Influence of high-speed milling parameter on 3D surface topography and fatigue behavior of TB6 titanium alloy

High-speed milling of titanium alloys is widely used in aviation and aerospace industries for its high efficiency and good quality.In order to optimize the machining parameters in high-speed milling TB6 titanium alloy,experiments of high-speed milling and fatigue were conducted to investigate the effect of parameters on 3D surface topography and fatigue life.Based on the fatigue fracture,the effect mechanism of surface topography on the fatigue crack initiation was proposed.The experiment results show that when the milling speed ranged from 100 m/min to 140 m/min,and the feed per tooth ranged from 0.02 mm/z to 0.06 mm/z,the obtained surface roughness were within the limit（0.8 μm）.Fatigue life decreased sharply with the increase of surface equivalent stress concentration factor.The average error of fatigue life between the established model and the experimental results was 6.25%.The fatigue cracks nucleated at the intersection edge of machined surface.

TOOL WEAR PATTERNS AND MECHANISMS OF SOLID CEMENTED CARBIDE IN HIGH-SPEED MILLING OF ALUMINUM ALLOY

The wear patterns and wear mechanisms of solid cemented carbide are analyzed in high-speed milling of aluminum alloy. Results show that the dominant wear patterns are coating damage, crater wear, micro-chipping, breakage, and so on. The main wear mechanisms are adhesion, diffusion and fatigue. Compared with conventional speed machining, the effect and impact of thermal-dynamical coupling field play an important role in the cutting tool wear in high-speed milling of aluminum alloy.

MACHINING-FEATURE BASED 3-AXIS AUTOMATIC NC PROGRAMMING FOR HIGH-SPEED MILLING

Machining-features of the workplace are described by using of the object-oriented （O-O） technology. Geometrical machining-features are recognized in the given cut region by using the maximum membership priciple about the fuzzy set. Depending on the IF-THEN rule and the fuzzy matching method, the rough information of the machining-process for high-speed milling （HSM） is extracted based on the database of machining-process for HSM. The optimization model of machining-process scheme is established to obtain shorter cut time, lower cost or higher surface quality. It is helpful to form successful cases for HSM. NC programming for HSM is realized according to optimized machining-process data from HSM cases selected by the optimization model and the extracted information of machining-process.

Extraction Fuzzy Linguistic Rules from Neural Networks for Maximizing Tool Life in High-speed Milling Process

In metal cutting industry it is a common practice to search for optimal combination of cutting parameters in order to maximize the tool life for a fixed minimum value of material removal rate（MRR）. After the advent of high-speed milling（HSM） pro cess, lots of experimental and theoretical researches have been done for this purpose which mainly emphasized on the optimization of the cutting parameters. It is highly beneficial to convert raw data into a comprehensive knowledge-based expert system using fuzzy logic as the reasoning mechanism. In this paper an attempt has been presented for the extraction of the rules from fuzzy neural network（FNN） so as to have the most effective knowledge-base for given set of data. Experiments were conducted to determine the best values of cutting speeds that can maximize tool life for different combinations of input parameters. A fuzzy neural network was constructed based on the fuzzification of input parameters and the cutting speed. After training process, raw rule sets were extracted and a rule pruning approach was proposed to obtain concise linguistic rules. The estimation process with fuzzy inference showed that the optimized combination of fuzzy rules provided the estimation error of only 6.34 m/min as compared to 314 m/min of that of randomized combination of rule s.

Influence of High-Speed Milling Process on Mechanical and Microstructural Properties of Ultrafine Grained Profiles Produced by Linear Flow Splitting

The effects of milling parameters on the surface quality,microstructures and mechanical properties of machined parts with ultrafine grained(UFG)gradient microstructures are investigated.The effects of the cutting speed,feed per tooth,cutting tool geometry and cooling strategy are demonstrated.It has been found that the surface quality of machined grooves can be improved by increasing the cutting speed.However,cryogenic cooling with CO_2 exhibits no significant improvement of surface quality.Microstructure and hardness investigations revealed similar microstructure and hardness variations near the machined groove walls for both utilized tool geometries.Therefore,cryogenic cooling can decrease more far-ranging hardness reductions due to high process temperatures,especially in the UFG regions of the machined parts,whilst it cannot prevent the drop in hardness directly at the groove walls.

NOVEL METHOD FOR DYNAMIC OPTIMIZATION OF STABILITY IN HIGH-SPEED MILLING SYSTEM

Considering the self-excited and forced vibrations in high-speed milling processes, a novel method for dynamic optimization of system stability is used to determine the cutting parameters and structural parameters by increasing the chatter free material removal rate （CF-MRR） and surface finish. The method is hased on the theory of the chatter stability and the semi-bandwidth of the resonant region. The objective function of the method is material removal rate（MRR）,the constraints are chatter stability and surface finish, and the optimizing variables are cutting and structural parameters. The optimization procedure is stated. The method is applied to a milling system and CF-MRR is increased 18.86%. It is shown that the influences of the chatter stability and the resonance are simultaneously considered in the dynamic optimization of the milling system for increasing CF-MRR and the surface finish.

Investigation of Surface Roughness in High-Speed Milling of Aeronautical Aluminum Alloy

An approach is presented to optimize the surface roughness in high-speed finish milling of 7050- T7451 aeronautical aluminum alloy. In view of this, the multi-linear regression model for surface roughness has been developed in terms of slenderness ratio, cutting speed, radial depth-of-cut and feed per tooth by means of orthogonal experimental design. Variance analyses were applied to check the adequacy of the predictive model and the significances of the independent input parameters. Response contours of surface roughness were generated by using response surface methodology （RSM）. From these contours, it was possible to select an optimum combination of cutting parameters that improves machining efficiency without increasing the surface roughness.

INFLUENCE OF TOOL HELIX ANGLE ON STABILITY IN HIGH-SPEED MILLING PROCESS

An integrated dynamic model considering the influence of the helix angle is developed through dividing the cutting process into three cutting processes： uninterrupted, entry, and exit cutting processes. The semi-discretized technique is used to approximate the finite dimensional Floquet transition matrix of the dynamic control equation to determine the stability of milling process. The stability charts for helix mills are obtained. Results show that the helix angle plays an important role in the stability of milling process. The stability regions with helix angle become larger than those without helix angle. Some ＂islands＂ are presented in the stability charts, and ＂island＂ locations are determined by the relation between the axial depth of cut and the helix pitch. The ＂islands＂ are connected by the ＂bridge＂ by the effects of entry and exit cutting processes. The theoretical results are validated by milling experiments.

Modelling and simulation of high-speed milling chatter regeneration based on MATLAB

Considering the deficiency in milling process parameters selection, based on the modelling of dynamic milling force and the deduction of chatter stability limits, the chatter stability lobes simulation program for milling is developed with MAT- LAB. The simulation optimization application software of dynamics was designed using engineering simulation software Visio Basic. The chatter stability lobes for milling, which can be used as an instruction guide for the selection of process parameters, are simulated with frequency response functions （FRFs） gained by hammer test. The validation and accuracy of the simulation algorithm are verified by experiments. The simulation method has been used in a factory with an excellent application effect.

Surface Integrity of Inconel 738LC Parts Manufactured by Selective Laser Melting Followed by High-speed Milling

This study is concerned with the surface integrity of Inconel 738LC parts manufactured by selective laser melting(SLM)followed by high-speed milling(HSM).In the investigation process of surface integrity,the study employs ultradepth three-dimensional microscopy,laser scanning confocal microscopy,scanning electron microscopy,electron backscatter diffractometry,and energy dispersive spectroscopy to characterize the evolution of material microstructure,work hardening,residual stress coupling,and anisotropic effect of the building direction on surface integrity of the samples.The results show that SLM/HSM hybrid manufacturing can be an effective method to obtain better surface quality with a thinner machining metamorphic layer.High-speed machining is adopted to reduce cutting force and suppress machining heat,which is an effective way to produce better surface mechanical properties during the SLM/HSM hybrid manufacturing process.In general,high-speed milling of the SLM-built Inconel 738LC samples offers better surface integrity,compared to simplex additive manufacturing or casting.

Radial Grip Rigidity of the Matching of Lengthened Shrink-fit Holder and Cutter in High-speed Milling

Though the lengthened shrink-fit holder (LSFH) is widely applied in high speed milling of the parts characterized by deep cavities at present, its design and selection mainly depends on the experience and lacks a correct theoretical guidance. In this paper, attention is focus on the radial grip rigidity of the matching of LSFH and cutter in high speed milling. Based on the experiment modal analysis (EMA) technique, an accurate finite element model of the matching of LSFH and cutter is established firstly. Subsequently, the influence of different interference, grip length and spindle speed on the grip rigidity of LSFH are analyzed. The analysis results show that there is a reasonable interference and grip length between the LSFH and cutter so that to have a steepless grip and have a good radial grip rigidity and at the same time to avoid the strength of LSFH to exceed it’s yield limit which will reduce the precision and service life of LSFH, besides when spindle speed reach a extension the weakening influence of the centrifugal force on the radial grip rigidity of the matching of LSFH and cutter should been taken into account. Finally, the finite element analysis results are verified based on the construction of measurement method of the grip rigidity and the results fit very well. The studies provide a theoretical basis for the design, selection and the serialization and standardization of the matching of LSFH and cutter.

State Dependent Regenerative Delay Model for High-Speed Milling Processes

A 2 DOF dynamic model of regenerative chatter model with state-dependent time delay is developed in milling processes. Regenerative effects, ＂ploughing＂ or ＂rubbing＂ effects between the flank of the cutting edge and the machined surface, and feed effects are considered. It is shown that the regenerative delay is determined by the combination of the cutter rotation and the tool vibrations resulting in a state-dependent time delay. The governing equation is a delay-differential equation with state-dependent delay （SD-DDE）, as op- posed to the standard models with constant time delay. Based on Frechet derivative theory, the linearization of periodic state-dependent delay differential equation is also investigated. For a system with practical milling parameters, the incorporation of the state-dependent delay into the model does not essentially affect the linear stability properties of the system.

CUTTING TEMPERATURE MEASUREMENT IN HIGH-SPEED END MILLING

A computer aided measurement system is used to measure the cutting temperature directly in high-speed machining by natural thermocouples and standard thermocouples. In this system the tool/workpiece interface temperature is measured by the tool/workpiece natural thermocouple, while the temperature distribution on the workpiece surface and that of interior are measured by some standard thermocouples prearranged at proper positions. The system can be used to measure cutting temperature in the machining with the rotary cutting tools, such as vertical drill and end milling cutter. It is practically used for the research on high-speed milling with hardened steel.

Tool Life and Surface Integrity in High-speed Milling of Titanium Alloy TA15 with PCD/PCBN Tools

Titanium alloys are widely used in aeronautics that demand a good combination of high strength, good corrosion resistance and low mass. The mechanical properties lead to challenges in machining operations such as high process temperature as well as rapidly increasing tool wear. The conventional tool materials are not able to maintain their hardness and other mechanical prop- erties at higher cutting temperatures encountered in high speed machining. In this work, the new material tools, which are poly- crystalline diamond （PCD） and polycrystalline cubic boron nitride （PCBN） tools, are used in high-speed milling of Ti-6.5AI-2Zr-IMo-IV （TA15） alloy. The performance and wear mechanism of the tools are investigated. Compared to PCBN tool, PCD tool has a much longer tool life, especially at higher cutting speeds. Analyses based on the SEM and EDX suggest that attrition, adhesion and diffusion are the main wear mechanisms of PCD and PCBN tools in high-speed milling of TA 15. Oxida- tion wear is also observed at PCBN tool/workpiece interface. Roughness, defects, micro-hardness and microstructure of the ma- chined surface are investigated. The recorded surface roughness values with PCD/PCBN tools are bellow 0.3 μm at initial and steady cutting stage. Micro-hardness analysis shows that the machined surface hardening depth with PCD and PCBN tools is small. There is no evidence of sub-surface defects with PCD and PCBN tools. It is concluded that for TA15 alloy, high-speed milling can be carried out with PCD/PCBN tools.

Chip morphology and cutting temperature of ADC12 aluminum alloy during high-speed milling

The ADC12 aluminum alloy is prone to severe tool wear and high cutting heat during high-speed milling because of its high hardness.This study analyzes the highspeed milling process from the perspective of different chip morphologies.The influence of cutting temperature on chip morphology was expounded.A two-dimensional orthogonal cutting model was established for finite element analysis(FEA)of high-speed milling of ADC12 aluminum alloy.A theoretical analysis model of cutting force and cutting temperature was proposed based on metal cutting theory.The variations in chip shape,cutting force,and cutting temperature with cutting speed increasing were analyzed via FEA.The results show that,with the increase in cutting speed,the chip morphology changes from continuous to serrated,and then back to continuous.The serrated chip is weakened and the cutting temperature is lowered when the speed is lower than 600 m·min^(-1)or higher than 1800 m·min^(-1).This study provides a reference for reducing cutting temperature,controlling chip morphology and improving cutting tool life.

Expert Experience and Data-Driven Based Hybrid Fault Diagnosis for High-SpeedWire Rod Finishing Mills

The reliable operation of high-speed wire rod finishing mills is crucial in the steel production enterprise.As complex system-level equipment,it is difficult for high-speed wire rod finishing mills to realize fault location and real-time monitoring.To solve the above problems,an expert experience and data-driven-based hybrid fault diagnosis method for high-speed wire rod finishing mills is proposed in this paper.First,based on its mechanical structure,time and frequency domain analysis are improved in fault feature extraction.The approach of combining virtual value,peak value with kurtosis value index,is adopted in time domain analysis.Speed adjustment and side frequency analysis are proposed in frequency domain analysis to obtain accurate component characteristic frequency and its corresponding sideband.Then,according to time and frequency domain characteristics,fault location based on expert experience is proposed to get an accurate fault result.Finally,the proposed method is implemented in the equipment intelligent diagnosis system.By taking an equipment fault on site,for example,the effectiveness of the proposed method is illustrated in the system.

Microstructure and cutting performance of CrTiAlN coating for high-speed dry milling

Using a closed field unbalanced magnetron sputtering system,the cemented carbide end mills were coated with a CrTiAlN hard coating,which consisted of a Cr adhesive layer,a CrN interlayer and a CrTiAlN top layer.The microstructure and mechanical properties of the coating were investigated by X-ray diffraction（XRD）,scanning electron microscopy（SEM）,transmission electron microscopy（TEM）,micro indentation and scratch test.The cutting performance of the coated end mills were conducted by high-speed dry milling hardened steel（P20,HRC 45）.The results indicates that the coating is composed of（Cr,Ti,Al）N columnar grains with nanolayers.The coating exhibits good adhesion to cemented carbide substrate and high microhardness of around 30 GPa.The coated end mills show significant improvement on tool life and much lower cutting force as compared to the uncoated ones.And the related mechanisms were discussed.

Theoretical modeling of cutting temperature in high-speed end milling process for die/mold machining

A parametric model of cutting temperature generated in end milling process is developed according to the thermal mechanism of end milling as an intermittent operation, which periodically repeats the cycle of heating under cutting and cooling under non-cutting. It shows that cutting speed and the tool-workpiece engagement condition are determinative for tool temperature in the operation. The suggested model was investigated by tests of AlTiN coated endmill machining hardened die steel JIS SKD61, where cutting temperature on the flank face of tool was measured with an optical fiber type radiation thermometer. Experimental results show that the tendency of cutting temperature to increase with cutting speed and engagement angle is intensified with the progressing tool wear.

Application of On-Line Rail Milling in Rail Maintenance of High-Speed Railways

On-line rail milling technologies have been applied in rail maintenance, and are proving to be efficient and environmental friendly. Based on the field data of on-line rail milling, a program for comparing rail transverse profiles before and after milling was designed and the root mean square （RMS） amplitude of longitudinal profile was calculated. The application of on-line rail milling technology in removing rail surface defects, re-profiling railhead transverse profiles, smoothing longitudinal profiles and improving welding joint irregularity were analyzed. The results showed that the on-line rail milling technology can remove the surface defects at the rail crown and gauge comer perfectly, re-profile railhead transverse profile with a tolerance of - 1. 0-0.2 ram, improve longitudinal irregularity of rail surface, with the RMS amplitude of irregularity reduced more than 50% and the number of out-of- limited amplitude reduced by 42% - 82% in all wavelength ranges. The improvement of welding joint irregularity depends on the amount of metal removal determined by the milling equipment and the primal amplitude.

Surface Topography and Roughness of High-speed Milled AlMn1Cu

The aluminum alloy AlMn1Cu has been broadly applied for functional parts production because of its good properties. But few researches about the machining mechanism and the surface roughness were reported. The high-speed milling experiments are carried out in order to improve the machining quality and reveal the machining mechanism. The typical topography features of machined surface are observed by scan electron microscope（SEM）. The results show that the milled surface topography is mainly characterized by the plastic shearing deformation surface and material piling zone. The material flows plastically along the end cutting edge of the flat-end milling tool and meanwhile is extruded by the end cutting edge, resulting in that materials partly adhere to the machined surface and form the material piling zone. As the depth of cut and the feed per tooth increase, the plastic flow of materials is strengthened and the machined surface becomes rougher. However, as the cutting speed increases, the plastic flow of materials is weakened and the milled surface becomes smoother. The cutting parameters （e.g. cutting speed, feed per tooth and depth of cut） influencing the surface roughness are analyzed. It can be concluded that the roughness of the machined surface formed by the end cutting edge is less than that by the cylindrical cutting edge when a cylindrical flat-end mill tool is used for milling. The proposed research provides the typical topography features of machined surface of the anti-rust aluminum alloy AlMn1Cu in high speed milling.