Microstructure evolution and strengthening mechanism of high -performance powder metallurgy TA15 titanium alloy by hot rolling

Hot deformation of sintered billets by powder metallurgy(PM)is an effective preparation technique for titanium alloys,which is more significant for high-alloying alloys.In this study,Ti–6.5Al–2Zr–Mo–V(TA15)titanium alloy plates were prepared by cold press-ing sintering combined with high-temperature hot rolling.The microstructure and mechanical properties under different process paramet-ers were investigated.Optical microscope,electron backscatter diffraction,and others were applied to characterize the microstructure evolution and mechanical properties strengthening mechanism.The results showed that the chemical compositions were uniformly dif-fused without segregation during sintering,and the closing of the matrix craters was accelerated by increasing the sintering temperature.The block was hot rolled at 1200℃ with an 80%reduction under only two passes without annealing.The strength and elongation of the plate at 20–25℃ after solution and aging were 1247 MPa and 14.0%,respectively,which were increased by 24.5%and 40.0%,respect-ively,compared with the as-sintered alloy at 1300℃.The microstructure was significantly refined by continuous dynamic recrystalliza-tion,which was completed by the rotation and dislocation absorption of the substructure surrounded by low-angle grain boundaries.After hot rolling combined with heat treatment,the strength and plasticity of PM-TA15 were significantly improved,which resulted from the dense,uniform,and fine recrystallization structure and the synergistic effect of multiple slip systems.

Design,preparation,microstructure and mechanical property of the lightweight radiation-shielding Mg-Ta-Al composites basing differential temperature hot rolling

A novel lightweight,radiation-shielding Mg-Ta-Al layered metal-matrix composite(LMC)was successful designed by doping the extremely refractory metal(Ta)into Mg sheets.These Mg-based LMCs sheets shows excellent radiation-dose shield effect,about 145 krad·a^(−1),which is about 17 times of traditional Mg alloy,while its surface density is only about 0.9 g·cm^(−2),reducing by 60%than that of pure Ta.The quantitate relationship between radiation-dose and the materials’thickness was also confirmed to the logistic function when the surface density is in the range of 0.6-1.5 g·cm^(−2).Meantime,the rolling parameters,interface microstructure and mechanical properties in both as-rolled and annealing treated samples were evaluated.The sheets possess a special dissimilar atoms diffusion transitional zone containing an obvious inter-diffusion Mg-Al interface and the unique micro-corrugated Ta-Al interface,as well as a thin Al film with a thickness of about 10μm.The special zone could reduce the stress concentration and enhance the strength of Mg-Ta-Al LMCs.The interface bonding strength reaches up to 54-76 MPa.The ultimate tensile strength(UTS)and yield strength(TYS)of the Mg-Ta-Al sheet were high to 413 MPa and 263 MPa,respectively,along with an elongation of 5.8%.The molecular dynamics(MD)analysis results show that the two interfaces exhibit different formation mechanism,the Mg-Al interface primarily depended on Mg/Al atoms diffusion basing point defects movement,while the Ta-Al interface with a micro-interlock pining shape formed by close-packed planes slipping during high temperature strain-induced deformation process.

Influence of Production Sequence of Aluminum Alloy Hot Rolling on Strip Surface Quality

With the intensification of market competition in the aluminum alloy strip processing industry,it is dif-ficult to control the mass production of the same specifications,which is bound to affect the hot rolling production.This paper studied the effect of the hot rolling order of aluminum alloy on the surface quality of strip,such as roll printing,color difference,anodic oxidation,etc.,reasonable discharge sequence and corresponding optimization measures were formulated.

Achieving oxidation protection effect for strips hot rolling via Al_(2)O_(3) nanofluid lubrication

It was discovered the application of Al_(2)O_(3) nanofluid as lubricant for steel hot rolling could synchronously achieve oxidation protection of strips surface.The underlying mechanism was investigated through hot rolling tests and molecular dynamics (MD) simulations.The employment of Al_(2)O_(3) nanoparticles contributed to significant enhancement in the lubrication performance of lubricant.The rolled strip exhibited the best surface topography that the roughness reached lowest with the sparsest surface defects.Besides,the oxide scale generated on steel surface was also thinner,and the ratio of Fe_(2)O_(3) among various iron oxides became lower.It was revealed the above oxidation protection effect of Al_(2)O_(3) nanofluid was attributed to the deposition of nanoparticles on metal surface during hot rolling.A protective layer in the thickness of about 193 nm was formed to prevent the direct contact between steel matrix and atmosphere,which was mainly composed of Al_(2)O_(3) and sintered organic molecules.MD simulations confirmed the diffusion of O_(2) and H_(2)O could be blocked by the Al_(2)O_(3) layer through physical absorption and penetration barrier effect.

Technological investigation on the Short Stroke Width Control Rolling in the Rougher Mills of Hot Strip Continuous Rolling Mill Train

According to technological requirement of hot charge rolling and hot direct rolling,in this paper,we investigated the technology of the width control rolling in the rougher mills of hot strip continuous rolling mill train.On the basis of improving width range of continuous casting of slab,we obtained a good result of greatly increasing the yield of slab→coil is achieved.

A homeodomain-leucine zipper I transcription factor, MeHDZ14,regulates internode elongation and leaf rolling in cassava(Manihot esculenta Crantz)

Drought stress impairs plant growth and other physiological functions. MeHDZ14, a homeodomainleucine zipper I transcription factor, is strongly induced by drought stress in various cassava cultivars.However, the role of MeHDZ14 in cassava growth regulation has remained unclear. Here we report that MeHDZ14 affected plant height, such that a dwarf phenotype and altered internode elongation were observed in transgenic cassava lines. MeHDZ14 was found to negatively regulate the biosynthesis of lignin. Its overexpression resulted in abaxially rolled leaves. The morphogenesis of leaf epidermal cells was inhibited by overexpression of MeHDZ14, with decreased auxin and gibberellin and increased cytokinin contents. MeHDZ14 was found to regulate many drought-responsive genes, including genes involved in cell wall synthesis and expansion. MeHDZ14 bound to the promoter of caffeic acid 3-Omethyltransferase 1(MeCOMT1), acting as a transcriptional repressor of genes involved in cell wall development. MeHDZ14 appears to act as a negative regulator of internode elongation and epidermal cell morphogenesis during cassava leaf development.

Edge crack damage analysis of AZ31 magnesium alloy hot-rolled plate improved by vertical roll pre-rolling

In the present study,through vertical roll pre-rolling of AZ31 magnesium alloy hot-rolled plate at room temperature,the effect of different vertical roll pre-rolling reduction on edge crack of the plate during flat rolling was systematically studied.The evolution of microstructure and texture in the edge and middle of the plate after vertical roll pre-rolling,heating and rolling was analyzed by using EBSD technology.The results show that during the vertical roll pre-rolling,{10–12}primary twins and{10–12}-{10–12}secondary twins dominated the edge deformation,while{10–12}primary twins dominated the middle deformation.With the increase of vertical roll pre-rolling reduction,the twin volume fraction of the edge and the middle increased,and the difference between them decreased gradually.After heating,the twin orientation caused by vertical roll pre-rolling was still maintained,and there was a significant difference in grain size between the edge and the middle.When the reduction rate of flat rolling was 30%,cracks have already appeared in the initial plate,while the vertical roll pre-rolled samples showed extremely high rolling performance.When the reduction rate of flat rolling was 50%,the 8PR sample still had no crack initiation.In addition,after flat rolling of 50%,the initial plate showed a strong basal texture,while the maximum pole density of the 8PR plate was small,and the texture distribution was very scattered,showing the characteristics of weak orientation.

Slab Tracking and Controlling on Hot Plate Rolling Line

By studying the slab moving in detail in the plate rolling process, the problem of slab tracking and controlling was solved by using the distributed control system. The problems of rhythm control for the big-complex system, the exchange of manual and automatic operations, the data exchange between the levelⅠ, TCS (technology control system) and levelⅡ, PCS (process control system), are solved. By this way, the automatic level of the plate production line is improved.

FEM modeling of dynamical recrystallization during multi-pass hot rolling of AM50 alloy and experimental verification

The microstructure simulation during the multi-pass hot rolling of AM50 alloy was studied by DEFORM-3D. The excellent agreement with the experiment observations shows that the present modeling and user routine are feasible for the reproduce of the hot rolling process. The multi-pass hot rolling contributes to the achievement of a uniformly recrystallized microstructure with fine grains in the rolled sheet. The sheet temperature before the finish rolling strongly affects the final grain size, but hardly affects the grain size distribution. This modeling and the user routine also have a potential to be applied in the researches of the other multi-pass hot deformation process.

Effects of magnetic field and hot rolling on microstructures and properties of cryo ECAPed 1050 aluminum alloy during annealing

The evolution of hardness and microstructures of 1050 aluminum alloy prepared by hot rolling and subsequent equal- channel angular pressing at cryogenic temperature (cryoECAP) after annealing at 150?400 °C for 1 h without and with magnetic field of 12 T was investigated. The electron back scattering diffraction pattern (EBSD) and transmission electron microscopy (TEM) were utilized to characterize the grain microstructures and dislocations. It is demonstrated that the hot rolling before cryoECAP produces more equiaxed grains with a smaller average size and a higher fraction of high angle boundaries (HABs) in the subsequent cryoECAPed 1050 aluminum alloy, thus accelerating the recovery and recrystallization of cryoECAPed alloy and produces more homogeneous microstructure during annealing. The magnetic field promotes the recovery and recrystallization and leads to much lower hardness at 150?250 °C, while it can suppress the abnormal grain growth and form more homogeneous grain size distributions annealed at 300?400 °C.

Comparison of evolution laws of stress and strain fields in hot rolling of titanium alloy large rings with different sizes

For hot rolling of titanium alloy large rings,evolution laws of stress and strain fields in rings with various sizes were explored and compared based on a reliable coupled thermo-mechanical three-dimensional （3D） finite element （FE） model.The results show that for forming processes of different rings,as γ^-（the equivalent distribution ratio of feed amount per revolution of a process） decreases,the final peak Mises stress may transfer from the biting point at the driver roll side to that at the idle roll side,and the final peak equivalent plastic strain may transfer from the outside surface to the inside surface;as L^- （the equivalent deformation zone length of a process） increases,the final peak Mises stress may appear in the middle layer.The final positions of peak Mises stress and equivalent plastic strain are the combined effects of the above two aspects.In the deformation zone of a deformed ring,the surface layers are in the 3D compressive stress state,while the middle layer is in the 1D compressive and 2D tensile stress state or 2D compressive and 1D tensile stress state;the whole ring is in the 1D compressive and 2D tensile strain state.

Analysis of bending on the front end of sheet during hot rolling

The analysis of bending in finishing rolling was performed. An asymmetrical rolling force model was established, and the upper and lower neutral points were determined. Thc bending which resulted from the asymmetrical rolling force at the roll gap was studied and related flexibility equations were proposed according to elastic mechanics. Moreover, material mechanics was used to analyze the effects of temperature difference and self-weight on the bending out of the roll gap, and the flexibility equations were constructed. The main factors on bending were summed up, and the bending rule in the rolling could be obtained. In addition practical calculation was made with the production data of ribbon steel from Laiwu Iron ＆ Steel Group Co. Ltd.

Effects of finishing rolling temperatures and reduction on the mechanical properties of hot rolled multiphase steel

Effects of finishing rolling temperatures and reduction on the mechanical properties of hot rolled multiphase steel were investigated. Thermo-mechanical control processing (TMCP) was conducted by using a laboratory hot rolling mill, in which three different kinds of finishing rolling temperatures and reduction and various austempering times were applied. The results showed that polygonal ferrite, granular bainite and larger amount of stabilized retained austenite can be obtained by controlled rolling processes, and that the strain-induced transformation to martensite from the retained austenite can occur gradually when the steel is deformed during tensile test. Mechanical properties increase with decreasing finishing rolling temperature and increasing amount of deformation. The most TRIP (transformation induced plasticity) effect, and ultimate tensile strength (UTS), total elongation (TEL) and the product of ultimate tensile strength and total elongation (UTS×TEL) are obtained at 20 min.

Deformation Stability of GH4033 Superalloy in the Hot Continuous Rolling Process Based on Dynamic Material Model and Finite Element Model

The flow stress behavior of GH4033 superalloy was determined by the hot compression tests at the temperatures of 1223-1473 K and the total strains of 0.6 with the strain rates of 0.001-30.0 s^(-1) by using cylindrical samples.The processing maps based on the dynamic material model(DMM)combined with the corresponding microstructure observations indicate the reasonable processing domain locating at the strain rates of 0.1-1.0 s^(-1) and the deformation temperature of 1273-1423 K.Meanwhile,the numerical simulation based on finite element model(FEM)described the variation of the effective strain,effective strain rate and the temperature for the core node,and unveiled the influence of the hot rolling parameters considering the initial temperature(T_(0))range of 1223-1473 K and the first-stand biting velocity(v_(0))range of 0.15-0.35 m·s^(-1).Furthermore,the deformation stability of GH4033 superalloy in the round rod hot continuous rolling(HCR)process is described and analyzed by coupling the three-dimensional(3-D)processing map,and the spatial trajectory lines were determined by the numerically simulated temperatures,the strains and the strain rates.Finally,the results show that the hot deformation stability of GH4033 can be achieved by the rolling process parameters located at T_(0)=1423 K and v_(0)=0.25 m·s^(-1).Additionally,the practical HCR processes as T_(0)=1423 K and v_(0)=0.15,0.25,0.35 m·s^(-1) were operated to verify the influence of the hot rolling parameters on the hot deformation stability by the microstructure observation of the final products.

Influence of Hot Rolling Conditions on the Mechanical Properties of Hot Rolled TRIP Steel

Influence of hot rolling conditions on the mechanical properties of hot rolled TRIP steel was investigated. Thermomechanical control processing （TMCP） was conducted by using a laboratory hot rolling mill, in which three different kinds of finish rolling temperatures were applied. The results show that polygonal ferrite, granular bainite and larger amount of stabilized retained austenite can be obtained by controlled rolling processes. The finer ferrite grain size is produced through the deformation induced transformation during deformation rather than after deformation, which affects the mechanical properties of hot rolled TRIP steel. Mechanical properties increase with decreasing finish rolling temperature due to the stabilization of retained austenite. Ultimate tensile strength （UTS）, total elongation （TEL） and the product of ultimate tensile strength and total elongation （UTS×TEL） reaches optimal values （791 MPa, 36% and 28 476 MPa%, respectively） when the specimen was hot rolled for 50% reduction at finish rolling temperature of 700 ℃.

Practice to improve the plate camber during hot rolling by optimizing rolling schedule

Plate camber is one of the most important problems in hot rolling process which not only lead to lower output caused by increasing of crop loss,but also influence on the efficiency of follow-up shear processes,in severe cases damages of side guides or stands also occurred.In terms of reversible four-high hot rolling mills,the main causes of this problem exist in the following areas,reasons of stands,such as the stiffness difference between the drive side and operation side;reasons of slabs,such as the original wedge or the temperature difference along the width direction;reasons of side guides,such as the error of work pieces centerin.In their essence,it can be concluded that the initial deviation of deformation on both sides will increase as the processing,and then the work piece will deviate the center line of the stand,which will form camber defects in the end. The attempt of improving the plate camber was carried out by design the optimized schedules on the bases of theory of the steady rolling conditions during hot rolling process.In presizing and broadsizing sequence,according to the biting conditions and maximum torque restrictions,the rolling reduction of every pass should be as large as possible for the propose of increasing the negative convexity of load-gap through increasing the rolling force. When rolling process goes to finishing stage,it will be impossible to correct rolling centerline in last serval passes because the work pieces will be too long and thin,while considering the bad impact on plate profile which brought by increasing force.Therefore,the main purpose of finishing sequence should be profile control,and slowing down the speed of camber extension as much as possible by gap tilt adjustment automatically. The results show that in hot rolling process,the degree of final camber is impacted by all the three sequences. It is suggested that the control or even eliminating the defect is expectable by a well designed rolling schedule fundamentally.

Shear deformation and plate shape control of hot-rolled aluminium alloy thick plate prepared by asymmetric rolling process

Asymmetric rolling （ASR）, as one of severe plastic deformation （SPD） methods to make ultra-fine materials with enhanced performance is mainly used to prepare foil and thin strip. The asymmetrical rolling was achieved by adjusting the diameters of the upper roll and the bottom roll and was used to prepare hot-rolled thick plate of 5182 aluminium alloy. The shear deformation and plate shape control were experimentally studied. The experimental results show that asymmetrical rolling has a significant effect on metal deformation stream and can somehow refine microstructure and improve the uniformity of microstructure and properties. The asymmetrical rolling process can also reduce the rolling force. However, bending of rolling plate often happens during asymmetrical rolling process. The factors affecting the bending were discussed.

Dynamic explicit FE modeling of hot ring rolling process

A new FE modeling method of hot ring rolling was presented by solving key technologies such as contact and heat boundary conditions,motion control over guide rolls,and mass scaling.The method has the following features:1)the elastic-plastic dynamic explicit approach instead of the static implicit approach is adopted to solve the process so as to greatly improve computational efficiency without sacrificing computational accuracy;2)the coupled thermal-mechanical effect is considered as opposed to the conventional isothermal assumption,which is more practical;3)in contrast to the simplified 2D or local 3D ring model,the full 3D ring is modeled to simulate the process.Based on the FE modeling method,two cases of hot plain ring rolling are simulated in the FEA software ABAQUS/Explicit.The simulation results are compared with the experimental measurements and the good agreement between them is observed regarding the material flow and the temperature distribution of the ring.

Effects of rolling parameters of snake hot rolling on strain distribution of aluminum alloy 7075

The realization way of snake rolling was introduced. Flow velocity, strain and stress distribution of 7075 aluminum alloy plate during snake rolling and symmetrical rolling were analyzed in Deform 3D. Effects of velocity ratio, offset distance between two rolls and pass reduction on the distribution of equivalent strain and shear strain were analyzed. The results show that flow velocity and equivalent strain on the lower layer of the plate are larger than those of the upper layer because of the larger velocity of the lower roll and the gap is increased with the increase of velocity ratio and pass reduction. The shear strain of roiling direction in the center point is almost zero during symmetrical rolling, while it is much larger during snake rolling because of the existence of rub zone. The shear strain is increased with the increase of velocity ratio, offset distance and pass reduction. This additional shear strain is beneficial to improve the in_homogeneous strain distribution.

Rate controlling mechanisms in hot deformation of 7A55 aluminum alloy

The hot deformation behavior of 7A55 aluminum alloy was investigated at the temperature ranging from 300 ℃ to 450 ℃ and strain rate ranging from 0.01 s-1 to 1 s-1 on a Gleeble-3500 simulator. Processing maps were established in order to apprehend the kinetics of hot deformation and the rate controlling mechanism was interpreted by the kinetic rate analysis obeying power-law relation. The results indicated that one significant domain representing dynamic recrystallization （DRX） existed on the processing maps and lying in 410-450 ＆#176;C and 0.05-1 s-1. The conclusions of kinetic analysis correlated well with those obtained from processing maps. The apparent activation energy values calculated in the dynamic recrystallization （DRX） domain and the stability regions except dynamic recrystallization （DRX） domain were 91.2 kJ/mol and 128.8 kJ/mol, respectively, which suggested that grain boundary self-diffusion and cross-slip were the rate controlling mechanisms.