The Research for Surface Properties of Steel Slag Powder and High-Temperature Rheological Properties of Asphalt Mortar

In order to evaluate the feasibility of steel slag powder as filler,the coating properties of steel slag and limestone aggregate were compared by water boiling test,the micro morphology difierences between steel slag powder and mineral powder(limestone powder)were compared by scanning electron microscope(SEM),and the high-temperature rheological properties of asphalt mortar with difierent ratio of filler quality to asphalt quality(F/A)and difierent substitution rates of mineral powder(S/F)were studied by dynamic shear rheological test.The results show that the surface microstructure of steel slag powder is more abundant than that of mineral powder,and the adhesion of steel slag to asphalt is better than that of limestone.At the same temperature,the lower the ratio of S/F is,the greater the rutting factor and complex modulus will be.In addition,the complex modulus and rutting factor of the asphalt mortar increase with the increase of F/A,and the filler type and F/A have a negligible efiect on the phase angle.

Synergistic effect of Zr and Mo on precipitation and high-temperature properties of Al-Si-Cu-Mg alloys

This study focuses on finding a solution to the sharp decline in mechanical properties of Al-Si-Cu-Mg alloys due to rapid coarsening of traditional intermediate phases at high temperature.A new type of modified al oy,to be used in automobile engines at high temperatures,was prepared by adding Zr and Mo into Al-Si-Cu-Mg alloy.The synergistic effects of Zr and Mo on the microstructure evolution and high-temperature mechanical properties were studied.Results show that the addition of Zr and Mo generates a series of intermetallic phases dispersed in the alloy.They can improve the strength of the alloy by hindering dislocation movement and crack propagation.In addition,some nano-strengthened phases show coherent interfaces with the matrix and improve grain refinement.The addition of Mo greatly improves the heat resistance of the alloy.The extremely low diffusivity of Mo enables it to improve the thermal stability of the intermetallic phases,inhibit precipitation during aging,reduce the size of the precipitates,and improve the heat resistance of the alloy.

High Temperature Rheological Performance of Graphene Modified Rubber Asphalt

To elucidate the high temperature rheological capability of graphene modified rubber asphalt,three contents of graphene and crumb rubber were prepared by a combination of mechanical agitation and high speed shearing machine,then used dynamic shear rheological test(DSR)and multiple stress creep recovery(MSCR)tests to evaluate.The hardness and softening point with rotational viscosity of samples raised with the addition of graphene,especially the addition of 0.04%.Dynamic shear rheological test revealedthat the dynamic shear modulus G*,rutting factor G*/Sin δ,and zero shear viscosity(ZSV)of graphene-modified rubber asphalt were greatly influenced along with graphene-increased,on the contrary,phase angle δ which characterize the viscoelastic ratio of asphalt decreased.Multiple stress creep recovery(MSCR)tests showed that the graphene-enhanced rubber asphalt had high-temperature stability through non-recoverable creep compliance(Jnr).Based on these findings,graphene-modified rubber asphalt binders with the addition of 0.04% graphene had good viscoelastic properties as well as high temperature rutting resistance performance.In the meantime,G*/Sin δ,ZSV,and Jnr100,Jnr3200 have good correlation,which can reveal the excellent high-temperature stability performance of asphalt.

Effect of Synthetic Conditions and Thickener Formulation on the Rheological and Tribological Properties of Polypropylene Grease

Polypropylene(PP)grease holds great potential for special industrial applications.In this study,synthetic conditions,thickener content,and the ratio of two different molecular weight PPs were investigated systematically using a rheometer,scanning electron microscope,X-ray diffraction,Fourier transform infrared spectrometer,oscillating tribometer,and 3D surface profiler measurements.The results showed that suitable synthetic conditions are two quenching cycles,and the synthetic temperature and time is 240℃for 12 h.The rheological analysis showed that thickener content and different proportions of the two PP molecular weights have a significant influence on the rheological properties of PP grease.High molecular weight PP(H-PP)has a stronger thickening ability than low molecular weight PP(L-PP).The higher the amount of H-PP in the fixed thickener content or the higher the thickener content with a specific proportion,the higher the viscoelasticity of PP grease.The tribological performance is related to the rheological properties.The proportion of two different molecular weight PPs in the thickener content should be appropriate;excessive H-PP content leads to lubrication failure.

Rheological and physicomechanical properties of rod milling sand-based cemented paste backfill modified by sulfonated naphthalene formaldehyde condensate

Rod milling sand(RMS)—a coarse sand aggregate—was recycled for cemented paste backfill(CPB)for the underground mined area at the Jinchuan nickel deposit,named rod milling sand-based cemented paste backfill(RCPB).The adverse effects of coarse particles on the transportation of CPB slurry through pipelines to underground stopes resulting in weakening of the stability of the backfill system are well known.Therefore,sulfonated naphthalene formaldehyde(SNF)condensate was used for the performance improvement of RCPB.The synergistic effect of solid content(SC),lime-to-sand ratio,and SNF dosage on the rheological and physicomechanical properties,including slump,yield stress,bleeding rate,uniaxial compressive strength(UCS),as well as mechanism analysis of RCPB,have been explored.The results indicate that the effect of SNF on RCPB performance is related to the SNF dosage,lime-to-sand ratio,and SC.The slump of fresh RCPB with 0.1wt%-0.5wt%SNF increased by 2.6%-26.2%,whereas the yield stress reduced by 4.1%-50.3%,indicating better workability and improved cohesiveness of the mix.The bleeding rate of fresh RCPB decreased first and then rose with the increase of SNF dosage,and the peak decrease was 67.67%.UCS of RCPB first increased and then decreased with the increase of SNF dosage.At the optimal SNF addition ratio of 0.3wt%,the UCS of RCPB curing for 7,14 and,28 d ages increased by 31.5%,28.4%,and 29.5%,respectively.The beneficial effects of SNF in enhancing the early UCS of RCPB have been corroborated.However,the later UCS increases at a slower rate.The research findings may guide the design and preparation of RCPB with adequate performance for practical applications.

Rheological Properties and Incipient Motion of Cohesive Sediment in the Haine Estuary of China

The Haihe cohesive sediment, which is typical in China, is studied systematically for its basic physical and incipient motion properties. Following the requirements of dredging works in the Haihe Estuary, cohesive sediment samples were taken from three locations. Laboratory experiments were conducted to determine the rheological properties of these samples and to examine the incipient motion of the cohesive sediment. It is found that the cohesive sediment has an obvious yield stress tau(b), which increases with the mud density in a manner of an exponential function, and so does the viscosity parameter eta. The cohesive sediment behaves like a Bingham fluid when its density is below 1.38 similar to 1.40 g/cm(3), and when denser than these values, it may become a power-law fluid. The incipient motion experiment also revealed that the incipient velocity of the cohesive sediment increases with die density in an exponential manner. Therefore, the incipient motion is primarily related to the density, which is different from the case for non-cohesive sediment in which the incipient motion is con-elated with the diameter of sand particles instead. The incipient motion occurs in two different ways depending on the concentration of mud in the bottom. For sufficiently fine particles and a concentration lower than 1.20 g/cm(3), the cohesive sediment appears as fluidized mud, and the incipient motion is in the form of instability of an internal wave. For a higher concentration, the cohesive sediment appears as general quasi-solid-mud, and the incipient motion can be described by a series of extended Shields curves each with a different porosity for newly deposited alluvial mud.

Structural Analysis and Magnetic Properties of Gd-Doped Li-Ni Ferrites Prepared Using Rheological Phase Reaction Method

A series of Gd-doped Li-Ni ferrites with the formula of LiNi0.5GdxFe2-xO4 where x = 0.00 - 0.08 in steps of 0.02, were prepared by thermolysis of oxalate precursors obtained by rheological phase reaction. The structure, morphology, and the magnetic properties of the samples were characterized by powder X-ray diffraction （XRD）, atomic force microscopy （AFM） and a vibrating sample magnetometer （VSM）. A single spinel phase was obtained in the range of x = 0.00 - 0.04. The lattice parameters of the Gd-doped samples were larger than that of pure Li-Ni ferrite, and increased in the range of 0.00 ≤ x ≤ 0.04, then decreased up to x = 0.08, because of the formation of the secondary phase （Gd- FeO3）. All samples were spheric particles with an average size of about 100 nm, but agglomerated to some extent. The hysteresis loops indicated that the saturation magnetization decreased gradually with increasing Gd content, while the variation of coercivity was related to the microstructure of the Gd-doped samples.

IMPROVEMENT OF RHEOLOGICAL AND SHAPE RETENTION PROPERTIES OF WAX-BASED MIM BINDER BY MULTI-POLYMER COMPONENTS

ＩＮＴＲＯＤＵＣＴＩＯＮＭｅｔａｌｉｎｊｅｃｔｉｏｎｍｏｌｄｉｎｇ（ＭＩＭ）ｉｓａｎｅｍｅｒｇｉｎｇｎｅｔｓｈａｐｉｎｇｐｒｏｃｅｓｗｉｔｈｔｈｅｃａｐａｂｉｌｉｔｙｏｆｐｒｏｄｕｃｉｎｇｃｏｍｐｌｅｘｍｅｔａｌｐｒｏｄｕｃｔｓｗｈｉｃｈｃａｎ?..

Traction rheological properties of simulative soil for deep-sea sediment

The traction capacity of the mining machine is greatly in?uenced by the traction rheological properties of the deep-sea sediments. The best simulative soil was prepared for substituting the deep-sea sediment based on the deep-sea sediment collected from the Paci?c C-C mining area. Traction rheological properties of the simulative soil were studied by a home-made test apparatus. In order to accurately describe the traction rheological properties and determine traction rheological parameters, the Newtonian dashpot in Maxwell body of Burgers model was replaced by a self-similarity spring-dashpot fractance and a new rheological constitutive model was deduced by fractional derivative theory. The results show the simulative soil has obvious non-attenuate rheological properties. The transient creep and stable creep rate increase with the traction, but they decrease with ground pressure. The fractional derivative Burgers model are better in describing non-attenuate rheological properties of the simulative soil than the classical Burgers model. For the new traction rheological constitutive equation of the simulative soil, the traction rheological parameters can be obtained by ?tting the tested traction creep data with the traction creep constitutive equation. The ground contact length of track and walking velocity of the mining machine predicted by the traction rheological constitutive equation can be used to take full advantages of the maximum traction provided by the soil and safely improve mining effciency.

INVESTIGATION OF STRUCTURE AND PROPERTIES FOR POLYMER SYSTEMS BASED ON DYNAMIC RHEOLOGICAL APPROACHES

The dynamic rheological measurements have been a preferred approach to the characterization of the structure and properties for multi-component or multi-phase polymer systems,due to its sensitive response to changes of structure for these heterogeneous polymers.In the present article,recent progresses in the studies on dynamic rheology for heterogeneous polymer systems including polymeric composites filled with inorganic particles,thermo-oxidized polyolefins,phase- separated polymeric blends and functional polymers with the scaling and percolation behavior are reviewed,mainly depending on the results by the authors' group.By means of rheological measurements,not only some new fingerprints responsible for the evolution of morphology and structure concerning these polymer systems are obtained,the corresponding results are also significant for the design and preparation of novel polymer-based composites and functional materials.

Rheological properties and viscosity reduction of South China Sea crude oil

The rheological properties of South China Sea （SCS） crude oil were studied. A group of synthetic long-chain polymers, including octadecyl acrylate-maleic anhydride bidodecyl amide copolymer （VR-D）, octadecyl acrylate-maleic anhydride bioctadecyl amide copolymer （VR-O） and octadecyl acrylate-maleic anhydride phenly amide copolymer （VR-A）, were employed to serve as viscosity reducers （VRs）. Their performance was evaluated by both experimental and computational methodologies. The results suggest that the SCS crude oil has low wax content yet high resin and asphaltene contents, which lead to high viscosity through formation of association structures. Additionally, the SCS crude oil appears to be a pseudoplastic fluid showing linear shear stress-shear rate dependence at low temperature. Interestingly, it gradually evolves into a Newtonian fluid with exponential relationship between shear stress and shear rate at higher temperature. Synthetic VRs demonstrate desirable and effective performance on improvement of the rheological properties of SCS crude oil. Upon the introduction of 1000ppm VR-O, which is synthesized by using octadecylamine in the aminolysis reaction, the viscosity of SCS crude oil is decreased by 44.2% at 15 ℃ and 40.2% at 40℃. The computational study suggests significant energy level increase and shear stress decrease for VR-containing crude oil systems.

Rheological properties of oil-based drilling fluids at high temperature and high pressure

The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental results show that the apparent viscosity,plastic viscosity and yield point decrease with the increase of temperature,and increase with the increase of pressure.The effect of pressure on the apparent viscosity,plastic viscosity and yield point is considerable at ambient temperature.However,this effect gradually reduces with the increase of temperature.The major factor influencing the rheological properties of oil-based drilling fluids is temperature instead of pressure in the deep sections of oil wells.On the basis of numerous experiments,the model for predict the apparent viscosity,plastic viscosity and yield point of oil-based drilling fluids at high temperature and pressure was established using the method of regressive analysis.It is confirmed that the calculated data are in good agreement with the measured data,and the correlation coefficients are more than 0.98.The model is convenient for use and suitable for the application in drilling operations.

Magnetic properties of La-Zn substituted Sr-hexaferrites by self-propagation high-temperature synthesis

The La-Zn substituted SrM-type ferrites with the composition of Sr1-xLaxFe12-xZnxO19 （x=0-0.4） were prepared by self-propagating high-temperature synthesis （SHS）. The single SrM phase was detected by XRD in the as-received samples by controlling the Fe contents in the reagents. The substitution of La^3＋and Zn^2＋ obviously increased the magnetic properties of the as-prepared samples. The maximum improvements of Br, Hcb and （BH）m were 14.4%, 15.3% and 30.7%, respectively compared with that of the samples without La-Zn substitution. Microstructure observation by SEM showed that the SHS method benefited forming the better particle features and achieving the higher Hcj in comparison with the traditional firing method.

Preparation of Polycarboxylate-based Superplasticizer and Its Effects on Zeta Potential and Rheological Property of Cement Paste

A series of polycarboxylate-based superplasticizers(PCs) with different structures were synthesized and the effects of chemical structure on zeta potential and rheological property of cement paste were studied. Residual monomers in each sample of PCs were quantitatively determined. The property of the polymers in cement was tested by micro-electrophoresis apparatus and R/S rheometer. Results showed that the zeta potential and its rheological properties are related with the side-chain length and density of PCs. The PCs having shorter side chain and lower side chain density exhibit higher anionic charge density, thus resulting in higher zeta potential. The effect of side chain density on zeta potential is more notable compared with that of side-chain length, and thus affecting the initial shear yield stress and apparent viscosity of the cement paste. In addition, although increasing the side chain length will result in reduction of the anionic charge density, the steric hindrance effect is obvious, which can effectively improve the dispersion of the cement particles, and reduce the viscosity and shear yield stress of slurry.

High-temperature mechanical properties of aluminium alloys reinforced with titanium diboride (TiB_2) particles

The physical and mechanical properties of metal matrix composites were improved by the addition of reinforcements. The mechanical properties of particulate-reinforced metal-matrix composites based on aluminium alloys （6061 and 7015） at high temperatures were studied. Titanium diboride （TiB2） particles were used as the reinforcement. All the composites were produced by hot extrusion. The tensile properties and fracture characteristics of these materials were investigated at room temperature and at high temperatures to determine their ultimate strength and strain to failure. The fracture surface was analysed by scanning electron microscopy. TiB2 particles provide high stability of the alumin- ium alloys （6061 and 7015） in the fabrication process. An improvement in the mechanical behaviour was achieved by adding TiB2 particles as reinforcement in both the aluminium alloys. Adding TiB2 particles reduces the ductility of the aluminium alloys but does not change the microscopic mode of failure, and the fracture surface exhibits a ductile appearance with dimples formed by coalescence.

Influence of Carboxyl Groups on the Particle Size and Rheological Properties of Polyacrylate Latices

The PAL was synthesized with BA,MMA and some monomers containing carboxyl groups（for example,acrylic acid（AA） and methacrylic acid（MAA）） as co-monomers by semi-continuous seeded emulsion polymerization technique.The influences of alkalinization temperature,the feeding manner of AA or MAA on the particles size,rheological properties and carboxyl distribution of the latex were discussed,and the rheological mechanism was analyzed.The experimental results show that the PAL system has preferable viscosity and particle size when the alkalinization temperature is 50 ℃.Different distribution of carboxyl group in the particles and different resultant rheological properties are obtained by different feeding manner of AA or MAA into the system.The TEM images show that the particle is a smooth globe with carboxyl group concentrating on the surface and stabilized with electric double layer and nonionic adsorbed layer.The concentration of carboxyl functional group on the surface of particles can be achieved by the specific polymerization technique.The rheologyical properties are determined by accretion of particle volume and variation of the two phase volume ratio resulted from the carboxyl group spreading layer.

Experimental evaluation on high temperature rheological properties of various fiber modified asphalt binders

High temperature rheological properties of fiber modified asphalt binders and impact of the type and content on such properties were studied.Three types of fiber,including polyester(PET),polyacrylonitrile(PAN) and cellulose(CEL),a control content(0%) and four levels of fiber content(2%,4%,6% and 8% by total asphalt binder mass) were used with asphalt binders.The high temperature rheological properties,consisting of complex modulus(G*) and phase angle δ,were measured using SHRP's dynamic shear rheometer(DSR) between 46-82 ℃.Experimental results indicate that the changes of G* and tan δ of fiber modified asphalt binders with the increase of test temperature tend to slow down,and the temperature susceptibility is improved obviously compared to that of original asphalt binder.Fiber modification results in the increase of rutting parameter(G*/sin δ) at high temperatures,the decrease of temperature susceptibility,and further improved high temperature performance of asphalt binder.An excellent correlation exhibits between fiber content and high temperature performance of asphalt binder.Moreover,fiber type also has different influences on the improvement of G*/sin δ,G*/sin δ of PET and PAN fiber asphalt binders are both higher than that of CEL fiber,but G*/sin δ of CEL fiber is still higher than that of original asphalt.However,there is a critical fiber content when fibers start to interact with each other.Therefore,based on the critical fiber content and economic consideration,the optimum fiber contents for various fiber-modified asphalt binders are obtained.

Variation and trends in dough rheological properties and flour quality in 330 Chinese wheat varieties

The objective of this study was to investigate variation and trends in dough rheological properties and flour quality traits in 330 Chinese wheat varieties. The dough rheological properties of development time(DT), stability time(ST), and farinograph quality number(FQN)were evaluated, as well as the flour quality traits of protein(PC), wet gluten content(WGC), and sedimentation value(SV). The coefficients of variation of DT(40.5%), ST(58.1%), and FQN(42.4%) were higher than those of PC(9.1%), WGC(10.1%), and SV(15.3%). Normal distributions were observed for the flour quality indices but not for the rheological parameters. SV was strongly correlated with the three rheological parameters and accordingly might be used as a primary indicator for dough rheological property evaluation. Our results showed that there has been marked improvement in dough rheological properties for Chinese wheat varieties released since 1986, while flour quality has remained stable.

Rheological properties of polymer micro-gel dispersions

The influence of swelling time, temperature, NaCl concentration and polymer micro-gel concentration on rheological properties of polymer micro-gel dispersions was studied by using a HAAKE rheometer. The results showed that with increasing swelling time and NaCl concentration, the polymer micro-gel dispersions changed from a shear-thickening fluid to a Newtonian fluid. The polymer micro-gel dispersion show shear-thinning in non-saline water. At higher swelling temperature, the time of the polymer micro-gel dispersion showing shear-thickening was shorter. With increasing polymer micro-gel concentration, the dispersion changed from shear-thickening to shear-thinning.

Study on the effect of wheat bran dietary fiber on the rheological properties of dough

The aim of the study was to determine the influence of wheat bran dietary fiber on wheat flour dough rheological properties.In this paper,wheat bran dietary fiber(WBDF)with different levels(0,3%,6%,9%,12%)were added to wheat flour and the characterization of dough rheological properties was conducted by rapid visco-analyzer,farinograph,as well as rotational rheometer.The results from pasting properties showed a gradual reduction in peak viscosity,trough viscosity,final viscosity and setback with increasing WBDF content.At high WBDF concentration,the significant increase of water absorption,formation time as well as weakening degree implied the harder formation of gluten network structure and the competition for water between gluten and WBDF particles.Such conclusion was in line with the findings from dynamic rheology tests,in which the doughs containing WBDF were more sensitive to strain regardless of their rigid and stiff texture.This study revealed vulnerable dough structure induced by WBDF,as well as the strengthened elastic property,elaborating the harmful effects ofWBDF on the rheological properties of doughs.