3D modeling for effect of tool eccentricity on coupled thermal and material flow characteristics during friction stir welding

A novel three-dimensional numerical model is proposed to investigate the effect of tool eccentricity on the coupled thermal and material flow characteristics in friction stir welding(FSW) process.An asymmetrical boundary condition at the tool-workpiece interface,and the dynamic mesh technique are both employed for the consideration of the tool eccentricity during tool rotating.It is found that tool eccentricity induces the periodical variation of the heat densities both at the tool-workpiece interface and inside the shear layer,but the fluctuation amplitudes of the heat density variations are limited.However,it is demonstrated that tool eccentricity results in significant variation of the material flow behavior in one tool rotating period.Moreover,the material velocity variation at the retreating side is particularly important for the formation of the periodic characteristics in FSW.The modeling result is found to be in good agreement with the experimental one.

LDH sealing for PEO coated friction stir welded AZ31/AA5754 materials

The need to combine various metals in light-weight constructions requires the development of coatings that prevent galvanic corrosion.Layered double hydroxides(LDHs)can be an example of such coatings,which were previously successfully obtained in situ on individual materials.In addition,the possibility of LDH growth(including LDH growth in the presence of chelating agents)on the surface of plasma electrolytic oxidation(PEO)-coated metals was previously shown.This PEO+LDH combination could improve both corrosion and mechanical characteristics of the system.The possibility of LDHs formation in situ on the surface of PEO-coated friction stir welded(FSW)magnesium-aluminum materials(AZ31/AA5754 system was selected as a model one)was demonstrated in the presence of 1,3-diamino-2-hydroxypropane-N,N,N',N'-tetraacetic acid(DHPTA)as a chelating agent,which was selected based on analysis of respective metal-ligand compounds stability.LDHs growth was achieved under ambient pressure without addition of carbonates in the electrolyte.The effectiveness of the resulting coating is shown both for corrosion resistance and hardness.

Materials flow and phase transformation in friction stir welding of Al 6013/Mg

Material flow and phase transformation were studied at the interface of dissimilar joint between Al 6013 and Mg, produced by stir friction welding （FSW） experiments. Defect-free weld was obtained when aluminum and magnesium were placed in the advancing side and retreating side respectively and the tool was placed 1 mm off the weld centerline into the aluminum side. In order to understand the material flow during FSW, steel shots were implanted as indexes into the welding path. After welding, using X-ray images, secondary positions of the steel shots were evaluated. It was revealed that steel shots implanted in advancing side were penetrated from the advancing side into the retreating side, whereas the shots implanted in the retreating side remained in the retreating side, without penetrating into the advancing side. The welded specimens were also heat treated. The effects of heat treatment on the mechanical properties of the welds and the formation of new intermetallic layers were investigated. Two intermetallic compounds, Al3Mg2 and Al12Mg17, were formed sequentially at Al6013/Mg interface.

Underwater Laser Welding/Cladding for High-performance Repair of Marine Metal Materials:A Review

With the rapid developments of marine resource exploitation,mounts of marine engineering equipment are settled on the ocean.When it is not possible to move the damaged equipment into a dry dock,welding operations must be performed in underwater environments.The underwater laser welding/cladding technique is a promising and advanced technique which could be widely applied to the maintenance of the damaged equipment.The present review paper aims to present a critical analysis and engineering overview of the underwater laser welding/cladding technique.First,we elaborated recent advances and key issues of drainage nozzles all over the world.Next,we presented the underwater laser processing and microstructural-mechanical behavior of repaired marine materials.Then,the newly developed powder-feeding based and wire-feeding based underwater laser direct metal deposition techniques were reviewed.The differences between the convection,conduction,and the metallurgical kinetics in the melt pools during underwater laser direct metal deposition and in-air laser direct metal deposition were illustrated.After that,several challenges that need to be overcame to achieve the full potential of the underwater laser welding/cladding technique are proposed.Finally,suggestions for future directions to aid the development of underwater laser welding/cladding technology and underwater metallurgical theory are provided.The present review will not only enrich the knowledge in the underwater repair technology,but also provide important guidance for the potential applications of the technology on the marine engineering.

Microstructure and mechanical properties of butt joints of QCr0.8/1Cr21Ni5Ti equal-thickness dissimilar materials by electron beam welding

Butt joints of QCr0.8/1Cr21Ni5Ti equal-thickness dissimilar materials were obtained by electron beam welding with fixed accelerating voltage 60 kV and focus current ~1.99 A , changed electron beam current and welding velocity. Microstructure and composition of the EBW joint were investigated by means of optical micrography and EDX analysis, mechanical properties of the joint were also tested. The results show that joint’s macrostructure was divided into three zones: top weld zone near QCr0.8 and bottom weld zone consisting of Cu(ss.Fe) with a certain amount of dispersedly distributed (α+ε) mixed microstructure, middle weld zone consisting of (α+ε) microstructure with a small amount of Cu(ss.Fe) particles. Morphological inhomogeneous macrostructure and uneven chemical compostion of QCr0.8/1Cr21Ni5Ti joint by EBW are the most important factor to result in decreasing joining strength.

The effect of welding materials on 1Cr18Ni9Ti and 2Cr13 steel welded joints electrochemical properties

By method of TIG,two kinds of welding materials were filled in and under certain welding craft conditions,1Cr18Ni9Ti and 2Cr13 were welded.The microstructure of two kinds of welded joints were observed and analyzed by OM,SEM.Through seawater immersion test,polarization curves and AC impedance spectroscopy of two kinds of welding joints were obtained.The results show that 2Cr13 and 1Cr18Ni9Ti welded joints are typical columnar crystal,the microstructure is lath martensite+austenite+carbide.The welded joints that filled in 308 and H1Cr21Ni10Mn7Mo welding wires,corrosion resistance has same change rule:Austenite base metal>HAZ near Austenite>welded joint>HAZ near Martensite>Martensite base metal.The every zone contrast of two kinds of welded joint corrosion resistance obtains:the welded joints filled in 308>the welded joints filled in H1Cr21Ni10Mn7Mo.

Development of processing windows for friction stir spot welding of aluminium Al5052/copper C27200 dissimilar materials

Friction stir spot welding technique was used to join dissimilar combinations of aluminium alloy(Al5052)with copperalloy(C27200)and friction stir spot welding windows such as tool rotational speed–dwell time and tool rotational speed?plungedepth diagrams for effective joining of these materials were developed.Using a central composite design model,empirical relationswere developed to predict the changes in tensile shear failure load values and interface hardness of the joints with three processparameters such as tool rotational speed,plunge depth and dwell time.The adequacy of the developed model was verified usingANOVA analysis at95%confidence level.Response surface methodology was used to optimize the developed model to maximizetensile strength and minimize interface hardness.A high tensile shear failure load value of3850N and low interface hardness valueof HV81was observed for joints made under optimum conditions,and validation experiments confirmed the high predictability ofthe developed model with error less than2%.The operating windows developed shall act as reference maps for future designengineers in choosing appropriate friction stir spot welding process parameter values to obtain good joints.

Application and prospect of computer technology in welding materials field

This paper summarizes the application status of computer technology in welding materials field from three aspects: the CAD of welding materials, the date base system for welding materials and the expert system for welding materials .Besides, this paper explores and discusses the existing problems and the developing trend in the future.

Visualization and simulation of plastic material flow in friction stir welding of 2024 aluminium alloy plates

Thin copper sheets as marker material were embedded into weld path of 2024 aluminium alloy plates and their final position after friction stir welding was examined by metallographic techniques. Referring to the visualized material flow patterns, a three-dimensional model was developed to conduct the numerical simulation of the temperature profile and plastic material flow in friction stir welding. The calculated velocity contour of plastic flow in close proximity of the tool is generally consistent with the visualized results. As the tool rotation speed increases at a constant tool travel speed, the material flow near the pin gets stronger. The predicted shape and size of the weld nugget zone match with the experimentally measured ones.

Electron-Beam Welding Joint Strength of Dissimilar Materials

This paper provides an in-depth discussion of the joint strength of electron beam welding of dissimilar materials.The effect of welding parameters and material properties on the joint strength was analyzed,and an argument for the optimal parameter combination is presented.Electron-beam welding technology offers several advantages,including high energy density and the ability to create fine weld seams.However,it also presents certain challenges,such as the complexity of welding parameters and the potential generation of brittle phases.The analysis conducted in this paper holds significant importance in enhancing the quality and efficiency of dissimilar material welding processes.

Simulation of 3D material flow in friction stir welding of AA6061-T6

This paper reports the numerical simulation of the 3D material flow in friction stir welding process by using finite element methods based on solid mechanics. It is found that the material flow behind the pin is much faster than that in front of the pin. The material in front of the pin moves upwards and then rotates with the pin due to the effect of the rotating tool. Behind of the pin, the material moves downwards. This process of material movement is the real cause to make the friction stir welding process continuing successfully. With the increase of the translational velocity or the rotational velocity of the pin, the material flow becomes faster.

3D visualization of the material flow in friction stir welding process

The material flow in friction stir welded 2014 Al alloy has been investigated using a marker insert technique （MIT）. Results of the flow visualization show that the material flow is asymmetrical during the friction stir welding （FSW） process and there are also significant differences in the flow patterns observed on advancing side and retreating side. On advancing side, some material transport forward and some move backward, but on retreating side, material only transport backward. At the top surface of the weld, significant material transport forward due to the action of the rotating tool shoulder. Combining the data from all the markers, a three-dituensional flow visualization, similar to the 3D image reconstruction technique, was obtained. The three-dimensional plot gives the tendency chart of material flow in friction stir welding process and from the plot it can be seen that there is a vertical, circular motion around the longitudinal axis of the weld. On the advancing side of the weld, the material is pushed downward but on the retreating side, the material is pushed toward the crown of the weld. The net result of the two relative motions in both side of the advancing and the retreating is that a circular motion comes into being. Comparatively, the material flow around the longitudinal axis is a secondary motion.

Numerical simulations on material flow behaviors in whole process of friction stir welding

A finite element model based on solid mechanics was developed with ABAQUS to study the material flow in wholeprocess of friction stir welding （FSW）, with the technique of tracer particles. Simulation results indicate that the flow pattern of thetracer particles around the pin is spiral movement. There are very different flow patterns at the upper and lower parts of the weld. Thematerial on the upper surface has the spiral downward movement that is affected by the shoulder and the lower material has the spiralupward movement that is affected by the pin. The velocity of the material flow on the periphery of the stirring pin is higher than thatat the bottom of the stirring pin. The material can be rotated with a stirring pin a few times, agreeing well with the previousexperimental observation by tungsten tracer particles.

Influence of welding parameters on material flow,mechanical property and intermetallic characterization of friction stir welded AA6063 to HCP copper dissimilar butt joint without offset

Joining of dissimilar aluminium-copper is an emerging area of interest for both research and industry due to its complex nature.Friction stir welding was attempted to evaluate the joint strength without offset at the butt line between AA6063 to HCP copper sheet under different combination of rotational speed of 800 and 1000 r/min and travel speed of 20 and 40 mm/min.Material flow was studied in detail for different combinations of parameters with optical microscopy and elemental mapping by energy dispersive X-ray spectroscopy（EDS）.The results were correlated with the microstructural characteristics and formation of intermetallics at the bond interface using microhardness test and X-ray diffraction（XRD） technique.Material flow clearly suggests that energy input at 800 r/min and 20 mm/min is sufficient to plasticize both the materials with formation of higher amount of thermodynamically stable and hard intermetallic phases Al4Cu9 and Al Cu4（slower cooling rate of 88 K/s） than that at 800 r/min and 40 mm/min（faster cooling rate of 154 K/s）,attributed maximum joint strength（~78.6% of aluminium base metal）.

Effect of welding speed on the material flow patterns in friction stir welding of AZ31 magnesium alloy

The clear zigzag-line pattern on transverse cross sections can be used to explain the formation mechanism of the weld nugget when friction stir welded AZ31 magnesium alloy without any other insert material is used as mark. It provides a simple and useful method to research the joining mechanism of friction stir welding. The rotation speed is kept at 1000 r/min and the welding speed changes from 120 mm/min to 600 mm/min. The macrostructure on the transverse cross section was divided into several parts by faying surface. The results show that the shape and formation procedure of the weld nugget change with the welding speed. There are two main material flows in the weld nugget： one is from the advancing side and the other is from the retreating side. A simple model on the weld nugget formation of FSW is presented in this article.

Analysis of material flow and heat transfer in friction stir welding of aluminium alloys

A three-dimensional viscous-plastic.finite element model is established based on computational fluid mechanics. The material during the welding process is considered as non-Newtonian fluid abided by Norton-Hoff constitutive law, and viscous dissipation is assumed as the unique heat source. The model is used to numerically simulate the material flow and heat transfer in friction stir welding, and capture some useful process characteristics, .such as heat generation, temperature distribution and fluid.flow; besides, the velocity field is used to calculate streamlines of material flow, and the dimension of the deformation zone is measured.

Indirect Measurement of Material Thermal and Mechanical Properties during Welding

By means of a newly developed non-contact detecting method, electronic speckle pattern interferometry (ESPI), a method of determining material property data during welding is studied. A TIG fixed-point welding process is modeled in which some achievements of simulation, such as the effect of welding pool on temperature field and nonlinear relation between convection coefficient and temperature, are all considered. In addition, by taking into account effect of heating rate, the workpiece is divided into near-weld zone and far-weld zone, which will be treated with different property values. When the displacement field computed with original property data is compared and matched with the experimental displacement field, which is measured by ESPI, these original data are adjusted properly. A group of raw properties are obtained and are corrected by statistical regression before they enter the simulation process again.By such a loop of "simulation-comparison-modification", a set of property data that best satisfy the real condition are achieved finally. In such a way, a new method for measuring material properties during welding is found.

Exploring material flow in friction stir welding using stacked structure of 2024 and 6061 aluminum alloys

An experimental technique based on stacked structures was developed to observe the material flow behavior of the friction stir welding （FSW） process. Analysis of section views along different directions revealed important new details of the material flow in FSW process. In this work, a general flow model of FSW was constructed based on the analysis of different static section views of stacked structure weld. The formation of onion rings was found to be a geometric effect due to layered deposition attd the extrusion occurred at the interface between flow arm （FA） and stirring zone （SZ）.

Modeling of material flow in friction stir welding process

This paper presents a 3D numerical model to study the material flow in the friction stir welding process. Results indicate that the material in front of the pin moves upwards due to the extrusion of the pin, and then the upward material rotates with the pin. Behind the rotating tool, the material starts to move downwards and to deposit in the wake. This process is the real cause to make friction stir welding process continuing successfully. The tangent movement of the material takes the main contribution to the flow of the material in friction stir welding process. There exists a swirl on the advancing side and with the increase of the translational velocity the inverse flow of the material on the advancing side becomes faster. The shoulder can increase the velocity of material flow in both radial direction and tangent direction near the top surface. The variations of process parameters do have an effect on the velocity field near the pin, especially in the region in which the material flow is faster.

Material flow behavior and microstructural evolution during refill friction stir spot welding of alclad 2A12-T4 aluminum alloy

In this study, we used the stop-action technique to experimentally investigate the material flow and microstructural evolution of alclad 2A12-T4 aluminum alloy during refill friction stir spot welding.There are two material flow components, i.e., the inward-or outward-directed spiral flow on the horizontal plane and the upward-or downward-directed flow on the vertical plane.In the plunge stage, the flow of plasticized metal into the cavity is similar to that of a stack, whereby the upper layer is pushed upward by the lower layer.In the refill stage, this is process reversed.As such, there is no obvious vertical plasticized metal flow between adjacent layers.Welding leads to the coarsening of S(Al2CuMg) in the thermo-mechanically affected zone and the diminishing of S in the stir zone.Continuous dynamic recrystallization results in the formation of fine equiaxed grains in the stir zone, but this process becomes difficult in the thermo-mechanically affected zone due to the lower deformation rate and the pinning action of S precipitates on the dislocations and sub-grain boundaries, which leads to a high fraction of low-angle grain boundaries in this zone.