The interleaving/multiplexing technique was used to realize a 200?MHz real time data acquisition system. Two 100?MHz ADC modules worked parallelly and every ADC plays out data in ping pang fashion. The design improv...The interleaving/multiplexing technique was used to realize a 200?MHz real time data acquisition system. Two 100?MHz ADC modules worked parallelly and every ADC plays out data in ping pang fashion. The design improved the system conversion rata to 200?MHz and reduced the speed of data transporting and storing to 50?MHz. The high speed HDPLD and ECL logic parts were used to control system timing and the memory address. The multi layer print board and the shield were used to decrease interference produced by the high speed circuit. The system timing was designed carefully. The interleaving/multiplexing technique could improve the system conversion rata greatly while reducing the speed of external digital interfaces greatly. The design resolved the difficulties in high speed system effectively. The experiment proved the data acquisition system is stable and accurate.展开更多
Digital to analog converters(DAC)play an important role as a bridge connecting the analog world and the digital world.With the rapid development of wireless communication,wideband digital radar,and other emerging tech...Digital to analog converters(DAC)play an important role as a bridge connecting the analog world and the digital world.With the rapid development of wireless communication,wideband digital radar,and other emerging technologies,better performing high-speed high-resolution DACs are required.In those applications,signal bandwidth and high-frequency linearity often limited by data converters are the bottleneck of the system.This article reviews the state-of-the-art technologies of high-speed and high-resolution DACs reported in recent years.Comparisons are made between different architectures,circuit implementations and calibration techniques along with the figure of merit(FoM)results.展开更多
为降低流水线模数转换器(ADC)中跨导运算放大器(OTA)设计要求,在分析已有开关电容电路(SC)误差消除技术和流水线ADC误差源的基础上,提出一种改进的流水线ADC开关电容电路及与其匹配的OTA设计方案。采用交叉差分结构,对虚地电容进行了修...为降低流水线模数转换器(ADC)中跨导运算放大器(OTA)设计要求,在分析已有开关电容电路(SC)误差消除技术和流水线ADC误差源的基础上,提出一种改进的流水线ADC开关电容电路及与其匹配的OTA设计方案。采用交叉差分结构,对虚地电容进行了修正,并将电容失配参数在系统传输函数中消去,使开关电容电路对OTA的增益误差要求降低,并使其瞬态功耗下降。采用CM O S 0.18μm工艺设计了一个分辨率为8位、取样速率200 MH z的ADC作为验证原型,仿真结果表明,该优化结构符合ADC电路高速低功耗要求,可作为信号前端处理模块应用到模数转换电路中。展开更多
文摘The interleaving/multiplexing technique was used to realize a 200?MHz real time data acquisition system. Two 100?MHz ADC modules worked parallelly and every ADC plays out data in ping pang fashion. The design improved the system conversion rata to 200?MHz and reduced the speed of data transporting and storing to 50?MHz. The high speed HDPLD and ECL logic parts were used to control system timing and the memory address. The multi layer print board and the shield were used to decrease interference produced by the high speed circuit. The system timing was designed carefully. The interleaving/multiplexing technique could improve the system conversion rata greatly while reducing the speed of external digital interfaces greatly. The design resolved the difficulties in high speed system effectively. The experiment proved the data acquisition system is stable and accurate.
文摘Digital to analog converters(DAC)play an important role as a bridge connecting the analog world and the digital world.With the rapid development of wireless communication,wideband digital radar,and other emerging technologies,better performing high-speed high-resolution DACs are required.In those applications,signal bandwidth and high-frequency linearity often limited by data converters are the bottleneck of the system.This article reviews the state-of-the-art technologies of high-speed and high-resolution DACs reported in recent years.Comparisons are made between different architectures,circuit implementations and calibration techniques along with the figure of merit(FoM)results.
文摘为降低流水线模数转换器(ADC)中跨导运算放大器(OTA)设计要求,在分析已有开关电容电路(SC)误差消除技术和流水线ADC误差源的基础上,提出一种改进的流水线ADC开关电容电路及与其匹配的OTA设计方案。采用交叉差分结构,对虚地电容进行了修正,并将电容失配参数在系统传输函数中消去,使开关电容电路对OTA的增益误差要求降低,并使其瞬态功耗下降。采用CM O S 0.18μm工艺设计了一个分辨率为8位、取样速率200 MH z的ADC作为验证原型,仿真结果表明,该优化结构符合ADC电路高速低功耗要求,可作为信号前端处理模块应用到模数转换电路中。
