A high speed steel （HSS） was studied for rollers in this work. The steel was quenched at 1150℃ and tempered at 520℃. The phase structures of the steel were determined by X-ray diffraction （XRD）, and the hardness...A high speed steel （HSS） was studied for rollers in this work. The steel was quenched at 1150℃ and tempered at 520℃. The phase structures of the steel were determined by X-ray diffraction （XRD）, and the hardness of specimens was measured. The volume fraction of carbides was counted by Image-Pro Plus software. The typical microstructures were observed by field emission scanning electron microscope （FESEM）. Stable and meta-stable carbides were deduced by removing the existing phases one by one in the Fe-C equilibrium calculation. It is found that the precipitated carbides are bulk-like MC, long stripe-like M2C, fishbone-like M6C, and daisy-like M7C3 during the tempering process. The stable carbides are MC and M6C, but the meta-stable ones are M2C, M7C3, and M3C.展开更多
The effect of different tempering temperatures on the microstructure and mechanical properties of airquenched high boron white cast iron was studied.The results indicate that the high boron white cast iron comprises d...The effect of different tempering temperatures on the microstructure and mechanical properties of airquenched high boron white cast iron was studied.The results indicate that the high boron white cast iron comprises dendritic matrix and inter-dendritic M 2 B boride;and the matrix comprises martensite and pearlite.After quenching in the air,the matrix is changed into lath martensite;but only 1-μm-size second phase exists in the matrix.After tempering,another second phase of several tens of nanometers is found in the matrix,and the size and quantity increase with an increase in tempering temperature.The two kinds of second precipitation phase with different sizes in the matrix have the same chemical formula,but their forming stages are different.The precipitation phase with larger size forms during the austenitizing process,while the precipitation phase with smaller size forms during the tempering process.When tempered at different temperatures after quenching,the hardness decreases with an increase in the tempering temperature,but it increases a little at 450 ℃ due to the precipitation strengthening effect of the second phase,and it decreases greatly due to the martensite decomposition above 450 ℃.The impact toughness increases a little when tempered below 300 ℃,but it then decreases continuously owing to the increase in size and quantity of the secondary precipitate above 300 ℃.Considered comprehensively,the optimum tempering temperature is suggested at 300 ℃ to obtain a good combination of hardness and toughness.展开更多
Influences of the tempering temperature on the microstructure, mechanical property and wear resistance of High-Boron High Speed Steel (HBHSS) roll materials were investigated by means of optical microscopy, scanning e...Influences of the tempering temperature on the microstructure, mechanical property and wear resistance of High-Boron High Speed Steel (HBHSS) roll materials were investigated by means of optical microscopy, scanning electron microscopy (SEM), X-ray diffraction, hardness measurement, impact tester, tensile tester and pin abrasion tester. The results show that the as-cast structure of HBHSS consists of a great amount of martensite and M2(B,C) and a few retained austenites and M23(B,C)6. After solution treated at 1,050 °C and followed by oil cooling, the amount of M23(B,C)6 carbo-borides in quenched HBHSS increases obviously and the macrohardness of the quenched HBHSS is 66 HRC, which is very close to the 65.8 HRC of as-cast HBHSS. On the whole, the hardness of HBHSS alloy shows a trend of slight decrease with increasing tempering temperature when tempered below 500 °C. While when above 500 °C, the hardness increases slightly as the tempering temperature increases and reaches a peak at 525 °C and then decreases obviously. The impact toughness of HBHSS has a tendency to increase as the tempering temperature increases. Tempering can improve the tensile strength and elongation of HBHSS, but a higher tempering temperature causes a slight decrease in both tensile strength and elongation. Excellent wear resistance can be obtained by tempering at 500 to 550 °C.展开更多
Effect of rare earth metals (REM) on tempering process and decomposition kinetics of martensite and retained austenite of high carbon steel were investigated by DSC technique,based on the non-isothermal kinetic theory...Effect of rare earth metals (REM) on tempering process and decomposition kinetics of martensite and retained austenite of high carbon steel were investigated by DSC technique,based on the non-isothermal kinetic theory.The result shows that the addition of REM in high carbon steel increases the decomposition temperatures of martensite and retained austenite,decreases the thennal effect values,elevates the activity energies and changes the transformation mechanism.展开更多
Conventional fusion arc welding of high-strength quenched and tempered steel can be improved through the use of non-conventional laser beam welding. This article presents the investigations of autogenous bead on plate...Conventional fusion arc welding of high-strength quenched and tempered steel can be improved through the use of non-conventional laser beam welding. This article presents the investigations of autogenous bead on plate and butt CO<sub>2</sub> Laser Welding (LW) of 7 mm thick high-strength quenched and tempered low alloy SM570 (JIS) steel plates. The influence of laser welding parameters, mainly welding speed, defocusing distance and shielding gas flow rate on the weld profile, i.e., weld zone penetration depth and width, microstructure and mechanical properties of welded joints was determined. All welded joints showed smooth and uniform weld beads free from superficial porosity and undercuts. The selected best welding conditions were a laser power of 5.0 kW, welding speed of 500 mm/min, argon gas shielding flow rate of 30 L/min and a defocusing distance of -0.5 mm. It was observed that these conditions gave complete penetration and minimized the width of the weld bead. The microstructure of the welded joints was evaluated by light optical microscopy. The weld metal (WM) and heat-affected zone (HAZ) near weld metal achieved maximum hardness (355 HV). The tensile fractured samples showed the ductile mode of failure and ultimate tensile strength of 580 MPa.展开更多
An artificial neural network(ANN) constitutive model is developed for high strength armor steel tempered at 500 C, 600 C and 650 C based on high strain rate data generated from split Hopkinson pressure bar(SHPB) exper...An artificial neural network(ANN) constitutive model is developed for high strength armor steel tempered at 500 C, 600 C and 650 C based on high strain rate data generated from split Hopkinson pressure bar(SHPB) experiments. A new neural network configuration consisting of both training and validation is effectively employed to predict flow stress. Tempering temperature, strain rate and strain are considered as inputs, whereas flow stress is taken as output of the neural network. A comparative study on Johnsone Cook(Je C) model and neural network model is performed. It was observed that the developed neural network model could predict flow stress under various strain rates and tempering temperatures. The experimental stressestrain data obtained from high strain rate compression tests using SHPB, over a range of tempering temperatures(500e650 C), strains(0.05e0.2) and strain rates(1000e5500/s) are employed to formulate Je C model to predict the high strain rate deformation behavior of high strength armor steels. The J-C model and the back-propagation ANN model were developed to predict the high strain rate deformation behavior of high strength armor steel and their predictability is evaluated in terms of correlation coefficient(R) and average absolute relative error(AARE). R and AARE for the Je C model are found to be 0.7461 and 27.624%, respectively, while R and AARE for the ANN model are 0.9995 and 2.58%, respectively. It was observed that the predictions by ANN model are in consistence with the experimental data for all tempering temperatures.展开更多
The effects of quenching temperature, cooling pattern, temper temperature andtemper times on the structure and properti-es of high speed steel (HSS) rolls have beeninvestigated. The results show that, when the quenchi...The effects of quenching temperature, cooling pattern, temper temperature andtemper times on the structure and properti-es of high speed steel (HSS) rolls have beeninvestigated. The results show that, when the quenching temperature is lower than 1050℃ thehardness of HSS increases with the quenching temperature increasing in oil cooling, but when thequenching temperature exceeds 1100℃ the hardness decreases. In the conditions of salt bath coolingand air cooling, the effect of quenching temperature on the hardness is similar to the above law,but the quenching temperature obtaining the highest hardness is higher than that in oil cooling.When the temper temperature below 350℃ the hardness of HSS has a little change, when above 475℃the hardness will increase with the temper temperature increasing, and the highest hardness isobtained at 525℃. When the temper temperature continues to increase, the hardness decreases. Twicetemper has little effect on the hardness, but three times temper decreases the hardness. HSS in aircooling has lower hardenability, oil cooling can easily produce crackle, and HSS quenching in saltbath has high harde-nability and excellent wear resistance.展开更多
Using the Gleeble 3500 thermal-mechanical system to simulate thermal cycles with different peak temperatures, the hardness and microstructure in the heat-affected zones of two kinds of 100 kg class hot-rolled extra-hi...Using the Gleeble 3500 thermal-mechanical system to simulate thermal cycles with different peak temperatures, the hardness and microstructure in the heat-affected zones of two kinds of 100 kg class hot-rolled extra-high-strength steel were compared. When the peak temperature of the thermal cycle was 800℃ ,incomplete transformation occurred during quenching in both steels, and massive martensite and bainite grains were formed. The hardness was determined by the composition and distribution of the microstructure. The concentration of massive martensite was low, and hence the hardness was low,in steel #1. Conversely,the massive martensite content in steel #2 was high and uniformly distributed,resulting in a high hardness. These findings can provide a reference for improving the mechanical properties in the softened zone.展开更多
基金supported by the National Natural Science Foundation of China (No. 51271163)
文摘A high speed steel （HSS） was studied for rollers in this work. The steel was quenched at 1150℃ and tempered at 520℃. The phase structures of the steel were determined by X-ray diffraction （XRD）, and the hardness of specimens was measured. The volume fraction of carbides was counted by Image-Pro Plus software. The typical microstructures were observed by field emission scanning electron microscope （FESEM）. Stable and meta-stable carbides were deduced by removing the existing phases one by one in the Fe-C equilibrium calculation. It is found that the precipitated carbides are bulk-like MC, long stripe-like M2C, fishbone-like M6C, and daisy-like M7C3 during the tempering process. The stable carbides are MC and M6C, but the meta-stable ones are M2C, M7C3, and M3C.
文摘The effect of different tempering temperatures on the microstructure and mechanical properties of airquenched high boron white cast iron was studied.The results indicate that the high boron white cast iron comprises dendritic matrix and inter-dendritic M 2 B boride;and the matrix comprises martensite and pearlite.After quenching in the air,the matrix is changed into lath martensite;but only 1-μm-size second phase exists in the matrix.After tempering,another second phase of several tens of nanometers is found in the matrix,and the size and quantity increase with an increase in tempering temperature.The two kinds of second precipitation phase with different sizes in the matrix have the same chemical formula,but their forming stages are different.The precipitation phase with larger size forms during the austenitizing process,while the precipitation phase with smaller size forms during the tempering process.When tempered at different temperatures after quenching,the hardness decreases with an increase in the tempering temperature,but it increases a little at 450 ℃ due to the precipitation strengthening effect of the second phase,and it decreases greatly due to the martensite decomposition above 450 ℃.The impact toughness increases a little when tempered below 300 ℃,but it then decreases continuously owing to the increase in size and quantity of the secondary precipitate above 300 ℃.Considered comprehensively,the optimum tempering temperature is suggested at 300 ℃ to obtain a good combination of hardness and toughness.
基金supported by the Scientific Plan Project of Beijing Education Committee (PXM2012- 014204-00-000136, PXM2012-014204-00-000156)the National Natural Science Foundation of China (Grant No. 51054008)Science and Technology Cooperating Project of Yunnan Province, China (Grant No.2010AD012)
文摘Influences of the tempering temperature on the microstructure, mechanical property and wear resistance of High-Boron High Speed Steel (HBHSS) roll materials were investigated by means of optical microscopy, scanning electron microscopy (SEM), X-ray diffraction, hardness measurement, impact tester, tensile tester and pin abrasion tester. The results show that the as-cast structure of HBHSS consists of a great amount of martensite and M2(B,C) and a few retained austenites and M23(B,C)6. After solution treated at 1,050 °C and followed by oil cooling, the amount of M23(B,C)6 carbo-borides in quenched HBHSS increases obviously and the macrohardness of the quenched HBHSS is 66 HRC, which is very close to the 65.8 HRC of as-cast HBHSS. On the whole, the hardness of HBHSS alloy shows a trend of slight decrease with increasing tempering temperature when tempered below 500 °C. While when above 500 °C, the hardness increases slightly as the tempering temperature increases and reaches a peak at 525 °C and then decreases obviously. The impact toughness of HBHSS has a tendency to increase as the tempering temperature increases. Tempering can improve the tensile strength and elongation of HBHSS, but a higher tempering temperature causes a slight decrease in both tensile strength and elongation. Excellent wear resistance can be obtained by tempering at 500 to 550 °C.
文摘Effect of rare earth metals (REM) on tempering process and decomposition kinetics of martensite and retained austenite of high carbon steel were investigated by DSC technique,based on the non-isothermal kinetic theory.The result shows that the addition of REM in high carbon steel increases the decomposition temperatures of martensite and retained austenite,decreases the thennal effect values,elevates the activity energies and changes the transformation mechanism.
文摘Conventional fusion arc welding of high-strength quenched and tempered steel can be improved through the use of non-conventional laser beam welding. This article presents the investigations of autogenous bead on plate and butt CO<sub>2</sub> Laser Welding (LW) of 7 mm thick high-strength quenched and tempered low alloy SM570 (JIS) steel plates. The influence of laser welding parameters, mainly welding speed, defocusing distance and shielding gas flow rate on the weld profile, i.e., weld zone penetration depth and width, microstructure and mechanical properties of welded joints was determined. All welded joints showed smooth and uniform weld beads free from superficial porosity and undercuts. The selected best welding conditions were a laser power of 5.0 kW, welding speed of 500 mm/min, argon gas shielding flow rate of 30 L/min and a defocusing distance of -0.5 mm. It was observed that these conditions gave complete penetration and minimized the width of the weld bead. The microstructure of the welded joints was evaluated by light optical microscopy. The weld metal (WM) and heat-affected zone (HAZ) near weld metal achieved maximum hardness (355 HV). The tensile fractured samples showed the ductile mode of failure and ultimate tensile strength of 580 MPa.
文摘An artificial neural network(ANN) constitutive model is developed for high strength armor steel tempered at 500 C, 600 C and 650 C based on high strain rate data generated from split Hopkinson pressure bar(SHPB) experiments. A new neural network configuration consisting of both training and validation is effectively employed to predict flow stress. Tempering temperature, strain rate and strain are considered as inputs, whereas flow stress is taken as output of the neural network. A comparative study on Johnsone Cook(Je C) model and neural network model is performed. It was observed that the developed neural network model could predict flow stress under various strain rates and tempering temperatures. The experimental stressestrain data obtained from high strain rate compression tests using SHPB, over a range of tempering temperatures(500e650 C), strains(0.05e0.2) and strain rates(1000e5500/s) are employed to formulate Je C model to predict the high strain rate deformation behavior of high strength armor steels. The J-C model and the back-propagation ANN model were developed to predict the high strain rate deformation behavior of high strength armor steel and their predictability is evaluated in terms of correlation coefficient(R) and average absolute relative error(AARE). R and AARE for the Je C model are found to be 0.7461 and 27.624%, respectively, while R and AARE for the ANN model are 0.9995 and 2.58%, respectively. It was observed that the predictions by ANN model are in consistence with the experimental data for all tempering temperatures.
文摘The effects of quenching temperature, cooling pattern, temper temperature andtemper times on the structure and properti-es of high speed steel (HSS) rolls have beeninvestigated. The results show that, when the quenching temperature is lower than 1050℃ thehardness of HSS increases with the quenching temperature increasing in oil cooling, but when thequenching temperature exceeds 1100℃ the hardness decreases. In the conditions of salt bath coolingand air cooling, the effect of quenching temperature on the hardness is similar to the above law,but the quenching temperature obtaining the highest hardness is higher than that in oil cooling.When the temper temperature below 350℃ the hardness of HSS has a little change, when above 475℃the hardness will increase with the temper temperature increasing, and the highest hardness isobtained at 525℃. When the temper temperature continues to increase, the hardness decreases. Twicetemper has little effect on the hardness, but three times temper decreases the hardness. HSS in aircooling has lower hardenability, oil cooling can easily produce crackle, and HSS quenching in saltbath has high harde-nability and excellent wear resistance.
文摘Using the Gleeble 3500 thermal-mechanical system to simulate thermal cycles with different peak temperatures, the hardness and microstructure in the heat-affected zones of two kinds of 100 kg class hot-rolled extra-high-strength steel were compared. When the peak temperature of the thermal cycle was 800℃ ,incomplete transformation occurred during quenching in both steels, and massive martensite and bainite grains were formed. The hardness was determined by the composition and distribution of the microstructure. The concentration of massive martensite was low, and hence the hardness was low,in steel #1. Conversely,the massive martensite content in steel #2 was high and uniformly distributed,resulting in a high hardness. These findings can provide a reference for improving the mechanical properties in the softened zone.
