Mechanics Behavior of Ultra High Toughness Cementitious Composites after Freezing and Thawing

Mechanical behaviors of UHTCC after freezing and thawing were investigated,and compared with those of steel fiber reinforced concrete（SFRC）,air-entrained concrete（AEC） and ordinary concrete（OC）.Four point bending tests had been applied after different freezing-thawing cycles（0,50,100,150,200 and 300 cycles,respectively）.The results showed that residual flexural strength of UHTCC after 300 freezing-thawing cycles was 10.62 MPa（70% of no freezing thawing ones）,while 1.58 MPa（17% of no freezing thawing ones） for SFRC.Flexural toughness of UHTCC decreased by 17%,while 70% for SFRC comparatively.It has been demonstrated experimentally that UHTCC without any air-entraining agent could resist freezing-thawing and retain its high toughness characteristic in cold environment.Consequently,UHTCC could be put into practice for new-built or retrofit of infrastructures in cold regions.

Flexural response of reinforced concrete beams strengthened with post-poured ultra high toughness cementitious composites layer

Four-point bending tests were conducted up to failure on eleven reinforced concrete (RC) beams and strengthening beams to study the effectiveness of externally pouring ultra high toughness cementitious composites (UHTCC) on improving the flexural behavior of existing RC beams.The strengthening materials included UHTCC and high strength grade concrete.The parameters,such as thickness and length of strengthening layer and reinforcement in post-poured layer,were analyzed.The flexural behavior,failure mode and crack propagation of composite beams were investigated.The test results show that the strengthening layer improves the cracking and ultimate load by increasing the cross section area.Introducing UHTCC material into strengthening not only improves the bearing capacity of the original specimens,but also disperses larger cracks in upper concrete into multiple tightly-spaced fine cracks,thus prolonging the appearance of harm surface cracks and increasing the durability of existing structures.Compared with post-poured concrete,UHTCC is more suitable for working together with reinforcement.The load?deflection plots obtained from three-dimensional finite-element model (FEM) analyses are compared with those obtained from the experimental results,and show close correlation.

Uniaxial Compressive Properties of Ultra High Toughness Cementitious Composite

Uniaxial compression tests were conducted to characterize the main compressive performance of ultra high toughness cementitious composite （UHTCC） in terms of strength and toughness and to obtain its stress-strain relationships. The compressive strength investigated ranges from 30 MPa to 60 MPa. Complete stress-strain curves were directly obtained, and the strength indexes, including uniaxial compressive strength, compressive strain at peak stress, elastic modulus and Poisson＇s ratio, were calculated. The comparisons between UHTCC and matrix were also carried out to understand the fiber effect on the compressive strength indexes. Three dimensionless toughness indexes were calculated, which either represent its relative improvement in energy absorption capacity because of fiber addition or provide an indication of its behavior relative to a rigid-plastic material. Moreover, two new toughness indexes, which were named as post-crack deformation energy and equivalent compressive strength, were proposed and calculated with the aim at linking up the compressive toughness of UHTCC with the existing design concept of concrete. The failure mode was also given. The study production provides material characteristics for the practical engineering application of UHTCC.

Mechanical properties and grain refinement by acicular ferrite in high strength high toughness weld metal

The volume fraction and morphology of acicular ferrite evolution in a high strength high toughness weld metal were studied and the mechanical properties of weld metal under heat input of 21 kJ/cm with and without fast cooling were tested. The results show the weld metal can obtain a large proportion of acicular ferrite during a wide range of cooling rate and the sizes of acicular ferrite in length and thickness decrease with cooling rate increasing. The weld metal exhibited high tensile strength （895 MPa and 870 MPa） and good low temperature toughness （average AKv-30℃ 104 J and 79. 2 J）. The higher tensile strength and better low temperature toughness of the weld metal under fast cooling are due to the more refined grain of acicular ferrite.

Fabrication of High Toughness Silk Fibroin/Tungsten Disulfide Nanoparticles Hybrid Fiber and Self-Heating Textile by Wet Spinning|

Traditionally,silkworm silk has been used to make high-quality textiles.Nevertheless,various wastes from silk-worm silk textiles that are no longer used are increasing.which is also causing considerable waste and contam-ination.This issue is causing widespread concern in countries that use more silk.Regenerated silk fibroin(RSF)fibers have been shown to be fragile and tender,which prohibits RSF from being widely used as a structural com-ponent.Therefore,enriching the function of silk and enhancing the RSF mechanial properties are important directions to expand the comprehensive utilization of silk products.In the present research,wet spinning was used to create a series of RSF/tungsten disulfide(WS_(2))nanoparticles(NPs)hybrid fiber having distinct WS_(2) nanoparticles concentrations.It was discovered that the temperature of hybrid fibers containing 0.8 wt%RSF/WS_(2) nanoparticles might climb from 20.4℃ to 85.6℃in 1 min and 108.3℃ in 10 min after being exposed to simulated sunlight for a period of one minute and ten minutes.It also had certain antibacterial activity and thermal stability.Fabrics created by hand mixing had outst anding photothermal characteristics under natural sunlight.Further-more,adding WS_(2) nanoparticles might increase the tensile properties of hybrid fibers,which could be caused by the reality that the blending of WS_(2) nanoparticles inhibited the self-assembly of sheets in RSF reaction mixture in a dosage dependent way,as evidenced by the fact that RSF/WSz nanoparticles hybrid fibers had lesser β-sheets material,crystalline nature,and arystalline size.The above performance makes the RSF/WS_(2) nanoparticles hybrid fbers promising candidates for application in photothermal fabrics as well as military dothing.

Constructing high-toughness polyimide binder with robust polarity and ion-conductive mechanisms ensuring long-term operational stability of silicon-based anodes

Silicon-based materials have demonstrated remarkable potential in high-energy-density batteries owing to their high theoretical capacity.However,the significant volume expansion of silicon seriously hinders its utilization as a lithium-ion anode.Herein,a functionalized high-toughness polyimide(PDMI) is synthesized by copolymerizing the 4,4'-Oxydiphthalic anhydride(ODPA) with 4,4'-oxydianiline(ODA),2,3-diaminobenzoic acid(DABA),and 1,3-bis(3-aminopropyl)-tetramethyl disiloxane(DMS).The combination of rigid benzene rings and flexible oxygen groups(-O-) in the PDMI molecular chain via a rigidness/softness coupling mechanism contributes to high toughness.The plentiful polar carboxyl(-COOH) groups establish robust bonding strength.Rapid ionic transport is achieved by incorporating the flexible siloxane segment(Si-O-Si),which imparts high molecular chain motility and augments free volume holes to facilitate lithium-ion transport(9.8 × 10^(-10) cm^(2) s^(-1) vs.16 × 10^(-10) cm^(2) s~(-1)).As expected,the SiO_x@PDMI-1.5 electrode delivers brilliant long-term cycle performance with a remarkable capacity retention of 85% over 500 cycles at 1.3 A g^(-1).The well-designed functionalized polyimide also significantly enhances the electrochemical properties of Si nanoparticles electrode.Meanwhile,the assembled SiO_x@PDMI-1.5/NCM811 full cell delivers a high retention of 80% after 100 cycles.The perspective of the binder design strategy based on polyimide modification delivers a novel path toward high-capacity electrodes for high-energy-density batteries.

Product Development of High Strength and Toughness Spring Flat Steel

With the continuous development of mechanical industry,higher requirements are put forward for the comprehensive properties of spring steel.The chemical composition and production process of spring flat steel are designed to meet the requirements of high strength and high toughness of spring flat steel,through the test,the product surface quality and internal quality all meet the national standards,the performance indicators to meet user requirements.

A dynamic constitutive model of ultra high toughness cementitious composites

In this study,an explicit dynamic constitutive model was established for ultra high toughness cementitious composites(UHTCCs).The model,based on the Holmquist–Johnson–Cook(HJC)model,includes tensile and compressive damage evolution,hydrostatic pressure,strain rate,and the Lode angle effect.The proposed model was embedded in LS-DYNA software and then comprehensive tests were carried on a hexahedral brick element formulation under uniaxial,biaxial,and triaxial stress states to verify its rationality through comparisons with results determined by the HJC and Karagozian&Case(K&C)models.Finally,the proposed model was used to simulate the damage caused to UHTCC targets subjected to blast by embedded explosive and projectile penetration,and predictions were compared with corresponding experimental results.The results of the numerical simulations showed that our proposed model was more accurate than the HJC model in predicting the size of the crater,penetration depth,and the distribution of cracks inside the target following the blast or high-speed impact loading.

Bioinspired laminated bioceramics with high toughness for bone tissue engineering

For the research of biomaterials in bone tissue engineering,it is still a challenge to fabricate bioceramics that overcome brittleness whilemaintaining the great biological performance.Here,inspired by the toughness of naturalmaterials with hierarchical laminated structure,we presented a directional assembly-sintering approach to fabricate laminated MXene/calcium silicate-based(L-M/CS)bioceramics.Benefiting from the orderly laminated structure,the LM/CS bioceramics exhibited significantly enhanced toughness(2.23MPa·m^(1/2))and high flexural strength(145MPa),which were close to the mechanical properties of cortical bone.Furthermore,the L-M/CS bioceramics possessed more suitable degradability than traditional CaSiO_(3)bioceramics due to the newly formed CaTiSiO_(5)after sintering.Moreover,the L-M/CS bioceramics showed good biocompatibility and could stimulate the expression of osteogenesisrelated genes.The mechanism of promoting osteogenic differentiation had been shown to be related to theWnt signaling pathway.This work not only fabricated calciumsilicate-based bioceramics with excellentmechanical and biological properties for bone tissue engineering but also provided a strategy for the combination of bionics and bioceramics.

Development of JG785E High Strength High Toughness Steel Plates

A high strength structure steel plate --brand JG785E, which with more than 690MPa yield strength ,more than 47 joules toughness at minus 40℃ has been developed by Jigang of Shandong Steel Group P. R. China. The steel plates can be easily welded in engineering structure due to its lower carbon equivalent value. The maximum thickness of heavy plate is 50.88mm (2 inch), the yield strength is 710-860MPa, the toughness of steel plate is 139~336J at the temperature of - 40℃ . The microstructure of steel plate is lower carbon Bainite. The main solid dissolve elements are silicon and manganese. All parameters of reheating, rolling and accelerating cooling are controlled strictly. This TMCP procedure can ensure to get better mechanical properties of steel plates, and to keep the market competitive power and lower cost of manufacture. The cleanness of steel is high by refined in ladle furnace (LF), the contents of P and S is lower. It is the low carbon Bainite microstructure that possesses the high strength, excellent lower temperature toughness and better weld-ability without preheat process. The JG785E is typical brand of the Jigang’s high strength steel brands as the S690QL conforms to EN10025-6 and as the ASTM A514M conforms to USA quenching and tempering steel specification.

Dynamic fracture toughness of high strength metals under impact loading:increase or decrease

An elusive phenomenon is observed in previous investigations on dynamic fracture that the dynamic fracture toughness （DFT） of high strength metals always increases with the loading rate on the order of TPa.m1/2.s-1. For the purpose of verification, variation of DFT with the loading rate for two high strength steels commonly used in the aviation industry, 30CrMnSiA and 40Cr, is studied in this work. Results of the experiments are compared, which were conducted on the modified split Hopkinson pressure bar （SHPB） apparatus, with striker velocities ranging from 9.2 to 24.1 m/s and a constant value of 16.3 m/s for 30CrMnSiA and 40Cr, respectively. It is observed that for 30CrMnSiA, the crack tip loading rate increases with the increase of the striker velocity, while the fracture initiation time and the DFT simultaneously decrease. However, in the tests of 40Cr, there is also an increasing tendency of DFT, similar to other reports. Through an in-depth investigation on the relationship between the dynamic stress intensity factor （DSIF） and the loading rate, it is concluded that the generally increasing tendency in previous studies could be false, which is induced from a limited striker velocity domain and the errors existing in the experimental and numerical processes. To disclose the real dependency of DFT on the loading rate, experimentsneed to be performed in a comparatively large striker velocity range.

A New Method for Determining J_(IC) of High StrengthHigh Fracture Toughness Steels by SingleThree Point Bend Specimen

A single three point bend specimen compliance method for determining JIC of high strength high fracture toughness steels is presented and a formula for calculatinff J-integral is proposed as follows.It is simple and valid for high strength high fracture toughness steels. The values of JIC and KIC measured by this method are in good agreement with those measured by standard test method.

Effect of W on microstructure of high strength and toughness steels

The effect of W on the microstructure and the mechanical properties of ultrahigh strength low alloy steels was carried out. The microstructure of 30Cr3Si2Mn2NiMoNb and 30Cr3Si2Mn2NiMoNbW steels under quenched conditions were investigated by metallographic microscope, scanning electron microscope （SEM）, X-ray diffrac- tion （XRD）, and transmission electron microscope （TEM）. Thermodynamic cal- culation was also conducted. The results showed that the addition of W made undissolved carbides more and finer, which exerted strong pinning force on migrat- ing packet boundary and improved tensile strength significantly. M6C particles in 30Cr3Si2Mn2NiMoNb steel were disappeared above 1193 K, while the M6C particles in 30Cr3Si2Mn2NiMoNbW steel were disappeared above 1253 K, the calculation results were in agreement with the experimental.

Development of High Strength and Toughness Non-Heated Al–Mg–Si Alloys for High-Pressure Die-Casting

Based on the 3 factors and 3 levels orthogonal experiment method,compositional effects of Mg,Si,and Ti addition on the microstructures,tensile properties,and fracture behaviors of the high-pressure die-casting Al-x Mg-y Si-z Ti alloys have been investigated.The analysis of variance shows that both Mg and Si apparently infl uence the tensile properties of the alloys,while Ti does not.The tensile mechanical properties are comprehensively infl uenced by the amount of eutectic phase(α-Al+Mg2Si),the average grain size,and the content of Mg dissolved intoα-Al matrix.The optimized alloy is Al-7.49 Mg-3.08 Si-0.01 Ti(wt%),which exhibits tensile yield strength of 219 MPa,ultimate tensile strength of 401 MPa,and elongation of 10.5%.Furthermore,contour maps,showing the relationship among compositions,microstructure characteristics,and the tensile properties are constructed,which provide guidelines for developing high strength and toughness Al–Mg–Si–Ti alloys for high-pressure die-casting.

Design principles in mechanically adaptable biomaterials for repairing annulus fibrosus rupture:A review

Annulus fibrosus(AF)plays a crucial role in the biomechanical loading of intervertebral disc(IVD).AF is difficult to self-heal when the annulus tears develop,because AF has a unique intricate structure and biologic milieu in vivo.Tissue engineering is promising for repairing AF rupture,but construction of suitable mechanical matching devices or scaffolds is still a grand challenge.To deeply know the varied forces involved in the movement of the native annulus is highly beneficial for designing biomimetic scaffolds to recreate the AF function.In this review,we overview six freedom degrees of forces and adhesion strength on AF tissue.Then,we summarize the mechanical modalities to simulate related forces on AF and to assess the characteristics of biomaterials.We finally outline some current advanced techniques to develop mechanically adaptable biomaterials for AF rupture repair.

Molecular movements of trehalose inside a single network enabling a rapidly-recoverable tough hydrogel

It remains a challenge to achieve rapidly recoverable hydrogels by molecular hydrogen-bonding interaction because of its slow inter-action kinetics.This work for the first time reports a trehalose(Tre)-based molecular movement mechanism inside a single network of polyacrylamide(PAM)that accelerates the kinetics of hydrogenbonding interaction,and thereby endows the hydrogel with high toughness and rapid shape and mechanical recoverability.The resultant PAM@Tre hydrogel is capable of full shape recovery after 10,000 loading/unloading cycles at a strain of 500%.Even after being stretched at a strain of 2500%,it can recover to its original shape within 10 seconds.Moreover,the molecular movement of trehalose also endows the PAM@Tre hydrogel with fracture energy and toughness as high as~9000 J m^(-2) and~1600 kJ m^(-3),respec-tively,leading to strong resistance to both static and dynamic piercing.The PAM@Tre hydrogel is thus believed to have enormous potentials in protection devices,bionic skin,soft actuator,and stretchable electronics.