Solvothermal synthesis and adsorption performance of layered boehmite using aluminum chloride and high-alumina fly ash

High alumina fly ash(FAHAl)is a kind of bulk solid waste unique to China,whose availability of high-value aluminum and the threat to the environment makes its high-value utilization urgent.In this work,the alumina containing leaching solution obtained from Na_(2)CO_(3) roasting and HCl leaching of FAHAl was used as the mother liquor to prepare layered boehmite in situ.The preparation process with AlCl_(3) as the raw material was also compared.The formation process and mechanism of boehmite,the choice of solvent,along with the adsorption capability of Congo red were analyzed by X-ray diffraction,scanning electron microscopy,Fourier transform infrared spectroscopy,Brunauer-Emmett-Teller method and adsorption experiments.Results showed that during the preparation of layered boehmite,the precursor Al(OH)_(3) from the reaction of Al^(3+) and OH-is transformed into boehmiteγ-AlOOH.The existence of ethanol is beneficial to regulate and promote the growth of boehmite crystal effectively.When water and ethanol are mixed with a volume ratio of 2:1 and used as the solvent,the maximum specific surface area of the boehmite is obtained at 135.7 m^(2)·g^(-1),and 99.16%of Congo red can be absorbed after 10 min when AlCl3 is used as a raw material.As purified leaching solution is used as the mother liquid,the crystallinity of boehmite decreases slightly when the pH value decreases from 12.5 to 11.When pH is 11,the removal efficiency of Congo red reaches a maximum of 72.25%.This process not only achieves the extraction of aluminum and high-value utilization of FAHAl but also provides a thought to prepare layered boehmite with adsorption properties.

Optimization of Fixture Number in Large Thin-Walled Parts Assembly Based on IPSO

There are lots of researches on fixture layout optimization for large thin-walled parts.Current researches focus on the positioning problem,i.e.,optimizing the positions of a constant number of fixtures.However,how to determine the number of fixtures is ignored.In most cases,the number of fixtures located on large thin-walled parts is determined based on engineering experience,which leads to huge fixture number and extra waste.Therefore,this paper constructs an optimization model to minimize the number of fixtures.The constraints are set in the optimization model to ensure that the part deformation is within the surface profile tolerance.In addition,the assembly gap between two parts is also controlled.To conduct the optimization,this paper develops an improved particle swarm optimization(IPSO)algorithm by integrating the shrinkage factor and adaptive inertia weight.In the algorithm,particles are encoded according to the fixture position.Each dimension of the particle is assigned to a sub-region by constraining the optional position range of each fixture to improve the optimization efficiency.Finally,a case study on ship curved panel assembly is provided to prove that our method can optimize the number of fixtures while meeting the assembly quality requirements.This research proposes a method to optimize the number of fixtures,which can reduce the number of fixtures and achieve deformation control at the same time.

Development of Fixture Layout Optimization for Thin-Walled Parts:A Review

An increasing number of researchers have researched fixture layout optimization for thin-walled part assembly during the past decades.However,few papers systematically review these researches.By analyzing existing literature,this paper summarizes the process of fixture layout optimization and the methods applied.The process of optimization is made up of optimization objective setting,assembly variation/deformation modeling,and fixture layout optimization.This paper makes a review of the fixture layout for thin-walled parts according to these three steps.First,two different kinds of optimization objectives are introduced.Researchers usually consider in-plane variations or out-of-plane deformations when designing objectives.Then,modeling methods for assembly variation and deformation are divided into two categories:Mechanism-based and data-based methods.Several common methods are discussed respectively.After that,optimization algorithms are reviewed systematically.There are two kinds of optimization algorithms:Traditional nonlinear programming and heuristic algorithms.Finally,discussions on the current situation are provided.The research direction of fixture layout optimization in the future is discussed from three aspects:Objective setting,improving modeling accuracy and optimization algorithms.Also,a new research point for fixture layout optimization is discussed.This paper systematically reviews the research on fixture layout optimization for thin-walled parts,and provides a reference for future research in this field.

A Systematic Review of Computer Vision Techniques for Quality Control in End-of-Line Visual Inspection of Antenna Parts

The rapid evolution of wireless communication technologies has underscored the critical role of antennas in ensuring seamless connectivity.Antenna defects,ranging from manufacturing imperfections to environmental wear,pose significant challenges to the reliability and performance of communication systems.This review paper navigates the landscape of antenna defect detection,emphasizing the need for a nuanced understanding of various defect types and the associated challenges in visual detection.This review paper serves as a valuable resource for researchers,engineers,and practitioners engaged in the design and maintenance of communication systems.The insights presented here pave the way for enhanced reliability in antenna systems through targeted defect detection measures.In this study,a comprehensive literature analysis on computer vision algorithms that are employed in end-of-line visual inspection of antenna parts is presented.The PRISMA principles will be followed throughout the review,and its goals are to provide a summary of recent research,identify relevant computer vision techniques,and evaluate how effective these techniques are in discovering defects during inspections.It contains articles from scholarly journals as well as papers presented at conferences up until June 2023.This research utilized search phrases that were relevant,and papers were chosen based on whether or not they met certain inclusion and exclusion criteria.In this study,several different computer vision approaches,such as feature extraction and defect classification,are broken down and analyzed.Additionally,their applicability and performance are discussed.The review highlights the significance of utilizing a wide variety of datasets and measurement criteria.The findings of this study add to the existing body of knowledge and point researchers in the direction of promising new areas of investigation,such as real-time inspection systems and multispectral imaging.This review,on its whole,offers a complete study of computer vision approaches for quality control in antenna parts.It does so by providing helpful insights and drawing attention to areas that require additional exploration.

Investigation of Microstructure and Phase Composition of Chromic Oxide, AZS/Cr and High-alumina Refractories after Exposure of Basalt and Aluminaboronsilicate Glasses Melts

The microstructure and phase composition of high-alumina,chromic oxide,and AZS/Cr refractories containing 30%and 60%(by mass)Cr_(2)O_(3) after exposure to aluminaboronsilicate glasses and basalt melts depending on the type of melts and temperature have been studied.The mechanisms of refractory corrosion by the used melts and the factors contributing to the inhibition of corrosion development have been investigated by the method of petrographic analysis.On the basis of obtained results,the use of high-alumina,chromic oxide,and AZS/Cr refractories in the sections of glass furnace linings,experiencing the intensive impact of aluminaboronsilicate glasses and basalt melts,has been confirmed and scientifically substantiated.

“三美论”视角下对比赏析When We Two Parted的汉译本——以查良铮和陈锡麟的译本为例

“三美论”是许渊冲先生提出的翻译理论,所谓的“三美”指的是意美、音美和形美。本文以许渊冲先生的“三美论”为理论指导,对比赏析查良铮和陈锡麟对乔治•戈登•拜伦诗歌When We Two Parted的两个中译本。从意美、音美和形美三个层面,对比赏析两个中译本对原文意境、诗歌节奏和尾韵以及诗歌形式上的再现。在诗歌汉译中,三美难以兼顾,译者在进行翻译时要分清主次,原则是意美大于音美,音美大于形美。

Geochemistry of Sulfur and Hazardous Elements in Late Paleozoic Coals and Partings from Taozao Coalfield, Shandong Province, China

The analyses of different sulfur forms, the trace elements in pyrites using electron microprobe and the trace elements in coal using INAA (instrumental neutron activation analysis) of the Late Paleozoic coals from the Taozao coalfield in Shandong Province, China, conclude that most sulfur (>75 %) in high-sulfur coal of Taiyuan Formation occurred as pyrite, in which many hazardous elements co-existed and their concentrations varied with their geological origin. The concentrations of hazardous elements in high-sulfur coals from Taiyuan Formation, composing mainly of Cu, As, U, Pb, Mo and Co, are much higher than those in the low-sulfur coals from Shanxi Formation and Shihezi Formation, because the influence of seawater during and after coal accumulation in Taiyuan Formation is stronger than those in Shanxi and Shihezi formations. Moreover, the element As is related to Fe, and both elements exist mainly in the form of pyrite. The element U is richer in the coal influenced by seawater. In addition, the coal affected by the magmatism contains more U, too. When high-sulfur coals are processed with heavy media washing to remove sulfur and minerals, the majority of hazardous elements will also be removed from the coals.

AN INTEGRATION BY PARTS FORMULA FOR STOCHASTIC HEAT EQUATIONS WITH FRACTIONAL NOISE

In this paper,we establish the integration by parts formula for the solution of fractional noise driven stochastic heat equations using the method of coupling.As an application,we also obtain the shift Harnack inequalities.

小尾寒羊不同部位风味物质与风味前体物的相关性分析

以6~7月龄、体质量为50 kg的小尾寒羊为实验对象,选取颈肉(NM)、里脊(LLDM)和腿肉(RG),对小尾寒羊挥发性风味物质、脂肪酸和氨基酸进行相关性分析。结果表明:在3个部位共检测到45种挥发性风味物质,其中醛类是最主要的挥发性风味物质,占总挥发性风味物质的50%左右。经主成分分析得知,庚醛、壬醛、苯甲醛等24种风味物质是导致不同部位间挥发性风味物质差异的主要影响因素。LLDM中对人体有益的单不饱和脂肪酸和多不饱和脂肪酸含量均为最高,脂肪酸比例更符合人体对羊肉脂肪酸营养价值的需求,对人体健康更有益。氨基酸中以谷氨酸(Glu)和赖氨酸(Lys)为主,约占总氨基酸的17%和10%,其中RG除蛋氨酸(Met)、酪氨酸(Tyr)、赖氨酸(Lys)外含量均为最高,且除谷氨酸(Glu)和脯氨酸(Pro)外与LLDM差异不显著,与NM差异均显著。相关性分析表明,多不饱和脂肪酸与大多数挥发性风味物质呈正相关,且与醛类、醇类和芳香类等挥发性风味物质呈显著正相关,这可能是因为多不饱和脂肪酸极易氧化,在氧化过程中生成醛类、醇类和芳香类等物质。氨基酸与大多数醛类和醇类都呈正相关,这可能是因为氨基酸通过转氨反应等一系列反应,最终生成醛类和醇类等物质。

框类薄壁件装夹布局与加工参数研究

针对航空隔框类薄壁件在铣削加工中极易产生变形等问题,通过有限元软件ABAQUS研究了铣削过程中装夹布局和铣削参数对薄壁件加工变形量的影响。首先根据装夹有限元模型,分析装夹位置和夹紧顺序对薄壁件变形量的影响,并在装夹仿真的基础上建立了铣削加工模型,设计正交试验得到不同铣削加工参数下薄壁件的变形量;其次以仿真数据为样本,使用BP神经网络和遗传算法对装夹布局和铣削参数进行优化;最后对优化结果进行实验验证,结果显示仿真与实验数据比较符合,最小偏差为4.38%,最大偏差为9.35%。研究结果表明:通过有限元仿真试验辅助选取薄壁件的铣削加工参数,能充分地提高航空薄壁件的加工质量。

基于机器视觉的飞机故障检查系统

针对当前飞机维修检查工作以人工目视检查为主、效率低且存在人为因素影响的情况,设计一套基于图像识别与机器深度学习的飞机部件表面无损检测系统。收集并整理了某航空公司一线飞机维修员拍摄的飞机机身及发动机部件图片,对图片集进行预处理,包括通道提取、Sobel滤波处理及二值化;最后用Blob分析对处理后的图像进行特征提取与系统分析。系统运行速度快、准确率高且可连续自动识别图像。利用机器视觉技术对飞机部件表面进行无损检测不仅可以提高生产效率,同时可以去除人为因素对航空器飞行安全的影响,使得飞机的飞行安全得到进一步提升。实践证明,该系统性能稳定可靠,具有极高的推广应用价值。

存算分离架构下Part元数据的单独管理策略

针对ClickHouse存在的硬件资源无法被充分利用、缺少弹性和节点启动过慢的问题,在存算分离架构下,提出了一套针对描述数据信息的元数据(Part元数据)的管理策略. Part元数据是元数据中最重要的组成成分.为了能够有效管理远程共享存储上的数据,采集了所有Part元数据文件,并将其合并后,经过键值映射、序列化和反序列化,存入分布式键值数据库中.此外,还设计了一套同步策略,以确保远程共享存储上的数据与分布式键值数据库中的元数据的一致性.利用Part元数据管理策略及相关的同步策略,实现了一个针对Part元数据的管理系统,解决了ClickHouse节点启动过慢的问题,并支持高效的节点动态扩缩容.

非理性偏好下动力电池再制造供应链最优决策与协调研究

考虑动力电池剩余容量不确定特征,构建由电池供应商和汽车制造商组成的再制造供应链,分别探讨决策双方完全理性、单向非理性偏好和双向非理性偏好等5种决策情形下的均衡解。研究发现:动力电池再制造容量起始点对回收量具有正向作用。在双向非理性偏好情形下,供应商的利他(公平)偏好程度增加导致制造商和系统总利润提高(降低),而自身利润总是降低;制造商的非理性偏好对供应链成员及系统利润的影响与供应商的非理性偏好程度有关。在单向非理性情形下,供应链成员的利他(公平)偏好程度增加导致自身利润下降(上升)而对方利润上升(下降)。两部定价契约和收益共享契约能够实现双向非理性偏好情形下再制造供应链的协调。

盖板件高效铣削表面粗糙度预测与工艺参数优化

为了保证7075铝合金盖板件铣削表面质量和提高铣削加工效率,进行工艺参数优化,通过响应曲面法(RSM)构建铣削加工表面粗糙度预测模型,分析铣削工艺参数对表面粗糙度的影响规律。基于表面粗糙度预测模型建立高效铣削工艺参数优化目标方程,采用改进的粒子群算法(PSO)对目标方程进行优化,运用优化后的工艺参数对某盖板件进行铣削加工。试验结果表明:采用优化后的工艺参数进行盖板件铣削加工可以满足表面粗糙度要求,验证了预测模型的准确性和改进PSO方法的可行性。

老旧直升机维修中无损检测技术的应用

随着使用年限的增长,老旧直升机结构性故障和偶发性故障逐渐增多,给维护修理带来了诸多困难,维护人员常常不能及时发现和消除故障隐患。针对当前老旧直升机的特点和维修现状,介绍了无损检测技术在航空维修领域中的应用,结合直升机结构特点和使用情况探讨确定老旧直升机无损检测的重点部位和关键部件,围绕不同无损检测技术特点对直升机关键部件检测的具体应用方法进行阐述,并结合老旧直升机维护实践对无损检测技术的使用时机做出探讨和研究,最后对无损检测技术在老旧直升机维修中的应用前景进行了展望。

基于OBE理念的发电厂电气部分课程建设

发电厂电气部分是电气工程及其自动化专业重要的专业课程,对学生工程实践能力的培养起到重要的支撑作用。该文基于成果导向教育理念(OBE),建立MOOC教学平台的“课前-课中-课后”线上线下混合式闭环教学模式,构建丰富的教学资源,课程教学目标支撑毕业要求,构建成果导向的课程考核评价体系,体现以学生学习为中心。在新的教学模式下,学生学习效果明显改善。在OBE理念指导下,通过MOOC平台进行电气类专业课程改革是改进教学方法、提升教学质量的有效手段,也是未来教学改革的方向。

大跨越架空输电导线铝部应力分布试验

为了掌握大跨越架空输电导线铝部应力空间分布特性,以JLHA1/G6A-500/280型特强钢芯铝合金导线为研究对象,采用铝股丝表面激光刻槽,内嵌高灵敏、超大复用容量超弱光纤光栅,搭建了大跨越输电导线铝部应力试验平台,研究了不同张力条件下大跨越架空输电导线铝部应力分布规律,建立了大跨越导线实体有限元模型,分析了铝股应力分布特征,并验证了试验结果的正确性。结果表明:导线承受张力作用时,外层铝股和次外层铝股应力不同,外层铝股应力小于次外层铝股应力,导线同层铝股应力基本相同;铝股应力随导线张力的增大呈线性增大趋势,张力每增大1%,铝股应力增大约10%。不同导线张力作用时钢股和铝股应力均呈现环状分层特性,铝股平均应力小于钢股平均应力,铝部和钢股应力比约为3∶7;外层和次外层铝合金股丝应力沿圆周向分布不均匀,建议大跨越导线线型设计时考虑铝股丝分层特性。

养心草提取物抗肺癌活性部位筛选

目的筛选养心草抗肺癌活性部位。方法运用系统溶剂法制备养心草各提取部位;体外培养肝癌A549细胞,采用MTT法检测细胞株半数抑制浓度(IC50),以IC50作为评价指标,初步筛选出养心草抗肿瘤的有效部位。同时,建立肺癌LLC细胞移植瘤小鼠模型,通过观察肿瘤体积、小鼠体质量、脏器指数及瘤体质量的变化,对养心草的抗肿瘤效果进行评价养心草石油醚部位及乙酸乙酯部位的体内抗肺癌作用。结果MTT实验结果表明养心草不同提取部位中石油醚部位和乙酸乙酯部位对肺癌A549细胞的增殖显示较强的抑制作用;体内小鼠肺癌LLC细胞移植瘤实验表明石油醚部位和乙酸乙酯部位可明显抑制小鼠肿瘤的生长(P<0.05),且具有剂量依赖性,并对鼠体质量及脏器指数未产生显著影响(P>0.05)。结论养心草的石油醚部位和乙酸乙酯部位是其抗肺癌的有效部位。

新疆肉苁蓉不同品种与部位间活性成分差异及抗氧化活性分析

本文评估了新疆和田策勒县梭梭肉苁蓉、红柳肉苁蓉的不同部位的活性成分含量及抗氧化能力。结果表明:红柳肉苁蓉的总多酚、总黄酮、总糖、毛蕊花糖苷含量均表现为下部含量最高,中部、上部含量递减。其中红柳肉苁蓉下部的总多酚、总黄酮含量(38.35 mg GAE/g DW、35.61 mg RE/g DW)分别为梭梭肉苁蓉下部的2.47、10.95倍。梭梭上部松果菊苷含量在两种肉苁蓉不同部位中最高,为92.93 mg/g DW,两种肉苁蓉下部总三萜含量显著高于上部、中部(P<0.05),梭梭下部总三萜最多,为6.75 mg OAE/g DW。此外,梭梭肉苁蓉和红柳肉苁蓉均表现出较强的抗氧化性,并且肉苁蓉下部的抗氧化效果最好,其IC50 DPPH分别为7.15和5.95 mg/mL,IC_(50 ABTS)_(+)分别为5.19和3.28 mg/mL。相关性分析表明,肉苁蓉中的总多酚、总黄酮、原花青素、总糖、毛蕊花糖苷含量与IC_(50 DPPH)和IC_(50 ABTS)^(+)呈负相关。结果表明,梭梭肉苁蓉上部的松果菊苷含量丰富,红柳肉苁蓉下部的总多酚、总黄酮、总糖、毛蕊花糖苷含量丰富且高于梭梭肉苁蓉对应部位。本文可以为不同产地肉苁蓉标准化及功能性产品深度研发提供理论基础。