Charging System of ECRH High-Voltage Power Supply and its Control System

High-voltage power supply (HVPS) of Electron Cyclotron Resonance Heating (ECRH) for HT-7 and HT-7U is presently being constructed. The high voltage (100 kV) energy of HVPS is stored in the capacitor banks, and they can power one or two gyrotrons. All the operation of the charging system will be done by the control system, where the field signals are interfaced to programmable logic controller (PLC). The use of PLC not only simplifies the control system, but also enhances the reliability. The software written by using configuration software installed in the master computer allows for remote and multiple operator control, and the status and data information is also remotely available.

Design and control of the accelerator grid power supply-conversion system applied to CFETR N-NBI prototype

The acceleration grid power supply(AGPS)rated 200 kV/25 A is a key component devoted to supply the acceleration grids of the China fusion engineering test reactor negative-ion-based neutral beam injector(N-NBI)prototype system.This paper focused on the design and control of the AGPS conversion system(AGPS-CS),with emphasis on the requirement of the wide range output voltage and rise time.A voltage regulation switch at the front of step-down transformer is applied to optimize the grid current and DC-link voltage.Moreover,a new feedforward control strategy with piecewise PI compensator is proposed to improve the characteristics of AGPS.The simulation results of the proposed AGPS-CS are presented,proving the performance of the power supply to achieve the desired requirements.

The Design of PSM-Based ECRH Power Supply Control System

Electron cyclotron resonance heating (ECRH) system is one of the most important Tokamak auxiliary heating methods. However, there are growing demands for ECRH system as the physical experiments progress which meanwhile adds the difficulty of designing and building the control system of its power source. In this paper, the method of designing a control system based on Single Chip Microcomputer (SCM) and Field Programmable Gate Array (FPGA) is introduced according to its main requirements. The experimental results show that the control system in this paper achieves the conversion of different working modes, gets exact timing, and realizes the failure protection in 10us thus can be used in the ECRH system.

Experiment and Operation of a LHCD-35kV/2.8MW/1000s High-Voltage Power Supply on HT-7 Tokamak

A -35 kV/2.8 MW/1000s high-voltage power supply (HVPS) for HT-7 superconducting tokamak has been built successfully. The HVPS is scheduled to run on a 2.45 GHz/1 MW lower hybrid current drive (LHCD) [1] system of HT-7 superconducting tokamak before the set-up of HT-7 superconducting tokamak in 2003. The HVPS has a series of advantages such as good steady and dynamic response, logical computer program controlling the HVPS without any fault, operational panel and experimental board for data acquisition, which both are grounded distinctively in a normative way to protect the main body of HVPS along with its attached equipments from dangers. Electric power cables and other control cables are disposed reasonably, to prevent signals from magnetic interference and ensure the precision of signal transfer.This paper involves the experiment and operation of a 35 kV/2.8 MW/1000s HVPS [2] for 2.45 GHz/1 MW LHCD system. The reliability and feasibility of the HVPS has been demonstrated in comparison with experimental results of original design and simulation data.

Inverter power supply system for high-power twin-wire pulsed GMAW

A type of novel inverter power supply system for high-power twin-wire pulsed gas metal arc welding （GMAW） is presented mainly for dealing with the disadvantages of the conventional power supply for twin-wire pulsed GMA W of which the output power is generally difficult to increase due to limitations of the power of semiconductors and the power density of magnetic devices. In the power supplies for the master and slave arcs, the digital signal processor （DSP） TMS320F28335 is used to form the DSP- based synergic control system for parallel high-power pulsed GMA W, which achieves high-power output of two parallel inverters controlled by a single DSP ; master-slave communication is achieved by using e controller area network （eCAN）module of DSP, thas realizing anti-phase pulse output of high-power twin-wire pulsed GMA W and reducing the interference between twin arcs. The experiment results demonstrate that the designed inverter power supply system for high-power twin-wire pulsed GMAW can bring about high-power efficiency of welding, stable welding process and proper formation of welds.

Design and Simulation of a Electrorheological(ER) Control High Voltage Power Supply

Few applications with electrorheological （ER） fluids have been found in industry. One reason is high voltage power supplies cannot meet the requirement for ER effect. In this paper, an ER control high voltage power supply for engineering application was designed which reduced power wastage by adopting soft switch technology; lessened its volume to satisfy micromation when adopting the planar transformer and improved its response character- istic by choosing an assistant discharging circuit. Simultaneously, a simulation analysis has been carried out. As results, the output voltage of this high voltage power supply is 5 kV, and the voltage can be continuously regulated and the voltage ripple is only 0. 7 %, so the requirement of stability is also achieved.

Application of High-Voltage Power Supply on Electrostatic Precipitator

This article firstly describes the main technical parameters and performance of the high power supply of electrostatic precipitator, and then describes the structure, principle and characteristic of power supply of electrostatic precipitator, and finally analyses the common faults of power supply of electrostatic precipitator in the operation and puts forward the methods of dealing with breakdown. Operation results show that the system is stable and reliable, and overall performance and the efficiency of dust control have been improved significantly. The scheme has been well applied in the field of environmental protection and dust removal.

Design of Power Supply for On-line Monitoring System of Transmission Lines

This paper uses CT to gain the energy directly from the high-voltage transmission line, to address the problem of power supply for monitoring system in high voltage side of transmission line. The draw-out power coil can induce voltage from the transmission line, using single-chip microcomputer to analog and output PMW wave to control the charging module, provides a stable 3.4 V DC voltage to the load, and solve the problem of easy saturating of core. The power supply based on this kind of draw-out power coil has undergone the overall testing, and it is verified-showing that it can properly work in a non-saturated status within the current range of 50 - 1000 A, and provide a stable output. The equipment also design protection circuit to improve the reliability to avid the impacts of the impulse current or short-circuit current. It effectively solves the problem of power supply for On-line Monitoring System of Transmission.

The Power Supply System for HL-2A Tokamak's Magnetic Field

The highpower pulsed power supply system for the magnetic field of the HL-2A Tokamak is described in this paper. The total output power of its eight magnetic field power supply units of nearly 250 MW. Their highest DC output voltage and current are 3510 V and 45 kA, respectively. All the units are operated in a pulsed mode. The pulse duration is 5 s, and the cyclic period is 15 min. The power supply system consists mainly of pulsed flywheel motor generators, rectifying transformers, thyristor converters, diode rectifiers and switches. The system incorporates many key technologies-supply equalization with two generators and four diode bridges, constant-angle phase triggers with a wide frequency range, current equalization, a status detector for the high current 6-phase converter, and advanced monitoring based on a programmable logic computer and engineering parameter measurement. The experimental results show that the performance of the power supply system satisfies the requirements of HL-2A experiments very well.

High-power High-efficient and Simplified High-frequency Switching Power Supply for Electrolytic Plating

针对大功率电解电镀开关电源的输入整流级引起的无功和谐波等电能质量问题,研究了一种基于高效PWM整流的高频开关电源。该电源前级整流器仅用4个开关管来进行PWM整流,后级采用半桥逆变器进行高频变换,显著减少了开关数量。针对三相四开关PWM整流器,推导一种基于开关模型的无差拍控制方法,该方法可实现系统的快速、无差整流。针对多台开关电源的并联均流问题,提出一种基于虚拟阻抗的自均流控制方法,可实现多台电源的均流稳定运行。通过仿真与实验验证了所提结构和控制方法的正确性。

Programmable Voltage Regulating Method for 15 kV High Voltage DC Power Supply

In order to solve the disadvantages caused by mechanical slide rheostat that has big errors and low precision,a novel voltage regulation method for high voltage DC power supply was introduced.The key of this method were digital potentiometer MAXIM 5455 and linear photoelectric coupling LOC110,and application programs were compiled using Visual Basic which was graphical compiling language,furthermore the communication between exterior and computer was carried out by ICP7044D module,in consequence the output value of high voltage DC power supply could be regulated with computer.The measured results showed that this method could accurately,conveniently and rapidly regulate the output value of high voltage DC power supply.

Optical fiber-based power and data delivery system for high voltage electronic current transformer

This paper describes a prototype power delivery system developed for high voltage electronic current transformer （ECT） that uses laser light to transfer power to and communicates with the primary converter. The design is based on optical-to-electrical power converters, solid-state diode lasers and optical fibers. Command signals are transmitted via the same up-fiber used to send power from secondary power supply to primary converter. The upward data transmission is completed during the brief interruption of power delivery without affecting steady power-supply. A simple comparator added to the primary converter can take the command data. Experimental results show that the fibers can provide reliable up-link for data transmission at 200 kb/s from the secondary to the primary converter. Based on the delivery system, the secondary converter can control three auxiliary channels to provide additional information. These monitoring channels are used in a time-multiplexing mode to provide information about the operation temperature, voltage and current at the remote unit for monitoring the ECT. This preventive maintenance or built-in test can increase reliability by giving early warning for necessary maintenance request.

A Study on the Conducted Interference of Capacitor Charging Power Supply

In this paper, a mathematical analysis of the EMI (Electromagnetic Interference) for a 20 kHz/10 kV capacitor charging power supply in frequency-domain is presented, and a related circuit model considering the transient switching interference is proposed. Due to the high working frequency and the device-switching transitions, the conducted EMI caused by the charging circuit which includes the harmonics of grid frequency, working frequency and device-switching transition frequencies. Thus under certain working situations or loads parallel power supply, the interference may cause charging failure. To solve this problem, a high frequency transformer modeled with stray capacitances and an approximation of the device-switching transition is applied in the Spice-based simulation model, and a mathematical analysis in frequency-domain is presented.

A Novel Half-Bridge Power Supply for High Speed Drilling Electrical Discharge Machining

High Speed Drilling Electrical Discharge Machining (HSDEDM) uses controlled electric sparks to erode the metal in a work-piece. Through the years, HSDEDM process has widely been used in high speed drilling and in manufacturing large aspect ratio holes for hard-to-machine material. The power supplies of HSDEDM providing high power applica-tions can have different topologies. In this paper, a novel Pulsed-Width-Modulated (PWM) half-bridge HSDEDM power supply that achieves Zero-Voltage-Switching (ZVS) for switches and Zero-Current-Switching (ZCS) for the dis-charge gap has been developed. This power supply has excellent features that include minimal component count and inherent protection under short circuit conditions. This topology has an energy conservation feature and removes the need for output bulk capacitors and resistances. Energy used in the erosion process will be controlled by the switched IGBTs in the half-bridge network and be transferred to the gap between the tool and work-piece. The relative tool wear and machining speed of our proposed topology have been compared with that of a normal power supply with current limiting resistances.

Protection Schemes for Uniline Zone in Bilateral AT Traction Power Supply System

With the rapid development of the construction of high-speed railway in china, higher levels of power quality and reliability of traction power supply systems are required.The combination of bilateral power supply technology with AT traction power supply technology can better meet the needs of development of high-speed railways, which will require new protection approaches to be proposed. Thus, corresponding protection schemes will be of great significance for the application and promotion of bilateral power supply technology.

Analysis on the Situation of Power Supply and Demand in Shandong

In the first half of 2007, the power industry in Shandongprovince continued to maintain a rapid growth momentum.The gross electricity consumption amounted to 121.25 TWh,14.4% higher over that in the same period of last year. The totalinstalled capacity reached 53.29 GW. It was expected that bythe end of 2007, the gross electricity consumption in Shan-dong would reach 260 TWh, increasing by 14.4% on ayear-on-year basis; the maximum load would reach 40.

Investigation on latch-up susceptibility induced by high-power microwave in complementary metal–oxide–semiconductor inverter

The latch-up effect induced by high-power microwave（HPM） in complementary metal–oxide–semiconductor（CMOS） inverter is investigated in simulation and theory in this paper. The physical mechanisms of excess carrier injection and HPM-induced latch-up are proposed. Analysis on upset characteristic under pulsed wave reveals increasing susceptibility under shorter-width pulsed wave which satisfies experimental data, and the dependence of upset threshold on pulse repetitive frequency（PRF） is believed to be due to the accumulation of excess carriers. Moreover, the trend that HPMinduced latch-up is more likely to happen in shallow-well device is proposed.Finally, the process of self-recovery which is ever-reported in experiment with its correlation with supply voltage and power level is elaborated, and the conclusions are consistent with reported experimental results.

High Proportion Renewable Energy Supply and Demand Structure Model and Grid Impaction

In considering of high proportion of renewable energy supply in 2050, the accelerating of energy consumption gross, source and environment can affect the energy system restrict affection are stronger. Add wind and solar to electricity energy with large amount of energy source exploitation. The energy source amount per person is lower. Considering the renewable energy amount and supply, primary energy storage and structure problem is standing out. Before the wide spread of renewable energy, Using the high-carbon energy in China can pollute seriously. Chinese energy supply and demand problem is research key point. This paper researches Chinese energy supply and demand pattern system and evaluation methodology, gives out the inner and outer influencing elements. And evaluate Chinese energy supply and demand pattern from energy gross, structure, distribution and transportation. Use energy supply synthesize radar comparison chart in certain time period. From energy security, economy, clean and efficiency, analyze the benefit comparisons of Chinese energy supply and demand pattern. This energy supply and demand pattern model will give one certain theoretical analysis and practice reference to the further high proportion of renewable energy.

一种高效星载功率调节与配电单元设计与实现

文章结合深空探测供配电分系统任务特点,提出功率调节、配电、火工控制等多功能模块轻小型一体化设计的必要性。介绍了国外功率调节与配电单元的研究现状、国产功率调节与配电单元研制的意义,功率调节与配电单元组成及功能设计,并通过多母线融合设计、多路放电均流设计、单元集成化设计等关键技术,解决了深空探测器高可靠轻小型化功率调节与配电单元设计难题。在轨飞行结果表明:功率调节与配电单元功能正常,工作可靠,性能优良。功率调节与配电单元的国产化设计实现,可为其它航天器的设计提供参考和借鉴。