A multi-hole vertical-cavity surface-emitting laser （VCSEL） operating in stable single mode with a low threshold current was produced by introducing multi-leaf scallop holes on the top distributed Bragg-refleetor of...A multi-hole vertical-cavity surface-emitting laser （VCSEL） operating in stable single mode with a low threshold current was produced by introducing multi-leaf scallop holes on the top distributed Bragg-refleetor of an oxidation- confined 850 nm VCSEL. The single-mode output power of 2.6 mW, threshold current of 0.6 mA, full width of half maximum lasing spectrum of less than 0.1 nm, side mode suppression ratio of 28.4 dB, and far-field divergence angle of about 10% are obtained. The effects of different hole depths on the optical characteristics are simulated and analysed, including far-field divergence, spectrum and lateral cavity mode. The single-mode performance of this multi-hole device is attributed to the large radiation loss from the inter hole spacing and the scattering loss at the bottom of the holes, particularly for higher order modes.展开更多
The influences of the mask wall angle on the current density distribution,shape of the evolving cavity and machining accuracy were investigated in electrochemical machining(ECM) by mask.A mathematical model was develo...The influences of the mask wall angle on the current density distribution,shape of the evolving cavity and machining accuracy were investigated in electrochemical machining(ECM) by mask.A mathematical model was developed to predict the shape evolution during the ECM by mask.The current density distribution is sensitive to mask wall angle.The evolution of cavity is determined by the current density distribution of evolving workpiece surface.The maximum depth is away from the center of holes machined,which leads to the island appearing at the center of cavity for mask wall angles greater than or equal to 90°(β≥90°).The experimental system was established and the simulation results were experimentally verified.The results indicate that the simulation results of cavity shape are consistent with the actual ones.The experiments also show that the repetition accuracy of matrix-hole for β≥90° is higher than that for β<90°.A hole taper is diminished,and the machining accuracy is improved with the mask wall angle increasing.展开更多
To overcome the shortcomings of conventional plasma arc welding （ PAW）, the ＇ controlled pulse key-holing＇ strategy is proposed and the keyhole PAW experiment system is developed. ＇The efflux plasma voltage signa...To overcome the shortcomings of conventional plasma arc welding （ PAW）, the ＇ controlled pulse key-holing＇ strategy is proposed and the keyhole PAW experiment system is developed. ＇The efflux plasma voltage signal is detected in realtime to characterize the keyhole size and dimension. The welding current waveform for controlled pulse key-holing strategy is implemented, and two slow-decreasing slopes are added at the dropping point from peak current to base current to further reduce both heat input and arc force so that the controllability of keyhole dynamics is improved. Two kinds of PAW tests are conducted, anti the different parameters of the controlled pulse current and the relevant efflux plasma voltage are measured in real-time to investigate ihe effects of welding current waveform parameters on the key-holing condition.展开更多
基金Project supported by the National High Technology Research and Development Program of China (Grant No. 2008AA03Z402)the National Natural Science Foundation of China (Grant No. 61076044)the Natural Science Foundation of Beijing,China(Grant Nos. 4092007 and 4102003)
文摘A multi-hole vertical-cavity surface-emitting laser （VCSEL） operating in stable single mode with a low threshold current was produced by introducing multi-leaf scallop holes on the top distributed Bragg-refleetor of an oxidation- confined 850 nm VCSEL. The single-mode output power of 2.6 mW, threshold current of 0.6 mA, full width of half maximum lasing spectrum of less than 0.1 nm, side mode suppression ratio of 28.4 dB, and far-field divergence angle of about 10% are obtained. The effects of different hole depths on the optical characteristics are simulated and analysed, including far-field divergence, spectrum and lateral cavity mode. The single-mode performance of this multi-hole device is attributed to the large radiation loss from the inter hole spacing and the scattering loss at the bottom of the holes, particularly for higher order modes.
基金Project(50635040) supported by the National Natural Science Foundation of ChinaProject(2009AA044205) supported by the National High Technology Research and Development ProgramProject(BK2008043) supported by the Jiangsu Provincial Natural Science Foundation,China
文摘The influences of the mask wall angle on the current density distribution,shape of the evolving cavity and machining accuracy were investigated in electrochemical machining(ECM) by mask.A mathematical model was developed to predict the shape evolution during the ECM by mask.The current density distribution is sensitive to mask wall angle.The evolution of cavity is determined by the current density distribution of evolving workpiece surface.The maximum depth is away from the center of holes machined,which leads to the island appearing at the center of cavity for mask wall angles greater than or equal to 90°(β≥90°).The experimental system was established and the simulation results were experimentally verified.The results indicate that the simulation results of cavity shape are consistent with the actual ones.The experiments also show that the repetition accuracy of matrix-hole for β≥90° is higher than that for β<90°.A hole taper is diminished,and the machining accuracy is improved with the mask wall angle increasing.
基金Acknowledgement The authors are grateful to the financial support for this research from the National Natural Science Foundation of China （Key Program Grant No. 50936003）.
文摘To overcome the shortcomings of conventional plasma arc welding （ PAW）, the ＇ controlled pulse key-holing＇ strategy is proposed and the keyhole PAW experiment system is developed. ＇The efflux plasma voltage signal is detected in realtime to characterize the keyhole size and dimension. The welding current waveform for controlled pulse key-holing strategy is implemented, and two slow-decreasing slopes are added at the dropping point from peak current to base current to further reduce both heat input and arc force so that the controllability of keyhole dynamics is improved. Two kinds of PAW tests are conducted, anti the different parameters of the controlled pulse current and the relevant efflux plasma voltage are measured in real-time to investigate ihe effects of welding current waveform parameters on the key-holing condition.
基金The project supported by the Natural Science Foundation of Shanghai Municipal Commission of Science and Technology under Grant Nos. 04ZR14059 and 04DZ05905, National Natural Science Foundation of China under Grant No. 10447125
