Investigation of bubbles escape behavior from low basicity mold flux for high-Mn high-Al steels using 3D X-ray microscope

During the continuous casting process of high-Mn high-Al steels,various types of gases such as Ar need to escape through the top of the mold.In which,the behavior of bubbles traversing the liquid slag serves as a restrictive link,closely associated with viscosity and the thickness of liquid slag.In contrast to two-dimensional surface observation,three-dimensional(3D)analysis method can offer a more intuitive,accurate,and comprehensive information.Therefore,this study employs a 3D X-ray microscope(3D-XRM)to obtained spatial distribution and 3D morphological characteristics of residual bubbles in mold flux under different basicity of liquid slag,different temperatures,and different holding times.The results indicate that as basicity of slag increases from 0.52 to 1.03,temperature increases from 1423 to 1573 K,the viscosity of slag decreases,the floating rate of bubbles increases.In addition,when holding time increases from 10 to 30 s,the bubbles floating distance increases,and the volume fraction and average equivalent sphere diameter of the bubbles solidified in the mold flux gradually decreases.In one word,increasing the basicity,temperature,and holding time leading to an increase in the removal rate of bubbles especially for the large.These findings of bubbles escape behavior provide valuable insights into optimizing low basicity mold flux for high-Mn high-Al steels.

Analysis of the Effect of High-Dose Segmental Citrate Anticoagulation in High Flux Hemodialysis

Objective:To analyze the clinical effect of high-dose citrate in segmental extracorporeal anticoagulation for high-throughput hemodialysis.Methods:The subjects included in this study were admitted to the hospital for maintenance hemodialysis treatment from January 2021 to January 2023.All patients had a high risk of bleeding and received 4%trisodium citrate anticoagulant treatment,administered at a rate of 200 mL/h before and after the dialyzer.The anticoagulant effects achieved by the patients were observed and analyzed.Results:The total number of patients who received high-dose segmented citrate extracorporeal anticoagulation dialysis treatment was 50,with each patient undergoing 100 treatments.During the treatment,2 patients had to end the treatment early due to transmembrane pressure exceeding 30 mmHg and an increase in venous pressure exceeding 250 mmHg;the treatment times for these patients were 20 minutes and 200 minutes,respectively.The remaining patients successfully completed the 4-hour treatment.Blood pH and calcium ion concentration in the venous pot were monitored.It was observed that before dialysis,after 2 hours of dialysis,and at the end of dialysis,the blood pH of the patients remained within a relatively normal range.Although some patient levels changed after dialysis,they remained within the normal range.No adverse reactions(such as numbness of the limbs or convulsions)were observed during the anticoagulant treatment.Conclusion:Administering 4%trisodium citrate at a rate of 200 mL/h before and after the dialyzer achieves a good anticoagulant effect,maintains the patient’s blood gas levels within the normal range at the end of dialysis,and causes no adverse reactions.

High X-Ray-to-Optical Flux Ratio Sources From RASS

We present the first results of a program to identify the unknown bright active galactic nuclei (AGN) in the ROSAT All Sky Survey Bright Source Catalog (RASSBSC). We have used lg C+04 R as an alternative expression for lg (f x f opt ), where C is X-ray count rate and R stands for R magnitude. Then a high X-ray-to-optical flux ratio criterion has been used to select an AGN sample with 165 unidentified X-ray sources for optical spectroscopy. At present over 93% of the X-ray sources in the sample have been fully identified in the following classes: emission line AGNs, clusters of galaxies, BL Lacertae objects, and stars.

Evaluation of ultra-fine grained tungsten under transient high heat flux by high-intensity pulsed ion beam

Pure tungsten, oxide dispersion strengthened tungsten and carbide dispersion strengthened tungsten were fabricated by high-energy ball milling and spark plasma sintering process. In order to evaluate the properties of the tungsten alloys under transient high heat flues, four tungsten samples with different grain sizes were tested by high-intensity pulsed ion beam with a heat flux as high as 160 MW/（m^2·s^-1/2）. Compared with the commercial tungsten, the surface modification of the oxide dispersion strengthened tungsten by high-intensity pulsed ion beam is completely different. The oxide dispersion strengthened tungsten shows inferior thermal shock response due to the low melting point second phase of Ti and Y2O3, which results in the surface melting, boiling bubbles and cracking. While the carbide dispersion strengthened tungsten shows better thermal shock response than the commercial tungsten.

PERVAPORATION OF ETHANOL/WATER MIXTURES WITH HIGH FLUX BY ZEOLITE-FILLED PDMS/PVDF COMPOSITE MEMBRANES

Thin-film zeolite-filled silicone/PVDF composite membranes were fabricated by incorporating zeolite particles into PDMS(poly(dimethylsiloxane)) membranes.The morphology of zeolite particles and zeolite filled silicone composite membranes were characterized by SEM.The zeolite-filled PDMS/PVDF composite membranes were applied for the pervaporation of ethanol/water mixtures and showed higher flux compared with that reported in literatures.The effect of zeolite loading and Si/Al ratio of zeolite particles on pe...

Behavior of Brazed W/Cu Mockup Under High Heat Flux Loads

In order to transfer the heat from the armor to the coolant, tungsten has to be connected with a copper heat sink. The joint technology is the most critical issue for manufacturing plasma facing components. Consequently, the reliability of the joints should be verified by a great number of high-heat-flux （HHF） tests to simulate the real load conditions. W/Cu brazed joint technology with sliver free filler metal CuMnNi has been developed at Southwestern Institute of Physics （SWIP）. Screening and thermal fatigue tests of one small-scale fiat tile W/CuCrZr mockup were performed on a 60 kW electron-beam Material testing scenario （EMS-60） constructed recently at SWIP. The module successfully survived screening test with the absorbed power density （Pabs） of 2 MW/m2 to 10 MW/m2 and the following 1000 cycles at Pabs of 7.2 MW/m2 without hot spots and overheating zones during the whole test campaign. Metallurgy and SEM observations did not find any cracks at both sides and the interface, indicating a good bonding of W and CuCrZr alloy. In addition, finite element simulations by ANSYS 12.0 under experimental load conditions were performed and compared with experimental results.

High flux hemodialysis in elderly patients with chronic kidney failure

BACKGROUND Hemodialysis is an advanced blood purification technique to manage kidney failure.However,for conventional hemodialysis,the high prevalence of dyslipidemia may cause cardiovascular diseases and an increase in mortality.Moreover,toxins accumulating in the body over time may induce some complications.High flux hemodialysis can effectively improve disease indexes and clinical symptoms.AIM To investigate the efficacy of high flux hemodialysis in elderly patients with chronic kidney failure(CKF).METHODS A total of 66 elderly patients with CKF who were admitted to our hospital from October 2017 to October 2018 were included in the study.According to the therapies they received,the patients were divided into a study group and a control group with 33 patients in each group.The study group received high flux hemodialysis and the control group received conventional dialysis treatment.Kidney function,toxin levels in serum,and complications were compared in the two groups.RESULTS Before the treatment,there was no significant difference in kidney function,β2-microglobulin,or blood urea nitrogen between the two groups(P>0.05).In contrast,kidney function was better in the study group than in the control group after the treatment(P<0.05).In addition,the study group had significantly lower parathyroid hormone and serum cystatin C than the control group(P<0.05).The incidence of complications was 8.57%in the study group,which was lower than that of the control group(20.00%;P<0.05).CONCLUSION High flux hemodialysis may improve kidney function and reduce toxin levels in serum and the incidence of complications in elderly patients with CKF.

Influence of Late Springtime Surface Sensible Heat Flux Anomalies over the Tibetan and Iranian Plateaus on the Location of the South Asian High in Early Summer

Variation in the location of the South Asian High （SAH） in early boreal summer is strongly influenced by elevated surface heating from the Tibetan Plateau （TP） and the Iranian Plateau （IP）. Based on observational and ERA-Interim data, diagnostic analyses reveal that the interannual northwestward-southeastwaxd （NW-SE） shift of the SAH in June is more closely correlated with the synergistic effect of concurrent surface thermal anomalies over the TP and IP than with each single surface thermal anomaly over either plateau from the preceding May. Concurrent surface thermal anomalies over these two plateaus in May are characterized by a negative correlation between sensible heat flux over most parts of the TP （TPSH） and IP （IPSH）. This anomaly pattern can persist till June and influences the NW-SE shift of the SAH in June through the release of latent heat （LH） over northeastern India. When the IPSH is stronger （weaker） and the TPSH is weaker （stronger） than normal in May, an anomalous cyclone （anticyclone） appears over northern India at 850 hPa, which is accompanied by the ascent （descent） of air and anomalous convergence （divergence） of moisture flux in May and June. Therefore, the LH release over northeastern India is strengthened （weakened） and the vertical gradient of apparent heat source is decreased （increased） in the upper troposphere, which is responsible for the northwestward （southeastward） shift of the SAH in June.

Study on extraction phenol from coal tar with high flux centrifugal extractor

Solvent extraction phenol from coal tar were carried out with novel composite YH-3 as extraction agent, and the high flux centrifugal extractor was used as extraction device. Under the premise of high phenol extraction rate, composite YH-3 extraction agent reduces n-n interaction between phenolic compounds and aromatic hydrocarbons, thus decreasing the entrainment of neutral oil. The optimization of operation conditions, such as the diameter of heavy phase weir HWD, the flow ratio, the total flow rate and the rotation speed, are necessary. For single stage extraction experiment, the mass transfer efficiency was up to 84% while the rate of extraction agent loss was lower than 0.28% with the operation conditions of 29 mm of the heavy phase weir diameter （HWD）, 1：1-1.4：1 of the flow ratio range, 160-200 mL/min of the total flow rate and the rotation speed varied from 2200 to 2600 r/min. For three stage counter-current test, the mass transfer efficiency reached up to 92.6% with the optimum operation condition of 29 mm of the HWD, 1：1 of the flow ratio, 200 rnL/min of the total flow rate and 2400 r/rain of the rotation speed. The results indicated that phenol could be extracted effectively from coal tar in the process of multistage continuous count current centrifugal extraction.

Flux mechanism of compound flux on ash and slag of coal with high ash melting temperature

The melting temperature of Z coal ash was reduced by adding calcium–magnesium compound flux(WCaO/WMgO=1). In the process of simulated coal gasification, the coal ash and slag were prepared. The transformation of minerals in coal ash and slag upon the change of temperature was studied by using X-ray diffraction(XRD). With the increase of temperatures, forsterite in the ash disappears, while the diffraction peak strength of magnesium spinel increases,and the content of the calcium feldspar increases, then the content of the amorphous phase in the ash increases obviously. The species and evolution process of oxygen, silicon, aluminum, calcium, magnesium at different temperatures were analyzed by X-ray photoelectron spectroscopy(XPS). The decrease of the ash melting point mainly affects the structural changes of silicon, aluminum and oxygen. The coordination of aluminum and oxygen in the aluminum element structure, e.g., tetracoordinated aluminum oxide, was changed. Tetrahedral [AlO4] and hexacoordinated aluminoxy octahedral [AlO6] change with the temperature changing. The addition of Ca2+ and Mg2+ destroys silica chain, making bridge oxide silicon change into non-bridge oxysilicon;and bridge oxygen bond was broken and non-bridge oxygen bond was produced in the oxygen element structure. The addition of calcium and magnesium compound flux reacts with aluminum oxide tetrahedron, aluminum oxide octahedron and silicon tetrahedron to promote the breakage of the bridge oxygen bond. Ca2+ and Mg2+ are easily combined with silicon oxide and aluminum oxide tetrahedron and aluminum. Oxygen octahedrons combine with non-oxygen bonds to generate low-melting temperature feldspars and magnesite minerals, thereby reducing the coal ash melting temperatures. The structure of kaolinite and mullite was simulated by quantum chemistry calculation, and kaolinite molecule has a stable structure.

Characteristics of Magnetic Tribology on High Flux Pair of Magnetic Driving Mechanism

The rectangle-like pulsed magnetic field acted on the rubbing pair was presented through analyzing the exciting property in the reciprocating travel. The test of wear in NG-x tester shows that the wear between the electromagnetic core and down magnetic board distributes in the high velocity slip region of reciprocating travel, and the adhesive wear in the low velocity slip region nearby up and down dead points is depressed owing to the presence of high flux magnetic field. The lubrication by magnetic fluid with high permeability effectively reduces the friction and wear of high flux rubbing pair, and improves the conducting property of magnetic circuit constructed by the rubbing pair, which is beneficial to increase the operation performance of magnetic driving mechanism.

Conceptual design and safety characteristics of a new multi-mission high flux research reactor

Research reactors with neutron fluxes higher than 10^(14) n cm^(−2) s^(−1) are widely used in nuclear fuel and material irradiation,neutron-based scientific research,and medical and industrial isotope production.Such high flux research reactors are not only important scientific research facilities for the development of nuclear energy but also represent the national comprehensive technical capability.China has several high flux research reactors that do not satisfy the requirements of nuclear energy development.A high flux research reactor has the following features:a compact core arrangement,high power density,plate-type fuel elements,a short refueling cycle,and high coolant velocity in the core.These characteristics make it difficult to simultaneously realize high neutron flux and optimal safety margin.A new multi-mission high flux research reactor was designed by the Institute of Nuclear and New Energy Technology at Tsinghua University in China;the reactor can simul-taneously realize an average neutron flux higher than 2.0×10^(15) n cm^(−2) s^(−1) and fulfill the current safety criterion.This high flux research reactor features advanced design concepts and has sufficient safety margins according to the preliminary safety analysis.Based on the analysis of the station blackout accident,loss of coolant accident,and reactivity accident of a single-control drum rotating out accidently,the maximum temperature of the cladding surface,minimum departure from nucleate boiling ratio,and temperature difference to the onset of nucleate boiling temperature satisfy the design limits.

Radial Non-uniformity Index Research on High-density,High-flux CFB Riser with Stratified Injection

A high-density, high-flux circulating fluidized bed （CFB） riser （100 mm in ID and 10.614 m in height） was ap- plied in a wide range of operating conditions （with solid fluxes up to 400 kg/m2s and superficial gas velocities up to 12 m/s） to examine its radial non-uniformity dynamics. The solids holdup was determined through the use of a fiber-optic probe at 11 axial levels. The results indicated that under all operating conditions, the high superficial gas velocity and low solid flux- es maintained a low radial non-uniformity index （RNI）. The high-density/flux CFB riser had several unique characteristics, so that the peak of the radial solids holdup profile occurred at a position with r/R=0.8. The RNI and solids holdup at the cross-sectional position had a good logarithmic relationship at the low-density condition （with a mean solids holdup of 〈0.2）, and the RNI decreased when the mean solids holdup exceeded 0.2. Investigation of the dynamics of stratified injec- tion revealed that the feed ratio had an important effect on G, and on solids holdup distribution. A novel ＂〈＂ shaped axial solids holdup profile was found. Gs decreased sharply when the up-flow feed ratio exceeded 0.5, and RNI was lowest when the up-flow feed ratio was 1.

Flux-measuring approach of high temperature metal liquid based on BP neural networks

A soft-measuring approach is presented to measure the flux of liquid zinc with high temperature andcausticity. By constructing mathematical model based on neural networks, weighing the mass of liquid zinc, the fluxof liquid zinc is acquired indirectly, the measuring on line and flux control are realized. Simulation results and indus-trial practice demonstrate that the relative error between the estimated flux value and practical measured flux value islower than 1.5%, meeting the need of industrial process.

High pressure x-ray diffraction techniques with synchrotron radiation

This article summarizes the developments of experimental techniques for high pressure x-ray diffraction（XRD） in diamond anvil cells（DACs） using synchrotron radiation. Basic principles and experimental methods for various diffraction geometry are described, including powder diffraction, single crystal diffraction, radial diffraction, as well as coupling with laser heating system. Resolution in d-spacing of different diffraction modes is discussed. More recent progress, such as extended application of single crystal diffraction for measurements of multigrain and electron density distribution, timeresolved diffraction with dynamic DAC and development of modulated heating techniques are briefly introduced. The current status of the high pressure beamline at BSRF（Beijing Synchrotron Radiation Facility） and some results are also presented.

Applications for Nanoscale X-ray Imaging at High Pressure

Coupling nanoscale transmission X-ray microscopy (nanoTXM) with a diamond anvil cell (DAC) has exciting potential as a powerful three-dimensional probe for non-destructive imaging at high spatial resolution of materials under extreme conditions. In this article, we discuss current developments in high-resolution X-ray imaging and its application in high-pressure nanoTXM experiments in a DAC with third-generation synchrotron X-ray sources, including technical considerations for preparing successful measurements. We then present results from a number of recent in situ high-pressure measurements investigating equations of state (EOS) in amorphous or poorly crystalline materials and in pressureinduced phase transitions and electronic changes. These results illustrate the potential this technique holds for addressing a wide range of research areas, ranging from condensed matter physics and solidstate chemistry to materials science and planetary interiors. Future directions for this exciting technique and opportunities to improve its capabilities for broader application in high-pressure science are discussed.

An in situ high-pressure X-ray diffraction experiment on hydroxyapophyllite

The compression behavior of a natural hydroxyapophyllite is investigated up to about 10.01 GPa at 300 K using in situ angle-dispersive X-ray diffraction and a diamond anvil cell at the High Pressure Experiment Station, Beijing Synchrotron Radiation Facility （BSRF）. Over this pressure range, no phase change or disproportionation is observed. The isothermal equation of state is determined for the first time. The values of zero-pressure volume V0, isothermal bulk modulus K0, and K0＇ refined with a third-order Birch-Mumaghan equation of state are V0 = 1276.3 ± 0.9 A3, K0 = 71± 3 GPa, and K0＇ = 8 ±1. Furthermore, we confirm that the values of linear compressibility β along the a and c directions of hydroxyapophyllite are elastically anisotropic.

Test of a High Throughput Detector on the X-ray Crystal Spectrometer of the EAST

An attempt was made to improve the spatio-temporal resolution of the tangen- tial X-ray crystal spectrometer （XCS） on the Experimental Advanced Superconducting Tokamak （EAST） by evaluating experimentally the applicability of a novel X-ray photon detection tech- nology for measuring the satellite spectra of Ar XVII with a high counting rate. High-resolution experimental data on the profiles of ion temperature and plasma rotation velocity facilitate the studies of the mechanisms underlining important physical phenomena, such as plasma heating, L-H transition and momentum transport. Based on silicon diode array and single-photon counting technology, a relatively small area （83.8 x 33.5 mm~） two-dimensional detector was successfully in- stalled and tested in the recent EAST campaign. X-ray photon counting rate higher than 20 MHz was observed for the first time, and high quality satellite spectra were recorded for ion temperature and plasma rotation measurement, indicating that the new technology is suitable for the next-step high-resolution XCS on EAST, and the deployment of a detector array with a much larger X-ray sensing area is planned for better plasma coverage.

High-pressure effect on inverse spinel LiCuVO_4:X-ray diffraction and Raman scattering

The effect of external quasi-hydrostatic pressure on the inverse spinel structure of LiCuVO4 was studied in this paper. High-pressure synchrotron X-ray diffraction and Raman spectroscopy measurements were carried out at room temperature up to 35.7 and 40.3 GPa, respectively. At a pressure of about 20 GPa, both Raman spectra and X-ray diffraction results indicate that LiCuVO4 was transformed into a monoclinic phase, which remained stable up to at least 35.7 GPa. Upon release of pressure, the high-pressure phase returned to the initial phase. The pressure dependence of the volume of low pressure orthorhombic phase and high-pressure monoclinic phase were described by a second-order Birch-Murnaghan equation of state, which yielded bulk modulus values of B0 = 197 （5） and 232（8） GPa, respectively. The results support the empirical suggestion that the oxide spinels have similar bulk modulus around 200 GPa.

Manufacturing and High Heat Flux Testing of Brazed Flat-Type W/CuCrZr Plasma Facing Components

Water-cooled flat-type W/Cu Cr Zr plasma facing components with an interlayer of oxygen-free copper（OFC） have been developed by using vacuum brazing route.The OFC layer for the accommodation of thermal stresses was cast onto the surface of W at a temperature range of 1150oC-1200 oC in a vacuum furnace.The W/OFC cast tiles were vacuum brazed to a Cu Cr Zr heat sink at 940 oC using the silver-free filler material Cu Mn Si Cr.The microstructure,bonding strength,and high heat flux properties of the brazed W/Cu Cr Zr joint samples were investigated.The W/Cu joint exhibits an average tensile strength of 134 MPa,which is about the same strength as pure annealed copper.High heat flux tests were performed in the electron beam facility EMS-60.Experimental results indicated that the brazed W/Cu Cr Zr mock-up experienced screening tests of up to 15 MW/m^2 and cyclic tests of 9 MW/m^2 for 1000 cycles without visible damage.