinite, and will increase with increasing heating rate until this temperature shifts out of the supercooled liquid region because of exceeding critical heating rate. It is concluded that heating rate must be an important processing parameter of superplastic forming for Zr55Cu30Al10Ni5.

EFFECT OF HEATING RATE ON THERMO-INDUCED AGGREGATION OF POLY(ETHYLENE OXIDE)-b-POLY(N-ISOPROPYLACRYLAMIDE) IN AQUEOUS SOLUTIONS

The effects of heating rate on the aggregate behavior of poly（ethylene oxide）-b-poly（N-isopropylacrylamide） in aqueous solutions were investigated in detail by laser light scattering and TEM. By employing two separate heating protocols, step-by-step heating at 〈 5 K/step and one-step jump, to heat the sample from 15℃ to the selected temperature, we found that the heating rate only showed significant effect on the aggregates above the cloud point. The aggregate formed by step-by-step heating exhibited a much larger size and a broader size distribution than those formed by one-step jump heating. Moreover, neither of the aggregates were ideal micellar structures as indicated by the size and the Rg/Rh values. On the contrary, at temperatures below the cloud point where the block copolymer formed core-shelled micelles, the heating rate showed negligible effect on the size and size distribution of the micelles. Since the system underwent a phase separation above the cloud point, the heating rate effect could be reasonably explained by the phase separation mechanisms： the nucleation-and-growth mechanism in the metastable region and the spinodal decomposition mechanism in the unstable region.

A FINITE-ELEMENT FORMULATION OF HEATING RATE AND SKIN FRICTION ON THE BASIS OF CONSERVAION LAWS

In the framework of the finite element method (FEM), a prediction method for the heating rate and the skin friction on a body surface is presented by using the energy and momentum conservation equations respectively. Meanwhile, a brief analysis is made of the role the weighted functions play in the present work.

Decline of nucleation in the heating process with a high heating rate

The effect of the heating rate on the nucleation of metallic glass in a rapid heating process starting from the glass transition temperature is investigated. The critical nucleus radius increases with the increase of the temperature of the undercooling liquid. If the increment rate of the critical nucleus radius, owing to the heating process, is higher than the growth rate of the nuclei, the nuclei generated at the low temperature will become the embryos at the high temperature. This means that the high heating rate can make no nucleation happen in the heating process. In consideration of the interfacial energy, the growth rate of the nuclei increases with the increase of their size and the growth rate of the critical nucleus is zero. Thus, the lower heating rate can also make the nuclei decline partially. Finally, this theory is used to analyze the nucleation process during laser remelting metallic glass.

Effects of the Annealing Heating Rate on Sputtered Aluminum Oxide Films

AlxOy films by DC reactive magnetron sputtering were annealed in air ambient at 500 ℃for 1 h with different heating rates of 5,15,and 25 ℃/min.Then heat treatments at 900 ℃ were carried out on these 500 ℃-annealed films to simulate the high-temperature application environment.Effects of the annealing heating rate on structure and properties of both 500 ℃-annealed and 900 ℃-heated films were investigated systematically.It was found that distinct γ-Al2O3 crystallization was observed in the 900 ℃-heated films only when the annealing heating rates are 15 and 25 ℃/min.The 500 ℃-annealed film possessed the most compact surface morphology in the case of 25 ℃/min.The highest microhardness of both 500 ℃-annealed and 900℃-heated films were obtained when the annealing heating rate was 15 ℃/min.

Effects of Heating Rate on Alumina Grain Growth

A rapid-heating method in the absence of electric/magnetic field was achieved by introducing a self-propagating-combustion （SHS） as heating source. The effect of heating rate on the alumina grain growth was explored based on this rapid-heating method. Comparing with the alumina prepared by two different heating ratios （greater than 1 000 ℃/min in SItS and about 50 ℃/min in common pressureless sintering furnace）, it was revealed that the rapid heating could promote the grain growth greatly without pressure during sintering. However, if a pressure was applied simultaneously, the grain growth would be almost completely restrained. Since these observations are quite different from the expectation, a new grain growth model was proposed.

RESEARCH ON RELATION BETWEEN MELTING POINT OF CEMENT CLINKER AND HEATING RATE

The relation between the melting point of Portland cement raw meal and its heating rate have been studied. The raw meal was burnt at different heating rate ranging from 10 similar to 900 degrees C/min Dy the following methods: (A) in electric resistance furnace; (B) in DTA-TG analyzer with infrared ray focused heating; (C) in high temperature microscope with electron stream heating. Based on thermal analysis theory and melt theory and the tests above, it is found that melting point T-m of cement raw meal decreases with the increased heating rate Phi during burning in the following relation: T-m=1280-0.107 empty set.

Effect of heating rate on the recrystallization microstructure and property of ultra-low-carbon steel

In the present work,the microstructure,texture,and mechanical properties of a cold-rolled Ti-IF steel,after annealing at different heating rates,have been investigated.The results reveal that the mean grain size is gradually refined from 19.2 to 16.3 μ m as the heating rate increases from 4 to 50 ℃/s,but refined only slightly at heating rates of over 50 ℃/s.The recrystallization microstructure has a strong texture,which is a result of the sharpening of the favorable { 111 }//ND （normal direction） texture components or γ-fiber.With increasing heating rates,the peak value off（g） of γ-fiber decreases from 17 to 9.The yield and tensile strengths increase gradually as the heating rate increases from 4 to 50 ℃/s,but remain almost unchanged at heating rates of more than 50 ℃/s.The total elongation and uniform elongation increase gradually as the heating rate increases from 4 to 100 ℃/s,but decreases slowly for heating rates higher than 100 ℃/s.As the heating rate increases from 4 to 100 ℃/s,the plastic strain ratio of the steel decreases from 2.8 to 2.2; however,it increases to 2.9 for heating rates above 100 ℃/s.The strain hardening exponent remains unchanged at 0.27 in all annealing cycles.

Measurement of Heating Rates in a Microscopic Surface-Electrode Ion Trap

We report measurement of heating rates of 40 Ca＋ ions confined in our home-made microscopic surface-electrode trap by a Doppler recooling method. The ions are trapped with approximately 800 μm above the surface, and are subjected to heating due to various noises in the trap. There are 3-5 ions involved to measure the heating rates precisely and efficiently. We show the heating rates in variance with the number and the position of the ions as well as the radio-frequency power, which are helpful for understanding the trap imperfection.

Gas release characteristics during carbonization of iron coke hot briquette and influence of heating rate

The release characteristics of CH_(4),H_(2),CO and CO_(2) from iron coke hot briquette(ICHB)during carbonization were studied.The results show that compared with briquette without iron ore,Fe_(3)O_(4) can inhibit the release rate of H2 and promote the production of CO and CO_(2).In addition,when the heating rate increases from 3 to 7℃/min,the release rates of CH4 and H2 increase,while the release rates of CO and CO_(2) first increase and then decrease.The carbonization process of ICHB was segmented,and corresponding kinetic analysis was carried out.The results show that the activation energy of StageⅡand StageⅣis higher in the carbonization process of ICHB,and the active pyrolysis of coal and the reduction of iron ore occur in these two stages.In addition,the effect of heating rate on the kinetic parameters of ICHB carbonization process was investigated.It was found that when the heating rate increased,the reaction activation energy of StageⅣdecreased first and then increased,which was consistent with the release law of CO and CO_(2).The analysis showed that the increase in heating rate leads to more reactions at higher temperatures,resulting in an increase in the release rate of some gases.In addition,thermal hysteresis can also cause some processes to fail to fully react at the end of heating.It is also found that the apparent activation energy and preexponential factor have kinetic compensation effect during the car-bonization of ICHB.

Microstructure and properties of 3D-printed alumina ceramics with different heating rates in vacuum debinding

The effect of heating rates during vacuum debinding on the microstructure and mechanical properties of alumina ceramics are discussed in this paper.The threedimensional(3D)-printed alumina ceramics examined in this study were found to have a layered structure,and interlayer spacing increased as the heating rate increased The pore diameter,shrinkage,flexural strength and hardness were found to decrease as the heating rate increased due to weak interfacial bonding between alumina particles Shrinkage was found to be much larger along the Z direction than along the X or Y directions due to the layer-bylayer forming mode during 3D printing.0.5°C·min-1is considered the optimum heating rate,yielding ceramics with interlayer spacing of 0.65 lm,shrinkage of 2.6%2.3%and 4.0%along the X,Y and Z directions,respectively,flexural strength of 27.5 MPa,hardness of29.8 GPa,Vickers hardness of HV 266.5,pore diameter of356.8 nm,bulk density of 2.5 g·cm-3,and open porosity of38.4%.The debinding procedure used in this study could be used to produce a high-quality ceramic which can be used for fabricating alumina ceramic cores.

Effect of Heating Rate on Microstructure Evolution and Magnetic Properties of Cold Rolled Non-Oriented Electrical Steel

The effects of heating rate （ranging from 50 to 300 ℃/s） during the final annealing process on microstructure evolution and magnetic properties of cold rolled non-oriented electrical steel were investigated. It was found that increasing heating rate increased the nucleation temperature and complete recrystallization temperature. At the same time, heating rate increasing could cause the substantially refined structures for the recrystallization grains and this grain refinement would decline when the heating rate was beyond 50 ℃/s. The recrystallization texture exhibited pronounced improvement with heating rate, such as the intensity decrease of 〈111〉//ND （normal direction） fiber and the intensity increase of { 110}%〈001〉 Goss texture component. The texture improvement and grain size refinement caused by heating rate increasing resulted in complicated variation of the magnetic properties. The magnetic induction （B50） keeps increasing while heating rate increases from 15 to 300 ℃/s which is due to the recrystallized texture optimization caused by rapid heating. The core losses （P1.5/50） decrease while heating rate increases from 15 to 100 ℃/s; however, the core losses would increase when heating rate is higher than 100 ℃/s, which is caused by the mean grain size refinement after rapid heating annealing. The results indicate that recrystallization texture and the magnetic properties of the non-oriented electrical steel can be improved definitely by rapid heating during the final annealing treatment.

Microstructural evolution and mechanism of grain growth in magnesia ceramics prepared by high pressure and temperature with ultra-high heating rate

The fast densification method of combustion reaction plus quick pressing was adopted to prepare nanocrystalline ceramics.The densification process of magnesia compact with a particle size of 100 nm was investigated,under the applied pressure of up to 170 MPa,and the temperature range of 1740–2080 K with ultra-high heating rate(above 1700 K/min).High-purity magnesia ceramics with a relative density of 98.8%and an average grain size of 120 nm was obtained at 1740 K,and the grain growth during the densification process was effectively restrained.The characteristic morphology of evaporation-condensation was observed in the compact prepared at 2080 K,which revealed the actual process of mass transfer by gas diffusion.Moreover,the investigation on the microstructure evolution and mechanism of grain growth was carried out,on the basis of as-preserved nanocrystalline ceramics.The result indicated that the grain growth of the nanocrystalline MgO was controlled by the mechanism of evaporation-condensation rather than surface diffusion.Furthermore,the pressure had an influence of restraining the grain growth based on solid diffusion and strengthening the effect of gas diffusion with the increasing temperature.Under the particular conditions,there existed an appropriate temperature for the densification of nanocrystalline magnesia,while the excessive temperature would exaggerate grain growth and impede densification.

Effect of Heating Rate Before Tempering on Reversed Austenite in Fe-9Ni-C Alloy

The alloy was reheated to 580℃ for tempering at rates of 2 , 5 , 10 , 20 , and 40℃ / s , respectively , after quenching.The amount , distribution , and stability of reversed austenite were investigated by X-ray diffraction ( XRD ) and electron back scatter diffraction ( EBSD ) .The microstructure and cryogenic impact energy were studied by scanning electron microscope ( SEM ), transmission electron microscope ( TEM ) and Charpy V-notch ( CVN ) tests.The results showed that when the sample was heated at 10℃ / s , the volume fraction of reversed austenite exhibited maximum of 8% ; the reversed austenite was uniform along all kinds of boundaries ; the reversed austenite contained higher concentration of carbon which enabled it to be more stable.The cryogenic toughness of the alloy was greatly improved when heated at 10℃ / s , as the fracture surface observation showed that it mainly fractured in ductile rupture mode , which was consistent with the results of cryogenic impact energy.