A superhigh discharge capacity induced by a synergetic effect between high-surface-area carbons and a carbon paper current collector in a lithium–oxygen battery

This paper invesitages the synergetic effect between high-surface-area carbons, such as Ketjan Black(KB) or Super P(SP) carbon materials, and low-surface-area carbon paper(CP) current collectors and it also examines their influence on the discharge performance of nonaqueous Li–O2cells. Ultra-large specific discharge capacities are found in the KB/CP cathodes, which are much greater than those observed in the individual KB or CP cathodes. Detailed analysis indicates that such unexpectedly large capacities result from the synergetic effect between the two components. During the initial discharges of KB or SP materials, a large number of superoxide radical(O·-2) species in the electrolytes and Li2O2 nuclei at the CP surfaces are formed, which activate the CP current collectors to contribute considerable capacities. These results imply that CP could be a superior material for current collectors in terms of its contribution to the overall discharge capacity.On the other hand, we should be careful to calculate the specific capacities of the oxygen cathodes when using CP as a current collector; i.e., ignoring the contribution from the CP may cause overstated discharge capacities.

High discharged energy density of polymer nanocomposites induced by Nd-doped BaTiO_(3)nanoparticles

A flexible polymer nanocomposite has been developed via introducing Nd-doped BaTiO_(3)nanoparticles into the poly(vinylidene fluoride).This nanocomposite delivers a discharged energy density up to 12.5 J/cm^(3)under an electric field of 420 kV/mmwith only a small loading of 1 vol.%Nd-BaTiO_(3).High discharged energy density,mechanical flexibility,light weight,ease fabrication and low cost makes it attractive for advanced microelectronics and electrical power systems.Our results demonstrate that ceramics with giant dielectric permittivity as viable fillers for polymer nanocomposite dielectrics with higher energy density.

Study on High Rate Discharge Performance and Mechanism of AB_5 Type Hydrogen Storage Alloys

The effects of surface treatment, particle size distribution,rare earth composition and B additive on the high rate discharge performance of hydrogen storage alloys were investigated. It is found that the activity, discharge capacity and high rate dischargeability of the alloys are improved after physical and chemical modification as a result of the increase of the surface area and formation of the electrocatalysis layers, which increase both the electrochemical reaction rate on the alloy surface and H diffusion rate in the alloy bulk. It is also found that both the over-coarse and over-fine particle size increase the contact resistance of the electrode, resulting in a decrease of discharge capacity, deterioration of high rate dischargeability and lower discharge plateau. In another word, a suitable particle size distribution can enhance the alloy activity, discharge capacity and high rate dischargeability. In addition, the high rate dischargeability is enhanced by increasing La content and decreasing Ce content of the alloy composition because of enlargement of the unit cell volume and the improvement of the surface activity. Moreover, B additive resultes in the formation of the second phase, and makes the alloys easier pulverization, which greatly improves the activity, discharge capacity and high rate dischargeability.

Probabilistic analysis for the response of nonlinear base isolation system under the ground excitation induced by high dam flood discharge

According to theoretical analysis, a general characteristic of the ground vibration induced by high dam flood discharge is that the dominant frequency ranges over several narrow frequency bands, which is verified by observations from the Xiangjiaba Hydropower Station. Nonlinear base isolation is used to reduce the structure vibration under ground excitation and the advantage of the isolation application is that the low-frequency resonance problem does not need to be considered due to its excitation characteristics, which significantly facilitate the isolation design. In order to obtain the response probabilistic distribution of a nonlinear system, the state space split technique is modified. As only a few degrees of freedom are subjected to the random noise, the probabilistic distribution of the response without involving stochastic excitation is represented by the δ function. Then, the sampling property of the δ function is employed to reduce the dimension of the Fokker-Planck-Kolmogorov （FPK） equation and the low-dimensional FPK equation is solvable with existing methods. Numerical results indicate that the proposed approach is effective and accurate. Moreover, the response probabilistic distributions are more reasonable and scientific than the peak responses calculated by conventional time and frequency domain methods.

CUTTING REGULARITY AND DISCHARGE CHARACTERISTICS BY USING COMPOSITE COOLING LIQUID IN WIRE CUT ELECTRICAL DISCHARGE MACHINE WITH HIGH WIRE TRAVELING SPEED

The analysis of cutting regularity is provided through using and comparing two typical cooling liquids. It is proved that cutting regularity is greatly affected by cooling liquid＇s washing ability. Discharge characteristics and theoretic analysis between two electrodes are also discussed based on discharge waveform. By using composite cooling liquid which has strong washing ability, the efficiency in the first stable cutting phase has reached more than 200 mm^2/min, and the roughness of the surface has reached Ra〈0.8 μm after the fourth cutting with more than 50 mm^2/min average cutting efficiency. It is pointed out that cutting situation of the wire cut electrical discharge machine with high wire traveling speed （HSWEDM） is better than the wire cut electrical discharge machine with low wire traveling speed （LSWEDM） in the condition of improving the cooling liquid washing ability. The machining indices of HSWEDM will be increased remarkably by using the composite cooling liquid.

Discharge characteristic of very high frequency capacitively coupled argon plasma

The discharge characteristics of capacitively coupled argon plasmas driven by very high frequency discharge are studied.The mean electron temperature and electron density are calculated by using the Ar spectral lines at different values of power(20 W-70 W)and four different frequencies(13.56 MHz,40.68 MHz,94.92 MHz,and 100 MHz).The mean electron temperature decreases with the increase of power at a fixed frequency.The mean electron temperature varies non-linearly with frequency increasing at constant power.At 40.68 MHz,the mean electron temperature is the largest.The electron density increases with the increase of power at a fixed frequency.In the cases of driving frequencies of 94.92 MHz and 100 MHz,the obtained electron temperatures are almost the same,so are the electron densities.Particle-in-cell/Monte-Carlo collision(PIC/MCC)method developed within the Vsim 8.0 simulation package is used to simulate the electron density,the potential distribution,and the electron energy probability function(EEPF)under the experimental condition.The sheath width increases with the power increasing.The EEPF of 13.56 MHz and 40.68 MHz are both bi-Maxwellian with a large population of low-energy electrons.The EEPF of 94.92 MHz and 100 MHz are almost the same and both are nearly Maxwellian.

High Frequency Discharge Plasma Induced Grafting of Polystyrene onto Titanium Dioxide Powder

Grafting of polystyrene （PS） onto titanium dioxide powder was investigated. The graft polymerization reaction was induced by high frequency discharge produced N2 plasma treatment of the surfaces of titanium dioxide. IR, XPS and TGA results show that PS was grafted on the titanium dioxide powder. And the crystal structure of the titanium dioxide powder observed by XRD was unchanged after plasma treatment.

Improvement of circuit oscillation generated by underwater high voltage pulse discharges based on pulse power thyristor

High voltage fracturing technology was widely used in the field of reservoir reconstruction due to its advantages of being clean, pollution-free, and high-efficiency. However, high-frequency circuit oscillation occurs during the underwater high voltage pulse discharge process, which brings security risks to the stability of the pulse fracturing system. In order to solve this problem, an underwater pulse power discharge system was established, the circuit oscillation generation conditions were analyzed and the circuit oscillation suppression method was proposed. Firstly, the system structure was introduced and the charging model of the energy storage capacitor was established by the state space average method. Next, the electrode high-voltage breakdown model was established through COMSOL software, the electrode breakdown process was analyzed according to the electron density distribution image, and the plasma channel impedance was estimated based on the conductivity simulation results. Then the underwater pulse power discharge process and the circuit oscillation generation condition were analyzed, and the circuit oscillation suppression strategy of using the thyristor to replace the gas spark switch was proposed. Finally, laboratory experiments were carried out to verify the precision of the theoretical model and the suppression effect of circuit oscillation. The experimental results show that the voltage variation of the energy storage capacitor, the impedance change of the pulse power discharge process, and the equivalent circuit in each discharge stage were consistent with the theoretical model. The proposed oscillation suppression strategy cannot only prevent the damage caused by circuit oscillation but also reduce the damping oscillation time by77.1%, which can greatly improve the stability of the system. This research has potential application value in the field of underwater pulse power discharge for reservoir reconstruction.

Novel Automotive High Intensity Discharge(HID) Lamps with Electronic Ballasts

A new scheme of automotive high intensity discharge(HID) lamps with electronic ballasts is proposed. The design of the proposed ballast and some experimental results are presented. The proposed scheme is consisted of the high frequency DC-DC converter and the low frequency DC-AC inverter. This system separates the input voltage of the ignitor from DC link voltage using auxiliary winding, then it could use the lower voltage rating power devices for HID lamp ballast system and reduce the size of HID lamp ballast. The proposed ballast controller using micro-controller unit(MCU) controls the frequency to operate the DC-DC converter in critical conduction mode, which reduces the noise of the circuit and improves the efficiency by 2%~4%.

Characteristics of fulvic acid by high voltage pulse discharge plasma

High voltage pulse natural organic matter （NOM） toxic by-products. Fulvic acid discharge plasma can remove and produce no production of solution was treated by high voltage pulse discharge plasma in this paper. It was shown that： for the reason of thermolysis and oxidation, the pH and Oxidation Reduction Potential （ORP） of solution decreased gradually with the increase of peak voltage and fulvic acid solution concentration, meanwhile the temperature and turbidity of solution increased gradually. Adding hydrochlorid acid in the treatment could amplify the effect of plasma. When the concentration of NOM as the surrogate parameter, Ultraviolet Absorbancy Degree （UV254） increased slowly by the effect of plasma, while the degradation of Total Organic Carbon （TOC） was first-order reaction. The removal rate of TOC increased from 22.6% to 33.4% by high voltage pulse electrical field of 35 kv, and from 25.6% to 36.7% with the addition of hydrochlorid acid. This paper may provide some basis for the scale-up design of water treatment process by high voltage pulse discharge plasma with other technologies.

Origin of Initial Current Peak in High Power Impulse Magnetron Sputtering and Verification by Non-Sputtering Discharge

A non-sputtering discharge is utilized to verify the effect of replacement of gas ions by metallic ions and consequent decrease in the secondary electron emission coefficient in the discharge current curves in high-power impulse magnetron sputtering （HiPIMS）. In the non-sputtering discharge involving hydrogen, replacement of ions is avoided while the rarefaction still contributes. The initial peak and ensuing decay disappear and all the discharge current curves show a similar feature as the HiPIMS discharge of materials with low sputtering yields such as carbon. The results demonstrate the key effect of ion replacement during sputtering.

Novel High Rate Lithium Intercalation Cathode Materials

Application of amorphous V2O5/carbon/ncodymium oxide （Nd2O3） composite is one ot ways to surmount me lower electrical conductivity of V2O5. A new type of V2O5/carbon/Nd2O3 composite was prepared by mixing vanadium oxide hydrosol, acetone, carbon and Nd2O3 powder. High rate discharge/charge property of the composite electrode was tested electrochemically. This composite with Nd2O3 added shows the improvement of not only the discharge capacity but also cycle durability discharge capacity. The rate capability of the composite cathode also increases with the addition of Nd2O3. Even at 10 A·g^-1 current density, a capacity of about 250 mAh·g^-1 was obtained at 25 ℃. This enhanced rate capability and cycle life are probably caused by the increase in porosity of open pores and short diffusion length of the active material on the lithium-ion insertion.

The Degradation of Organic Pollutants by Bubble Discharge in Water

Organic pollutants could be degraded by using bubble discharge in water with gas aeration in the discharge reactor and more plasma can be generated in the discharge process. When pulsed high voltage was applied between electrodes with gas aerated into the reactor, it showed that bubbles were broken, which meant that breakdown took place. It could also be observed that the removal rate of phenol increased with increasing discharge voltage or pulse frequency, and with reducing initial phenol concentration or solution electric conductivity. It could remove more amount of phenol by oxygen aeration. With increasing oxygen flow rate, the removal rate increased. There was little difference with air or nitrogen aeration for phenol removal. The solution temperature after discharge increased to a great extent. However, this part of energy consumption did not contribute to the reaction, which led to a reduction in the energy utilization efficiency.

Spatiotemporal control of femtosecond laser filament-triggered discharge and its application in diagnosing gas flow fields

Precise control of the discharge in space and time is of great significance for better applications of discharge plasma.Here,we used a femtosecond laser filament to trigger and guide a highvoltage DC pulse discharge to achieve spatiotemporal control of the discharge plasma.In space,the discharge plasma is distributed strictly along the channel generated by the femtosecond laser filament.The breakdown voltage threshold is reduced,and the discharge length is extended.In time,the electrical parameters such as the electrode voltage and the electrode gap affect discharge delay time and jitter.By optimizing the parameters,we can achieve sub-nanosecond jitter of the discharge.Based on the spatiotemporal control of the discharge,we applied filamenttriggered discharge for one-dimensional composition measurements of the gas flow field.Besides,the technique shows great potential in studying the spatiotemporal evolution of discharge plasma.

Theoretical Study on the Characteristics of Atmospheric Radio Frequency Discharges by Altering Electrode Gap

In this paper, we present a theoretical study on the discharge characteristics of radio-frequency discharges at atmospheric pressure driven by a higher frequency of 40.68 MHz while the electrode gap is altered. Based on the analytical equations and simulation data from a one-dimensional fluid model, an optimal gap between electrodes, at which the largest electron density is obtained, can be observed under a constant power condition; however, as the electrode gap increases the time-averaged electron temperature decreases, and the underpinning physics is also discussed based on the simulation results. This study indicates that at a constant power by choosing an appropriate electrode spacing, the rf discharge can be effectively optimized at atmospheric pressure.

High tap density of Ni_3(PO_4)_2 coated LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2 with enhanced cycling performance at high cut-off voltage

The Li Ni1/3Co1/3Mn1/3O2 is first obtained by the controlled crystallization method and then coated with Ni3(PO4)2particles. The effects of the coating on rate capability and cycle life at high cut-off voltage are investigated by electrochemical impedance spectroscopy and galvanostatic measurements. The element ratio of Ni:Mn:Co is tested by inductively-coupled plasma spectrometer(ICP) analysis and it testified to be 1:1:1. It is indicated that Ni3(PO4)2-coated Li Ni1/3Co1/3Mn1/3O2 has an outstanding capacity retention, where 99% capacity retention is maintained after 10 cycles at 5C discharge rate between 2.7 V and 4.6 V. The electrochemical impedance spectroscopy(EIS) results show that the current exchange density i0 of the coated sample is higher than that of Li Ni1/3Co1/3Mn1/3O2, which is beneficial to its electrochemical performances. All the conclusions show that the Ni3(PO4)2coating can prominently enhance the high rate performance of the Li Ni1/3Co1/3Mn1/3O2, especially at high cut-off voltage.

Analysis of Effects of the Arc Voltage on Arc Discharges in a Cathode Ion Source of Neutral Beam Injector

A hot cathode bucket ion source is used for the EAST（experimental advanced superconducting tokamak）neutral beam injector.The thermal electrons emitted from the surface of the cathode are extracted and accelerated by the electric field formed by the arc voltage,which is applied between the arc chamber of the ion source and the cathode.This paper analyzes the effects of arc voltage on the arc discharge in a hot cathode high current ion source.

Structure and electrochemical properties of low-cobalt La_(1-x)Li_xNi_(3.2)Co_(0.3)Al_(0.3) (0≤x≤0.2) hydrogen storage electrode alloys

The structure and electrochemical properties of a new low cobalt hydrogen storage electrode alloys La1-xLixNi3.2Co0.3Al0.3 (0≤x≤0.2) were investigated with a different additions of Li in replacement of La. With the increase of Li contents the maximum discharge capacity increases from 240 mAh·g-1(x=0) to 328.4 mAh·g-1(x=0.1) and the cycle stability is improved correspondingly. The capacity decay can remain 28.6% (x=0.2) after 230 charge/discharge cycles. The high rate discharge(HRD) ability of the alloys(x≤0.1) is improved and the best HRD is 34.1%(x=0.1) under the discharge current density 1200 mA·g-1. It is found that the prepared alloys are basically composed of LaNi5 as matrix phase and LaNi3 as second phase(x≤0.1). But the abundance of LaNi3 phase dramatically decreases with increasing x. When x=0.2, a new phase Al(NiCo)3 is formed.

Recording Spatially Resolved Plasma Parameters in Microwave-Driven Plasmas

In an almost cubical reactor 90 1 in volume which is intended to deposit organic polymers by plasma-enhanced chemical vapor deposition （PECVD）, microwave power is coupled into the volume via a quartz window which extends to approximately 1/10 of the sidewall area. Since the plasma is excited locally, plasma parameters like electron temperature and plasma density are expected to exhibit a spatial variation. The compilation of these plasma quantities has been accomplished with a bendable single Langmuir probe. To isolate the tungsten wire against its grounded housing tube, it was coated with polyparylene. After having compared this construction with our Langmuir probe, which has been now in use for more than a decade, we have taken data of more than half the volume of the reactor with argon and have found a definitive radial inhomogenity for all plasma parameters. To investigate whether this conduct can be determined applying optical emission spectroscopy, we improved our spectrometer which had been used for endpoint detection purposes and plasma diagnostics in chlorine-containing ambients where we could detect also a spatial dependence. This behavior is discussed in terms of Lieberman＇s global model.

Intelligent Controller of Digital High Intensity Discharge Lamp

High intensity discharge (HID) lamps include these types of electrical lamps: mercury vapor, metal halide (also hydraulic quantity indicator),