As drilling wells continue to move into deep ultra-deep layers,the requirements for temperature resistance of drilling fluid treatments are getting higher and higher.Among them,blocking agent,as one of the key treatme...As drilling wells continue to move into deep ultra-deep layers,the requirements for temperature resistance of drilling fluid treatments are getting higher and higher.Among them,blocking agent,as one of the key treatment agents,has also become a hot spot of research.In this study,a high temperature resistant strong adsorption rigid blocking agent(QW-1)was prepared using KH570 modified silica,acrylamide(AM)and allyltrimethylammonium chloride(TMAAC).QW-1 has good thermal stability,average particle size of 1.46μm,water contact angle of 10.5.,has a strong hydrophilicity,can be well dispersed in water.The experimental results showed that when 2 wt%QW-1 was added to recipe A(4 wt%bentonite slurry+0.5 wt%DSP-1(filtration loss depressant)),the API filtration loss decreased from 7.8to 6.4 m L.After aging at 240.C,the API loss of filtration was reduced from 21 to 14 m L,which has certain performance of high temperature loss of filtration.At the same time,it is effective in sealing 80-100mesh and 100-120 mesh sand beds as well as 3 and 5μm ceramic sand discs.Under the same conditions,the blocking performance was superior to silica(5μm)and calcium carbonate(2.6μm).In addition,the mechanism of action of QW-1 was further investigated.The results show that QW-1 with amide and quaternary ammonium groups on the molecular chain can be adsorbed onto the surface of clay particles through hydrogen bonding and electrostatic interaction to form a dense blocking layer,thus preventing further intrusion of drilling fluid into the formation.展开更多
There is currently great optimism within the electronics community that gallium oxide(Ga_(2)O_(3)) ultra-wide bandgap semiconductors have unprecedented prospects for eventually revolutionizing a rich variety of power ...There is currently great optimism within the electronics community that gallium oxide(Ga_(2)O_(3)) ultra-wide bandgap semiconductors have unprecedented prospects for eventually revolutionizing a rich variety of power electronic applications. Specially, benefiting from its ultra-high bandgap of around 4.8 eV, it is expected that the emerging Ga_(2)O_(3) technology would offer an exciting platform to deliver massively enhanced device performance for power electronics and even completely new applications.展开更多
This work develops 2-Phenyl-1H-imidazole-1-sulfonate(PHIS)as a multi-functional electrolyte additive for H2O/HF scavenging and film formation to improve the high temperature performance of LiNi_(0.8)Co_(0.1)Mn_(0.1)O_...This work develops 2-Phenyl-1H-imidazole-1-sulfonate(PHIS)as a multi-functional electrolyte additive for H2O/HF scavenging and film formation to improve the high temperature performance of LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2)/graphite batteries.After 450 cycles at room temperature(25℃),the discharge capacity retentions of batteries with blank and PHIS-containing electrolyte are 56.03%and 94.92%respectively.After 230 cycles at high temperatures(45℃),their values are 75.30%and 88.38%respectively.The enhanced electrochemical performance of the batteries with PHIS-containing electrolyte is supported by the spectroscopic characterization and theoretical calculations.It is demonstrated that this PHIS electrolyte additive can facilitate the construction of the electrode interface films,remove the H2O/HF in the electrolyte,and improve the electrochemical performance of the batteries.This work not only develops a sulfonate-based electrolyte but also can stimulate new ideas of functional additives to improve the battery performance.展开更多
Theoretical and experimental analysis of a new refrigerant mixture BY-3 was conducted based on a single-stage vapor compression refrigeration system. The water-water heat pump system used BY-3 to produce hot water whe...Theoretical and experimental analysis of a new refrigerant mixture BY-3 was conducted based on a single-stage vapor compression refrigeration system. The water-water heat pump system used BY-3 to produce hot water when the low temperature was 20 ℃. The following results were obtained: the highest temperature at the condenser outlet reached about 85 ℃; when the difference between the water temperatures at the condenser outlet and the evaporator inlet was less than 40 ℃, the coefficient of performance (COP) was larger than 4; when the difference reached 55 ℃, the COP still kept 3; the discharge temperature of BY-3 was lower than 100 ℃, and the refrigerant vapor pressure kept lower than 1.8 MPa. When the water temperature at the condenser outlet reached over 85 ℃, nearly a 5 ℃ superheating temperature was maintained.展开更多
The rapid development of electric vehicles demands the development of high performance nickel metal hydride battery that is able to endure high temperature. The discharge properties of Ti 0.7 Zr 0.5 V 0.2 Mn 1.8- x Ni...The rapid development of electric vehicles demands the development of high performance nickel metal hydride battery that is able to endure high temperature. The discharge properties of Ti 0.7 Zr 0.5 V 0.2 Mn 1.8- x Ni x ( x =0.4, 0.8, 1.1, 1.4, 1.7)hydrogen storage alloys was investigated and its phase composition was analyzed using X ray diffraction. The results show that the cycling life was improved as the content of nickel increases. When x =0.4, 0.8, 1.1 and 1.4, the main phase is MgZn 2 type C14 Laves phase and the second one is cubic TiNi phase. When x =1.7, the Laves phase structure disappears. EDAS analysis shows that the increase of nickel content is effective in suppressing the dissolution of vanadium component in alloys. [展开更多
To research the possibility of steel-making dust as a kind of mineral filler in asphalt mixture, two steel-making dusts and one ordinary mineral filler were adopted. The specific density, specific surface area, finene...To research the possibility of steel-making dust as a kind of mineral filler in asphalt mixture, two steel-making dusts and one ordinary mineral filler were adopted. The specific density, specific surface area, fineness modulus and mineralogy component of the dusts were tested. Scanning electron microscopy(SEM) was carried out to research the microstructure of the dusts; dynamic shear rheological(DSR) test and time sweep test were used to research the high temperature and fatigue performance of asphalt mortars containing steel-making dust. The experimental results indicate that, compared with ordinary mineral filler, steel-making dusts have more active ingredients, difference surface characteristics and micro-structure. Furthermore, the high temperature and fatigue performance of steel-making dusts corresponding asphalt mortars are superior to those of reference group. Therefore, the steel-making dust would be an alternative to the ordinary mineral filler to improve the performance of asphalt mortars and reduce the harm of the dusts to the environment at the same time.展开更多
An orthotropic constitutive relationship with temperature parameters for plain highstrength high-performance concrete (HSHPC) under biaxial compression is developed. It is based on the experiments performed for char...An orthotropic constitutive relationship with temperature parameters for plain highstrength high-performance concrete (HSHPC) under biaxial compression is developed. It is based on the experiments performed for characterizing the strength and deformation behavior at two strength levels of HSHPC at 7 different stress ratios including a=σs : σ3=0.00:-1,-0.20:-1,-0.30 : -1,-0.40:-1,-0.50:-1,-0.75:-1,-1.00:-1, after the exposure to normal and high temperatures of 20, 200, 300, 400, 500 and 600℃, and using a large static-dynamic true triaxial machine. The biaxial tests were performed on 100 mm×100 mm×100 mm cubic specimens, and friction-reducing pads were used consisting of three layers of plastic membrane with glycerine in-between for the compressive loading plane. Based on the experimental results, failure modes of HSHPC specimens were described. The principal static compressive strengths, strains at the peak stress and stress-strain curves were measured; and the influence of the temperature and stress ratios on them was also analyzed. The experimental results showed that the uniaxial compressive strength of plain HSHPC after exposure to high temperatures does not decrease dramatically with the increase of temperature. The ratio of the biaxial to its uniaxial compressive strength depends on the stress ratios and brittleness-stiffness of HSHPC after exposure to different temperature levels. Comparison of the stress-strain results obtained from the theoretical model and the experimental data indicates good agreement.展开更多
Ti substituted α-Ni(OH)2(c=2.121nm, a =0.307nm) with perfect high-temperature performance was prepared by the co-precipitation method. The effects of Ti addition on the structure and the electrochemical prope...Ti substituted α-Ni(OH)2(c=2.121nm, a =0.307nm) with perfect high-temperature performance was prepared by the co-precipitation method. The effects of Ti addition on the structure and the electrochemical properties were investigated. The results indicate that the substitution of Ti for Ni leads to the conversion of β-Ni(OH)2 to α-Ni(OH)2 and the increase of the inter layer distance along c-axis from 0.464nm to 0.707nm. Infrared study reveals that more anions(SO2-4 and CO2-3 ions) and H2O exist in the Ti substituted α-Ni(OH)2. The discharge capacity of the Ti substituted α-Ni(OH)2 is 210mA·h/g at 20℃ and reaches up to 270mA·h/g at 80℃ owing to the inhibition of the oxygen evolution at high temperature.展开更多
Low-temperature performance and high-rate discharge capability of AB5-type non-stoichiometric hydrogen storage are studied. X-ray diffraction(XRD),pressure-composition-temperature(PCT) curves and electrochemical imped...Low-temperature performance and high-rate discharge capability of AB5-type non-stoichiometric hydrogen storage are studied. X-ray diffraction(XRD),pressure-composition-temperature(PCT) curves and electrochemical impedance spectroscopy(EIS) are applied to characterize the electrochemical properties of ABx(x=4.8,4.9,5.0,5.1,5.2) alloys. The results show that the non-stoichiometric alloys exhibit better electrochemical properties compared with that of the AB5 alloy.展开更多
Based on the fluidity, strength, heat of hydration and loop crack resistance experiment of multi-powder paste, the components and proportion of multi-powder were optimized and the concrete properties were studied. The...Based on the fluidity, strength, heat of hydration and loop crack resistance experiment of multi-powder paste, the components and proportion of multi-powder were optimized and the concrete properties were studied. The multi-powder consists of limestone powder, slag, fly ash and moderate heat Portland cement (PMH cement). The results show that the compressive strength of the multi-powder paste and mortar is close to those of PMH cement, fly ash paste and mortar currently used in dam concrete, yet the flexural strength is relatively higher. The multi-powder paste is featured by larger fluidity, lower heat of hydration and delayed cracking time. In comparison, less unit water consumption and cement is used in multi-powder concrete, and under premise of equal mechanical performance, deformation, thermal performance and durability, the adiabatic temperature rise at 28 d is reduced by 2 ℃. In this way, the crack resistance is improved and it is feasible both technically and economically to produce HPC for dam concrete.展开更多
A novel phase change heat sink was fabricated for packaging cooling of high power light emitting diode (LED). 3D structures as enhanced boiling structure in the evaporation surface were composed of a spiral micro-gr...A novel phase change heat sink was fabricated for packaging cooling of high power light emitting diode (LED). 3D structures as enhanced boiling structure in the evaporation surface were composed of a spiral micro-groove along circumferential direction and radial micro-grooves which were processed by ploughing-extrusion (P-E) and stamping, respectively. Meanwhile, the cycle power of refrigerant was supplied by wick of sintered copper powder on internal surface of phase change heat sink. Operational characteristics were tested under different heat loads and refrigerants. The experimental results show that phase change heat sink is provided with a good heat transfer capability and the temperature of phase change heat sink reaches 86.8 ℃ under input power of 10 W LED at ambient temperature of 20 ℃.展开更多
The Co(Ⅲ)-coated spherical nickel hydroxide powder is optimum as positive electrode of high power Ni-MH battery because of its excellent property. But the performances at high temperature(above 50 ℃) is still not sa...The Co(Ⅲ)-coated spherical nickel hydroxide powder is optimum as positive electrode of high power Ni-MH battery because of its excellent property. But the performances at high temperature(above 50 ℃) is still not satisfied. In the present paper,the effect of element erbium,used as additive by different methods to prepare positive electrode,on the high temperature performances of the Ni-MH batteries is studied. It is found that the charge acceptance ability of the spherical Ni(OH)2 electrode with element erbium as additive is improved. The discharge capacities of Ni(OH)2 coated with 1%(atomic fraction) Er(OH)3 and mechanically added with 1%(atomic fraction) Er2O3 at 1C are 12.6% and 11.7%,respectively,higher than those of the samples without erbium at 70 ℃.展开更多
High temperature superconducting (HTS) power inductor and its control technology have been studied and analyzed in the paper. Based on the results of simulations and practical experiments, a controlled release schem...High temperature superconducting (HTS) power inductor and its control technology have been studied and analyzed in the paper. Based on the results of simulations and practical experiments, a controlled release scheme has been proposed and verified for developing a practical HTS SMES prototype.展开更多
Effects of flaky rare earth oxide additives including Er2O3,Tm2O3,and Yb2O3,Lu2O3 on high temperature and high rate discharge performance of nickel electrodes were investigated.The discharge efficiency at 0.2C reached...Effects of flaky rare earth oxide additives including Er2O3,Tm2O3,and Yb2O3,Lu2O3 on high temperature and high rate discharge performance of nickel electrodes were investigated.The discharge efficiency at 0.2C reached 96% at 60 oC for electrodes with 1 at.% flaky rare earth oxides.The high rate discharge performance for electrodes with flaky rare earth oxides were improved significantly,for example,discharge efficiency at 5C improved from 50% to 70%.The results showed that the end charging potential of the ...展开更多
The shrinkage behavior of high performance cement concrete made from Portland cement, ultra fine granulated blast furnace slag and pulverized fly ash with addition of superplasticizer at different temperatures from am...The shrinkage behavior of high performance cement concrete made from Portland cement, ultra fine granulated blast furnace slag and pulverized fly ash with addition of superplasticizer at different temperatures from ambient temperature to 120 ℃ under different seuliug conditions was investigated by means of length change measurement on cylindrical concrete specimens along with curing age. Results show that drying shrinkage deformations of titled concrete specimens increased rapidly as the curing temperature rose. The development of dryiing shrinkage deformatian can be efficiently controlled with the aid of aluminum tape sealing as compared with the unsealed specimens, especially when the curing temperature is below 60℃ , although it will increase dramatically when the curing temperature is elevated to above 90%" . Polymer coating on concrete specimens showed a similar effect on the control of drying shrinkage as the sealing operation with aluminum tape.展开更多
The effect Of Y2O3 as additive to the positive electrode on the high-temperature performances of the Ni-MH batteries was studied. The specific capacities of the positive electrode in Ni-MH battery at higher temperatur...The effect Of Y2O3 as additive to the positive electrode on the high-temperature performances of the Ni-MH batteries was studied. The specific capacities of the positive electrode in Ni-MH battery at higher temperatures are much lower than usual. In order to improve high-temperature performances, charge/discharge curves of the Ni(OH)(2) electrodes with different amounts Of Y2O3 it different temperatures were studied. It is found that the specific capacities of the spherical Ni (OH)(2) with Y2O3 as additive are much higher than those of the regular at higher temperatures. The specific capacity of Ni (OH)(2) containing 1% Y2O3 at 0.2C C/D rate is 35% higher than that of the regular. The specific capacity of Ni (OH)(2) containing 0.2% Y2O3 at 1C C/D rate is 15% higher than that of the regular. Mechanism Of Y2O3 improving high temperature performances of Ni(OH)(2) electrode was also discussed in detail.展开更多
The aim of this study is to improve the bond performance of basalt fiber reinforced polymer(BFRP)bars and recycled aggregate concrete(RAC)after being exposed to high temperatures.The bond behavior(failure modes,bond s...The aim of this study is to improve the bond performance of basalt fiber reinforced polymer(BFRP)bars and recycled aggregate concrete(RAC)after being exposed to high temperatures.The bond behavior(failure modes,bond strength,bond stress-slip curves)between BFRP bars and hybrid fiber recycled aggregate concrete(HFRAC)after being exposed to temperatures ranging from 20℃up to 500℃was studied by using pull-out tests.The effect of high temperatures on mechanical properties of concrete(compressive strength,splitting tensile strength)and tensile strength of BFRP bars was also investigated.The bond strength decreased as the temperature increased and the drop of bond strength between RAC and BFRP bar was larger than that between HFRAC and BFRP bar.As the temperature rises,the key factor affecting the bond strength was gradually transformed from concrete strength to BFRP bar strength.The relationship between bond stress and slip in the dimensionless bond stress-slip ascending section was established,which was in good agreement with the experimental results.展开更多
Evaluation of high temperature performance of SBS-modified asphalt mixture was presented.Both wheel loaded method and creep method were adopted for two different mixtures and two kinds of specimens with different heig...Evaluation of high temperature performance of SBS-modified asphalt mixture was presented.Both wheel loaded method and creep method were adopted for two different mixtures and two kinds of specimens with different height,and corresponding indicators were measured.Meanwhile,the correlation between these indicators was thoroughly analyzed and two kinds of mixtures were compared.The experimental results show that there is a good linear relationship between LWT indicators and CT indicators for M-13,while a relatively poor relationship for M-25,especially that between dynamic stiffness and static stiffness and that between dynamic stability and static creep stiffness.Besides,logarithmic relationship between DS and RD has a higher determination coefficient than that for linear relationship.Thus,multi-index evaluation should be taken for synthetically assessing high temperature performance of asphalt mixture.展开更多
The CrN and Cr-Al-Si-N films were deposited on Si wafer and SUS 304 substrates by a hybrid coating system with high power impulse magnetron sputtering (HIPIMS) and a DC pulse sputtering using Cr and AlSi targets under...The CrN and Cr-Al-Si-N films were deposited on Si wafer and SUS 304 substrates by a hybrid coating system with high power impulse magnetron sputtering (HIPIMS) and a DC pulse sputtering using Cr and AlSi targets under N2/Ar atmosphere.By varying the sputtering current of the AlSi target in the range of 0-2.5 A,both the Al and Si contents in the films increased gradually from 0 to 19.1% and 11.1% (mole fraction),respectively.The influences of the AlSi cathode DC pulse current on the microstructure,phase constituents,mechanical properties,and oxidation behaviors of the Cr-Al-Si-N films were investigated systematically.The results indicate that the as-deposited Cr-Al-Si-N films possess the typical nanocomposite structure,namely the face centered cubic (Cr,Al)N nano-crystallites are embedded in the amorphous Si3N4 matrix.With increasing the Al and Si contents,the hardness of the film first increases from 20.8 GPa for the CrN film to the peak value of 29.4 GPa for the Cr0.23Al0.14Si0.07 N film,and then decreases gradually.In the meanwhile,the Cr0.23Al0.14Si0.07N film also possesses excellent high-temperature oxidation resistance that is much better than that of the CrN film at 900 or 1000 °C.展开更多
基金supported by the National Natural Science Foundation of China (No.52074330,No.52288101)。
文摘As drilling wells continue to move into deep ultra-deep layers,the requirements for temperature resistance of drilling fluid treatments are getting higher and higher.Among them,blocking agent,as one of the key treatment agents,has also become a hot spot of research.In this study,a high temperature resistant strong adsorption rigid blocking agent(QW-1)was prepared using KH570 modified silica,acrylamide(AM)and allyltrimethylammonium chloride(TMAAC).QW-1 has good thermal stability,average particle size of 1.46μm,water contact angle of 10.5.,has a strong hydrophilicity,can be well dispersed in water.The experimental results showed that when 2 wt%QW-1 was added to recipe A(4 wt%bentonite slurry+0.5 wt%DSP-1(filtration loss depressant)),the API filtration loss decreased from 7.8to 6.4 m L.After aging at 240.C,the API loss of filtration was reduced from 21 to 14 m L,which has certain performance of high temperature loss of filtration.At the same time,it is effective in sealing 80-100mesh and 100-120 mesh sand beds as well as 3 and 5μm ceramic sand discs.Under the same conditions,the blocking performance was superior to silica(5μm)and calcium carbonate(2.6μm).In addition,the mechanism of action of QW-1 was further investigated.The results show that QW-1 with amide and quaternary ammonium groups on the molecular chain can be adsorbed onto the surface of clay particles through hydrogen bonding and electrostatic interaction to form a dense blocking layer,thus preventing further intrusion of drilling fluid into the formation.
文摘There is currently great optimism within the electronics community that gallium oxide(Ga_(2)O_(3)) ultra-wide bandgap semiconductors have unprecedented prospects for eventually revolutionizing a rich variety of power electronic applications. Specially, benefiting from its ultra-high bandgap of around 4.8 eV, it is expected that the emerging Ga_(2)O_(3) technology would offer an exciting platform to deliver massively enhanced device performance for power electronics and even completely new applications.
基金financially supported by the Scientific and Technological Plan Projects of Guangzhou City(202103040001)。
文摘This work develops 2-Phenyl-1H-imidazole-1-sulfonate(PHIS)as a multi-functional electrolyte additive for H2O/HF scavenging and film formation to improve the high temperature performance of LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2)/graphite batteries.After 450 cycles at room temperature(25℃),the discharge capacity retentions of batteries with blank and PHIS-containing electrolyte are 56.03%and 94.92%respectively.After 230 cycles at high temperatures(45℃),their values are 75.30%and 88.38%respectively.The enhanced electrochemical performance of the batteries with PHIS-containing electrolyte is supported by the spectroscopic characterization and theoretical calculations.It is demonstrated that this PHIS electrolyte additive can facilitate the construction of the electrode interface films,remove the H2O/HF in the electrolyte,and improve the electrochemical performance of the batteries.This work not only develops a sulfonate-based electrolyte but also can stimulate new ideas of functional additives to improve the battery performance.
基金Supported by Major State Basic Research Development Program of China ("973" Program, No. 2009CB219907)the Program for Changjiang Scholars and Innovative Research Team in University (No. IRT0936)
文摘Theoretical and experimental analysis of a new refrigerant mixture BY-3 was conducted based on a single-stage vapor compression refrigeration system. The water-water heat pump system used BY-3 to produce hot water when the low temperature was 20 ℃. The following results were obtained: the highest temperature at the condenser outlet reached about 85 ℃; when the difference between the water temperatures at the condenser outlet and the evaporator inlet was less than 40 ℃, the coefficient of performance (COP) was larger than 4; when the difference reached 55 ℃, the COP still kept 3; the discharge temperature of BY-3 was lower than 100 ℃, and the refrigerant vapor pressure kept lower than 1.8 MPa. When the water temperature at the condenser outlet reached over 85 ℃, nearly a 5 ℃ superheating temperature was maintained.
文摘The rapid development of electric vehicles demands the development of high performance nickel metal hydride battery that is able to endure high temperature. The discharge properties of Ti 0.7 Zr 0.5 V 0.2 Mn 1.8- x Ni x ( x =0.4, 0.8, 1.1, 1.4, 1.7)hydrogen storage alloys was investigated and its phase composition was analyzed using X ray diffraction. The results show that the cycling life was improved as the content of nickel increases. When x =0.4, 0.8, 1.1 and 1.4, the main phase is MgZn 2 type C14 Laves phase and the second one is cubic TiNi phase. When x =1.7, the Laves phase structure disappears. EDAS analysis shows that the increase of nickel content is effective in suppressing the dissolution of vanadium component in alloys. [
基金Funded by the National Natural Science Foundation of China(51778482)
文摘To research the possibility of steel-making dust as a kind of mineral filler in asphalt mixture, two steel-making dusts and one ordinary mineral filler were adopted. The specific density, specific surface area, fineness modulus and mineralogy component of the dusts were tested. Scanning electron microscopy(SEM) was carried out to research the microstructure of the dusts; dynamic shear rheological(DSR) test and time sweep test were used to research the high temperature and fatigue performance of asphalt mortars containing steel-making dust. The experimental results indicate that, compared with ordinary mineral filler, steel-making dusts have more active ingredients, difference surface characteristics and micro-structure. Furthermore, the high temperature and fatigue performance of steel-making dusts corresponding asphalt mortars are superior to those of reference group. Therefore, the steel-making dust would be an alternative to the ordinary mineral filler to improve the performance of asphalt mortars and reduce the harm of the dusts to the environment at the same time.
文摘An orthotropic constitutive relationship with temperature parameters for plain highstrength high-performance concrete (HSHPC) under biaxial compression is developed. It is based on the experiments performed for characterizing the strength and deformation behavior at two strength levels of HSHPC at 7 different stress ratios including a=σs : σ3=0.00:-1,-0.20:-1,-0.30 : -1,-0.40:-1,-0.50:-1,-0.75:-1,-1.00:-1, after the exposure to normal and high temperatures of 20, 200, 300, 400, 500 and 600℃, and using a large static-dynamic true triaxial machine. The biaxial tests were performed on 100 mm×100 mm×100 mm cubic specimens, and friction-reducing pads were used consisting of three layers of plastic membrane with glycerine in-between for the compressive loading plane. Based on the experimental results, failure modes of HSHPC specimens were described. The principal static compressive strengths, strains at the peak stress and stress-strain curves were measured; and the influence of the temperature and stress ratios on them was also analyzed. The experimental results showed that the uniaxial compressive strength of plain HSHPC after exposure to high temperatures does not decrease dramatically with the increase of temperature. The ratio of the biaxial to its uniaxial compressive strength depends on the stress ratios and brittleness-stiffness of HSHPC after exposure to different temperature levels. Comparison of the stress-strain results obtained from the theoretical model and the experimental data indicates good agreement.
文摘Ti substituted α-Ni(OH)2(c=2.121nm, a =0.307nm) with perfect high-temperature performance was prepared by the co-precipitation method. The effects of Ti addition on the structure and the electrochemical properties were investigated. The results indicate that the substitution of Ti for Ni leads to the conversion of β-Ni(OH)2 to α-Ni(OH)2 and the increase of the inter layer distance along c-axis from 0.464nm to 0.707nm. Infrared study reveals that more anions(SO2-4 and CO2-3 ions) and H2O exist in the Ti substituted α-Ni(OH)2. The discharge capacity of the Ti substituted α-Ni(OH)2 is 210mA·h/g at 20℃ and reaches up to 270mA·h/g at 80℃ owing to the inhibition of the oxygen evolution at high temperature.
基金Project(2006AA11A151) supported by the National Hi-Tech Research and Development Program of China
文摘Low-temperature performance and high-rate discharge capability of AB5-type non-stoichiometric hydrogen storage are studied. X-ray diffraction(XRD),pressure-composition-temperature(PCT) curves and electrochemical impedance spectroscopy(EIS) are applied to characterize the electrochemical properties of ABx(x=4.8,4.9,5.0,5.1,5.2) alloys. The results show that the non-stoichiometric alloys exhibit better electrochemical properties compared with that of the AB5 alloy.
基金Project(50879095) supported by the National Natural Science Foundation of China
文摘Based on the fluidity, strength, heat of hydration and loop crack resistance experiment of multi-powder paste, the components and proportion of multi-powder were optimized and the concrete properties were studied. The multi-powder consists of limestone powder, slag, fly ash and moderate heat Portland cement (PMH cement). The results show that the compressive strength of the multi-powder paste and mortar is close to those of PMH cement, fly ash paste and mortar currently used in dam concrete, yet the flexural strength is relatively higher. The multi-powder paste is featured by larger fluidity, lower heat of hydration and delayed cracking time. In comparison, less unit water consumption and cement is used in multi-powder concrete, and under premise of equal mechanical performance, deformation, thermal performance and durability, the adiabatic temperature rise at 28 d is reduced by 2 ℃. In this way, the crack resistance is improved and it is feasible both technically and economically to produce HPC for dam concrete.
基金Projects(50436010,50930005)supported by the National Natural Science Foundation of ChinaProject(U0834002)supported by the Joint Fund of NSFC-Guangdong of China
文摘A novel phase change heat sink was fabricated for packaging cooling of high power light emitting diode (LED). 3D structures as enhanced boiling structure in the evaporation surface were composed of a spiral micro-groove along circumferential direction and radial micro-grooves which were processed by ploughing-extrusion (P-E) and stamping, respectively. Meanwhile, the cycle power of refrigerant was supplied by wick of sintered copper powder on internal surface of phase change heat sink. Operational characteristics were tested under different heat loads and refrigerants. The experimental results show that phase change heat sink is provided with a good heat transfer capability and the temperature of phase change heat sink reaches 86.8 ℃ under input power of 10 W LED at ambient temperature of 20 ℃.
基金Project(2006AA11A151) supported by the National Hi-Tech Research and Development Program of China
文摘The Co(Ⅲ)-coated spherical nickel hydroxide powder is optimum as positive electrode of high power Ni-MH battery because of its excellent property. But the performances at high temperature(above 50 ℃) is still not satisfied. In the present paper,the effect of element erbium,used as additive by different methods to prepare positive electrode,on the high temperature performances of the Ni-MH batteries is studied. It is found that the charge acceptance ability of the spherical Ni(OH)2 electrode with element erbium as additive is improved. The discharge capacities of Ni(OH)2 coated with 1%(atomic fraction) Er(OH)3 and mechanically added with 1%(atomic fraction) Er2O3 at 1C are 12.6% and 11.7%,respectively,higher than those of the samples without erbium at 70 ℃.
文摘High temperature superconducting (HTS) power inductor and its control technology have been studied and analyzed in the paper. Based on the results of simulations and practical experiments, a controlled release scheme has been proposed and verified for developing a practical HTS SMES prototype.
基金supported by the 863 National Research and Development Project Foundation of China (2006AA11A151)
文摘Effects of flaky rare earth oxide additives including Er2O3,Tm2O3,and Yb2O3,Lu2O3 on high temperature and high rate discharge performance of nickel electrodes were investigated.The discharge efficiency at 0.2C reached 96% at 60 oC for electrodes with 1 at.% flaky rare earth oxides.The high rate discharge performance for electrodes with flaky rare earth oxides were improved significantly,for example,discharge efficiency at 5C improved from 50% to 70%.The results showed that the end charging potential of the ...
文摘The shrinkage behavior of high performance cement concrete made from Portland cement, ultra fine granulated blast furnace slag and pulverized fly ash with addition of superplasticizer at different temperatures from ambient temperature to 120 ℃ under different seuliug conditions was investigated by means of length change measurement on cylindrical concrete specimens along with curing age. Results show that drying shrinkage deformations of titled concrete specimens increased rapidly as the curing temperature rose. The development of dryiing shrinkage deformatian can be efficiently controlled with the aid of aluminum tape sealing as compared with the unsealed specimens, especially when the curing temperature is below 60℃ , although it will increase dramatically when the curing temperature is elevated to above 90%" . Polymer coating on concrete specimens showed a similar effect on the control of drying shrinkage as the sealing operation with aluminum tape.
文摘The effect Of Y2O3 as additive to the positive electrode on the high-temperature performances of the Ni-MH batteries was studied. The specific capacities of the positive electrode in Ni-MH battery at higher temperatures are much lower than usual. In order to improve high-temperature performances, charge/discharge curves of the Ni(OH)(2) electrodes with different amounts Of Y2O3 it different temperatures were studied. It is found that the specific capacities of the spherical Ni (OH)(2) with Y2O3 as additive are much higher than those of the regular at higher temperatures. The specific capacity of Ni (OH)(2) containing 1% Y2O3 at 0.2C C/D rate is 35% higher than that of the regular. The specific capacity of Ni (OH)(2) containing 0.2% Y2O3 at 1C C/D rate is 15% higher than that of the regular. Mechanism Of Y2O3 improving high temperature performances of Ni(OH)(2) electrode was also discussed in detail.
基金General Program of National Natural Science Foundation of China(Grant No.51479168)The Natural Science Foundation Project of Liaoning Provincial Department of Education,China(Grant No.JJL201915404).
文摘The aim of this study is to improve the bond performance of basalt fiber reinforced polymer(BFRP)bars and recycled aggregate concrete(RAC)after being exposed to high temperatures.The bond behavior(failure modes,bond strength,bond stress-slip curves)between BFRP bars and hybrid fiber recycled aggregate concrete(HFRAC)after being exposed to temperatures ranging from 20℃up to 500℃was studied by using pull-out tests.The effect of high temperatures on mechanical properties of concrete(compressive strength,splitting tensile strength)and tensile strength of BFRP bars was also investigated.The bond strength decreased as the temperature increased and the drop of bond strength between RAC and BFRP bar was larger than that between HFRAC and BFRP bar.As the temperature rises,the key factor affecting the bond strength was gradually transformed from concrete strength to BFRP bar strength.The relationship between bond stress and slip in the dimensionless bond stress-slip ascending section was established,which was in good agreement with the experimental results.
基金Funded by the National Natural Science Foundation of China (No.50868003)Guangxi Key Laboratory of Architecture Engineering’s Detecting and Testing (No.07109005-9)
文摘Evaluation of high temperature performance of SBS-modified asphalt mixture was presented.Both wheel loaded method and creep method were adopted for two different mixtures and two kinds of specimens with different height,and corresponding indicators were measured.Meanwhile,the correlation between these indicators was thoroughly analyzed and two kinds of mixtures were compared.The experimental results show that there is a good linear relationship between LWT indicators and CT indicators for M-13,while a relatively poor relationship for M-25,especially that between dynamic stiffness and static stiffness and that between dynamic stability and static creep stiffness.Besides,logarithmic relationship between DS and RD has a higher determination coefficient than that for linear relationship.Thus,multi-index evaluation should be taken for synthetically assessing high temperature performance of asphalt mixture.
基金supported by a 2-Year Research Grant of Pusan National University,Korea
文摘The CrN and Cr-Al-Si-N films were deposited on Si wafer and SUS 304 substrates by a hybrid coating system with high power impulse magnetron sputtering (HIPIMS) and a DC pulse sputtering using Cr and AlSi targets under N2/Ar atmosphere.By varying the sputtering current of the AlSi target in the range of 0-2.5 A,both the Al and Si contents in the films increased gradually from 0 to 19.1% and 11.1% (mole fraction),respectively.The influences of the AlSi cathode DC pulse current on the microstructure,phase constituents,mechanical properties,and oxidation behaviors of the Cr-Al-Si-N films were investigated systematically.The results indicate that the as-deposited Cr-Al-Si-N films possess the typical nanocomposite structure,namely the face centered cubic (Cr,Al)N nano-crystallites are embedded in the amorphous Si3N4 matrix.With increasing the Al and Si contents,the hardness of the film first increases from 20.8 GPa for the CrN film to the peak value of 29.4 GPa for the Cr0.23Al0.14Si0.07 N film,and then decreases gradually.In the meanwhile,the Cr0.23Al0.14Si0.07N film also possesses excellent high-temperature oxidation resistance that is much better than that of the CrN film at 900 or 1000 °C.