High-SpeedReal-TimeDataAcquisitionSystem Realized by Interleaving/Multiplexing Technique

The interleaving/multiplexing technique was used to realize a 200?MHz real time data acquisition system. Two 100?MHz ADC modules worked parallelly and every ADC plays out data in ping pang fashion. The design improved the system conversion rata to 200?MHz and reduced the speed of data transporting and storing to 50?MHz. The high speed HDPLD and ECL logic parts were used to control system timing and the memory address. The multi layer print board and the shield were used to decrease interference produced by the high speed circuit. The system timing was designed carefully. The interleaving/multiplexing technique could improve the system conversion rata greatly while reducing the speed of external digital interfaces greatly. The design resolved the difficulties in high speed system effectively. The experiment proved the data acquisition system is stable and accurate.

High-speed broadband data acquisition system based on FPGA

A field-programmable gate array(FPGA)based high-speed broadband data acquisition system is designed.The system has a dual channel simultaneous acquisition function.The maximum sampling rate is 500 MSa/s and bandwidth is200 MHz,which solves the large bandwidth,high-speed signal acquisition and processing problems.At present,the data acquisition system is successfully used in broadband receiver test systems.

Reliable Data Collection Model and Transmission Framework in Large-Scale Wireless Medical Sensor Networks

Large-scale wireless sensor networks(WSNs)play a critical role in monitoring dangerous scenarios and responding to medical emergencies.However,the inherent instability and error-prone nature of wireless links present significant challenges,necessitating efficient data collection and reliable transmission services.This paper addresses the limitations of existing data transmission and recovery protocols by proposing a systematic end-to-end design tailored for medical event-driven cluster-based large-scale WSNs.The primary goal is to enhance the reliability of data collection and transmission services,ensuring a comprehensive and practical approach.Our approach focuses on refining the hop-count-based routing scheme to achieve fairness in forwarding reliability.Additionally,it emphasizes reliable data collection within clusters and establishes robust data transmission over multiple hops.These systematic improvements are designed to optimize the overall performance of the WSN in real-world scenarios.Simulation results of the proposed protocol validate its exceptional performance compared to other prominent data transmission schemes.The evaluation spans varying sensor densities,wireless channel conditions,and packet transmission rates,showcasing the protocol’s superiority in ensuring reliable and efficient data transfer.Our systematic end-to-end design successfully addresses the challenges posed by the instability of wireless links in large-scaleWSNs.By prioritizing fairness,reliability,and efficiency,the proposed protocol demonstrates its efficacy in enhancing data collection and transmission services,thereby offering a valuable contribution to the field of medical event-drivenWSNs.

Flight Time Minimization of UAV for Cooperative Data Collection in Probabilistic LoS Channel

This paper investigates the data collection in an unmanned aerial vehicle(UAV)-aided Internet of Things(IoT) network, where a UAV is dispatched to collect data from ground sensors in a practical and accurate probabilistic line-of-sight(LoS) channel. Especially, access points(APs) are introduced to collect data from some sensors in the unlicensed band to improve data collection efficiency. We formulate a mixed-integer non-convex optimization problem to minimize the UAV flight time by jointly designing the UAV 3D trajectory and sensors’ scheduling, while ensuring the required amount of data can be collected under the limited UAV energy. To solve this nonconvex problem, we recast the objective problem into a tractable form. Then, the problem is further divided into several sub-problems to solve iteratively, and the successive convex approximation(SCA) scheme is applied to solve each non-convex subproblem. Finally,the bisection search is adopted to speed up the searching for the minimum UAV flight time. Simulation results verify that the UAV flight time can be shortened by the proposed method effectively.

Actor-Critic-Based UAV-Assisted Data Collection in the Wireless Sensor Network

Wireless Sensor Network(WSN)is widely utilized in large-scale distributed unmanned detection scenarios due to its low cost and flexible installation.However,WSN data collection encounters challenges in scenarios lacking communication infrastructure.Unmanned aerial vehicle(UAV)offers a novel solution for WSN data collection,leveraging their high mobility.In this paper,we present an efficient UAV-assisted data collection algorithm aimed at minimizing the overall power consumption of the WSN.Firstly,a two-layer UAV-assisted data collection model is introduced,including the ground and aerial layers.The ground layer senses the environmental data by the cluster members(CMs),and the CMs transmit the data to the cluster heads(CHs),which forward the collected data to the UAVs.The aerial network layer consists of multiple UAVs that collect,store,and forward data from the CHs to the data center for analysis.Secondly,an improved clustering algorithm based on K-Means++is proposed to optimize the number and locations of CHs.Moreover,an Actor-Critic based algorithm is introduced to optimize the UAV deployment and the association with CHs.Finally,simulation results verify the effectiveness of the proposed algorithms.

If real-time route and high-speed data is important,GoTa is vital.

GoTaTM from ZTE is the world’s first CDMA-based system. Now, ZTE proudly introduces its third-generation digital trunking system featuring a centralized dispatch,

If real-time route and high-speed data is important, GoTa is vital.

GoTa TM from ZTE is the world’s first CDMA-based system. Now, ZTE proudly introduces its third-generation digital trunking system featuring

If real-time route and high-speed data is important, GoTa is vital.

Go Tafrom ZTE is the world’s first CDMA-based system. Now, ZTE proudly introduces its third-generation digital trunking system featuring a centralized dispatch,

A power-quality monitoring and assessment system for high-speed railways based on train-network-data center integration

In recent years,with the rapid development of high-speed railways(HSRs),power interruptions or disturbances in traction power supply systems have become increasingly dangerous.However,it is often impossible to detect these faults immediately through single-point monitoring or collecting data after accidents.To coordinate the power quality data of both traction power supply systems(TPSSs)and high-speed trains(HSTs),a monitoring and assessing system is proposed to access the power quality issues on HSRs.By integrating train monitoring,traction substation monitoring and data center,this monitoring system not only realizes the real-time monitoring of operational behaviors for both TPSSs and HSTs,but also conducts a comprehensive assessment of operational quality for train-network systems.Based on a large number of monitoring data,the field measurements show that this real-time monitoring system is effective for monitoring and evaluating a traction-network system.

A Modified Generative Adversarial Network for Fault Diagnosis in High-Speed Train Components with Imbalanced and Heterogeneous Monitoring Data

Data-driven methods are widely considered for fault diagnosis in complex systems.However,in practice,the between-class imbalance due to limited faulty samples may deteriorate their classification performance.To address this issue,synthetic minority methods for enhancing data have been proved to be effective in many applications.Generative adversarial networks(GANs),capable of automatic features extraction,can also be adopted for augmenting the faulty samples.However,the monitoring data of a complex system may include not only continuous signals but also discrete/categorical signals.Since the current GAN methods still have some challenges in handling such heterogeneous monitoring data,a Mixed Dual Discriminator GAN(noted as M-D2GAN)is proposed in this work.In order to render the expanded fault samples more aligned with the real situation and improve the accuracy and robustness of the fault diagnosis model,different types of variables are generated in different ways,including floating-point,integer,categorical,and hierarchical.For effectively considering the class imbalance problem,proper modifications are made to the GAN model,where a normal class discriminator is added.A practical case study concerning the braking system of a high-speed train is carried out to verify the effectiveness of the proposed framework.Compared to the classic GAN,the proposed framework achieves better results with respect to F-measure and G-mean metrics.

Design of high-speed signal acquisition system and analysis of signal integrity

The device is used for the test on the fuze detonating time according to the initial velocity of the projectile and the altitude and speed of enemy aircraft flight. For the special requirements of the high-speed signal acquisition in the process, the characteristics of the measured signal are analyzed. The system is investigated in chip selection, signal transmission, signal processing, signal storage, post-production PCB design, etc. The appropriate measures and solutions which affect the integrity and accuracy of the signal in each process are proposed. The rules for the layout of the device and wiring are made. The result show that the measurement values are accurate without loss of data.

Research on the Remote Data Collection Based SQL Server

The remote data collection system based on SOL Server database technology was developed by Visual C++and SQL Server database technology together.The Client/Server mode was adopted.The system adopted the database search technologi- cal-ADO to work out the communication procedure of the server.And the old data of corresponding memory units were upgraded by the new data which gathered from PLC through serial port real time in the database.The Client utilizes the network technology and database technology through queries procedure to access the data information in the database.Thus a large number of relevant data that the production line operated were obtained.The goal of understanding operation conditions of product line was achieved through analysis of these data.This system has been debugged by the experiment successfully.

New design for multi-crystal data collection at SSRF

Data collection with microcrystals at synchrotron radiation facilities is challenging because it is difficult to harvest and locate microcrystals. Moreover,microcrystals are sensitive to radiation damage; thus, typically, a complete data set cannot be obtained with a single microcrystal. Herein, we report a new method for data collection with multiple microcrystals having a crystal size ranging from 1 to 30 lm. This method is suitable for not only low-temperature(100 K) data collection but also room-temperature data collection. Thin Kapton membranes were used to capture multiple crystals simultaneously. The microcrystals were visible under an optical microscope and easily located because the membrane was transparent and sufficiently thin. The film was fixed to a bracket that was prepared using a three-dimensional printer. The bracket was fixed on a magnetic base via screwing and employed by the goniometer system for data collection. Multiple data sets of fatty acid-binding protein 4(FABP4) and lysozyme microcrystals were collected using this novel designed device. Finally, the structures of protein FABP4 and lysozyme were obtained from these data via the molecule replacement method. The data statistics reveal that this method provides a comparable result to traditional methods such as a nylon loop.

An Optimal Feed Interpolator Based on G^2 Continuous Bézier Curves for High-Speed Machining of Linear Tool Path

A numerical control (NC) tool path of digital CAD model is widely generated as a set of short line segments in machining. However, there are three shortcomings in the linear tool path, such as discontinuities of tangency and curvature, huge number of line segments, and short lengths of line segments. These disadvantages hinder the development of high speed machining. To smooth the linear tool path and improve machining efficiency of short line segments, this paper presents an optimal feed interpolator based on G^2 continuous Bézier curves for the linear tool path. First, the areas suitable for fitting are screened out based on the geometric characteristics of continuous short segments (CSSs). CSSs in every area are compressed and fitted into a G^2 Continuous Bézier curve by using the least square method. Then a series of cubic Bézier curves are generated. However, the junction between adjacent Bézier curves is only G^0 continuous. By adjusting the control points and inserting Bézier transition curves between adjacent Bézier curves, the G^2 continuous tool path is constructed. The fitting error is estimated by the second-order Taylor formula. Without iteration, the fitting algorithm can be implemented in real-time environment. Second, the optimal feed interpolator considering the comprehensive constraints (such as the chord error constraint, the maximum normal acceleration, servo capacity of each axis, etc.) is proposed. Simulation and experiment are conducted. The results shows that the proposed method can generate smooth path, decrease the amount of segments and reduce machining time for machining of linear tool path. The proposed research provides an effective method for high-speed machining of complex 2-D/3-D profiles described by short line segments.

HOTCAP:a new software package for high-speed oscilloscopebased three-dimensional bunch charge and position measurement

A software package to be used in high-speed oscilloscope-basedthree-dimensionalbunch-by-bunch charge and position measurement is presented.The software package takes the pick-up electrode signal waveform recorded by the high-speed oscilloscope as input,and it calculates and outputs the bunch-by-bunch charge and position.In addition to enabling a three-dimensional observation of the motion of each passing bunch on all beam position monitor pick-up electrodes,it offers many additional features such as injection analysis,bunch response function reconstruction,and turn-by-turn beam analysis.The software package has an easy-to-understand graphical user interface and convenient interactive operation,which has been verified on the Windows 10 system.

Evaluation of the Accuracy and Automation of Travel Time and Delay Data Collection Methods

Travel time and delay are among the most important measures for gauging a transportation system’s performance. To address the growing problem of congestion in the US, transportation planning legislation mandated the monitoring and analysis of system performance and produced a renewed interest in travel time and delay studies. The use of traditional sensors installed on major roads (e.g. inductive loops) for collecting data is necessary but not sufficient because of their limited coverage and expensive costs for setting up and maintaining the required infrastructure. The GPS-based techniques employed by the University of Delaware have evolved into an automated system, which provides more realistic experience of a traffic flow throughout the road links. However, human error and the weaknesses of using GPS devices in urban settings still have the potential to create inaccuracies. By simultaneously collecting data using three different techniques, the accuracy of the GPS positioning data and the resulting travel time and delay values could be objectively compared for automation and statistically compared for accuracy. It was found that the new technique provided the greatest automation requiring minimal attention of the data collectors and automatically processing the data sets. The data samples were statistically analyzed by using a combination of parametric and nonparametric statistical tests. This analysis greatly favored the GeoStats GPS method over the rest methods.

Web-based GIS System for Real-time Field Data Collection Using Personal Mobile Phone

Recently, use of mobile communicational devices in field data collection is increasing such as smart phones and cellular phones due to emergence of embedded Global Position System GPS and Wi-Fi Internet access. Accurate timely and handy field data collection is required for disaster management and emergency quick responses. In this article, we introduce web-based GIS system to collect the field data by personal mobile phone through Post Office Protocol POP3 mail server. The main objective of this work is to demonstrate real-time field data collection method to the students using their mobile phone to collect field data by timely and handy manners, either individual or group survey in local or global scale research.

Energy Aware Data Collection with Route Planning for 6G Enabled UAV Communication

With technological advancements in 6G and Internet of Things(IoT), the incorporation of Unmanned Aerial Vehicles (UAVs) and cellularnetworks has become a hot research topic. At present, the proficient evolution of 6G networks allows the UAVs to offer cost-effective and timelysolutions for real-time applications such as medicine, tracking, surveillance,etc. Energy efficiency, data collection, and route planning are crucial processesto improve the network communication. These processes are highly difficultowing to high mobility, presence of non-stationary links, dynamic topology,and energy-restricted UAVs. With this motivation, the current research paperpresents a novel Energy Aware Data Collection with Routing Planning for6G-enabled UAV communication (EADCRP-6G) technique. The goal of theproposed EADCRP-6G technique is to conduct energy-efficient cluster-baseddata collection and optimal route planning for 6G-enabled UAV networks.EADCRP-6G technique deploys Improved Red Deer Algorithm-based Clustering (IRDAC) technique to elect an optimal set of Cluster Heads (CH) andorganize these clusters. Besides, Artificial Fish Swarm-based Route Planning(AFSRP) technique is applied to choose an optimum set of routes for UAVcommunication in 6G networks. In order to validated whether the proposedEADCRP-6G technique enhances the performance, a series of simulationswas performed and the outcomes were investigated under different dimensions.The experimental results showcase that the proposed model outperformed allother existing models under different evaluation parameters.

Energy-Efficient Underwater Data Collection:A Q-Learning Based Approach

Underwater data collection is an importance part in the process of network monitoring,network management and intrusion detection.However,the limited-energy of nodes is a major challenge to collect underwater data.The solution of this problem are not only in the hands of network topology but in the hands of path of autonomous underwater vehicle(AUV).With the problem in hand,an energy-efficient data collection scheme is designed for mobile underwater network.Especially,the data collection scheme is divided into two phases,i.e.,routing algorithm design for sensor nodes and path planing for AUV.With consideration of limited-energy and network robustness,Q-learning based dynamic routing algorithm is designed in the first phase to optimize the routing selection of nodes,through which a potential-game based optimal rigid graph method is proposed to balance the trade-off between the energy consumption and the network robustness.With the collected data,Q-learning based path planning strategy is proposed for AUV in the second phase to find the desired path to gather the data from data collector,then a mode-free tracking controller is developed to track the desired path accurately.Finally,the performance analysis and simulation results reveal that the proposed approach can guarantee energy-efficient and improve network stability.

NOMA Empowered Energy Efficient Data Collection and Wireless Power Transfer in Space-Air-Ground Integrated Networks

As the sixth generation network(6G)emerges,the Internet of remote things(IoRT)has become a critical issue.However,conventional terrestrial networks cannot meet the delay-sensitive data collection needs of IoRT networks,and the Space-Air-Ground integrated network(SAGIN)holds promise.We propose a novel setup that integrates non-orthogonal multiple access(NOMA)and wireless power transfer(WPT)to collect latency-sensitive data from IoRT networks.To extend the lifetime of devices,we aim to minimize the maximum energy consumption among all IoRT devices.Due to the coupling between variables,the resulting problem is non-convex.We first decouple the variables and split the original problem into four subproblems.Then,we propose an iterative algorithm to solve the corresponding subproblems based on successive convex approximation(SCA)techniques and slack variables.Finally,simulation results show that the NOMA strategy has a tremendous advantage over the OMA scheme in terms of network lifetime and energy efficiency,providing valuable insights.