We report on the room-temperature cascade laser （QCL） at λ -4.7μm. cw operation of a surface grating Both grating design and material distributed feedback （DFB） quantum optimization are used to decrease the thre...We report on the room-temperature cascade laser （QCL） at λ -4.7μm. cw operation of a surface grating Both grating design and material distributed feedback （DFB） quantum optimization are used to decrease the threshold current density and to increase the output power. For a high-reflectivity-coated 13-μm-wide and 4- mm-long laser, high wall-plug efficiency of 6% is obtained at 20℃ from a single facet producing over I W of ew output power. The threshold current density of DFB QCL is as low as 1.13kA/cm^2 at 10℃ and 1.34kA/cm2 at 30℃ in cw mode. Stable single-mode emission with a side-mode suppression ratio of about 30 dB is observed in tile working temperature range of 20-50℃.展开更多
A novel low power and low voltage current mirror with a very low current copy error is presented and the principle of its operation is discussed. In this circuit, the gain boosting regulated cascode scheme is used to ...A novel low power and low voltage current mirror with a very low current copy error is presented and the principle of its operation is discussed. In this circuit, the gain boosting regulated cascode scheme is used to improve the output resistance, while using inverter as an amplifier. The simulation results with HSPICE in TSMC 0.18 μm CMOS technology are given, which verify the high performance of the proposed structure. Simulation results show an input resistance of 0.014 Ω and an output resistance of 3 GΩ. The current copy error is favorable as low as 0.002% together with an input （the minimum input voltage of Vin,min- 0.24 V） and an output （the minimum output voltage of Vout,min~ 0.16 V） compliances while working with the 1 V power supply and the 50 μA input current. The current copy error is near zero at the input current of 27 μA. It consumes only 76μW and introduces a very low output offset current of 50 pA.展开更多
Abstract---The stability of the drive current is very important for a laser driver, while it is difficult to maintain the current stable at a high value for the laser driver. On the other hand, the range of the drive ...Abstract---The stability of the drive current is very important for a laser driver, while it is difficult to maintain the current stable at a high value for the laser driver. On the other hand, the range of the drive current is expected to be as wide as possible to be applied to different kinds of lasers. In this paper, a high current laser driver for the superluminescent light emitting diode （SLED） is presented, which is used in the optic fiber gyro embedded by a 0.35 μm bipolar complementary metal-oxide-semiconductor transistor （BiCMOS） process. The laser driver provides automatic power control and certain value of current determined by the external resister. The system is based on the optic-electric feedback theory and uses the closed-loop control technique to maintain the drive current stable. The system is capable of producing stable current ranges from 4 mA to 200 mA when the value of external resister changes.展开更多
基金Supported by the National Basic Research Program of China under Grant Nos 2013CB632801 and 2013CB632803the National Natural Science Foundation of China under Grant Nos 61435014,61306058 and 61274094the Beijing Natural Science Foundation under Grant No 4144086
文摘We report on the room-temperature cascade laser （QCL） at λ -4.7μm. cw operation of a surface grating Both grating design and material distributed feedback （DFB） quantum optimization are used to decrease the threshold current density and to increase the output power. For a high-reflectivity-coated 13-μm-wide and 4- mm-long laser, high wall-plug efficiency of 6% is obtained at 20℃ from a single facet producing over I W of ew output power. The threshold current density of DFB QCL is as low as 1.13kA/cm^2 at 10℃ and 1.34kA/cm2 at 30℃ in cw mode. Stable single-mode emission with a side-mode suppression ratio of about 30 dB is observed in tile working temperature range of 20-50℃.
基金supported by the Iran University of Science and Technology
文摘A novel low power and low voltage current mirror with a very low current copy error is presented and the principle of its operation is discussed. In this circuit, the gain boosting regulated cascode scheme is used to improve the output resistance, while using inverter as an amplifier. The simulation results with HSPICE in TSMC 0.18 μm CMOS technology are given, which verify the high performance of the proposed structure. Simulation results show an input resistance of 0.014 Ω and an output resistance of 3 GΩ. The current copy error is favorable as low as 0.002% together with an input （the minimum input voltage of Vin,min- 0.24 V） and an output （the minimum output voltage of Vout,min~ 0.16 V） compliances while working with the 1 V power supply and the 50 μA input current. The current copy error is near zero at the input current of 27 μA. It consumes only 76μW and introduces a very low output offset current of 50 pA.
文摘Abstract---The stability of the drive current is very important for a laser driver, while it is difficult to maintain the current stable at a high value for the laser driver. On the other hand, the range of the drive current is expected to be as wide as possible to be applied to different kinds of lasers. In this paper, a high current laser driver for the superluminescent light emitting diode （SLED） is presented, which is used in the optic fiber gyro embedded by a 0.35 μm bipolar complementary metal-oxide-semiconductor transistor （BiCMOS） process. The laser driver provides automatic power control and certain value of current determined by the external resister. The system is based on the optic-electric feedback theory and uses the closed-loop control technique to maintain the drive current stable. The system is capable of producing stable current ranges from 4 mA to 200 mA when the value of external resister changes.
