An in-situ self-etching enabled high-power electrode for aqueous zinc-ion batteries

Sluggish storage kinetics is considered as the main bottleneck of cathode materials for fast-charging aqueous zinc-ion batteries(AZIBs).In this report,we propose a novel in-situ self-etching strategy to unlock the Palm tree-like vanadium oxide/carbon nanofiber membrane(P-VO/C)as a robust freestanding electrode.Comprehensive investigations including the finite element simulation,in-situ X-ray diffraction,and in-situ electrochemical impedance spectroscopy disclosed it an electrochemically induced phase transformation mechanism from VO to layered Zn_(x)V_(2)O_5·nH_(2)O,as well as superior storage kinetics with ultrahigh pseudocapacitive contribution.As demonstrated,such electrode can remain a specific capacity of 285 mA h g^(-1)after 100 cycles at 1 A g^(-1),144.4 mA h g^(-1)after 1500 cycles at 30 A g^(-1),and even 97 mA h g^(-1)after 3000 cycles at 60 A g^(-1),respectively.Unexpectedly,an impressive power density of 78.9 kW kg^(-1)at the super-high current density of 100 A g^(-1)also can be achieved.Such design concept of in-situ self-etching free-standing electrode can provide a brand-new insight into extending the pseudocapacitive storage limit,so as to promote the development of high-power energy storage devices including but not limited to AZIBs.

Numerical Investigation on Thermal Performance of Two-Phase Immersion Cooling Method for High-Power Electronics

The power density of electronic components grows continuously,and the subsequent heat accumulation and temperature increase inevitably affect electronic equipment’s stability,reliability and service life.Therefore,achieving efficient cooling in limited space has become a key problem in updating electronic devices with high performance and high integration.Two-phase immersion is a novel cooling method.The computational fluid dynamics(CFD)method is used to investigate the cooling performance of two-phase immersion cooling on high-power electronics.The two-dimensional CFD model is utilized by the volume of fluid(VOF)method and Reynolds StressModel.Lee’s model was employed to calculate the phase change rate.The heat transfer coefficient along the heatedwalls and the shear-lift force on bubbles are calculated.The simulation data are verified with the literature results.The cooling performance of different coolants has been studied.The results indicate that the boiling heat transfer coefficient can be enhanced by using a low boiling point coolant.The methanol is used as the cooling medium for further research.In addition,the mass flow rate and inlet temperature are investigated to assess the thermal performance of twophase immersion cooling.The average temperature of the high-power electronics is 80℃,and the temperature difference can be constrained to 8℃.Meanwhile,the convective heat transfer coefficient reaches 2740 W/(m2・℃)when the inlet temperature is 50℃,and the mass flow rate is 0.3 kg/s.In conclusion,the results demonstrated that two-phase immersion cooling has provided an effective method for the thermal management of high-power electronics.

An open-end high-power microwave-induced fracturing system for hard rock

Microwave pre-treatment is considered as a promising technique for alleviating cutter wear. This paper introduces a high-power microwave-induced fracturing system for hard rock. The test system consists of a high-power microwave subsystem (100 kW), a true triaxial testing machine, a dynamic monitoring subsystem, and an electromagnetic shielding subsystem. It can realize rapid microwave-induced fracturing, intelligent tuning of impedance, dynamic feedback under strong microwave fields, and active control of microwave parameters by addressing the following issues: the instability and insecurity of the system, the discharge breakdown between coaxial lines during high-power microwave output, and a lack of feedback of rock-microwave response. In this study, microwave-induced surface and borehole fracturing tests under true triaxial stress were carried out. Experimental comparisons imply that high-power microwave irradiation can reduce the fracturing time of hard rock and that the fracture range (160 mm) of a 915-MHz microwave source is about three times that of 2.45 GHz. After microwave-induced borehole fracturing, many tensile cracks occur on the rock surface and in the borehole: the maximum reduction of the P-wave velocity is 12.8%. The test results show that a high-power microwave source of 915 MHz is more conducive to assisting mechanical rock breaking and destressing. The system can promote the development of microwave-assisted rock breaking equipment.

Impact of amplified spontaneous emission noise on the SRS threshold of high-power fiber amplifiers

Impact of amplified spontaneous emission(ASE)noise on the stimulated Raman scattering(SRS)threshold of highpower fiber amplifiers is demonstrated numerically through a spectral evolution approach.The simulation results confirm that ASE noise in the Raman wavelength band could reduce the SRS threshold of high-power fiber amplifiers significantly.As for ASE noise originated the main amplifier,it becomes stronger and reduces the SRS threshold at shorter operation wavelength below 1052 nm.As for ASE noise originated from the seed laser,it reduces the SRS threshold at different operation wavelength under the condition that the Raman ratio is over-90 dB in the seed laser.The theoretical method and results in this work could provide a well reference to extend the operation wavelength of high-power fiber lasers.

On the Mean Value of High-Powers of a Special Character Sum Modulo a Prime

In this paper,we use the elementary methods,the properties of Dirichlet character sums and the classical Gauss sums to study the estimation of the mean value of high-powers for a special character sum modulo a prime,and derive an exact computational formula.It can be conveniently programmed by the“Mathematica”software,by which we can get the exact results easily.

Analysis of high-power disk laser welding stability based on classification of plume and spatter characteristics

Classification of plume and spatter images was studied to evaluate the welding stability. A high-speed camera was used to capture the instantaneous images of plume and spatters during high power disk laser welding. Characteristic parameters such as the area and number of spatters, the average grayscale of a spatter image, the entropy of a spatter grayscale image, the coordinate ratio of the plume centroid and the welding point, the polar coordinates of the plume centroid were defined and extracted. Karhunen-Loeve transform method was used to change the seven characteristics into three primary characteristics to reduce the dimensions. Also, K-nearest neighbor method was used to classify the plume and spatter images into two categories such as good and poor welding quality. The results show that plume and spatter have a close relationship with the welding stability, and two categories could be recognized effectively using K-nearest neighbor method based on Karhunen-Loeve transform.

Three-dimensional simulation method of multipactor in microwave components for high-power space application

Based on the particle-in-cell technology and the secondary electron emission theory, a three-dimensional simulation method for multipactor is presented in this paper. By combining the finite difference time domain method and the panicle tracing method, such an algorithm is self-consistent and accurate since the interaction between electromagnetic fields and particles is properly modeled. In the time domain aspect, the generation of multipactor can be easily visualized, which makes it possible to gain a deeper insight into the physical mechanism of this effect. In addition to the classic secondary electron emission model, the measured practical secondary electron yield is used, which increases the accuracy of the algorithm. In order to validate the method, the impedance transformer and ridge waveguide filter are studied. By analyzing the evolution of the secondaries obtained by our method, multipactor thresholds of these components are estimated, which show good agreement with the experimental results. Furthermore, the most sensitive positions where multipactor occurs are determined from the phase focusing phenomenon, which is very meaningful for multipactor analysis and design.

Ti-containing hydrogenated carbon films fabricated by high-power plasma magnetron sputtering

To improve the characteristics of a diamond-like carbon （DLC） film, Ti-containing amorphous hydrogenated carbon thin films were deposited on sus304 stainless steel substrates by high-power plasma-sputtering with titanium metal as the solid plasma source in a mixed ArC2H2 atmosphere. The films were fabricated to obtain a multilayered structure of Ti/TiC/DLC gradient for improving adhesion and reducing residual stress. The effects of substrate bias and target-substrate distance on the films＇ properties were studied by glow discharge spectroscope, X-ray diffractometer, Raman spectroscope, nanoindenter, and a pin-on-disk tribometer. The results indicate that the films possess superior adhesive strength and toughness.

Damage effects and mechanism of the silicon NPN monolithic composite transistor induced by high-power microwaves

A two-dimensional model of the silicon NPN monolithic composite transistor is established for the first time by utilizing the semiconductor device simulator, Sentaurus-TCAD. By analyzing the internal distributions of electric field, current density, and temperature of the device, a detailed investigation on the damage process and mechanism induced by high-power microwaves （HPM） is performed. The results indicate that the temperature elevation occurs in the negative half-period and the temperature drop process is in the positive half-period under the HPM injection from the output port. The damage point is located near the edge of the base-emitter junction of T2, while with the input injection it exists between the base and the emitter of T2. Comparing these two kinds of injection, the input injection is more likely to damage the device than the output injection. The dependences of the damage energy threshold and the damage power threshold causing the device failure on the pulse-width are obtained, and the formulas obtained have the same form as the experimental equations, which demonstrates that more power is required to destroy the device if the pulse-width is shorter. Furthermore, the simulation result in this paper has a good coincidence with the experimental result.

Design and Simulation of High-power LED Array Packaging

Thermal management is one of the key technologies for high-power Light emitting diode(LED)entering into the general illuminating field.Successful thermal management depends on optimal packaging structure and selected packaging materials.In this paper,the aluminum is employed as a substrate of LED,3×3 array chips are placed on the substrate,heat dissipation performance is simulated using finite element analysis(FEA)software,analyzed are the influences on the temperature of the chip with different convection coefficient,and optical properties are simulated using optical analysis software.The results show that the packaging structure can not only effectually improve the thermal performance of high-power LED array but also increase the light extraction efficiency.

Design and high-power test of 800-kW UHF klystron for CEPC

To reduce the energy demand and operation cost for circular electron positron collider(CEPC), the high efficiency klystrons are being developed at Institute of High Energy Physics, Chinese Academy of Sciences. A 800-k W continuous wave(CW) klystron operating at frequency of 650-MHz has been designed. The results of beam–wave interaction simulation with several different codes are presented. The efficiency is optimized to be 65% with a second harmonic cavity in three-dimensional(3D) particle-in-cell code CST. The effect of cavity frequency error and mismatch load on efficiency of klystron have been investigated. The design and cold test of reentrant cavities are described, which meet the requirements of RF section design. So far, the manufacturing and high-power test of the first klystron prototype have been completed.When the gun operated at DC voltage of 80 k V and current of 15.4 A, the klystron peak power reached 804 k W with output efficiency of about 65.3% at 40% duty cycle. The 1-d B bandwidth is ±0.8 MHZ. Due to the crack of ceramic window, the CW power achieved about 700 kW. The high-power test results are in good agreement with 3D simulation.

A new method for measuring the pulse-front distortion of arbitrary shapes in high-power ultrashort laser systems

We present a new method that can be used to calculate pulse-front distortion by measuring the spectral interference of two point-diffraction fields in their overlapped district. We demonstrate, for the first time, the measurement of the pulse-front distortion of the pulse from a complex multi-pass amplification system, which exists in almost all high-power laser systems, and obtain the irregular pulse-front distribution. The method presented does not need any reference light or assumption about the pulse-front distribution, and has an accuracy of several femtoseconds.

Investigation on latch-up susceptibility induced by high-power microwave in complementary metal–oxide–semiconductor inverter

The latch-up effect induced by high-power microwave（HPM） in complementary metal–oxide–semiconductor（CMOS） inverter is investigated in simulation and theory in this paper. The physical mechanisms of excess carrier injection and HPM-induced latch-up are proposed. Analysis on upset characteristic under pulsed wave reveals increasing susceptibility under shorter-width pulsed wave which satisfies experimental data, and the dependence of upset threshold on pulse repetitive frequency（PRF） is believed to be due to the accumulation of excess carriers. Moreover, the trend that HPMinduced latch-up is more likely to happen in shallow-well device is proposed.Finally, the process of self-recovery which is ever-reported in experiment with its correlation with supply voltage and power level is elaborated, and the conclusions are consistent with reported experimental results.

High-Power Single-Spatial-Mode GaSb Tapered Laser around 2.0 μm with Very Small Lateral Beam Divergence

We report high-power single-spatial-mode type-I GaSb-based tapered lasers fabricated on the InGaSb/AlGaAsSb material system. A straight ridge and three different tapered waveguide structures with varying flare angles are fabricated to optimize the output power and spatial-mode performance. The best devices exhibit single-spatial-mode operation with room-temperature output power up to 350？mW in continuous-wave mode at an emission wavelength around 2.0？μm with a very small far-field lateral divergence angle, which is beyond state of the art in terms of single-spatial-mode output power.

Effect of the high-power electromagnetic pulses on the reactivity of the coal-water slurry in hot environment

An effect of the high-power electromagnetic pulses onto the droplet of coal-water slurry inside the furnace was investigated.In contrary to the previously investigated laser-induced fuel atomization that occurs at the room temperature,the pre-heated(to 400 K)slurry becomes dry enough to prevent the explosion-like steam formation.Thus,fuel does not atomize and the ignition does not accelerate.Furthermore,the absorption of several laser pulses leads to evident sintering of irradiated surface with following increase of the ignition delay time for up to 24%.Variation of the pulse energy in range 48-118 mJ(corresponding intensity up to 2.4 J·cm^-2)leads to certain variation of the increase of ignition delay.The strong pulsed overheating of the coal water slurry which does not initiate the fine atomization of the fuel generally makes its ignition longer.

Study on High-power LED Heat Dissipation Based on Printed Circuit Board

In order to study the role of printed circuit board(PCB)in high-power LED heat dissipation,a simple model of high-power LED lamp was designed.According to this lamp model,some thermal performances such as thermal resistances of four types of PCB and the changes of LED junction temperature were tested under three different working currents.The obtained results indicate that LED junction temperature can not be lowered significantly with the decreasing thermal resistance of PCB.However,PCB with low thermal resistance can be matched with smaller volume heat sink,so it is hopeful to reduce the size,weight and cost of LED lamp.

Organic electrode materials for fast-rate,high-power battery applications

The development of new battery materials with fast charging/discharging capabilities is necessary to meet the growing demands of modern technologies.While counter ion transport in inorganic materials(generally by de/intercalation)currently limits charge/discharge rates in lithium-ion batteries,the weak intermolecular forces in organic materials result in flexible,spacious structures that offer improved ion transport capabilities.Herein,we present the principles which enable fast rate capabilities in organic electrode materials,accompanied by specific literature examples illustrating exceptional rate performances.We discuss approaches to material design which support electron and/or ion transport and the limitations associated with each approach.This review aims to highlight the unique characteristics of organic materials as high-power density electrodes and inspire continued work in the field.

Research progresses on Cherenkov and transit-time high-power microwave sources at NUDT

Research progresses on Cherenkov and transit-time high-power microwave(HPM)sources in National University of Defense Technology(NUDT)of China are presented.The research issues are focused on the following aspects.The pulse-shortening phenomenon in O-type Cerenkov HPM devices is suppressed.The compact coaxial relativistic backward-wave oscillators(RBWOs)at low bands are developed.The power efficiency in M-Type HPM tubes without guiding magnetic field increased.The power capacities and power efficiencies in the triaxial klystron amplifier(TKA)and relativistic transit-time oscillator(TTO)at higher frequencies increased.In experiments,some exciting results were obtained.The X-band source generated 2 GW microwave power with a pulse duration of 110 ns in 30 Hz repetition mode.Both L-and P-band compact RBWOs generated over 2 GW microwave power with a power efficiency of over 30%.There is approximately a 75% decline of the volume compared with that of conventional RBWO under the same power capacity conditions.A 1.755 GHz MILO produced 3.1 GW microwave power with power efficiency of 10.4%.A 9.37 GHz TKA produced the 240 MW microwave power with the gain of 34 dB.A 14.3 GHz TTO produced 1 GW microwave power with power efficiency of 20%.

Elucidation of Metallic Plume and Spatter Characteristics Based on SVM During High-Power Disk Laser Welding

During deep penetration laser welding,there exist plume（weak plasma） and spatters,which are the results of weld material ejection due to strong laser heating.The characteristics of plume and spatters are related to welding stability and quality.Characteristics of metallic plume and spatters were investigated during high-power disk laser bead-on-plate welding of Type 304 austenitic stainless steel plates at a continuous wave laser power of 10 kW.An ultraviolet and visible sensitive high-speed camera was used to capture the metallic plume and spatter images.Plume area,laser beam path through the plume,swing angle,distance between laser beam focus and plume image centroid,abscissa of plume centroid and spatter numbers are defined as eigenvalues,and the weld bead width was used as a characteristic parameter that reflected welding stability.Welding status was distinguished by SVM（support vector machine） after data normalization and characteristic analysis.Also,PCA（principal components analysis） feature extraction was used to reduce the dimensions of feature space,and PSO（particle swarm optimization） was used to optimize the parameters of SVM.Finally a classification model based on SVM was established to estimate the weld bead width and welding stability.Experimental results show that the established algorithm based on SVM could effectively distinguish the variation of weld bead width,thus providing an experimental example of monitoring high-power disk laser welding quality.

High-Power Passively Q-Switched Nd:YAG Laser at 1112 nm with a Cr^(4+):YAG Saturable Absorber

A high-power passively Q-switched Nd：YAG laser operating at lll2nm with Cr4＋：yAO as a saturable absorber is demonstrated. Under 808 nm diode-direct pumping, the maximum average output power of 2.73 W is achieved at the pump power of 16.65 W, corresponding to an optical-to-optical conversion efficiency of 16.4%. At the same time, the pulse width, pulse repetition rate, single pulse energy and peak power are 27.2ns, 9 kHz, 303.3#3 and 11.2kW, respectively. As far as we know, the result gives the highest average output power at 1112nm generated by an 808 nm diode-end-pumped Nd：YAG laser.