High-temperature tribological properties of Ni-P alloy coatings deposited by electro-brush plating

High-temperature tribological properties of Ni-P alloy coatings processed by electro-brush plating on 20CrMo steel have been investigated. A baU-on-disc configuration was employed and 4 mm diameter Si3N4 balls were used as static counterpart. All the wear tests were carried out at 450℃ for 180 rain without lubricants. The electro-brush plating Ni-P coating is amorphous in as-deposited condition, and it becomes polycrystalline with the formation of Ni and Ni3P after heat treatment at 450℃for 1 h. The friction coefficient of the Ni-P coating is just 50% of that of the 20CrMo steel at the friction temperature of 450℃. A mild adhesive wear mechanism was found for the electro-brush plating Ni-P coating tested at 450℃, whereas for the 20CrMo steel at the same temperature a mixed adhesive and abrasive wear mechanism was observed.

High-temperature frictional wear behavior of MCrAlY-based coatings deposited by atmosphere plasma spraying

Al2O3-r2O03/NiCoCrAIYTa coatings were prepared via atmosphere plasma spraying （APS）. The microstructure and phase com- position of the coatings were analyzed by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, laser confocal scanning microsco- py （LSCM）, and transmission electron microscopy （TEM）. The dry frictional wear behavior of the coatings at 500℃ in static air was inves- tigated and compared with that of 0Cr25Ni20 steel. The results show that the coatings comprise the slatted layers of oxide phases, unmelted particles, and pores. The hot abrasive resistance of the coatings is enhanced compared to that of 0Cr25Ni20, and their mass loss is approxi- mately one-fifteenth that of 0Cr25Ni20 steel. The main wear failure mechanisms of the coatings are abrasive wear, fatigue wear, and adhe- sive wear.

Evaluation of Oxidation of Ti-Al and Ti-Al-Cr Coatings Arc-ion Plated on Ti-60 High-temperature Titanium Alloy

High-temperature titanium alloy for aeroengine compressor applications suffers from high-temperature oxidation and environmental corrosion, which prohibits long-term service of this kind alloy at temperatures above 600℃. In an attempt to tackle this problem, Ti-48Al （at. pct） and Ti-48Al-12Cr （at. pct） protective coatings were plated on the substrate of alloy Ti-60 by arc ion plating （ALP） method. Isothermal and cyclic oxidation tests were performed in static air at elevated temperatures. Phase composition, morphology of the coatings and distribution of elements were investigated by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and energy dispersive X-ray analysis （EDX）. The results showed that the Ti-48Al coating exhibited good isothermal oxidation resistance during exposure at 800℃, but poorer resistance against oxidation at 900℃. By contrast Ti-48Al-12Cr coating demonstrated excellent isothermal oxidation resistance at both temperatures. Cyclic oxidation tests performed at 800℃ indicated that resistance and no spallation of coatings was observed. But both coatings demonstrated good cyclic oxidation at 900℃ only Ti-48Al-12Cr coating demonstrated excellent cyclic oxidation resistance.

Microstructure of nanometer Al_2O_3 dispersion strengthened Ni-based high-temperature protective coatings by laser cladding

The nanometer Al2O3 dispersion strengthened NiCoCrAlY high-temperature protective coatings by crosscurrent CO2 laser on Ni-based superalloy GH4033 were produced. Microscopic morphologies, phase constitutions of cladding coatings and distribution of nano-Al2O3 particles were examined using SEM and XRD. The results show that the interface grains, after adding proper nano-Al2O3, grow from epitaxial to non-epitaxial shape gradually, and the columnar dendrites become thinner and denser with cellular shape. Cracks in the substrate close to the interface are eliminated. Moreover, dispersive nano-Al2O3 particles mainly distribute around cellular substructure and on grain-boundaries, which prevents the diffusion of alloying elements and restrains the formation of new phase. There is a critical value of nano-Al2O3 addition, and the most suitable content of nano-Al2O3 is 1% (mass fraction) in this experimental conditions. The "nanometer effect" of nano-Al2O3 particles plays an important role in the improvement of coating microstructure.

High-temperature protective coatings on superalloys

Protective coatings are essential for superalloys to serve as blades of gas turbines at high temperatures, and they primarily include aluminide coating, MCrAlY overlay coating, thermal barrier coating and microcrystalline coating. In this paper, all these high temperature coatings are reviewed as well as their preparing techniques. Based on the most application and the main failure way, the importance is then presented for further deepgoing study on the high temperature oxidation law of aluminide coatings.

Microstructure studies of air-plasma-spray-deposited CoNiCrAlY coatings before and after thermal cyclic loading for high-temperature application

In the present study, bond-coats for thermal barrier coatings were deposited via air plasma spraying（APS） techniques onto Inconel 800 and Hastelloy C-276 alloy substrates. Scanning electron microscopy（SEM）, transmission electron microscopy（TEM）, X-ray diffraction（XRD）, and atomic force microscopy（AFM） were used to investigate the phases and microstructure of the as-sprayed, APS-deposited Co Ni Cr Al Y bond-coatings. The aim of this work was to study the suitability of the bond-coat materials for high temperature applications. Confirmation of nanoscale grains of the γ/γ′-phase was obtained by TEM, high-resolution TEM, and AFM. We concluded that these changes result from the plastic deformation of the bond-coat during the deposition, resulting in Co Ni Cr Al Y bond-coatings with excellent thermal cyclic resistance suitable for use in high-temperature applications. Cyclic oxidative stability was observed to also depend on the underlying metallic alloy substrate.

High-temperature Oxidation Resistant Coatings Composed of YSZ Particles Packaged by Nano-Al_2O_3 Film

The alloy performance to resist high-temperature oxidation is mainly determined either by the formation of oxide scales or by the deposition of oxide coatings on the surface of alloys.In the former case,a protective oxide scale,such as Al_2O_3,Cr_2O_3 and SiO_2,can be selectively formed by adjusting the composition of alloys.Even if the oxide scale on the surface of alloys is spalled,new oxide can grow continuously,so the oxidation of alloys can be inhibited effectively.In the latter case,theoretically, depositing oxygen diffusion barrier oxide coatings,such as Al_2O_3,Cr_2O_3 and SiO_2,can prevent alloys from oxidation as well.However,the integrity of these oxide coatings can not maintain for a long time,owing to the thermal stress produced by the difference of the expansion coefficients between the oxide coatings and alloy substrates.Consequently,the ability to resist high-temperature oxidation by depositing such oxide coatings should be disappeared.Therefore,an oxide coating possessed both properties to act as an excellent oxygen diffusion barrier and match a suitable expansion coefficient with alloy substrate,is the basic conditions for the coating to maintain the ability to resist high-temperature oxidation of alloys. Based on above-mentioned idea,a novel composite oxide coating has been developed to obtain two kinds of functions,to act as an oxygen diffusion barrier and to adjust the expansion coefficient of coating as required.Figure 1 shows the schematic diagram of such novel oxide coating.This coating is composed of ZrO_2-8%Y_2O_3(YSZ) particles packaged by nano-Al_2O_3 film.The nano-Al_2O_3 film has a bubble-like structure,each YSZ particle is packaged in an Al_2O_3 bubble.Owing to YSZ is a good conductor for oxygen ions,so oxygen diffusion in this composite coating is determined by the walls of Al_2O_3 bubbles or the nano-Al_2O_3 film.If the thickness of all walls of Al_2O_3 bubbles in the direction perpendicular to the surface of alloy is over a critical value,the Al_2O_3 bubbles can act as an excellent oxygen diffusion barrier. Owing to YSZ has a high thermal expansion coefficient,so the thermal expansion coefficient of coatings can be easily increased by enhancing the ratio of YSZ to Al_2O_3 in these coatings. These composite coatings have been prepared by an improved sol-gel method.Firstly, YSZ particles packaged Al_2O_3 gel film were painted or deposited by electrophoresis on the alloy surface. Then,the specimens were treated by thermal pressure filtration to get primary coatings without cracks.Finally,the primary coatings were sintered in microwave furnace to obtain compact coatings. It is demonstrated from the result of cycling oxidation experiment that both of the hightemperature oxidation resistance and oxide spallation resistance are increased obviously with the ratio of YSZ to Al_2O_3 in the coatings,which are much superior to that of MCrAlY coatings.Therefore, these novel coatings can be used to protect various kinds of alloys from high-temperature oxidation,and can be also served as the interlayer in the thermal barrier coating system.

Microstructure and high temperature oxidation resistance of Si-Y co-deposition coatings prepared on TiAl alloy by pack cementation process

In order to improve the high temperature oxidation resistance of TiAl alloy, Y modified silicide coatings were prepared by pack cementation process at 1030, 1080 and 1130 °C, respectively, for 5 h. The microstructures, phase constitutions and oxidation behavior of these coatings were studied. The results show that the coating prepared by co-depositing Si?Y at 1080 °C for 5 h has a multiple layer structure: a superficial zone consisting of Al-rich (Ti,Nb)5Si4 and (Ti,Nb)5Si3, an out layer consisting of (Ti,Nb)Si2, a middle layer consisting of (Ti,Nb)5Si4 and (Ti,Nb)5Si3, and aγ-TiAl inner layer. Co-deposition temperature imposes strong influences on the coating structure. The coating prepared by Si?Y co-depositing at 1080 °C for 5 h shows relatively good oxidation resistance at 1000 °C in air, and the oxidation rate constant of the coating is about two orders of magnitude lower than that of the bare TiAl alloy.

Protective Effect of the Sputtered TiAlCrAg Coating on the High-Temperature Oxidation and Hot Corrosion Resistance of Ti-Al-Nb Alloy

The effect of a sputtered Ti-48AI-8Cr-2Ag (at. pct) coating on the oxidation resistance of the cast Ti-46.5AI-5Nb (at. pct) alloy was investigated in air at 1000-1100℃. Hot corrosion in molten 75 wt pct Na2SO4+25 wt pct K2SO4 was investigated at 900℃. The scale on the cast TiAINb tends to spall in air, while the scale on coating is very adherent. The sputtered Ti-48AI-8Cr-2Ag coating remarkably improved high temperature oxidation resistance of the cast Ti-46.5AI-5Nb alloy because of the formation of an adherent Al2O3 scale. Due to the inward diffusion of Cr, Kirkendall voids were found at the coating/substrate interface. TiAICrAg coating provided excellent hot corrosion resistance for TiAINb alloy in molten 75 wt pct Na2SO4+25 wt pct K2S04 at 900℃ due to the formation of a continuous Al_2O_3 scale.

High-temperature Compressive Performance of Mg Alloy Foams Coated with Ni-P Layer

Mg/Ni hybrid foams were fabricated by the electroless method.The Ni-P(Nickel-Phosphorous)coatings were deposited on the surface of closed-cell Mg alloy foams.The composition,microstructure and phases of the Ni-P coatings were characterized by scanning electron microscopy(SEM),energy-dispersive X-ray spectroscopy(EDS)and X-ray diffraction(XRD),respectively.The compressive tests were performed on the Mg/Ni hybrid foams at 400℃using the Mg alloy foams as a reference.The experimental results show that the yield strength,plateau stress and energy absorption capacity of the closed-cell Mg alloy foams at high temperature were improved by the Ni-P coating.And there are four main modes for the Mg/Ni hybrid foam failure at 400℃,i e,shearing in cell wall,bending in cell edge,shedding and cracking in Ni-P coating.

Effect of Al content on high temperature erosion properties of arc-sprayed FeMnCrAl/Cr_3C_2 coatings

Three types of FeMnCrAl/Cr3C2 coatings with different AI content were deposited on 20# steel substrates by the high velocity arc spraying （HVAS） process. Surface microstructures of the coatings were analyzed by optical microscopy （OM） and X-ray diffractometry （XRD）. High temperature erosion （HTE） tests were performed in an erosion tester at different impact angles. The surface morphologies of the eroded coatings were observed on a field emission scanning electron microscope（FE-SEM）. The laminated structure is found on all the prepared coatings with the porosity and oxide fraction in the coatings decreasing with the Al content from 0 to 15% （mass fraction）. Sample FA3 with 15% Al, possessing the lowest porosity and oxide fraction, has the best HTE resistance, which demonstrates that Al addition can improve the HTE resistance of the coatings. The erosion rate of sample FA1 exhibits a maximum value at 90° impact angle. The maximum erosion rates of both FA2 and FA3 samples appear in the range of 60°-90° impact angles. Erosion loss of the coatings occurs through brittle breaking, cutting and fatigue spalling.

Fabrication of high temperature grating on thermal barrier coatings based on solute-solvent separation soft lithography

In this study, an etched-SiO-film grating fabrication technique based on solute-solvent separation soft lithography is developed. By using this new technique, high temperature grating with frequency of 600 lines/mm is successfully fabricated on the surface of thermal barrier coatings(TBCs). During the fabrication process, the microstructure and chemical compositions of ceramic coating before and after polishing is analyzed with a digital microscope and the energy dispersive X-ray spectroscope(EDS) in scanning electron microscope(SEM). And then the grating on TBCs is heated at the temperature ranging from 300℃ to 1000℃ for examining the high temperature resistance. In the practical application, the displacement and strain field around the crack on the ceramic surface are investigated with geometry phase analysis(GPA). The successful results verify that the etched-SiO-film grating has a good oxidation resistance and can be applied to high temperature deformation measurement of TBCs.

High temperature performance of arc-sprayed aluminum bronze coatings for steel

The high-temperature oxidation behavior of arc-sprayed aluminum bronze coatings on steel substrate was studied during isothermal exposures in air at 900 ℃. The surface morphologies and interface of the coatings after isothermal oxidation at 900 ℃ for different times were observed. The experiments showed that the coatings on steel substrate were not deteriorated and the substrate was protected well, being exposed to high temperatures up to 900 ℃ . The coatings withstood more than ten times thermal shock tests without any coating separation. The thermal expansion coefficient of the coatings was measured, revealing not much difference between it and that of steel substrate. After exposure at high temperature, the coatings were still adhered to steel substrate well. Isothermal mass gain of the coatings at elevated temperature in dry air was measured by means of a thermal balance and the oxidation behavior was evaluated by oxidation kinetic curves, exhibiting the oxidation kinetics curve accorded with a parabolic law. The parabolic rate constant of the oxidation kinetic curve is 1.02×10?9 g2·cm?4·s?1 for the first 60 min and from 150 min to 2 880 min the constant is 5.1×10?12 g2·cm?4·s?1.

Preparation of aluminide coatings at relatively low temperatures

A method was presented to prepare aluminide coatings on metals by combining the pack aluminizing with the ball impact process. This technique applied mechanical vibration to a retort, which was loaded with pack-aluminizing powder, specimens and alloy balls. Pack aluminizing was carried out with repeated ball impact, which accelerated chemical reactions and atomic diffusion. Aluminide coatings were formed at a relatively lower temperature (below 600 ℃) and in a shorter treatment time, compared with the conventional pack aluminizing. The effects of the operation temperature and the treatment time on the formation of the coatings were analysed. The SEM, EDS and XRD analysis results show that the aluminide coatings appear to be homogeneous, with a high density and free of porosity, and have excellent adherence to the substrate. The coatings mainly consist of Al-rich phases such as η-Fe2Al5, θ-FeAl3 and ?CrAl5. Oxidation resistance was studied by high-temperature tests. The formation mechanism of the Al-coatings was also investigated. This technique provides a new approach for industrial diffusion coatings with great energy and time savings.

High-temperature corrosion-resistance performance of electro-thermal explosion spraying coating

As a new spraying technology used in the remanufacturing engineering, electro-thermal explosion spraying holds a lot of advantages. Electro-thermal explosion spraying coating aliquation phenomena are reduced and non-crystal, micro-crystal and millimicron-crystal and other microstructure are formed. The corrosion-resistance ability of electro-thermal explosion spraying coating in high temperature environment was surveyed respectively. SEM equipped with EDS was employed to analyze the microstructure of spraying coating before and after corrosion. The corrosion-resistance mechanism of the spraying coating was discussed.

On-line temperature monitoring and process diagnosis of plasma sprayed coatings

On-line temperature monitoring of plasma sprayed coating is presented, which is based on IR pyrometery combined to robot trajectories. Temperature fields of the substrate before spraying and the deposited coating when the damage happens are taken to investigate the temperature fluctuation information. Experimental results demonstrate that coating damage always occurs in the temperature transition area of the substrate from the higher to the lower, as well as the higher temperature area. The temperature difference between the peak and the mean of the relevant regions is beyond 30 - 50℃ or even higher. This case provides the omen of coating damage and the focusing scopes for the process control of coating temperature in plasma spraying

Preparation and Characterization of TiO_2/TiN/TiO_2 Multi-layer Solar Control Coatings Deposited by D.C. Reactive Magnetron Sputtering at Different Substrate Temperature

Transparent TiO2/TiN/TiO2 multi-layer solar control coatings were prepared on normal soda-lime-silica float glass substrate by using d.c. reactive magnetron sputtering at substrate temperature ranging from room temperature to 620℃ . The dependence of optical properties of the coatings and the coating composition, on the substrate temperature was studied. The results of the optical properties show that as the substrate temperature increases, a visible transmittance as high as 65% can be obtained. When the substrate temperature is higher than 370℃ , the infrared reflectance decreases. The results of X-ray photoelectron spectroscopy (XPS) show that when the substrate temperature is higher than 520℃ in oxygen atmosphere, the formation of thin surface over-layers (TiNxOy,) on top of the TiN films can be observed. When the substrate temperature is at 62℃ , the oxynitride become TiO2, which results in the optical degradation of TiN layer in infrared reflectance.

Effects of sintering temperature on the microstructural evolution and wear behavior of WCp reinforced Ni-based coatings

This article focuses on the microstructural evolution and wear behavior of 50wt%WC reinforced Ni-based composites prepared onto 304 stainless steel substrates by vacuum sintering at different sintering temperatures. The microstructure and chemical composition of the coatings were investigated by X-ray diffraction （XRD）, differential thermal analysis （DTA）, scanning and transmission electron microscopy （SEM and TEM） equipped with energy-dispersive X-ray spectroscopy （EDS）. The wear resistance of the coatings was tested by thrust washer testing. The mechanisms of the decomposition, dissolution, and precipitation of primary carbides, and their influences on the wear resistance have been discussed. The results indicate that the coating sintered at 1175℃ is composed of fine WC particles, coarse M6C （M=Ni, Fe, Co, etc.） carbides, and discrete borides dispersed in solid solution. Upon increasing the sintering temperature to 1225℃, the microstructure reveals few incompletely dissolved WC particles trapped in larger M6C, Cr-rich lamellar M23C6, and M3C2 in the austenite matrix. M23C6 and M3C2 precipitates are formed in both the γ/M6C grain boundary and the matrix. These large-sized and lamellar brittle phases tend to weaken the wear resistance of the composite coatings. The wear behavior is controlled simultaneously by both abrasive wear and adhesive wear. Among them, abrasive wear plays a major role in the wear process of the coating sintered at 1175℃, while the effect of adhesive wear is predominant in the coating sintered at 1225℃.

Influence of Ambient-Temperature Corrosion on the Oxidation Behavior of Al-Si Coatings

The high temperature oxidation behavior of Al Si coatings on the Ni base superalloy DZ125, with and without the ambient temperature corrosion test, was investigated. The results show that the isothermal oxidation behavior of the corroded coating changes, which has the higher mass gain than that of the original coating during the initial oxidation stage. Moreover, the cyclic oxidation resistance of the corroded coating decreases severely. The oxide scale was primarily composed of Al 2O 3, contaminated ...

High temperature corrosion behavior of arc-sprayed aluminum coatings on steel

Aluminum coatings were sprayed on the substrate of steel Q235 by arc spraying. The test samples of Q235, Al coatings and Al coatings with seal coat were placed in box type electric resistance furnace at 400, 500,600, 650 ℃ when their oxidation behaviors were studied. And their oxidation kinetics curves were protracted. Microstructure, microhardness, bond strength and distribution of section elements were investigated by optical microscope(OM), Vickers microhardness instrument, electric tensile test machine and EPMA. Al coatings and Al coatings with seal coat can enhance the oxidation-resistance of substrate under 500 ℃. The latter has the best corrosion resistance. The coatings can't protect the substrate against oxidation above 600 ℃. After a long time corrosion there is enriched oxygen element at interface.