Development of a high-repetition-rate lumped-inductance kicker magnet prototype for the beam switchyard of SHINE

The Shanghai high-repetition-rate X-ray free-electron laser and extreme light facility(SHINE)operates at a maximum repetition rate of 1 MHz.Kicker magnets are key components that distribute electron bunches into three different undulator lines in a bunch-by-bunch mode.The kicker field width must be less than the time interval between bunches.A lumpedinductance kicker prototype was developed using a vacuum chamber with a single-turn coil.The full magnetic field strength was 0.005 T.This paper presents the requirements,design considerations,design parameters,magnetic field calculations,and measurements of the kicker magnets.The relevant experimental results are also presented.The pulse width of the magnetic field was approximately 600 ns,and the maximum operation repetition rate was 1 MHz.The developed kicker satisfies the requirements for the SHINE project.Finally,numerous recommendations for the future optimization of kicker magnets are provided.

High-repetition-rate seeded free-electron laser enhanced by self-modulation

The spectroscopic methods for the ultrafast electronic and structural dynamics of materials require fully coherent extreme ultraviolet and soft X-ray radiation with high-average brightness.Seeded free-electron lasers(FELs)are ideal sources for delivering fully coherent soft X-ray pulses.However,due to state-of-theart laser system limitations,it is challenging to meet the ultraviolet seed laser’s requirements of sufficient energy modulation and high repetition rates simultaneously.The self-modulation scheme has been proposed and recently demonstrated in a seeded FEL to relax the seed laser requirements.Using numerical simulations,we show that the required seed laser intensity in the self-modulation is~3 orders of magnitude lower than that in the standard high-gain harmonic generation(HGHG).The harmonic self-modulation can launch a singlestage HGHG FEL lasing at the 30th harmonic of the seed laser.Moreover,the proof-of-principle experimental results confirm that the harmonic self-modulation can still amplify the laser-induced energy modulation.These achievements reveal that the self-modulation can not only remarkably reduce the requirements of the seed laser but also improve the harmonic upconversion efficiency,which paves the way for realizing high-repetitionrate and fully coherent soft X-ray FELs.

High power diode-pumped passively mode-locked Nd:YVO_4 laser at repetition rate of 3.2 GHz

A compact high power diode-pumped passively mode-locked Nd:YVO_4 laser with high repetition rate is realized.Using an Nd:YVO_4 crystal and a semiconductor saturable absorber mirror(SESAM) in the oscillator, the picosecond pulse output with an average power of 1.38 W, a repetition rate of 3.24 GHz, and a pulse duration of 11.4 ps is achieved. After one stage of amplification, the final output power reaches 11.34 W, corresponding to a total optical-to-optical efficiency of about 32%. The root mean square(RMS) value of power fluctuation is demonstrated to be less than 0.6% in 24 hours,showing a superior stability with the compact configuration.

Effects of high temperature annealing and laser irradiation on activation rate of phosphorus

Thermal annealing and laser irradiation were used to study the activation rate of phosphorus in silicon after ion implantation.The activation rate refers to the ratio of activated impurity number to the total impurity number in the sample.After injecting phosphorus with the dose and energy(energy=55 keV,dose=3×10^(15) cm^(-2)),the samples were annealed at different temperatures,and laser irradiation experiments were performed after annealing.The experimental results showed that the activation rate of phosphorus was the highest at 850℃,and the highest activation rate was 67%.Upon femtosecond laser irradiation samples after thermal annealing,while keeping the crystalline silicon surface without damage,the activation rate was improved.When the energy-flux density of the femtosecond laser was 0.65 kJ/cm2,the activation rate was the highest,increasing from 67%to 74.81%.

Passive Q-Switching of a Yb:LuVO_4 Laser with Cr^(4+):YAG:Approaching the Intrinsic Upper Limit of Repetition Rate

We demonstrate a diode pumped Yb：LuVO4 laser that can be passively Q-switched by a Cr^（4＋）：YAG saturable absorber having an initial transmission as high as 99.3%.A maximum pulsed output power of 2.35 W is generated at a repetition rate of 285.7 kHz,approaching or very near the intrinsic upper limit imposed by the recovery time of the Cr^（4＋）：YAG saturable absorber,and the resulting pulse energy,duration and peak power are,respectively,8.2μJ,39.2ns and 0.209kW.

Erbium-Doped Zirconia-Alumina Silica Glass-Based Fiber as a Saturable Absorber for High Repetition Rate Q-Switched All-Fiber Laser Generation

We propose and demonstrate a Q-switched erbium-doped fiber laser （EDFL） using an erbium-doped zirconia-alumina silica glass-based fiber （Zr-EDF） as a saturable absorber. As a 16-cm-long Zr-EDF is incorporated into a ring EDFL cavity, a stable Q-switching pulse train operating at 1565？nm wavelength is successfully obtained. The repetition rate is tunable from 33.97？kHz to 71.23？kHz by increasing the pump power from the threshold of 26？mW to the maximum of 74？mW. The highest pulse energy of 26.67？nJ is obtained at the maximum pump power.

Generation of high-energy dual-wavelength domain wall pulse with low repetition rate in an HNLF-based fiber ring laser

The generation of high-energy dual-wavelength domain wall pulse with a low repetition rate is demonstrated in a highly nonlinear fiber （HNLF）-based fiber ring laser. By introducing the intracavity birefringence-induced spectral filtering effect, the dual-wavelength lasing operation can be achieved. In order to enhance the cross coupling effect between the two lasing beams for domain wall pulse formation, a 215-m HNLF is incorporated into the laser cavity. Experimentally, it is found that the dual-wavelength domain wall pulse with a repetition rate of 77.67 kHz could be efficiently obtained through simply rotating the polarization controller （PC）. At a maximum pump power of 322 mW, the 655-nJ single pulse energy in cavity is obtained. The proposed configuration provides a simpler and more efficient way to generate high energy pulse with a low repetition rate.

Dispersion relation and growth rate for a corrugated channel free-electron laser with a helical wiggler pump

The effects of corrugated ion channels on electron trajectories and spatial growth rate for a free-electron laser with a one-dimensional helical wiggler have been investigated. Analysis of the steady-state electron trajectories is performed by solving the equations of motion. Our results show that the presence of a corrugated channel shifts the resonance frequency to smaller values of ion channel frequency. The sixth-order dispersion equation describing the coupling between the electrostatic beam mode and the electromagnetic mode has also been derived. The dispersion relation characteristic is analyzed in detail by numerical solution. Results show that the growth rate of instability in the presence of corrugated ion channels can be greatly enhanced relative to the case of an uniform ion channel.

Science Letters:Controllable high repetition rate gain-switchedNd:YVO_4 microchip laser

We demonstrated a monolithic, compact, diode-pumped gain-switched Nd:YVO4 laser at 1.064 μm wavelength with controllable repetition rate of 1 Hz to 25 kHz. Stable gain-switched pulse train with maximum repetition rate of 25 kHz and pulse width of 16 ns was obtained.

Laser back scatter: Limitation to higher repetition rate [kHz] Satellite Laser Ranging system

Satellite laser ranging(SLR)with higher repetition rate is the recent trend for its various advantages.Laser backscatter(coincidence between recently transmitted pulses and received pulses near the detector)is found to be a constraint for the repetition rates higher than 20 kHz,due to,overlapping with photons returning from a satellite with the present constellation of most of the SLR systems.Such an overlap occurs at every 75 km satellite distance change at 2 kHz repetition rate,and remains for about 7.5 km;for a 20 kHz system however,it will occur after every 7.5 km and remains for 7.5 km,resulting in constant backscatter overlap e leaving no chance to avoid it.The resulting noise is 5 times more than before causing a serious problem in detection and lowers the signal to noise ratio of the overall SLR system.However,decreasing energy per shot at higher repetition rates e assuming a constant power laser e the resulting backscatter may decrease fractionally.

Fast repetition rate fs pulsed lasers for advanced PLIM microscopy

Simultaneous metabolic and oxygen imaging is promising to follow up therapy response,dis-ease development and to determine prognostic factors.FLIM of metabolic coenzymes is now widely accepted to be the most reliable method to determine cellular bioenergetics.Also,oxygen consumption has to be taken into account to understand treatment responses.The phosphorescence lifetimne of oxygen sensors is able to indicate local oxygen changes.For phosphorescence lifetime imaging(PLIM)dyes based on ruthenium(I)coordination com-plexes are useful,in detaill TLD1433 which possesses a variety of different triplet states,enables complex photochemistry and redox reactions.PLIM is usally reached by two photon exci-tation of the drug with a femtosecond(fs)pulsed Ti:Sapphire laser working at 80 MHz repe-tition rate and(time-correlated single photon counting)(TCSPC)detection electronics.The interesting question was whether it is possible to follow up PLIM 1using faster repetition rates.Faster repetition rates could be advantageous for the induction of specific photochemical reactions because of similar light doses used normally in standard CW light treatments.For this,a default 2p-FLIM-PLIM system was expanded by adding a second fs pulsed laser("helixx")which provides 50 fs pulses at a repetition rate of 250 MHz,more than 2.3 w average power and tunable from 720 nm to 920 nm.The laser beam was coupled into the AOM instead of the default 80 MHz laser.We demonstrated siuccessful applications of the 250 MHz laser for PLIM which correlates well with measurements done by excitation with the conventional 80MHx laser source.

Cooling rate calibration and mapping of ultra-short pulsed laser modifications in fused silica by Raman and Brillouin spectroscopy

This paper focuses on the preparation of a new extended set of calibrations of cooling rate(fictive temperature)in fused silica determined by inelastic light scattering and its subsequent use to characterize the local cooling rate distribution in ultra-short pulsed(USP)laser modification.In order to determine the thermal history(e.g.cooling rate and fictive temperature)of fused silica,high-resolution inelastic light-scattering experiments(Raman and Brillouin spectroscopy)were investigated.Calibrations were performed and compared to the existing literature to quantify structural changes due to a change of fictive temperature.Compared to existing calibrations,this paper provides an extension to lower and higher cooling rates.Using this new set of calibrations,we characterized a USP laser modification in fused silica and calculated the local fictive temperature distribution.An equation relating the fictive temperature(Tf)to cooling rates is given.A maximum cooling rate of 3000 K min-1 in the glass transition region around 1200℃ was deduced from the Raman analysis.The Brillouin observations are sensitive to both the thermal history and the residual stress.By comparing the Raman and Brillouin observations,we extracted the local residual stress distribution with high spatial resolution.For the first time,combined Raman and Brillouin inelastic light scattering experiments show the local distribution of cooling rates and residual stresses(detailed behavior of the glass structure)in the interior and the surrounding of an USP laser modified zone.

Experimental Study of Buffer Gas Flow Rate Effect on Output Power of a Copper Vapor Laser

A copper vapor laser with active medium length of 60 cm and bore of 16 mm has been operated and optimized using different buffer gases to investigate the effect of the gas flow rates on the output power. It is found that there is a special optimum gas flow rate associated with the type of buffer gas.

High-rate metal-free MXene microsupercapacitors on paper substrates

MXene is a promising energy storage material for miniaturized microbatteries and microsupercapacitors(MSCs).Despite its superior electrochemical performance,only a few studies have reported MXene-based ultrahigh-rate(>1000 mV s^(−1))on-paper MSCs,mainly due to the reduced electrical conductance of MXene films deposited on paper.Herein,ultrahigh-rate metal-free on-paper MSCs based on heterogeneous MXene/poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate)(PEDOT:PSS)-stack electrodes are fabricated through the combination of direct ink writing and femtosecond laser scribing.With a footprint area of only 20 mm^(2),the on-paper MSCs exhibit excellent high-rate capacitive behavior with an areal capacitance of 5.7 mF cm^(−2)and long cycle life(>95%capacitance retention after 10,000 cycles)at a high scan rate of 1000 mV s^(−1),outperforming most of the present on-paper MSCs.Furthermore,the heterogeneous MXene/PEDOT:PSS electrodes can interconnect individual MSCs into metal-free on-paper MSC arrays,which can also be simultaneously charged/discharged at 1000 mV s^(−1),showing scalable capacitive performance.The heterogeneous MXene/PEDOT:PSS stacks are a promising electrode structure for on-paper MSCs to serve as ultrafast miniaturized energy storage components for emerging paper electronics.

Segregation of niobium in laser cladding Inconel 718 superalloy

Inconel 718 superalloy is widely used in the aerospace and turbine industry. Segregation of niobium appears in the laser cladding Inconel 718 superalloy and consequently influences the phase transformation during the rapid solidification. In order to control the microstructure and improve the mechanical properties of the deposited coating, the the influence of solidification conditions on the segregation of niobium and the resultant formation of Nb-rich Laves phase was studied using the microstructure observation and EDS analysis. The results show that the cooling rate has considerable influence on the microstructure of the deposited coating. High cooling rate is beneficial for suppressing the segregation of Nb and reducing the formation of Laves phase, which is believed to be detrimental to the performance of the Inconel 718 alloy.

Heavy-ion and pulsed-laser single event effects in 130-nm CMOS-based thin/thick gate oxide anti-fuse PROMs

Single event effects of 1-T structure programmable read-only memory(PROM) devices fabricated with a 130-nm complementary metal oxide semiconductorbased thin/thick gate oxide anti-fuse process were investigated using heavy ions and a picosecond pulsed laser. The cross sections of a single event upset(SEU) for radiationhardened PROMs were measured using a linear energy transfer(LET) ranging from 9.2 to 95.6 MeV cm^2mg^(-1).The result indicated that the LET threshold for a dynamic bit upset was ～ 9 MeV cm^2mg^(-1), which was lower than the threshold of ～ 20 MeV cm^2mg^(-1) for an address counter upset owing to the additional triple modular redundancy structure present in the latch. In addition, a slight hard error was observed in the anti-fuse structure when employing209 Bi ions with extremely high LET values(～ 91.6 MeV cm^2mg^(-1)) and large ion fluence(～ 1×10~8 ions cm^(-2)). To identify the detailed sensitive position of a SEU in PROMs, a pulsed laser with a 5-μm beam spot was used to scan the entire surface of the device.This revealed that the upset occurred in the peripheral circuits of the internal power source and I/O pairs rather than in the internal latches and buffers. This was subsequently confirmed by a ^(181)Ta experiment. Based on the experimental data and a rectangular parallelepiped model of the sensitive volume, the space error rates for the used PROMs were calculated using the CRèME-96 prediction tool. The results showed that this type of PROM was suitable for specific space applications, even in the geosynchronous orbit.

Characteristic of laser-MIG hybrid welding with filling additional cold wire for aluminum alloy

The weld appearance, deposition rate, welding efficiency, stability of arc, laser keyhole characteristic, and weld property were studied by using a novel laser-MIG hybrid welding process with filling wire of aluminum alloy. The results were also compared with those by conventional laser-MIG hybrid welding process. It was found that with the suitable process parameters this novel welding process for aluminum alloy was stable and final weld bead had fine appearance. Compared to conventional laser-MIG hybrid welding process, during this novel welding process the stability of arc, the laser keyhole characteristic and the weld property were similar, while the keyhole cycle frequency and keyhole opening area had differences of 1.23% and 15.34%, respectively, and the welding efficiency increased by about 31% without increasing heat input.

227-W output all-fiberized Tm-doped fiber laser at 1908 nm

In this paper, we report that a diode-pumped thulium-doped double clad silica fiber laser can provide powers of up to 227 W at 1908 nm, corresponding to a slope efficiency of 54.3%, and an optical-to-optical efficiency of 51.2%. The output power, to the best of our knowledge, is the highest output at 1908 nm. The beam quality M2 factor is about 1.56. Also discussed in this paper is the dependence of the laser performance on fiber length.

A Study on Super Speed Forming of Metal Sheet by Laser Shock Waves

Metal sheet plastic deformation or forming is gener at ed through a mechanical pressure or a thermal variation. These pressure variatio ns or thermal variations can be created by a variety of means such as press form ing, hydroforming, imploding detonation and so on. According to the magnitude of the strain rates all these forming methods can be divided into quasi-static fo rming and dynamical forming. Up to now there are no reports of forming methods w ith the strain rates above 10 5sec -1, even though the exploding forming. In this article, we work on a dynamic super-speed forming method driven by lase r shock waves and advanced a novel concept of laser shock forming. The initial o bservation of the laser shock forming is done through a bugle testing with speci mens of SUS430 sheet metal, using a neodymium-glass laser of pulse energy 10J～ 3 0J and duration of 20 ns (FWHM). The investigation revealed that the plastic de formation during the laser shock forming is characterized as ultrahigh strain ra te up to 10 7sec -1. We indicate that plastic deformation increases nonlin early when the energy density of the laser varies. By investigating the hardness and residual stress of the surfaces, we conclude that laser shock forming is a combination technique of laser shock strengthening and metal forming for introdu cing a strain harden and a compressive residual stress on the surface of the wor k-piece, and the treated surface by laser shock forming has good properties in fatigue and corrosion resistance. This technique can achieve forming wit h or without mould.

Theoretical study and optimization of a high power mid-infrared erbium-doped ZBLAN fibre laser

Based on the rate equations describing the erbium-doped fluoride glass （ZBLAN） fibre lasers with different pumping configurations being taken into account, this paper presents theoretical calculations related to the dynamic population density and the operation performance of a high power mid-infrared all-fibre erbium-doped ZBLAN fibre laser. It shows that the ground-state absorption, excited-state absorption and energy-transfer-upconversion processes co-exist and produce a population balance, causing the laser to operate stably at a continuous wave state. A good agreement between the theoretical results and recent experimental measurement is obtained. Furthermore, the laser structure parameters including fibre length, reflectance of output fibre Bragg grating and pumping configurations are quantitatively optimised to achieve the best performance. The results show, as expected, that the slope efficiency of the fibre laser can be improved significantly through optimisation, which then provides an important guide for the design of high-performance mid-infrared erbium-doped ZBLAN fibre lasers.