To elucidate the high temperature rheological capability of graphene modified rubber asphalt,three contents of graphene and crumb rubber were prepared by a combination of mechanical agitation and high speed shearing m...To elucidate the high temperature rheological capability of graphene modified rubber asphalt,three contents of graphene and crumb rubber were prepared by a combination of mechanical agitation and high speed shearing machine,then used dynamic shear rheological test(DSR)and multiple stress creep recovery(MSCR)tests to evaluate.The hardness and softening point with rotational viscosity of samples raised with the addition of graphene,especially the addition of 0.04%.Dynamic shear rheological test revealedthat the dynamic shear modulus G*,rutting factor G*/Sin δ,and zero shear viscosity(ZSV)of graphene-modified rubber asphalt were greatly influenced along with graphene-increased,on the contrary,phase angle δ which characterize the viscoelastic ratio of asphalt decreased.Multiple stress creep recovery(MSCR)tests showed that the graphene-enhanced rubber asphalt had high-temperature stability through non-recoverable creep compliance(Jnr).Based on these findings,graphene-modified rubber asphalt binders with the addition of 0.04% graphene had good viscoelastic properties as well as high temperature rutting resistance performance.In the meantime,G*/Sin δ,ZSV,and Jnr100,Jnr3200 have good correlation,which can reveal the excellent high-temperature stability performance of asphalt.展开更多
With a high energy efficiency,low geometric limitation,and low cracking susceptivity to cracks,wire arc additive manufacturing(WAAM)has become an ideal substitute for casting in the manufacturing of load-bearing high ...With a high energy efficiency,low geometric limitation,and low cracking susceptivity to cracks,wire arc additive manufacturing(WAAM)has become an ideal substitute for casting in the manufacturing of load-bearing high strength aluminum components in aerospace industry.Recently,in scientific researches,the room temperature mechanical performance of additive manufactured high strength aluminum alloys has been continuously broken through,and proves these alloys can achieve comparable or even higher properties than the forged counterpart.Since the aluminum components for aerospace usage experience high-low temperature cycling due to the absence of atmosphere protection,the high temperature performances of additive manufactured high strength aluminum alloys are also important.However,few research focuses on that.A special 2319Ag Sc with 0.4 wt.%Ag and 0.2 wt.%Sc addition designed for high temperature application is deposited successfully via cold metal transfer(CMT)based on WAAM.The microstructures and high temperature tensile properties are investigated.The results show that the as-deposited 2319Ag Sc alloy presents an alternate distribution of columnar grains and equiaxed grains with no significant textures.Main second phases are Al_(2)Cu and Al3Sc,while co-growth of Al_(2)Cu and bulk Al_(3)Sc is found on the grain boundary.During manufacturing,nanoscale Al_(2)Cu can precipitate out from the matrix.Ag and Mg form nano-scaleΩphase on the Al_(2)Cu precipitates.At 260℃,average yield strengths in the horizontal direction and vertical direction are 87 MPa±2 MPa,87 MPa±4 MPa,while average ultimate tensile strengths are 140 MPa±7 MPa,141 MPa±11 MPa,and average elongations are 11.0%±2.5%,13.5%±3.0%.Anisotropy in different directions is weak.展开更多
Fe-Al-Ta eutectic composites with solidification rates of 6,20,30,80 and 200μm/s were obtained by a modified Bridgman directional solidification technique and alloying.Moreover,tensile property and fracture behavior ...Fe-Al-Ta eutectic composites with solidification rates of 6,20,30,80 and 200μm/s were obtained by a modified Bridgman directional solidification technique and alloying.Moreover,tensile property and fracture behavior of Fe-Al-Ta eutectic composites were studied at 600℃.The relationship between mechanical property and microstructure at high temperature was studied.Microstructure of Fe-Al-Ta eutectic is composed of Fe_(2)Ta(Al)Laves phase and Fe(Al,Ta)matrix phase.In addition,the tensile strength at high temperatures is higher than that at room temperature.The tensile strength is increased with the increase of solidification rate.Moreover,fracture morphology transforms from cleavage fracture to dimple fracture as the solidification rate is increased at high temperatures.展开更多
A new experimental method was developed to simulate the generation of the surface transversal crack on the continuous casting slab with a discontinuous sample. A high temperature property of steel named"the sensi...A new experimental method was developed to simulate the generation of the surface transversal crack on the continuous casting slab with a discontinuous sample. A high temperature property of steel named"the sensitivity to the stress concentration of steel at high temperature"was defined to evaluate the effect of stress concentration on thermal plasticity of steel. "The sensitivity parameter to the stress concentration of steel at high temperature"was available to determine the temperature range in which steel is sensitive to the stress concentration.展开更多
The high-temperature performance of iron ore fmes is an important factor in optimizing ore blending in sintering. However, the application of linear regression analysis and the linear combination method in most other ...The high-temperature performance of iron ore fmes is an important factor in optimizing ore blending in sintering. However, the application of linear regression analysis and the linear combination method in most other studies always leads to a large deviation from the desired results. In this study, the fuzzy membership functions of the assimilation ability temperature and the liquid fluidity were proposed based on the fuzzy mathematics theory to construct a model for predicting the high-temperature performance of mixed iron ore. Comparisons of the prediction model and experimental results were presented. The results illustrate that the prediction model is more accurate and effective than previously developed models. In addition, fuzzy constraints for the high-temperature performance of iron ore in this research make the results of ore blending more comparable. A solution for the quantitative calculation as well as the programming of fuzzy constraints is also introduced.展开更多
The aim of this work is firstly to optimize T6 heat-treatment of low-pressure sand-cast Mg-10Gd-3Y-0.5Zr alloy,and then systematically investigate the mechanical behavior of the T6-treated alloy from room temperature ...The aim of this work is firstly to optimize T6 heat-treatment of low-pressure sand-cast Mg-10Gd-3Y-0.5Zr alloy,and then systematically investigate the mechanical behavior of the T6-treated alloy from room temperature to 300℃.It turned out that the optimum T6 heat-treatments for the tested alloy are 525℃×12 h+225℃×14 h and 525℃×12 h+250℃×12 h which integrated age-hardening and tensile properties into account,respectively.The strength of the T6-treated alloy indicates obvious anomalous temperature dependence from room temperature to 300℃,namely both ultimate tensile strength and yield strength of the tested alloy firstly increase with tensile temperature,and then decrease as temperature increases further.Elongation increased with temperature monotonously.The tensile fracture mode of the tested alloy changes from transgranular fracture to intergranular fracture with the increasing of test temperature.展开更多
Al2O3-r2O03/NiCoCrAIYTa coatings were prepared via atmosphere plasma spraying (APS). The microstructure and phase com- position of the coatings were analyzed by X-ray diffraction (XRD), scanning electron microsco...Al2O3-r2O03/NiCoCrAIYTa coatings were prepared via atmosphere plasma spraying (APS). The microstructure and phase com- position of the coatings were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), laser confocal scanning microsco- py (LSCM), and transmission electron microscopy (TEM). The dry frictional wear behavior of the coatings at 500℃ in static air was inves- tigated and compared with that of 0Cr25Ni20 steel. The results show that the coatings comprise the slatted layers of oxide phases, unmelted particles, and pores. The hot abrasive resistance of the coatings is enhanced compared to that of 0Cr25Ni20, and their mass loss is approxi- mately one-fifteenth that of 0Cr25Ni20 steel. The main wear failure mechanisms of the coatings are abrasive wear, fatigue wear, and adhe- sive wear.展开更多
The infiuence of small calcium additions on the high-temperature mechanical behaviour in an extruded Mg-6Zn-l Y(wt.%)alloy reinforced by the I-phase has been investigated.Calcium promotes the formation of the intermet...The infiuence of small calcium additions on the high-temperature mechanical behaviour in an extruded Mg-6Zn-l Y(wt.%)alloy reinforced by the I-phase has been investigated.Calcium promotes the formation of the intermetallic Mg6Zn3Ca2 phase instead of 1-phase,which results in a noticeable improvement of the yield strength and ultimate tensile strength of the alloy above 100℃.The strength of the alloys was analysed taking into account the contribution due to the grain size,the crystallographic texture and the volume fraction and nature of second phase particles.In situ synchrotron radiation diffraction experiments have been used to evaluate the load partitioning between the magnesium matrix and the second phase particles(1-and MgeZgCa?phases)in both alloys.The load transfer from the magnesium matrix towards the MgeZihCa?phase is markedly more effective than that for the I-phase over the entire temperature range,especially at 200°C,temperature at which the reinforcement effect of the I-phase is null.展开更多
The high-temperature mechanical properties and microstructure of forging billets of C-Si-Mn-Cr and C-Si-Mn-Cr-Mo ultra-high-strength cold-rolled steels(tensile strength≥1000 MPa,elongation≥10%) were studied.Throug...The high-temperature mechanical properties and microstructure of forging billets of C-Si-Mn-Cr and C-Si-Mn-Cr-Mo ultra-high-strength cold-rolled steels(tensile strength≥1000 MPa,elongation≥10%) were studied.Through the comparison of reduction in area and hot deformation resistance at 600-1300°C,the Mo-containing steel was found to possess a higher strength and a better plasticity than the Mo-free one.The equilibrium phase diagram and atom fraction of Mo in different phases at different temperatures were calculated by Thermo-Calc software(TCW).The results analyzed by using transmission electron microscopy and TCW show that precipitates in the Mo-containing steel are primarily M23C6,which promote pearlite formation.The experimental data also show that a lower ductility point existing in the Mo-free steel at 850°C is eliminated in the Mo-containing one.This is mainly due to the segregation of Mo at grain boundaries investigated by electron probe microanalysis(EPMA),which improves the strength of grain boundaries.展开更多
Due to the effective precipitation strengthening effect of the β phase, Mg-Gd alloys exhibit excellent room temperature mechanical behaviors. However, when served at high temperatures, the metastable β phase will tr...Due to the effective precipitation strengthening effect of the β phase, Mg-Gd alloys exhibit excellent room temperature mechanical behaviors. However, when served at high temperatures, the metastable β phase will transform to other phases, resulting in severe performance degradation. In this study, we investigated the effect of precipitation state achieved by different heat treatments on high temperature tensile and creep behaviors of the Mg-15Gd alloy by comparing the properties of the as-cast, solid-solutioned(T4) and peak-aged(T6) alloys. The results showed that the tensile mechanical properties of the T6 alloy were always highest from room temperature to 300 ℃, in spite of an abnormal strength increase with temperature existed in the T4 alloy. For tensile creep properties, the T6 alloy exhibited the lowest steady creep rate below 235 ℃ while the T4 alloy possessed the best properties above 260 ℃. Microstructure characterization revealed that the transition was caused by the stress-promoted precipitation of β phase in the T4 alloy and rapid phase transformation in the T6 alloy at high temperatures. At 260 ℃, the calculated stress exponent n was 3.1 and 2.8 for the T4 and T6 alloys, respectively, suggesting the creep deformation mechanism was dislocation slip, which was further confirmed by the microstructure after creeping. Our findings can provide new insights into the heat treatment process of Mg-Gd alloys served at high temperatures.展开更多
The experimental tests for limestone specimens at 700 °C in uniaxial compression were carried out to inves- tigate the mechanical effects of loading rates on limestone by using a MTS810 rock mechanics servo- cont...The experimental tests for limestone specimens at 700 °C in uniaxial compression were carried out to inves- tigate the mechanical effects of loading rates on limestone by using a MTS810 rock mechanics servo- controlled testing system considering the loading rate as a variable. The mechanical properties of limestone such as the stress-strain curve, variable characteristics of peak strength and the modulus of elasticity of limestone were studied under the strain rates ranging from 1.1 10à5 to 1.1 10à1 sà1. (1) Sharp decreases were shown for the peak strength and elastic modulus of limestone from 1.1 10à5 to 1.1 10à4 sà1 at 700 °C as well as a downward trend was shown from 1.1 10à4 to 1.1 10à1 sà1 with the rise of the strain rate. (2) The peak strain increased from 1.1 10à5 to 1.1 10à4 sà1, however, there was no obvious changes shown for the peak strain of limestone from 1.1 10à4 to 1.1 10à1 sà1. These results can provide valuable references for the rock blasting effect and design of mine.展开更多
The high-temperature mechanical properties of near-eutectoid steel were studied with a Cleeble-1500 simu- lation machine. Zero strength temperature (ZST), zero ductility temperature (ZDT), hot ductility curves, an...The high-temperature mechanical properties of near-eutectoid steel were studied with a Cleeble-1500 simu- lation machine. Zero strength temperature (ZST), zero ductility temperature (ZDT), hot ductility curves, and strength curves were measured. Two brittle zones and one plastic zone were found in the temperature range from the melting point to 600℃. Embrittlement in zone I is caused by the existence of liquid film along dendritic interfaces. Ductility loss in zone Ⅲ mainly results from precipitates and inclusions as well as S segregation along grain boundaries. Pearlite transformation also accounts for ductility deterioration in the temperature range of 700-600℃. Moreover, the straightening temperature of the test steel should be higher than 925℃ for avoiding the initiation and propagation of surface cracks in billets.展开更多
High-temperature thermoelectric transport property measurements have been performed on the highly c-axis oriented Bi2Sr2Co20v thin films prepared by pulsed laser deposition on LaA1Oa (001). Both the electric resisti...High-temperature thermoelectric transport property measurements have been performed on the highly c-axis oriented Bi2Sr2Co20v thin films prepared by pulsed laser deposition on LaA1Oa (001). Both the electric resistivity p and the seebeck coefficient S of the film exhibit an increasing trend with the temperature from 300 K-1000 K and reach up to 4.8 m. cm and 202 V/K at 980 K, resulting in a power factor of 0.85 mW/mK which are comparable to those of the single crystalline samples. A small polaron hopping conduction can be responsible for the conduction mechanism of the film at high temperature. The results demonstrate that the Bi2Sr2Co2Oy thin film has potential application has high temperature thin film thermoelectric devices,展开更多
Effects of lanthanum on microstructure and mechanical properties of ZL702 alloy at room and high temperature conditions are studied. The experiment shows that high temperature intermetallics reticularly distributing ...Effects of lanthanum on microstructure and mechanical properties of ZL702 alloy at room and high temperature conditions are studied. The experiment shows that high temperature intermetallics reticularly distributing at grain boundary are formed with La and Al, Si, Fe etc. elements of alloy, which enhances the thermal stability of the alloy. With appropriate content of La (0.10%~ 0.15%), the mechanical properties of the alloy, such as strength, at room temperature and high temperature can be improved.展开更多
Carbon fiber reinforced phenolic based composites were prepared by laminating molding. The variation in mechanical characteristics of composites was evaluated with heating temperature and procedure. The microstructure...Carbon fiber reinforced phenolic based composites were prepared by laminating molding. The variation in mechanical characteristics of composites was evaluated with heating temperature and procedure. The microstructures of composites at different temperatures were observed by optical microscope and scanning electron microscope, respectively. The results showed that the main weight loss range of carbon/phenolic is from 300 to 800 ℃, before 700 ℃ the weight loss was resulted from pyrolysis and after that the weight loss was mainly by oxidation in the fiber phase; with the heat treatment temperature rising, the bonding at the interface of carbon fibers and resin matrix weakened; in the pyrolysis temperature range, the interlaminar shear strength(ILSS) of carbon/phenolic showed a rapid drop with temperature rising, and then decrease in the rate of ILSS became relatively slower; the fiber oxidation had little influence on the ILSS.展开更多
The high temperature mechanical properties(250 ℃) and microstructure of a die-forged Al-5.87 Zn-2.07 Mg-2.42 Cu alloy after T6 heat treatment were investigated. High temperature tensile tests show that as the tempera...The high temperature mechanical properties(250 ℃) and microstructure of a die-forged Al-5.87 Zn-2.07 Mg-2.42 Cu alloy after T6 heat treatment were investigated. High temperature tensile tests show that as the temperature increases from room temperature to 250 ℃, the ultimate tensile strength of the alloy decreases from 638 to 304 MPa, and the elongation rises from 13.6% to 20.4%. Transmission electron microscopy(TEM) and electron backscattered diffraction(EBSD) were applied for microstructure characterization, which indicates that the increase of tensile temperature can lead to the coarsening of precipitates, drop of dislocation density, and increase of dynamic recovery. After tensile testing at 250 ℃, a sub-grain structure composed of a high fraction of small-angle grain boundary is formed.展开更多
The tensile equipment of the advanced confocal scanning laser microscope (CSLM) was used to research the high temperature mechanical properties of low carbon silicon-bearing steel by twin-roll strip casting. The res...The tensile equipment of the advanced confocal scanning laser microscope (CSLM) was used to research the high temperature mechanical properties of low carbon silicon-bearing steel by twin-roll strip casting. The results show that, at the strain rate of 0. 000 5 s ^-1, the strip clearly shows signs of brittleness at around 600 ℃ and its plasticity falls considerably between 750 ℃ and 600 ℃. This is because during the transformation from austenite to ferrite, the low strength ferrite at the austenite grain boundaries greatly reduces the steel' s high temperature plasticity. The subsequent strip coiling process should be controlled at less than the brittle temperature of approximately 600 ℃, so cracks at the coiling stage can be prevented.展开更多
The elevated temperature performances of 2D70 Al alloy hot extrusion rods after two-stage homogenization and intensive deformation were studied by measuring the elevated temperature enduring strength and the creep ult...The elevated temperature performances of 2D70 Al alloy hot extrusion rods after two-stage homogenization and intensive deformation were studied by measuring the elevated temperature enduring strength and the creep ultimate strength. The fracture morphology of some selected samples after testing at different elevated temperatures was observed by scanning electron microscopy (SEM). The results indicate that, as the test temperature increases, the elevated temperature enduring strength of 2D70 Al alloy decreases gradually. In a comparison between 150 C and 240 C, the notch enduring strength drops from 375 to 185 MPa and the smooth enduring strength drops from 337 to 130 MPa. Enduring strength is not sensitive to the notch. The notch sensitivity ratio (NSR) coefficient is in the range of 1.119 to 1.423 from 150 C to 240 C. The creep test results show that, as the test temperature increases from 150 C to 240 C, the creep ultimate strength of 2D70 Al alloy rods drops gradually from 312 to 117 MPa.展开更多
The high temperature tensile and fracture behavior of Zr50Al40Cu10 metallic glass at the temperature range in the vicinity of glass transition were investigated. Tensile tests were carried out at room temperature, 350...The high temperature tensile and fracture behavior of Zr50Al40Cu10 metallic glass at the temperature range in the vicinity of glass transition were investigated. Tensile tests were carried out at room temperature, 350-420 ℃, and in the supercooled liquid region temperature range, respectively. Obvious plastic deformation was initiated at temperature about 80 °C lower than the glass transition temperature. The ultimate tensile strength decreases with the increase of testing temperature and the ductility increases with temperature. At temperature higher than Tg, viscous flow of Non-Newtonian fluid led to super plastic deformation behavior. The deformation process under tension was inhomogeneous, and remarkable serrations were observed on the stress-strain curve near glass transition temperature.展开更多
Self-reinforced Si_3N_4 ceramics containing high oxynitride glass have been fabricated by the control of microstructure evolution and β-Si_3N_4 grain growth. The effects of the size distribution of the elongated β-S...Self-reinforced Si_3N_4 ceramics containing high oxynitride glass have been fabricated by the control of microstructure evolution and β-Si_3N_4 grain growth. The effects of the size distribution of the elongated β-SiaN_4 grains, and the β-Si_3N_4 grain growth as well as the oxynitride glass chemical characteristic on the microstructure and mechanical properties were investigated. The experimental results show that the β-Si_3N_4 grains in high oxynitride glass grow to elongated rod-like crystals and form the stereo-network structure. Under the sintering conditions of 1800℃ and 60 min, a quite uniform microstructure with an average aspect ratio of 6.5 and an average of 1 μm can be obtained. A large amount of oxynitride glass phase with high nitrogen content enhances the elevated temperature fracture toughness because of its high softening temperature and high viscosity. In the present material, the crack deflection and pullout of the elongated rod-like β-Si_3N_4 grains are the primary toughening mechanisms.展开更多
文摘To elucidate the high temperature rheological capability of graphene modified rubber asphalt,three contents of graphene and crumb rubber were prepared by a combination of mechanical agitation and high speed shearing machine,then used dynamic shear rheological test(DSR)and multiple stress creep recovery(MSCR)tests to evaluate.The hardness and softening point with rotational viscosity of samples raised with the addition of graphene,especially the addition of 0.04%.Dynamic shear rheological test revealedthat the dynamic shear modulus G*,rutting factor G*/Sin δ,and zero shear viscosity(ZSV)of graphene-modified rubber asphalt were greatly influenced along with graphene-increased,on the contrary,phase angle δ which characterize the viscoelastic ratio of asphalt decreased.Multiple stress creep recovery(MSCR)tests showed that the graphene-enhanced rubber asphalt had high-temperature stability through non-recoverable creep compliance(Jnr).Based on these findings,graphene-modified rubber asphalt binders with the addition of 0.04% graphene had good viscoelastic properties as well as high temperature rutting resistance performance.In the meantime,G*/Sin δ,ZSV,and Jnr100,Jnr3200 have good correlation,which can reveal the excellent high-temperature stability performance of asphalt.
基金the National Natural Science Foundation of China(Grant No.U21B2080,52305351,52275324)the China Postdoctoral Science Foundation(Grant No.2023M730838)+1 种基金the Heilongjiang Provincial Postdoctoral Science Foundation(Grant No.LBH-Z22128)the Natural Science Foundation of Heilongjiang Province(Grant No.LH2023E039).
文摘With a high energy efficiency,low geometric limitation,and low cracking susceptivity to cracks,wire arc additive manufacturing(WAAM)has become an ideal substitute for casting in the manufacturing of load-bearing high strength aluminum components in aerospace industry.Recently,in scientific researches,the room temperature mechanical performance of additive manufactured high strength aluminum alloys has been continuously broken through,and proves these alloys can achieve comparable or even higher properties than the forged counterpart.Since the aluminum components for aerospace usage experience high-low temperature cycling due to the absence of atmosphere protection,the high temperature performances of additive manufactured high strength aluminum alloys are also important.However,few research focuses on that.A special 2319Ag Sc with 0.4 wt.%Ag and 0.2 wt.%Sc addition designed for high temperature application is deposited successfully via cold metal transfer(CMT)based on WAAM.The microstructures and high temperature tensile properties are investigated.The results show that the as-deposited 2319Ag Sc alloy presents an alternate distribution of columnar grains and equiaxed grains with no significant textures.Main second phases are Al_(2)Cu and Al3Sc,while co-growth of Al_(2)Cu and bulk Al_(3)Sc is found on the grain boundary.During manufacturing,nanoscale Al_(2)Cu can precipitate out from the matrix.Ag and Mg form nano-scaleΩphase on the Al_(2)Cu precipitates.At 260℃,average yield strengths in the horizontal direction and vertical direction are 87 MPa±2 MPa,87 MPa±4 MPa,while average ultimate tensile strengths are 140 MPa±7 MPa,141 MPa±11 MPa,and average elongations are 11.0%±2.5%,13.5%±3.0%.Anisotropy in different directions is weak.
基金Funded by National Natural Science Foundation of China(No.51201121)Key Industry Innovation Chain(group)Project of Shaanxi Province(No.2019ZDLGY 04-04)+1 种基金International Cooperation Project of Key R&D Program in Shaanxi Province(No.2020KW-033)Industrialization Project of Shaanxi Provincial Department of Education(No.20JC024)
文摘Fe-Al-Ta eutectic composites with solidification rates of 6,20,30,80 and 200μm/s were obtained by a modified Bridgman directional solidification technique and alloying.Moreover,tensile property and fracture behavior of Fe-Al-Ta eutectic composites were studied at 600℃.The relationship between mechanical property and microstructure at high temperature was studied.Microstructure of Fe-Al-Ta eutectic is composed of Fe_(2)Ta(Al)Laves phase and Fe(Al,Ta)matrix phase.In addition,the tensile strength at high temperatures is higher than that at room temperature.The tensile strength is increased with the increase of solidification rate.Moreover,fracture morphology transforms from cleavage fracture to dimple fracture as the solidification rate is increased at high temperatures.
文摘A new experimental method was developed to simulate the generation of the surface transversal crack on the continuous casting slab with a discontinuous sample. A high temperature property of steel named"the sensitivity to the stress concentration of steel at high temperature"was defined to evaluate the effect of stress concentration on thermal plasticity of steel. "The sensitivity parameter to the stress concentration of steel at high temperature"was available to determine the temperature range in which steel is sensitive to the stress concentration.
基金financially supported by the National Natural Science Foundation of China (No. 51204013)the National Key Technology R&D Program in the 12th Five Year Plan of China (No. 2011BAC01B02)
文摘The high-temperature performance of iron ore fmes is an important factor in optimizing ore blending in sintering. However, the application of linear regression analysis and the linear combination method in most other studies always leads to a large deviation from the desired results. In this study, the fuzzy membership functions of the assimilation ability temperature and the liquid fluidity were proposed based on the fuzzy mathematics theory to construct a model for predicting the high-temperature performance of mixed iron ore. Comparisons of the prediction model and experimental results were presented. The results illustrate that the prediction model is more accurate and effective than previously developed models. In addition, fuzzy constraints for the high-temperature performance of iron ore in this research make the results of ore blending more comparable. A solution for the quantitative calculation as well as the programming of fuzzy constraints is also introduced.
基金This work is supported by National Natural Science Foundation of China(Nos.51771115 and 51775334)National Science and Technology Major Project(2017ZX04006001)+1 种基金Joint Fund for Space Science and Technology(6141B06300401 and 6141B06310106)Science Innovation Foundation of Shanghai Academy of Spaceflight Technology(No.SAST2016048).
文摘The aim of this work is firstly to optimize T6 heat-treatment of low-pressure sand-cast Mg-10Gd-3Y-0.5Zr alloy,and then systematically investigate the mechanical behavior of the T6-treated alloy from room temperature to 300℃.It turned out that the optimum T6 heat-treatments for the tested alloy are 525℃×12 h+225℃×14 h and 525℃×12 h+250℃×12 h which integrated age-hardening and tensile properties into account,respectively.The strength of the T6-treated alloy indicates obvious anomalous temperature dependence from room temperature to 300℃,namely both ultimate tensile strength and yield strength of the tested alloy firstly increase with tensile temperature,and then decrease as temperature increases further.Elongation increased with temperature monotonously.The tensile fracture mode of the tested alloy changes from transgranular fracture to intergranular fracture with the increasing of test temperature.
基金financially supported by the National High-tech Research and Development Program of China(No.2012AA03A513)the Fundamental Research Funds for the Central Universities(No.N140204001)the National Natural Science Foundation of China(Nos.51371044 and 51301037)
文摘Al2O3-r2O03/NiCoCrAIYTa coatings were prepared via atmosphere plasma spraying (APS). The microstructure and phase com- position of the coatings were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), laser confocal scanning microsco- py (LSCM), and transmission electron microscopy (TEM). The dry frictional wear behavior of the coatings at 500℃ in static air was inves- tigated and compared with that of 0Cr25Ni20 steel. The results show that the coatings comprise the slatted layers of oxide phases, unmelted particles, and pores. The hot abrasive resistance of the coatings is enhanced compared to that of 0Cr25Ni20, and their mass loss is approxi- mately one-fifteenth that of 0Cr25Ni20 steel. The main wear failure mechanisms of the coatings are abrasive wear, fatigue wear, and adhe- sive wear.
基金The authors would like to acknowledge financial support of the Spanish Ministry of Science and Innovation under project number MAT2016-78850-RWe would like to acknowledge the expert support of A.Garcia,A.Tomas and M.Maier for assistance with SEM.The Deutches Elektronen-Synchrotron DESY is acknowledged for the provision of beamtime at the P07 beamline of the PETRA III synchrotron facility in the framework of proposal I-20170054EC.
文摘The infiuence of small calcium additions on the high-temperature mechanical behaviour in an extruded Mg-6Zn-l Y(wt.%)alloy reinforced by the I-phase has been investigated.Calcium promotes the formation of the intermetallic Mg6Zn3Ca2 phase instead of 1-phase,which results in a noticeable improvement of the yield strength and ultimate tensile strength of the alloy above 100℃.The strength of the alloys was analysed taking into account the contribution due to the grain size,the crystallographic texture and the volume fraction and nature of second phase particles.In situ synchrotron radiation diffraction experiments have been used to evaluate the load partitioning between the magnesium matrix and the second phase particles(1-and MgeZgCa?phases)in both alloys.The load transfer from the magnesium matrix towards the MgeZihCa?phase is markedly more effective than that for the I-phase over the entire temperature range,especially at 200°C,temperature at which the reinforcement effect of the I-phase is null.
基金supported by the National High-tech Research and Development Program of China (No.2009AA03Z518)
文摘The high-temperature mechanical properties and microstructure of forging billets of C-Si-Mn-Cr and C-Si-Mn-Cr-Mo ultra-high-strength cold-rolled steels(tensile strength≥1000 MPa,elongation≥10%) were studied.Through the comparison of reduction in area and hot deformation resistance at 600-1300°C,the Mo-containing steel was found to possess a higher strength and a better plasticity than the Mo-free one.The equilibrium phase diagram and atom fraction of Mo in different phases at different temperatures were calculated by Thermo-Calc software(TCW).The results analyzed by using transmission electron microscopy and TCW show that precipitates in the Mo-containing steel are primarily M23C6,which promote pearlite formation.The experimental data also show that a lower ductility point existing in the Mo-free steel at 850°C is eliminated in the Mo-containing one.This is mainly due to the segregation of Mo at grain boundaries investigated by electron probe microanalysis(EPMA),which improves the strength of grain boundaries.
基金supported by the National Natural Science Foundation of China (Grant No. 51771152)the National Key Research and Development Program of China (Grant No. 2018YFB1106800)。
文摘Due to the effective precipitation strengthening effect of the β phase, Mg-Gd alloys exhibit excellent room temperature mechanical behaviors. However, when served at high temperatures, the metastable β phase will transform to other phases, resulting in severe performance degradation. In this study, we investigated the effect of precipitation state achieved by different heat treatments on high temperature tensile and creep behaviors of the Mg-15Gd alloy by comparing the properties of the as-cast, solid-solutioned(T4) and peak-aged(T6) alloys. The results showed that the tensile mechanical properties of the T6 alloy were always highest from room temperature to 300 ℃, in spite of an abnormal strength increase with temperature existed in the T4 alloy. For tensile creep properties, the T6 alloy exhibited the lowest steady creep rate below 235 ℃ while the T4 alloy possessed the best properties above 260 ℃. Microstructure characterization revealed that the transition was caused by the stress-promoted precipitation of β phase in the T4 alloy and rapid phase transformation in the T6 alloy at high temperatures. At 260 ℃, the calculated stress exponent n was 3.1 and 2.8 for the T4 and T6 alloys, respectively, suggesting the creep deformation mechanism was dislocation slip, which was further confirmed by the microstructure after creeping. Our findings can provide new insights into the heat treatment process of Mg-Gd alloys served at high temperatures.
基金supported by the Fundamental Research Funds for the Central Universities (No. 2011QNB05)the National Basic Research Program of China (No. 2007CB209400)+2 种基金the National Natural Science Foundation of China (Nos. 51074166 and 51104128)the Research Project for Ministry of Housing and Urban-Rural Development of China (No. 2011-K3-5)the Innovation Project of Graduate Students in Jiangsu Province (No. CX09B_108Z)
文摘The experimental tests for limestone specimens at 700 °C in uniaxial compression were carried out to inves- tigate the mechanical effects of loading rates on limestone by using a MTS810 rock mechanics servo- controlled testing system considering the loading rate as a variable. The mechanical properties of limestone such as the stress-strain curve, variable characteristics of peak strength and the modulus of elasticity of limestone were studied under the strain rates ranging from 1.1 10à5 to 1.1 10à1 sà1. (1) Sharp decreases were shown for the peak strength and elastic modulus of limestone from 1.1 10à5 to 1.1 10à4 sà1 at 700 °C as well as a downward trend was shown from 1.1 10à4 to 1.1 10à1 sà1 with the rise of the strain rate. (2) The peak strain increased from 1.1 10à5 to 1.1 10à4 sà1, however, there was no obvious changes shown for the peak strain of limestone from 1.1 10à4 to 1.1 10à1 sà1. These results can provide valuable references for the rock blasting effect and design of mine.
基金financially supported by the National High Technology Research and Development Program of China(No.2013AA031601)
文摘The high-temperature mechanical properties of near-eutectoid steel were studied with a Cleeble-1500 simu- lation machine. Zero strength temperature (ZST), zero ductility temperature (ZDT), hot ductility curves, and strength curves were measured. Two brittle zones and one plastic zone were found in the temperature range from the melting point to 600℃. Embrittlement in zone I is caused by the existence of liquid film along dendritic interfaces. Ductility loss in zone Ⅲ mainly results from precipitates and inclusions as well as S segregation along grain boundaries. Pearlite transformation also accounts for ductility deterioration in the temperature range of 700-600℃. Moreover, the straightening temperature of the test steel should be higher than 925℃ for avoiding the initiation and propagation of surface cracks in billets.
基金Project supported by the Young Scientists Fund of the National Natural Science Foundation of China (Grant No. 10904030)the Specialized Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20091301120002)
文摘High-temperature thermoelectric transport property measurements have been performed on the highly c-axis oriented Bi2Sr2Co20v thin films prepared by pulsed laser deposition on LaA1Oa (001). Both the electric resistivity p and the seebeck coefficient S of the film exhibit an increasing trend with the temperature from 300 K-1000 K and reach up to 4.8 m. cm and 202 V/K at 980 K, resulting in a power factor of 0.85 mW/mK which are comparable to those of the single crystalline samples. A small polaron hopping conduction can be responsible for the conduction mechanism of the film at high temperature. The results demonstrate that the Bi2Sr2Co2Oy thin film has potential application has high temperature thin film thermoelectric devices,
文摘Effects of lanthanum on microstructure and mechanical properties of ZL702 alloy at room and high temperature conditions are studied. The experiment shows that high temperature intermetallics reticularly distributing at grain boundary are formed with La and Al, Si, Fe etc. elements of alloy, which enhances the thermal stability of the alloy. With appropriate content of La (0.10%~ 0.15%), the mechanical properties of the alloy, such as strength, at room temperature and high temperature can be improved.
基金the Innovation Foundation of Postgraduate of Jiangsu Province,China(No.CX08B_134Z)Beforehand Research Fund of Defense Technology(No.404040301)The Fundamental Research Funds for the Central Universities(No.NUST2011XQTR13)
文摘Carbon fiber reinforced phenolic based composites were prepared by laminating molding. The variation in mechanical characteristics of composites was evaluated with heating temperature and procedure. The microstructures of composites at different temperatures were observed by optical microscope and scanning electron microscope, respectively. The results showed that the main weight loss range of carbon/phenolic is from 300 to 800 ℃, before 700 ℃ the weight loss was resulted from pyrolysis and after that the weight loss was mainly by oxidation in the fiber phase; with the heat treatment temperature rising, the bonding at the interface of carbon fibers and resin matrix weakened; in the pyrolysis temperature range, the interlaminar shear strength(ILSS) of carbon/phenolic showed a rapid drop with temperature rising, and then decrease in the rate of ILSS became relatively slower; the fiber oxidation had little influence on the ILSS.
基金Project(220636)supported by the Postdoctoral Science Foundation of the Central South University,ChinaProject(2016B090931004)supported by the Guangdong Province Science and Research Plan,ChinaProject(51601229)supported by the National Natural Science Foundation of China。
文摘The high temperature mechanical properties(250 ℃) and microstructure of a die-forged Al-5.87 Zn-2.07 Mg-2.42 Cu alloy after T6 heat treatment were investigated. High temperature tensile tests show that as the temperature increases from room temperature to 250 ℃, the ultimate tensile strength of the alloy decreases from 638 to 304 MPa, and the elongation rises from 13.6% to 20.4%. Transmission electron microscopy(TEM) and electron backscattered diffraction(EBSD) were applied for microstructure characterization, which indicates that the increase of tensile temperature can lead to the coarsening of precipitates, drop of dislocation density, and increase of dynamic recovery. After tensile testing at 250 ℃, a sub-grain structure composed of a high fraction of small-angle grain boundary is formed.
文摘The tensile equipment of the advanced confocal scanning laser microscope (CSLM) was used to research the high temperature mechanical properties of low carbon silicon-bearing steel by twin-roll strip casting. The results show that, at the strain rate of 0. 000 5 s ^-1, the strip clearly shows signs of brittleness at around 600 ℃ and its plasticity falls considerably between 750 ℃ and 600 ℃. This is because during the transformation from austenite to ferrite, the low strength ferrite at the austenite grain boundaries greatly reduces the steel' s high temperature plasticity. The subsequent strip coiling process should be controlled at less than the brittle temperature of approximately 600 ℃, so cracks at the coiling stage can be prevented.
基金support from the National Key Technology Research and Development Program of China (No.2007BAE38B06)Heilongjiang Province Science Fund for Distinguished Young Scholars(No. JC201013)
文摘The elevated temperature performances of 2D70 Al alloy hot extrusion rods after two-stage homogenization and intensive deformation were studied by measuring the elevated temperature enduring strength and the creep ultimate strength. The fracture morphology of some selected samples after testing at different elevated temperatures was observed by scanning electron microscopy (SEM). The results indicate that, as the test temperature increases, the elevated temperature enduring strength of 2D70 Al alloy decreases gradually. In a comparison between 150 C and 240 C, the notch enduring strength drops from 375 to 185 MPa and the smooth enduring strength drops from 337 to 130 MPa. Enduring strength is not sensitive to the notch. The notch sensitivity ratio (NSR) coefficient is in the range of 1.119 to 1.423 from 150 C to 240 C. The creep test results show that, as the test temperature increases from 150 C to 240 C, the creep ultimate strength of 2D70 Al alloy rods drops gradually from 312 to 117 MPa.
基金financially supported by the National Natural Sciences Foundation of China(Grant No.51171119 and No.51401129)
文摘The high temperature tensile and fracture behavior of Zr50Al40Cu10 metallic glass at the temperature range in the vicinity of glass transition were investigated. Tensile tests were carried out at room temperature, 350-420 ℃, and in the supercooled liquid region temperature range, respectively. Obvious plastic deformation was initiated at temperature about 80 °C lower than the glass transition temperature. The ultimate tensile strength decreases with the increase of testing temperature and the ductility increases with temperature. At temperature higher than Tg, viscous flow of Non-Newtonian fluid led to super plastic deformation behavior. The deformation process under tension was inhomogeneous, and remarkable serrations were observed on the stress-strain curve near glass transition temperature.
文摘Self-reinforced Si_3N_4 ceramics containing high oxynitride glass have been fabricated by the control of microstructure evolution and β-Si_3N_4 grain growth. The effects of the size distribution of the elongated β-SiaN_4 grains, and the β-Si_3N_4 grain growth as well as the oxynitride glass chemical characteristic on the microstructure and mechanical properties were investigated. The experimental results show that the β-Si_3N_4 grains in high oxynitride glass grow to elongated rod-like crystals and form the stereo-network structure. Under the sintering conditions of 1800℃ and 60 min, a quite uniform microstructure with an average aspect ratio of 6.5 and an average of 1 μm can be obtained. A large amount of oxynitride glass phase with high nitrogen content enhances the elevated temperature fracture toughness because of its high softening temperature and high viscosity. In the present material, the crack deflection and pullout of the elongated rod-like β-Si_3N_4 grains are the primary toughening mechanisms.