Preparation of Al-doped ZnO sputter target by hot pressing

Al-doped ZnO （AZO） target was prepared by hot pressing using ZnO and Al2O3 powder in mass ratio of 98：2.The effects of hot pressing conditions including temperature,pressure and preserving time on relative density were investigated.Pore evolution and phase structure change during densification process were studied.The results show that AZO target with super high relative density of 99% was prepared by two-stage hot pressing method under pressure of 35MPa,temperature of 1 050℃ and 1 150℃ with preserving time of 1 h,respectively.At temperature around 1 050℃,the number of isolated pore wasminimum.At temperature lower than 900℃,there existed Al2O3 phase.At temperature higher than 1 000℃,ZnAl2O4 phase was generated and its content was increased with temperature increasing.Hot pressing method had the advantage over pressureless sintering that the content of ZnAl2O4 was lower and sintering temperature could be also lower.With increasing the hot pressing temperature and preserving time,the electric resistivity of AZO target decreased greatly.A low resistivity of 3 10-3 cm was achieved under the temperature of 1 100℃,pressure of 35MPa and preserving time of 10 h.

Hot pressing densification of WC-Mo_xC binderless carbide

WC-6MoxC-0.47Cr3C2-0.28VC binderless carbide was prepared by hot pressing （1700 °C, 20 MPa）. The sample was observed and analyzed by scanning electron microscopy, energy dispersive X–ray spectroscopy and X–ray diffraction. The results show that during the hot pressing process, W atoms dissolve substantially into the MoxC crystal lattices; whilst, the reverse dissolution of Mo atoms into the WC crystal lattices takes place. Consequently, the main phase and binder phase structure are formed. The phase compositions of the main phase and binder phase are a WC-based solid solution containing Mo and a Mo2C-based solid solution containing W, respectively. The isotropic dissolution and precipitation of W and Mo atoms do not result in substantial carbide coarsening. The mechanism for the densification was discussed.

Effect of consolidation parameters on mechanical properties of Cu-based bulk amorphous alloy consolidated by hot pressing

Cu50Zr40Ti10 bulk amorphous alloys were fabricated by hot pressing gas-atomized Cu50Zr40Ti10 amorphous powder under different consolidation conditions without vacuum and inert gas protection. The consolidation conditions of the Cu50Zr40Ti10 amorphous powder were investigated based on an L9（34） orthogonal design. The compression strength and strain limit of the Cu50Zr40Ti10 bulk amorphous alloys can reach up to 1090.4 MPa and 11.9 %, respectively. The consolidation pressure significantly influences the strain limit and compression strength of the compact. But the mechanical properties are not significantly influenced by the consolidation temperature. In addition, the preforming pressure significantly influences not the compression strength but the strain limit. The optimum consolidation condition for the Cu50Zr40Ti10 amorphous powder is first precompacted under the pressure of 150 MPa, and then consolidated under the pressure of 450 MPa and the temperature of 380 °C.

Microstructures and mechanical properties of 2024Al/Gr/SiC hybrid composites fabricated by vacuum hot pressing

The 2024Al/Gr/SiC hybrid composite plates with 5%-10% SiC particles （volume fraction） and 3%-6% flaky graphite （Gr） （volume fraction） were fabricated by vacuum hot pressing and hot extrusion processing. The effects of SiC and Gr on the microstructures and mechanical properties of the composites aged at 160, 175 and 190℃ were studied by optical microscopy, scanning electron microscopy （SEM）, and hardness and tensile tests. The results indicate that the SiC particles have a more obvious effect on accelerating the aging response as compared with the Gr. Both the tensile strength and elongation are reduced by the Gr and SiC particles added into the matrix, while the Gr has a more negative influence on the elongation than the SiC particles. The tensile strength （ab）, yield stress （as） and elongation （δ） of the 2024Al/3Gr/10SiC composite aged at 165℃ for 8 h are 387 MPa, 280.3 MPa and 5.7%, respectively. The hybrid composites are characterized by ductile fracture, which is associated with the ductile fracture of the matrix and the tearing of the interface between the matrix and the particles.

Solid-state bonding between Al and Cu by vacuum hot pressing

Diffusion bonding between aluminum and copper was performed by vacuum hot pressing at temperatures between 623 and 923 K through two thermal processes： hot compression under the deformation rate of 0.2 mrrdmin for 10 rain at pre-set temperatures, and additional pressing at 0.2 mm/min for 20 rain during furnace cooling. After analyzing interface, the feasible diffusion bonding temperature was suggested as 823 K. The three major intermetallic layers generated during diffusion bonding process were identified as AIECu, AlCu＋AlaCu4 and Al4Cu9. Furthermore, local hardness values ofAlECU, AlCu＋AlaCu4 and Al4Cu9 layers average at （4.97±0.05）, （6.33±0.00） and （6.06±0.18） GPa, respectively.

Wear behavior of Ti6Al4V biomedical alloys processed by selective laser melting, hot pressing and conventional casting

The aim of this work was to study the influence of the processing route on the microstructural constituents,hardness andtribological(wear and friction)behavior of Ti6Al4V biomedical alloy.In this sense,three different processing routes were studied:conventional casting,hot pressing and selective laser melting.A comprehensive metallurgical,mechanical and tribologicalcharacterization was performed by X-ray diffraction analysis,Vickers hardness tests and reciprocating ball-on-plate wear tests ofTi6Al4V/Al2O3sliding pairs.The results showed a great influence of the processing route on the microstructural constituents andconsequent differences on hardness and wear performance.The highest hardness and wear resistance were obtained for Ti6Al4Valloy produced by selective laser melting,due to a markedly different cooling rate that leads to significantly different microstructurewhen compared to hot pressing and casting.This study assesses and confirms that selective laser melting is potential to producecustomized Ti6Al4V implants with improved wear performance.

Porous bulk metallic glass fabricated by powder hot pressing

A synthesis method for the production of porous bulk metallic glass (BMG) was introduced. This method utilizes the su- perplastic forming ability of amorphous powder in the supercooled liquid (SCL) state and intenerating salt mixture as a placeholder to produce BMG foam by using a hot die pressing method. Scanning electron microscope (SEM), X-ray diffraction (XRD) and dif- ferential scanning calorimetry (DSC) were employed to characterize the morphologies of foaming structure, the crystallization and the percentage of crystallization of the as-produced porous BMG. The results suggested that the formation of porous structure by su- perplastic forming process is feasible. Good bonding effect was observed between amorphous powder particles. Less than 6.5% of crystalline phases were formed during hot pressing, and less than 5.5% of residual salt was enclosed in the foam. To remove any re- sidual salt particles, salt preforms with three-dimensional network and good connectivity is necessary.

Mechanical and wear properties of Al-Al_3Mg_2 nanocomposites prepared by mechanical milling and hot pressing

β-A13Mg2 intermetallic was used as a reinforcing agent to improve the mechanical properties of an aluminum matrix. Different amounts of A13Mg2 nanoparticles （ranging from 0wt% to 20wt%） were milled with aluminum powders in a planetary ball mill for 10 h. Consolidation was conducted by uniaxial pressing at 400β under a pressure of 600 MPa for 2 h. Microstructural characterization confirms the uniform distribution of A13Mg2 nanoparticles within the matrix. The effects of nano-sized A13Mg2 content on the wear and mechanical properties of the composites were also investigated. The results show that as the A13Mg2 content increases to higher levels, the hardness, compressive strength, and wear resistance of the nanocomposites increase significantly, whereas the relative density and ductility decrease. Scanning electron microscopy （SEM） analysis of worn surfaces reveals that a transition in wear mechanisms occurs from delamination to abrasive wear by the addition of A13Mg2 nanoparticles to the matrix.

Diffusion behavior of Nb element in high Nb containing TiAl Alloys by reactive hot pressing

Diffusion behavior of Nb in elemental powder metallurgy high Nb containing TiAl alloys was investigated. The results show that Nb element dissolves into the matrix by diffusion. Pore nests are formed in situ after Nb diffusion. With the increase in hot pressing temperature, the diffusion of Nb will be more sufficient, and the microstructure is more homogeneous. Nb element diffuses completely at 1400℃. Meanwhile, compression deformation and agglomeration phenomena of pores are observed in some pore nests. Hot isostatic pressing （HIP） treatment can only efficiently decrease but not eliminate porosity completely.

Fabrication of Ni_3Al by hot pressing from element powders

Ni3Al intermetaUic was synthesized by hot pressing from element powders of nickel, aluminum, and boron. The influences of parameters on the properties of Ni3Al were investigated. The parameters include the particle size of nickel powder, adding or without boron powder, hot pressing temperature, etc. The properties include the density of hot-pressed samples, resultant redo of Ni3A1 phase, and bending strength. The microstructures of hot-pressed samples were investigated by X-ray diffraction and scan electronic microscopy, and the properties, such as density and bending strength, were also measured. The results show that a higher bending strength was obtained under the same hot pressing conditions by the fine nickel powder than the coarse one, and there is little difference about density. Boron powder added in this process accelerates the formation of Ni3Al and markedly increases the hot pressed density. In the temperature range of this study, the density increases along with the hot pressing temperature. Full dense Ni3Al samples were obtained under the condition of 860℃, 10 min, 45 MPa from Ni-22.89A1-0.5B powder.

Effects of hot pressing on electric performances of Bi_(0.5)Sb_(1.5)Te_(3)

The effects of hot pressing on electric performance and mechanical strength of Bi_(0.5)Sb_(1.5)Te_(3) thermoelectric material prepared through vacuum melting and milling were studied.The phase constituent and microstructure were analyzed by X-ray Diffraction and cold field emission Scanning Electric Microscope.Aeolotropisms of the material on microstructure and electric performances are approved.With the rise of hot pressing temperature(from 300-500℃)and pressure(30-70 MPa),electric conductivity and power factor are improved.Moreover,Bi_(0.5)Sb_(1.5)Te_(3) material can gain ideal thermoelectric performances and increased mechanical strength by hot pressing.

Comparative study of β-Si_3N_4 powders prepared by SHS sintered by spark plasma sintering and hot pressing

β-Si3N4 powders prepared by self-propagating high-temperature synthesis （SHS） with additions of Y2O3 and Al2O3 were sintered by spark plasma sintering （SPS）. The densification, microstructure, and mechanical properties of Si3N4 ceramics prepared using this method were compared with those obtained by hot pressing process. Well densified Si3N4 ceramics with finer and homogeneous microstructure and better mechanical properties were obtained in the case of the SPS technique at 200°C lower than that of hot pressing. The microhardness is 15.72 GPa, the bending strength is 716.46 MPa, and the fracture toughness is 7.03 MPa·m1/2.

Improving the Properties of Fast-Growing Chinese Fir by Vacuum Hot Pressing Treatment

Chinese fir was compressed by vacuum hot pressing and conventional hot pressing at different temperatures(180℃,200℃ and 220℃),respectively.The color parameters of the heat-compressed sample were measured,the relative mechanical properties of the material were tested and changes in the chemistry of fir were investigated using Fourier transform infrared spectroscopy(FTIR)and Xray photoelectron spectroscopy(XPS).The results indicated that the color difference between compressed and untreated wood increased gradually with the increase of temperature.Compared with the conventional hot pressing treatment,the color difference(ΔE*)of the Chinese fir treated by vacuum hot pressing decreased by 43.73%,69.91%,and 77.17%,respectively.The mechanical properties(bending elastic modulus and bending strength)of Chinese fir treated by vacuum hot pressing were significantly improved.The 24-hour water absorption thickness expansion rate of fir treated by vacuum hot pressing is smaller than that of conventional hot pressing.It is implied that vacuum hot pressing treatment is an effective method to produce compressed wood,which can improve the mechanical properties and dimensional stability of wood,and reduce the influence of carbonization on wood color.

Preparation of ZrB_2 Ceramics by Self-propagating High-temperature Synthesis and Hot Pressing Sintering

ZrB2 ceramics were prepared by self-propagating high-temperature synthesis（SHS） and were sintered by hot pressing（HP）.The effects of the granularities and doses of raw materials in Zr-B2O3-Mgon SHS process and product were investigated.XRD and combustion temperature curves prove that the ideal SHS reactants of Zr-B2O3-Mg are 50μm Zr powder,75μm B2O3 powder and 400μm Mg powder with 45% excessive.The particle sizes of SHS product,acid-leached product,sintered product are 2-5μm,0.5-2μm,2-10μm respectively.Chemical analysis indicates that the acid-leached product consists of ZrB2（94.59%）,ZrO2（3.87%）,and H3BO3（1.54%）,The sintered product has a relative density of 95.4%.

Fabrication of FeAl/TiC composites through reactive hot pressing

FeAl/TiC composites were fabricated by reactive hot pressing blended elemental powders. The TiC content was varied from 50% to 80%(volume fraction) and the aluminum content in the binder phase was changed from 40% to 50%(mole fraction). The effects of these compositional changes on the densification process and mechanical properties were studied. The results show that with the increase of TiC content, densities of the composites decrease due to insufficient particle rearrangement aided by (dissolutionreprecipitation) reaction during hot pressing. Closely related with their porosities and defect amount, the hardness and bend strength of the composites show peak values, attaining the highest values with TiC content being 70% and 60%, respectively. Increasing the aluminum content is beneficial to the densification process. But the hardness and bend strength of the composites are reduced to some extent due to the formation of excessive oxides and thermal vacancies.

Preparation of in situ and ex situ reinforced Fe–10Cr–1Cu–1Ni–1Mo–2C containing NbC particles by milling and hot pressing

An in situ and ex situ reinforced powder metallurgy （PM） steel was prepared by the combination of high-energy ball milling and subsequent hot pressing of elemental mixed powders of Fe-10Cr-1Cu-1Ni-1Mo-2C by mass with the addition of NbC particles. A 40-h milling pretreatment makes the powder particles nearly equiaxed with an average diameter of-8 μm, and the ferrite grain size is refined to -6 nm. The sintered density reaches 99.0%-99.7% of the theoretical value when the sintering is conducted at temperatures greater than 1000℃ for 30 min. In the sintered bulk specimens, the formation of an in situ M7C3 （M = Cr, Fe, Mo） phase is confirmed. MTC3 carbides with several hundred nanometers in size are uniformly distributed in the matrix. Some ultra-fine second phases of 50-200 nm form around the ex situ NbC and in situ M7C3 particles. The sintered steel exhibits an excellent combination of hardness （〉 Hv 500） and compressive strength （2100-2420 MPa）.

Mechanical properties and microstructure of in situ TiB_2/Cu composite fabricated by reactive hot pressing

A copper matrix composite reinforced by TiB_2 particle was fabricated by reactions of Cu,Ti and B powders.The microstructure and mechanical properties of the in situ composite were investigated.The results showed that the in situ formed TiB_2 particles,which has a size of no larger than 1 μm,exhibits a uniform distribution in the copper matrix.Due to TiB_2 reinforcement,the mechanical properties in terms of Young's modulus and yield and ultimate tensile stress of the in situ TiB_2/Cu composite are improved greatly.In addition,even if the volume fraction of TiB_2 reinforcement are the same,the composite in the present study containing fine TiB_2 particles exhibits much higher properties than that of the composite reinforced with coarse ones.

Preparation of TiAl/Ti_2AlC Composites with Ti/Al/C Powders by In-situ Hot Pressing

TiAl/Ti2AlC composites were prepared by in-situ hot pressing of TilAl/C powders mixtures and sintered at different temperatures were investigated by X- ray diffraction （ XRD ） of samples. The reaction procedure of Ti-Al-C system could be divided into three stnges. Below 900℃ , Ti reacts with Al to form TiAl intermetallics ; above 900 ℃ , C reacts with remain Ti to form TiC triggered by the exothermal reaction of Ti and Al ; TiAl reacts with TiC to produce dense TiAl/Ti2AlC compasites.In the holding stage, ternary Ti2AlC develops to layered polycrystal and composites pyknosis in the meanwhile. The mechanism of synthesis and microstructure was especially discussed.

Thermodynamic Analysis of Combusion Synthesis and Reaction Hot Pressing of Al_2O_3/B_4C Composite

The equilibrium phases and adiabatic temperature for combustion synthesis and reaction hot pressing of Al 2O 3/B 4C employing ① Al, B 2O 3 and C ② C, B, Al 2O 3 as starting reactants were analyzed by the CALPHAD technique. It is shown that the equilibrium phases at the adiabatic temperature in the combusion system (1) are not the intended composite Al 2O 3/B 4C but other phases. Good agreement with the experimental data was achieved for the calculated adiabatic temperature. The results were discussed with respect to the elimination of the by product in the combustion synthesis. It also revealed that the reactant mixture (2) is a weak exothermic or endothermic reaction system, which can be employed in the reaction hot pressing.