Development of a Novel Parallel-spool Pilot Operated High-pressure Solenoid Valve with High Flow Rate and High Speed

High-pressure solenoid valve with high flow rate and high speed is a key component in an underwater driving system.However,traditional single spool pilot operated valve cannot meet the demands of both high flow rate and high speed simultaneously.A new structure for a high pressure solenoid valve is needed to meet the demand of the underwater driving system.A novel parallel-spool pilot operated high-pressure solenoid valve is proposed to overcome the drawback of the current single spool design.Mathematical models of the opening process and flow rate of the valve are established.Opening response time of the valve is subdivided into 4 parts to analyze the properties of the opening response.Corresponding formulas to solve 4 parts of the response time are derived.Key factors that influence the opening response time are analyzed.According to the mathematical model of the valve,a simulation of the opening process is carried out by MATLAB.Parameters are chosen based on theoretical analysis to design the test prototype of the new type of valve.Opening response time of the designed valve is tested by verifying response of the current in the coil and displacement of the main valve spool.The experimental results are in agreement with the simulated results,therefore the validity of the theoretical analysis is verified.Experimental opening response time of the valve is 48.3 ms at working pressure of 10 MPa.The flow capacity test shows that the largest effective area is 126 mm2 and the largest air flow rate is 2320 L/s.According to the result of the load driving test,the valve can meet the demands of the driving system.The proposed valve with parallel spools provides a new method for the design of a high-pressure valve with fast response and large flow rate.

Simulation research on dynamic performance of the new type high-pressure solenoid valve

To improve energy density,the transportation,storage,and operations of hydrogen,methane,and compressed air vehicles currently require high-pressure compression.High-pressure solenoid valve becomes the vital element to above system.In order to reduce leakage and aerodynamic force influence,a new type high-pressure solenoid valve was proposed.The simulation model which included electromagnetic model,aerodynamic force model was established by means of the nonlinear mathematic models.Using the software MATLAB/Simulink for simulation,the dynamic response characteristics of high-pressure pneumatic solenoid valve were obtained under different pulse width modulation(PWM)input control signals.Results show that,first of all,the new type of high-pressure solenoid valve can meet the switch requirement.Secondly,the opening movement and closing movement of the spool lags the PWM rising signal,and the coil current fluctuates significantly during the movement of the spool.Lastly,on/off status of high-pressure valve cannot be represented by the duty cycle.This research can be referred in the design of the high-pressure solenoid valve..

Seal contact performance analysis of soft seals on high-pressure hydrogen charge valves

The charge valve is an important element in the charging port of a high-pressure hydrogen storage cylinder(HP-HSC).It is normally closed after the HP-HSC is filled with hydrogen.If the seal of the charge valve is damaged,it will seriously affect the stable operation of the hydrogen supply system and may even cause safety problems.Therefore,the seal performance of the charge valve is important.In this paper,finite element analysis(FEA)is carried out to analyze the seal contact performance of hydrogenated nitrile rubber(HNBR)gaskets in the seal pair of a charge valve.The effects of different pre-compressions,seal widths,and hydrogen pressures on the seal contact performance of the charge valve are analyzed.The contact pressure on the seal surface increases with the increase of pre-compression.With a pre-compression of 2.5 mm,the maximum contact pressure without and with hydrogen pressure are 68.51 and 107.38 MPa,respectively.A contact gap appears in the inner ring of the seal surface with pre-compression below 0.15 mm.The contact gap occurs between the entire seal surface with a seal width of1 mm.The contact pressure on the seal surface and the width of the separation area between the seal surfaces increase with the increase of the seal width.The contact gap between the seal surfaces is zero with a width of 2.5 mm.The width of the separation area between the seal surfaces decreases with the decrease of the hydrogen pressure.The width of the separation area is reduced from 0.5 mm at 35 MPa to 0.17 mm at 15 MPa.This work can be useful for improvement of the seal performance and of the design of the charge valve used in the HP-HSC.