This study researches cold rolled ultra high strength martensitic steel processed by water quenching. It is found that both the quenching and overageing temperatures greatly influence the mechanical properties of mart...This study researches cold rolled ultra high strength martensitic steel processed by water quenching. It is found that both the quenching and overageing temperatures greatly influence the mechanical properties of martensitic steel. A tensile strength of 1500 MPa can be obtained from 0.2% C-1.8% Mn steel by soaking at 840℃,quenching at 700℃ and overageing at 200℃ for several minutes. The continuous cooling transformation （CCT） diagram reveals that full martensite can be obtained at a cooling rate of 100℃/s or higher; and at a cooling rate of 3 - 10℃/s,austenite barely decomposes at 700℃. For steel with 0.2% carbon and less manganese, austenite decomposition occurs before it is cooled to 700℃ at a cooling rate of 3 - 10℃/s, which leads to lower tensile strength. It is possible to reduce the manganese content of the 1500 MPa martensitic steel by increasing the quenching temperature. To increase the quenching temperature,the control of flatness during water quenching becomes a major concern.展开更多
Powdering/exfoliating of coatings and scratching galvanized steels and high strength steels （HSS）, are the main forms of surface damage in the forming of which result in increased die maintenance cost and scrap rate...Powdering/exfoliating of coatings and scratching galvanized steels and high strength steels （HSS）, are the main forms of surface damage in the forming of which result in increased die maintenance cost and scrap rate. In this study, a special rectangular box was developed to investigate the behavior and characteristics of surface damage in sheet metal forming （SMF） processes. U-channel forming tests were conducted to study the effect of tool hardness on surface damage in the forming of high strength steels and galvanized steels （hot-dip galvanized and galvannealed steels）. Experimental results indicate that sheet deformation mode influences the severity of surface damage in SMF and surface damage occurs easily at the regions where sheet specimen deforms under the action of compressive stress. Die corner is the position where surface damage initiates. For HSS sheet, surface damage is of major interest due to high forming pressure. The HSS and hot-dip galvanized steels show improved ability of damage-resistance with increased hardness of the forming tool. However, for galvannealed steel it is not the forming tool with the highest hardness value that performs best.展开更多
The use of ultra-high strength steels through sheet metal forming process offers a practical solution to the lightweight design of vehicles.However,sheet metal forming process not only produces desirable changes in ma...The use of ultra-high strength steels through sheet metal forming process offers a practical solution to the lightweight design of vehicles.However,sheet metal forming process not only produces desirable changes in material properties but also causes material damage that may adversely influence the service performance of the material formed.Thus,an investigation is conducted to experimentally quantify such influence for a commonly used steel（the 22MnB5 steel） based on the hot and cold forming processes.For each process,a number of samples are used to conduct a uniaxial tensile test to simulate the forming process.After that,some of the samples are trimmed into a standard shape and then uniaxially extended until fracture to simulate the service stage.Finally,a microstructure test is conducted to analyze the microdefects of the remaining samples.Based on the results of the first two tests,the effect of material damage on the service performance of 22MnB5 steel is analyzed.It is found that the material damages of both the hot and cold forming processes cause reductions in the service performance,such as the failure strain,the ultimate stress,the capacity of energy absorption and the ratio of residual strain.The reductions are generally lower and non-linear in the former process but higher and linear in the latter process.Additionally,it is found from the microstructure analysis that the difference in the reductions of the service performance of 22MnB5 by the two forming processes is driven by the difference in the micro damage mechanisms of the two processes.The findings of this research provide a useful reference in terms of the selection of sheet metal forming processes and the determination of forming parameters for 22MnB5.展开更多
Three different types of tensile strength （TS） 980 MPa grade advanced high-strength steels used in automotive applications, namely, 980MS （ martensite steel ）, 980DP （ dual phase ） and 980QP （ quenching and par...Three different types of tensile strength （TS） 980 MPa grade advanced high-strength steels used in automotive applications, namely, 980MS （ martensite steel ）, 980DP （ dual phase ） and 980QP （ quenching and partitioning） steels were examined. The delayed fracture resistance of the steels was evaluated using a U-bend test, slow strain rate test（SSRT） and a constant load tensile test. The results indicated that all the steels could pass the 300 h HC1 solution immersion test and none of the U-bend specimens was fractured in the test. However,the steels exhibited different susceptibilities to delayed fracture under SSRT and the constant load tensile tests. 980DP exhibited the highest resistance to delayed fracture among all the samples, while 980MS was found to be the most susceptible to delayed fracture.展开更多
Shougang Group has carried out a strategic structure adjustment in order to realize the promise of Chinese people to the Olympic Games.Automotive sheets are chosen as a type of strategic product and an engine to upgra...Shougang Group has carried out a strategic structure adjustment in order to realize the promise of Chinese people to the Olympic Games.Automotive sheets are chosen as a type of strategic product and an engine to upgrade enterprise management,technology and operation to reach the top international level during the transition from long products to steel sheets in Shougang Group.Since 2006,Shougang Group has made an elaborate preparation on steel sheet culture,production line construction,technology import,pilot plant and talent reserve.It lays the foundation for the development of automotive sheets.The developing history of cold rolled automotive sheets is reviewed and the research and development of cold rolled automotive sheets, tackling key problem of defect on surface and the latest progress of automotive sheets construction are described in this paper.The main contents were given as follows:①The products of automotive sheets realize zero breakthrough in Shougang Group.Monthly output was 300 ton in January,2009 and it increased to 48 000 ton in June,2010.The ratio of IF steel sheets increases to 70%from 40%.The proportion of outside panel in automotive sheets occupys more than 15%.②A high emulational pilot plant is used as a product developing platform to develop successfully automotive sheets with 1 000 MPa and below.It guarantees that the industrial development of DP and TRIP sheets gets success at a time.It covers continuous annealing sheets with tensile strength≤780 MPa and galvanizing sheets with tensile strength≤590 MPa.③Individual design is used to meet special requirement of customer.Shougang owns 23 inner brands of LCAK and IF steels.It insures that the grades of yield strength cover whole range from 120 to 270 MPa.It keeps the stabilization of steel performance by means of chemical composition control and high accuracy rolling technology.For example,the strength of soft steel fluctuates within±15 MPa.④The steel sheets with surface grade O5 are produced steadily by solving forming striation of IF steel,grain coarse on surface,edge curling skin and mountains - and - waters painting defects.⑤The safeguard mechanism on quality of products is improved steadily and the output of automotive sheets and outside panel increases greatly by building consistency quality management system、information - system and customer service system.展开更多
文摘This study researches cold rolled ultra high strength martensitic steel processed by water quenching. It is found that both the quenching and overageing temperatures greatly influence the mechanical properties of martensitic steel. A tensile strength of 1500 MPa can be obtained from 0.2% C-1.8% Mn steel by soaking at 840℃,quenching at 700℃ and overageing at 200℃ for several minutes. The continuous cooling transformation （CCT） diagram reveals that full martensite can be obtained at a cooling rate of 100℃/s or higher; and at a cooling rate of 3 - 10℃/s,austenite barely decomposes at 700℃. For steel with 0.2% carbon and less manganese, austenite decomposition occurs before it is cooled to 700℃ at a cooling rate of 3 - 10℃/s, which leads to lower tensile strength. It is possible to reduce the manganese content of the 1500 MPa martensitic steel by increasing the quenching temperature. To increase the quenching temperature,the control of flatness during water quenching becomes a major concern.
基金supported by the National Natural Science Foundation of China under grant No. 50605043
文摘Powdering/exfoliating of coatings and scratching galvanized steels and high strength steels （HSS）, are the main forms of surface damage in the forming of which result in increased die maintenance cost and scrap rate. In this study, a special rectangular box was developed to investigate the behavior and characteristics of surface damage in sheet metal forming （SMF） processes. U-channel forming tests were conducted to study the effect of tool hardness on surface damage in the forming of high strength steels and galvanized steels （hot-dip galvanized and galvannealed steels）. Experimental results indicate that sheet deformation mode influences the severity of surface damage in SMF and surface damage occurs easily at the regions where sheet specimen deforms under the action of compressive stress. Die corner is the position where surface damage initiates. For HSS sheet, surface damage is of major interest due to high forming pressure. The HSS and hot-dip galvanized steels show improved ability of damage-resistance with increased hardness of the forming tool. However, for galvannealed steel it is not the forming tool with the highest hardness value that performs best.
基金Supported by National Natural Science Foundation of China(Grant No.51375201)CSAE(Beijing)Automotive Lightweight Technology Research Institute Development Fund Project of China
文摘The use of ultra-high strength steels through sheet metal forming process offers a practical solution to the lightweight design of vehicles.However,sheet metal forming process not only produces desirable changes in material properties but also causes material damage that may adversely influence the service performance of the material formed.Thus,an investigation is conducted to experimentally quantify such influence for a commonly used steel（the 22MnB5 steel） based on the hot and cold forming processes.For each process,a number of samples are used to conduct a uniaxial tensile test to simulate the forming process.After that,some of the samples are trimmed into a standard shape and then uniaxially extended until fracture to simulate the service stage.Finally,a microstructure test is conducted to analyze the microdefects of the remaining samples.Based on the results of the first two tests,the effect of material damage on the service performance of 22MnB5 steel is analyzed.It is found that the material damages of both the hot and cold forming processes cause reductions in the service performance,such as the failure strain,the ultimate stress,the capacity of energy absorption and the ratio of residual strain.The reductions are generally lower and non-linear in the former process but higher and linear in the latter process.Additionally,it is found from the microstructure analysis that the difference in the reductions of the service performance of 22MnB5 by the two forming processes is driven by the difference in the micro damage mechanisms of the two processes.The findings of this research provide a useful reference in terms of the selection of sheet metal forming processes and the determination of forming parameters for 22MnB5.
文摘Three different types of tensile strength （TS） 980 MPa grade advanced high-strength steels used in automotive applications, namely, 980MS （ martensite steel ）, 980DP （ dual phase ） and 980QP （ quenching and partitioning） steels were examined. The delayed fracture resistance of the steels was evaluated using a U-bend test, slow strain rate test（SSRT） and a constant load tensile test. The results indicated that all the steels could pass the 300 h HC1 solution immersion test and none of the U-bend specimens was fractured in the test. However,the steels exhibited different susceptibilities to delayed fracture under SSRT and the constant load tensile tests. 980DP exhibited the highest resistance to delayed fracture among all the samples, while 980MS was found to be the most susceptible to delayed fracture.
文摘Shougang Group has carried out a strategic structure adjustment in order to realize the promise of Chinese people to the Olympic Games.Automotive sheets are chosen as a type of strategic product and an engine to upgrade enterprise management,technology and operation to reach the top international level during the transition from long products to steel sheets in Shougang Group.Since 2006,Shougang Group has made an elaborate preparation on steel sheet culture,production line construction,technology import,pilot plant and talent reserve.It lays the foundation for the development of automotive sheets.The developing history of cold rolled automotive sheets is reviewed and the research and development of cold rolled automotive sheets, tackling key problem of defect on surface and the latest progress of automotive sheets construction are described in this paper.The main contents were given as follows:①The products of automotive sheets realize zero breakthrough in Shougang Group.Monthly output was 300 ton in January,2009 and it increased to 48 000 ton in June,2010.The ratio of IF steel sheets increases to 70%from 40%.The proportion of outside panel in automotive sheets occupys more than 15%.②A high emulational pilot plant is used as a product developing platform to develop successfully automotive sheets with 1 000 MPa and below.It guarantees that the industrial development of DP and TRIP sheets gets success at a time.It covers continuous annealing sheets with tensile strength≤780 MPa and galvanizing sheets with tensile strength≤590 MPa.③Individual design is used to meet special requirement of customer.Shougang owns 23 inner brands of LCAK and IF steels.It insures that the grades of yield strength cover whole range from 120 to 270 MPa.It keeps the stabilization of steel performance by means of chemical composition control and high accuracy rolling technology.For example,the strength of soft steel fluctuates within±15 MPa.④The steel sheets with surface grade O5 are produced steadily by solving forming striation of IF steel,grain coarse on surface,edge curling skin and mountains - and - waters painting defects.⑤The safeguard mechanism on quality of products is improved steadily and the output of automotive sheets and outside panel increases greatly by building consistency quality management system、information - system and customer service system.
