Fault Identification for Shear-Type Structures Using Low-Frequency Vibration Modes

Shear-type structures are common structural forms in industrial and civil buildings,such as concrete and steel frame structures.Fault diagnosis of shear-type structures is an important topic to ensure the normal use of structures.The main drawback of existing damage assessment methods is that they require accurate structural finite element models for damage assessment.However,for many shear-type structures,it is difficult to obtain accurate FEM.In order to avoid finite elementmodeling,amodel-freemethod for diagnosing shear structure defects is developed in this paper.This method only needs to measure a few low-order vibration modes of the structure.The proposed defect diagnosis method is divided into two stages.In the first stage,the location of defects in the structure is determined based on the difference between the virtual displacements derived from the dynamic flexibility matrices before and after damage.In the second stage,damage severity is evaluated based on an improved frequency sensitivity equation.Themain innovations of this method lie in two aspects.The first innovation is the development of a virtual displacement difference method for determining the location of damage in the shear structure.The second is to improve the existing frequency sensitivity equation to calculate the damage degree without constructing the finite elementmodel.Thismethod has been verified on a numerical example of a 22-story shear frame structure and an experimental example of a three-story steel shear structure.Based on numerical analysis and experimental data validation,it is shown that this method only needs to use the low-order modes of structural vibration to diagnose the defect location and damage degree,and does not require finite element modeling.The proposed method should be a very simple and practical defect diagnosis technique in engineering practice.

Experimental study of the effects of a multistage pore-throat structure on the seepage characteristics of sandstones in the Beibuwan Basin:Insights into the flooding mode

To investigate the relationship between grain sizes, seepage capacity, and oil-displacement efficiency in the Liushagang Formation of the Beibuwan Basin, this study identifies the multistage pore-throat structure as a crucial factor through a comparison of oil displacement in microscopic pore-throat experiments. The two-phase flow evaluation method based on the Li-Horne model is utilized to effectively characterize and quantify the seepage characteristics of different reservoirs, closely relating them to the distribution of microscopic pores and throats. It is observed that conglomerate sandstones at different stages exhibit significant heterogeneity and noticeable differences in seepage capacity, highlighting the crucial role played by certain large pore throats in determining seepage capacity and oil displacement efficiency. Furthermore, it was found that the displacement effects of conglomeratic sandstones with strong heterogeneity were inferior to those of conventional homogeneous sandstone, as evidenced by multiple displacement experiments conducted on core samples with varying granularities and flooding systems. Subsequently, core-based experiments on associated gas flooding after water flooding were conducted to address the challenge of achieving satisfactory results in a single displacement mode for reservoirs with significant heterogeneity. The results indicate that the oil recovery rates for associated gas flooding after water flooding increased by 7.3%-16.4% compared with water flooding alone at a gas-oil ratio of approximately 7000 m^(3)/m^(3). Therefore, considering the advantages of gas flooding in terms of seepage capacity, oil exchange ratio, and the potential for two-phase production, gas flooding is recommended as an energy supplement mode for homogeneous reservoirs in the presence of sufficient gas source and appropriate tectonic angle. On the other hand, associated gas flooding after water flooding is suggested to achieve a more favorable development effect compared to a single mode of energy supplementation for strongly heterogeneous sandstone reservoirs.

Electronic Structure Investigation of 12442 Iron-Based Superconductors Based on Block-Layer Model

Superconducting transition temperature(Tc),as a crucial parameter,exploring its relationship with various macroscopic and microscopic factors helps to understand the mechanism of high-temperature superconductivity from multiple perspectives,aiding in a multidimensional comprehension of high-temperature superconductivity mechanisms.Drawing inspiration from the block-layer structure models of cuprate superconductors,we computationally investigated the interlayer interaction energies in the 12442-type iron-based superconducting materials AkCa_(2)Fe_(4)As_(4)F_(2)(Ak=K,Rb,Cs)systems based on the block-layer model and explored their relationship with Tc.We observed that an increase in interlayer combinative energy leads to a decrease in Tc,while conversely,a decrease in interlayer combination energy results in an increase in Tc.Further,we found that the contribution of the Fe 3d band structure,especially the 3dz2 orbital,to charge transfer is significant.

Transition of plasticity and fracture mode of Zr-Al-Ni-Cu bulk metallic glasses with network structures

Effect of network structure on plasticity and fracture mode of Zr？Al？Ni？Cu bulk metallic glasses （BMGs） was investigated. The microstructures of transversal and longitudinal sections were exposed by chemical etching and observed by scanning electron microscopy （SEM）. The mechanical properties were examined by room-temperature uniaxial compression test. The results show that both plasticity and fracture mode are significantly affected by the network structure and the alteration occurs when the size of the network structure reaches up to a critical value. When the cell size （dc） of the network structure is ~3μm, Zr-based BMGs characterize in plasticity that decreases with increasingdc. The fracture mode gradually transforms from single 45° shear fracture to double 45° shear fracture and then cleavage fracture with increasingdc. In addition, the mechanisms of the transition of the plasticity and the fracture mode for these Zr-based BMGs are also discussed.

Analysis on Apple Tree Structures by Free Spindle Pruning Mode

To determine the correlation between the stem taperingness and central shaft by free spindle pruning mode on different apple cultivars, the central shaft growth data of three cultivars of free spindle short shoot ＂Fuji＂, free spindle long shoot ＂Fuji＂, free spindle ＂Huaguan＂ were investigated in Xingtang County of Hebei Province by SPSS analysis. The results showed that the stem taperingness on free spindle short shoot ＂Fuji＂ was in negative correlation with central shaft, but the correlation was not significant. While the stem taperingness on free spindle long shoot ＂Fuji＂ was in positive correlation with central shaft, but the correlation was not significant either. The stern taperingness on free spindle ＂Huaguan＂ was in negative correlation with central shaft, and the correlation between the stem taperingness and the central shaft total length was significant at the level of 0.01. The results.provided scientific theoretical basis for guiding the dwarfing rootstocks close planting apple tree pruning technology.

Application of discrete choice model in trip mode structure forecast:a case study of Bengbu

In order to find the main factors that influence the urban traffic structure,a relational model between the travelers＇ characteristics and the trip mode choice is built.The data of urban residents＇ characteristics are obtained from statistical data,while the trip mode split data is collected through a trip survey in Bengbu.In addition,the discrete choice model is adopted to build the functional relationship between the mode choice and the travelers＇ personal characteristics,as well as family characteristics and trip characteristics.The model shows that the relationship between the mode split and the personal,as well as family and trip characteristics is stable and changes little as the time changes.Deduced by the discrete model,the mode split result is relatively accurate and can be feasibly used for trip mode structure forecasts.Furthermore,the proposed model can also contribute to find the key influencing factors on trip mode choice,and restructure or optimize the urban trip mode structure.

Sliding Mode Variable Structure Control for Visual Servoing System

A visual servoing tracking controller is proposed based on the sliding mode control theory in order to achieve strong robustness against parameter variations and external disturbances. A sliding plane with time delay compensation is presented by the pre-estimate of states. To reduce the chattering of the sliding mode controller, a modified exponential reaching law and hyperbolic tangent function are applied to the design of visual controller and robot joint controller. Simulation results show that the visual servoing control scheme is robust and has good tracking performance.

Research on mode localization of reticulated shell structures

Reticulated shell structures （RSSs） are characterized as cyclically periodic structures. Mistuning of RSSs will induce structural mode localization. Mode localization has the following two features： some modal vectors of the structure change remarkably when the values of its physical parameters （mass or stiffness） have a slight change; and the vibration of some modes is mainly restricted in some local areas of the structure. In this paper, two quantitative assessment indexes are introduced that correspond to these two features. The first feature is studied through a numerical example of a RSS, and its induced causes are analyzed by using the perturbation theory. The analysis showed that internally, mode localization is closely related to structural frequencies and externally, slight changes of the physical parameters of the structure cause instability to the RSS. A scaled model experiment to examine mode localization was carried out on a Kiewit single-layer spherical RSS, and both features of mode localization are studied. Eight tests that measured the changes of the physical parameters were carried out in the experiment. Since many modes make their contribution in structural dynamic response, six strong vibration modes were tested at random in the experimental analysis. The change and localization of the six modes are analyzed for each test. The results show that slight changes to the physical parameters are likely to induce remarkable changes and localization of some modal vectors in the RSSs.

Variable structure control with sliding mode prediction for discrete-time nonlinear systems

A new variable structure control algorithm based on sliding mode prediction for a class of discrete-time nonlinear systems is presented. By employing a special model to predict future sliding mode value, and combining feedback correction and receding horizon optimization methods which are extensively applied on predictive control strategy, a discrete-time variable structure control law is constructed. The closed-loop systems are proved to have robustness to uncertainties with unspecified boundaries. Numerical simulation and pendulum experiment results illustrate that the closed-loop systems possess desired performance, such as strong robustness, fast convergence and chattering elimination.

Moisture Structure of the Quasi-biweekly Mode Revealed by AIRS in Western Pacific

Using Atmospheric Infrared Sounder （AIRS） humidity profiles, rainfall from the Tropical Rainfall Measuring Mission （TRMM） Global Precipitation Index （GPI）, Quick Seatterometer （QSCAT） satellite-observed surface winds, and SST from the Advanced Microwave Scanning Radiometer for NASA＇s Earth Observing System （AMSR_E）, we analyzed the structure of the summer quasi-biweekly mode （QBM） over the western Pacific in 2003-2004. We find that the signal of 10 20-day oscillations in the western Pacific originates from the Philippine Sea, and propagates northwestward toward South China. The AIRS data reveal that the boundary-layer moisture provides preconditioning for QBM propagation, and leads the mid-troposphere moisture during the entire QBM cycle. The positive SST anomaly leads or is in-phase with the boundary- layer moistening, and may be a major contributor. Most likely, the 10 20-day SST anomaly positively feeds back to the atmosphere by moistening the boundary layer, destabilizing the troposphere, and leading the QBM to propagate northwestward in the western North Pacific. However, the ECMWF/TOGA （Tropical Ocean and Global Atmosphere） analysis does not display boundary-layer （BL） moisture anomalies leading the mid-troposphere moisture.

Stable single longitudinal mode erbium-doped silica fiber laser based on an asymmetric linear three-cavity structure

We present a stable linear-cavity single longitudinal mode （SLM） erbium-doped silica fiber laser. It consists of four fiber Bragg gratings （FBGs） directly written in a section of photosensitive erbium-doped fiber （EDF） to form an asymmetric three-cavity structure. The stable SLM operation at a wavelength of 1545.112 nm with a 3-dB bandwidth of 0.012 nm and an optical signal-to-noise ratio （OSNR） of about 60 dB is verified experimentally. Under laboratory conditions, the performance of a power fluctuation of less than 0.05 dB observed from the power meter for 6 h and a wavelength variation of less than 0.01 nm obtained from the optical spectrum analyzer （OSA） for about 1.5 h are demonstrated. The gain fiber length is no longer limited to only several centimeters for SLM operation because of the excellent mode-selecting ability of the asymmetric three-cavity structure. The proposed scheme provides a simple and cost-effective approach to realizing a stable SLM fiber laser.

Optimal variable structure control with sliding modes for unstable processes

In this work,a variable structure control(VSC)technique is proposed to achieve satisfactory robustness for unstable processes.Optimal values of unknown parameters of VSC are obtained using Whale optimization algorithm which was recently reported in literature.Stability analysis has been done to verify the suitability of the proposed structure for industrial processes.The proposed control strategy is applied to three different types of unstable processes including non-minimum phase and nonlinear systems.A comparative study ensures that the proposed scheme gives superior performance over the recently reported VSC system.Furthermore,the proposed method gives satisfactory results for a cart inverted pendulum system in the presence of external disturbance and noise.

Energy evolution and structural health monitoring of coal under different failure modes:An experimental study

Structural instability in underground engineering,especially in coal-rock structures,poses significant safety risks.Thus,the development of an accurate monitoring method for the health of coal-rock bodies is crucial.The focus of this work is on understanding energy evolution patterns in coal-rock bodies under complex conditions by using shear,splitting,and uniaxial compression tests.We examine the changes in energy parameters during various loading stages and the effects of various failure modes,resulting in an innovative energy dissipation-based health evaluation technique for coal.Key results show that coal bodies go through transitions between strain hardening and softening mechanisms during loading,indicated by fluctuations in elastic energy and dissipation energy density.For tensile failure,the energy profile of coal shows a pattern of “high dissipation and low accumulation” before peak stress.On the other hand,shear failure is described by “high accumulation and low dissipation” in energy trends.Different failure modes correlate with an accelerated increase in the dissipation energy before destabilization,and a significant positive correlation is present between the energy dissipation rate and the stress state of the coal samples.A novel mathematical and statistical approach is developed,establishing a dissipation energy anomaly index,W,which categorizes the structural health of coal into different danger levels.This method provides a quantitative standard for early warning systems and is adaptable for monitoring structural health in complex underground engineering environments,contributing to the development of structural health monitoring technology.

Extraction of mode shapes of beam-like structures from the dynamic response of a moving mass

This paper proposes an approach to extract the mode shapes of beam-like structures from the dynamic response of a moving mass. When a mass passes through a beam containing several artificially installed humps, its vertical acceleration can be recorded. After applying fast Fourier transformation to the dynamic response, one can extract the mode shapes of the beam. The surface roughness was neglected compared to the humps and its adverse effect on the extraction was reduced. The passing mass performs as both “exciter” and “massage receiver”;therefore, this method requires only one single accelerometer, making it more convenient and time saving in practice. Moreover, to estimate the possible error in extracting mode shapes, a wavenumber domain filtering technique is used to reconstruct the general profiles of mode shapes. Experimental validation of this approach in laboratory scale was conducted. The experimental results show that the proposed method performs well in extracting lower order mode shapes. It should also be noted that the passing mass can not have a very high velocity (e.g. 80 mm/s), otherwise the mass may jump and separate from the beam, and the proposed method may fail to identify mode shapes.

A novel multi-channel porous structure facilitating mass transport towards highly efficient alkaline water electrolysis

An advantageous porous architecture of electrodes is pivotal in significantly enhancing alkaline water electrolysis(AWE)efficiency by optimizing the mass transport mechanisms.This effect becomes even more pronounced when aiming to achieve elevated current densities.Herein,we employed a rapid and scalable laser texturing process to craft novel multi-channel porous electrodes.Particularly,the obtained electrodes exhibit the lowest Tafel slope of 79 mV dec^(-1)(HER)and 49 mV dec^(-1)(OER).As anticipated,the alkaline electrolyzer(AEL)cell incorporating multi-channel porous electrodes(NP-LT30)exhibited a remarkable improvement in cell efficiency,with voltage drops(from 2.28 to 1.97 V)exceeding 300 mV under 1 A cm^(-1),compared to conventional perforated Ni plate electrodes.This enhancement mainly stemmed from the employed multi-channel porous structure,facilitating mass transport and bubble dynamics through an innovative convection mode,surpassing the traditional convection mode.Furthermore,the NP-LT30-based AEL cell demonstrated exceptional durability for 300 h under 1.0 A cm^(-2).This study underscores the capability of the novel multi-channel porous electrodes to expedite mass transport in practical AWE applications.

The relation between modes of lithologic association and interlayer-gliding structures in coal mine

As a case study of the Panji No.1 Coal Mine in Anhui Province, based on thesite measured and statistical data, summarized the lithologic associations, characteristicsand distribution laws of interlayer-gliding structures and tectonic coal in the No.11-2 coalseams.The results show that 9 modes of lithologic association can form interlayer-glidingstructures.It is more easy for rock slip to occur when the lithologic associations are mainroof + coal seam + immediate floor type, compound roof+immediate roof + coal seam +immediate floor type and immediate roof + coal seam + immediate floor type.Lithologicassociations of roof and floor are the precondition to the formation of interlayer-glidingstructures.

A semi-analytical approach for calculating the equilibrium structure and radial breathing mode frequency of single-walled carbon nanotubes

A semi-analytical model for determining the equilibrium configuration and the radial breathing mode (RBM) frequency of single-wall carbon nanotubes (CNTs) is presented. By taking advantage of the symmetry characteristics, a CNT structure is represented by five independent variables. A line search optimization procedure is employed to determine the equilibrium values of these variables by minimizing the potential energy. With the equilibrium configuration obtained, the semi-analytical model enables an efficient calculation of the RBM frequency of the CNTs. The radius and radial breathing mode frequency results obtained from the semi-analytical approach are compared with those from molecular dynamics (MD) and ab initio calculations. The results demonstrate that the semi-analytical approach offers an efficient and accurate way to determine the equilibrium structure and radial breathing mode frequency of CNTs.

Deformation mode and energy absorption of polycrystal-inspired square-cell lattice structures

Lattice structures are widely used in many engineering fields due to their excellent mechanical properties such as high specific strength and high specific energy absorption(SEA)capacity.In this paper,square-cell lattice structures with different lattice orientations are investigated in terms of the deformation modes and the energy absorption(EA)performance.Finite element(FE)simulations of in-plane compression are carried out,and the theoretical models from the energy balance principle are developed for calculating the EA of these lattice structures.Satisfactory agreement is achieved between the FE simulation results and the theoretical results.It indicates that the 30◦oriented lattice has the largest EA capacity.Furthermore,inspired by the polycrystal microstructure of metals,novel structures of bi-crystal lattices and quad-crystal lattices are developed through combining multiple singly oriented lattices together.The results of FE simulations of compression indicate that the EA performances of symmetric lattice bi-crystals and quad-crystals are better than those of the identical lattice polycrystal counterparts.This work confirms the feasibility of designing superior energy absorbers with architected meso-structures from the inspiration of metallurgical concepts and microstructures.

Antisymmetric quadrupole mode of coherent structures in wall-bounded turbulence

Abstract Experiments were conducted in a water tunnel by tomographic time-resolved particle image velocimetry （Tomo-TRPIV）. The Reynolds number Reo is 2 460 on the base of momentum thickness. According to the physical mechanism of the stretch and compression of multi-scale vortex structures in the wall-bounded turbulence, the topological characteristics of turbulence statistics in logarithmic layer were illustrated by local-averaged velocity structure function. During coherent structures bursting, results reveal that the topological structures of velocity gradients, velocity strain rates and vorticities behave as antisymmetric quadrupole modes. A three-layer antisymmetric quadrupole vortex packet confirms that there is a tight relationship between the outer layer and the near-wall layer.

Short beam shear properties and failure modes of the wood-based X-type lattice sandwich structure

A wood-based X-type lattice sandwich structure was manufactured by insertion-glue method.The birch was used as core,and Oriented Strand Board was used as panel of the sandwich structure.The short beam shear properties and the failure modes of the wood-based X-type lattice sandwich structure with different core direction(vertical and parallel),unit specification(120 mm×60 mm and 60 mm×60 mm),core size(50 mm and 60 mm),and drilling depth(9 mm and 12 mm)were investigated by a short beam shear test and the establishment of a theoretical model to study the equivalent shear modulus and deflection response of the X-type lattice sandwich structure.Results from the short beam shear test and the theoretical model showed that the failure modes of the wood-based X-type lattice sandwich structure were mainly the wrinkling and crushing of the panels under three-point bending load.The experimental values of deflection response of various type specimens were higher than the theoretical values of them.For the core direction of parallel,the smaller the unit specification is,the shorter the core size is,and the deeper the drilling depth is,the greater the short beam shear properties of the wood-based X-type lattice sandwich structure is.