The design of Three Gorges Hydropower Station

Using physical model and numerical simulation techniques, some technical problems were studied systemati- cally, including layout of power station, measures of sediment and floating debris discharging, types of intake, embed- ded types of spiral ease, layout of underground powerhouse tunnel group and block reinforcement. It was optimal in technique and economy with the arrangement of powerhouse at the dam-toe of both banks ＋ underground powerhouse in the right bank, as well as the intake with a single and small orifice. The sediment and debris problems could be solved with disperse sediment ejection and floating debris discharging holes. With the adoption of techniques for spiral cases such as heat and pressure preservation, cushion layer and combined embedding, the stable operation of generating units can be guaranteed. The arrangement of tailrace tunnel with sloping ceiling was better than that of tailrace surge tank. The technical requirements related to the embedding type of spiral case were proposed. The reinforcement of huge unfavorable blocks was discussed and the new idea for block reinforcement using anti-sliding piles and normal compressive stress of structural plane was put forward.

Thermo-hydraulic analysis for SCWR during power-raising phase of startup

The study of thermal characteristics during startup is one of the most important aspects for safety analysis of supercritical water-cooled reactor(SCWR).According to the given sliding pressure mode of SCWR,thermal analysis on temperature-raising phase and power-raising phase of startup are carried out.Considering the radial heterogeneity of power distribution,thermal characteristics for different assemblies during startup are also put forward.The results show that,during temperature-raising phase with core power increased only,the temperature of moderator,coolant and fuel cladding in inner assemblies are increased with little amplitude.During power-raising phase with core power and feed-water flow rate increased,the coolant temperature keeps unchanged,but the moderator temperature is decreased.With a greater variation of power,fuel cladding temperature shows a greater increase.Furthermore,considering the uneven distribution of radial power,thermo-hydraulic characteristics with uneven cladding temperature distribution shows a certain horizontal heterogeneity for different fuel assemblies,which becomes serious as flow rate and power increase.By adjusting flow rate distribution in different fuel assemblies or changing power setting during startup,the cladding temperature difference could be effectively reduced,which provides a certain reference for startup optimization of SCWR.

Engineering Geological Study of Regional Tectonic Stability in the Area of the Longyang Gorge Power Station on the Huanghe (Yellow) River

In the stability study of the regional structures in the area of the Longyang Gorge Hydroelectrical Power Station, a model of the current stress-deformation field of the area was constructed based on analyses of available data of regional surveys and historical earthquakes and field investigations of active faults and ancient earthquakes. This model was examined and verified by physical and mathematical simulation experiments, and quantitative relations and data were obtained.

Review on Commissioning Test of Three Gorges Power Transmission & Substation Project

Holding the greatest power transmission capacity in China, Three Gorges power transmission and substation (T&S) project is an important landmark in the

Power Production Management of Three Gorges Project

The Three Gorges Hydropower Plant is the one with the largest installed capacity in the world today and has a decisive and important influence upon the security of the national power grids. It has been operated stably and supplied the East China, Central China, South China, Sichuan and Chongqing with clean renewable energy. This paper presents the management of the project’s dispatch, operation and maintenance and puts forward new ideas and new methods for the plant management, which may provide valuable references for the operation of oversized hydropower plants.

Power Matching and Energy Efficiency Improvement of Hydraulic Excavator Driven with Speed and Displacement Variable Power Source

Mobile machinery energy efficiency and emission pollution are the national and worldwide issues. This paper contributes in solving these problems by applying a speed variable power source. Unfortunately, almost all of the speed variable systems have the dynamic response problem when the motor starts with full load or heavy load. To address this problem, a hydraulic accumulator is used to balance the load of the power source for assisting starting of the motor and a matching method combined with speed and displacement control of the pump is proposed to improve the energy efficiency and dynamic performance simultaneously under different working conditions. Also, the power source/valve combined control strategy of an independent metering system is designed to realize flow matching of the whole system. Firstly, a test system is established to study the dynamic performance and energy efficiency of the speed variable power source with an auxiliary accumulator. Working performance and energy consumption of the power source under different rotating speeds and different loads are studied. And then, the hydraulic excavator test rig with the proposed system is constructed. Furthermore, the working performance of the excavator with the speed-fixed and speed-variable strategy are studied comparatively. Results show that, compared with fixed-speed strategy, the electric power consumption during the idle period and partial load condition can be reduced about 2.05 kW and 1.37 kW. The energy efficiency of speed variable power source is about 40%-71%, which is higher than that of the fixed-speed power source by 3%–10%.

Variants of Secondary Control with Power Recovery for Loading Hydraulic Driving Device

Current high power load simulators are generally incapable of obtaining both high loading performance and high energy efficiency. Simulators with high energy efficiency are used to simulate static-state load, and those with high dynamic performance typically have low energy efficiency. In this paper, the variants of secondary control（VSC） with power recovery are developed to solve this problem for loading hydraulic driving devices that operate under variable pressure, unlike classical secondary control（CSC） that operates in constant pressure network. Hydrostatic secondary control units are used as the loading components, by which the absorbed mechanical power from the tested device is converted into hydraulic power and then fed back into the tested system through 4 types of feedback passages（FPs）. The loading subsystem can operate in constant pressure network, controlled variable pressure network, or the same variable pressure network as that of the tested device by using different FPs. The 4 types of systems are defined, and their key techniques are analyzed, including work principle, simulating the work state of original tested device, static operation points, loading performance, energy efficiency, and control strategy, etc. The important technical merits of the 4 schemes are compared, and 3 of the schemes are selected, designed, simulated using AMESim and evaluated. The researching results show that the investigated systems can simulate the given loads effectively, realize the work conditions of the tested device, and furthermore attain a high power recovery efficiency that ranges from 0.54 to 0.85, even though the 3 schemes have different loading performances and energy efficiencies. This paper proposes several loading schemes that can achieve both high dynamic performance and high power recovery efficiency.

Dynamics of electromagnetic slip coupling for hydraulic power steering application and its energy-saving characteristics

To improve high-speed road feel and enhance energetic efficiency of hydraulic power steering(HPS) system in heavy-duty vehicles, an electromagnetic slip coupling(ESC) was applied to the steering system, which regulated discharge flow of steering pump to realize variable assist characteristic as well as uniquely transfer on-demand power from engine to steering pump. The model of ESC was established and the dynamic characteristics of ESC were presented by the way of simulation and experiment. Upon the layout of the assist characteristics, output torque of ESC was derived. Based on the ESC model, the output torque characteristics of ESC were simulated under steering situation and straight driving situation, respectively. The consistency of simulated ESC output torque and the one deduced from assist characteristics verifies the correctness of the ESC dynamic model. To illustrate energy saving characteristics of ESC-HPS, energy consumption comparison of ESC-HPS and conventional HPS was carried out qualitatively and quantitatively. It follows that the energy consumption of ESC-HPS decreases by 50% compared with that of HPS.

Dynamic characteristics of hydraulic power steering system with accumulator in load-haul-dump vehicle

Using hydraulic power steering system of model EIMCO 922 load-haul-dump vehicle as a simulation example, the dynamic characteristics of hydraulic power steering system in load-haul-dump vehicle were simulated and discussed with SIMULINK software and hydraulic control theory. The results show that the dynamic characteristics of hydraulic power steering system are improved obviously by using bladder accumulator, the hydraulic power steering system of model EIMCO 922 load-haul-dump vehicle generates vibration at the initial stage under the normal steering condition of pulse input, and its static response time is 0.25 s shorter than that without bladder accumulator. Under the normal steering working condition, the capacity of steering accumulator for absorbing pulse is directly proportional to the cross section area of connecting pipeline, and inversely proportional to the length of connecting pipeline. At the same time, the precharge pressure of nitrogen in steering accumulator should be 60%80% of the rated minimum working pressure of hydraulic power steering system. Under the abnormal steering working condition, the steering cylinder piston may obtain higher motion velocity, and the dynamic response velocity of hydraulic power steering system can be increased by reducing the pressure drop of hydraulic pipelines between the accumulator and steering cylinder and by increasing the rated pressure of hydraulic power steering system, but the dynamic characteristics of hydraulic power steering system in load-haul-dump vehicle have nothing to do with the precharge pressure of nitrogen in steering accumulator.

LVP Modeling and Dynamic Characteristics Prediction of A Hydraulic Power Unit in Deep-Sea

A hydraulic power unit （HPU） is the driving ＂heart＂ of deep-sea working equipment. It is critical to predict its dynamic performances in deep-water before being immerged in the seawater, while the experimental tests by simulating deep-sea environment have many disadvantages, such as expensive cost, long test cycles, and difficult to achieve low-temperature simulation, which is only used as a supplementary means for confirmatory experiment. This paper proposes a novel theoretical approach based on the linear varying parameters （LVP） modeling to foresee the dynamic performances of the driving unit. Firstly, based on the varying environment features, dynamic expressions of the compressibility and viscosity of hydranlic oil are derived to reveal the fluid performances changing. Secondly, models of hydraulic system and electrical system are accomplished respectively through studying the control process and energy transfer, and then LVP models of the pressure and flow rate control is obtained through the electro-hydraulic models integration. Thirdly, dynamic characteristics of HPU are obtained by the model simulating within bounded closed sets of varying parameters. Finally, the developed HPU is tested in a deep-sea imitating hull, and the experimental results are well consistent with the theoretical analysis outcomes, which clearly declare that the LVP modeling is a rational way to foresee dynamic performances of HPU. The research approach and model analysis results can be applied to the predictions of working properties and product designs for other deep-sea hydraulic pump.

A graphic monitoring method for electric power of VVVF hydraulic system

In order to online monitor the running state of variable voltage and variable frequency(VVVF)hydraulic system,this paper presents a graphic monitoring method that fuses the information of variable frequency electric parameters.This paper first analyzes how the voltage and current of the motor stator change with the operation conditions of VVVF hydraulic system.As a result,we draw the relationship between the electric parameters(voltage and current)and power frequency.Then,the signals of the voltage and current are fused as dynamic figures based on the idea of Lissajous figures,and the values of the electric parameters are related to the features of the dynamic figures.Rigorous theoretical analysis establishes the function between the electric power of the variable frequency motor(VFM)and the features of the plotted dynamic figures including area of diagram,area of bounding rectangle,tilt angle,etc.Finally,the effectiveness of the proposed method is verified by two cases,in which the speed of VFM and the load of VVVF hydraulic system are changed.The results show that the increase of the speed of VFM enhances its three-phase electric power,but reduces the tilt angle of the plotted dynamic figures.In addition,as the load of VVVF hydraulic system is increased,the three-phase electric power of VFM and the tilt angle of the plotted dynamic figures are both increased.This paper provides a new way to online monitor the running state of VVVF hydraulic system.

Assessment of Axial Power Peaking Factors in GHARR-1 LEU Core: A Decadal Simulation Analysis

This study aims to thoroughly investigate the axial power peaking factors (PPF) within the low-enriched uranium (LEU) core of the Ghana Research Reactor-1 (GHARR-1). This study uses advanced simulation tools, like the MCNPX code for analysing neutron behavior and the PARET/ANL code for understanding power variations, to get a clearer picture of the reactor’s performance. The analysis covers the initial six years of GHARR-1’s operation and includes projections for its whole 60-year lifespan. We closely observed the patterns of both the highest and average PPFs at 21 axial nodes, with measurements taken every ten years. The findings of this study reveal important patterns in power distribution within the core, which are essential for improving the safety regulations and fuel management techniques of the reactor. We provide a meticulous approach, extensive data, and an analysis of the findings, highlighting the significance of continuous monitoring and analysis for proactive management of nuclear reactors. The findings of this study not only enhance our comprehension of nuclear reactor safety but also carry significant ramifications for sustainable energy progress in Ghana and the wider global context. Nuclear engineering is essential in tackling global concerns, such as the demand for clean and dependable energy sources. Research on optimising nuclear reactors, particularly in terms of safety and efficiency, is crucial for the ongoing advancement and acceptance of nuclear energy.

Groundwater Waves in a Coastal Fractured Aquifer of the Third Phase Qinshan Nuclear Power Engineering Field

Tidal fluctuations of Hangzhou Bay produce progressive pressure waves in adjacent field fractured aquifers, as the pressure waves propagate, groundwater levels and hydraulic gradients continuously fluctuate. The effect of tidal fluctuations on groundwater flow can be determined using the mean hydraulic gradient that can be calculated by comparing mean ground and surface water elevations.Tidal fluctuation is shown to affect the piezometer readings taken in a nearshore fractured aquifer around the nuclear power engineering field. Continuous monitoring of a network of seven piezometers provided relations between the tidal cycle and the piezometer readings. The relations can be expressed in times of a time and amplitude scaling factor. The time lag and the tidal efficiency factor and wavelength are calculated using these parameters. It provides significant scientific basis to prevent tide and groundwater for the nuclear power engineering construction and safety run of nuclear power station in the future.

Tri-state Modulation Power Driving of Electro-hydraulic Proportional Amplifier

Switch electro-hydraulic proportional amplifier（PA） widely employs single switch modulation power driving（SSMPD） or reverse discharging power driving（RDPD） at present. SSMPD has slow dynamic response, and can＇t adjust independently the dither signal＇s amplitude and frequency; RDPD accelerates the current decay; consequently, it increases current ripple and power loss. For the purpose of solving the above mentioned problem, the tri-state modulation power driving（TSMPD） scheme was proposed for improving the performance of power driving. Detailedly, the hardware circuit for the tri-state modulation power driving is designed; the tri-state modulation algorithm is realized by digital signal processor（DSP）. The tri-state modulation power driving is investigated by experiments, comparetive experiments among the single switch modulation power driving（SSMPD）, reverse discharging power driving（RDPD）, and the TSMPD are implemented, and the experimental results demonstrate that the linearity error of TSMDP meets the requirement of PA; the current response of TSMSP is the best; the amplitude of ripple current of the TSMPD can be reduced without increasing frequency of PWM, in addition, dither signal amplitude and frequency can be adjusted independently for each other. It is very meaningful to guide the development of high performance proportional amplifier for high frequency response proportional solenoid.

ANALYSIS OF HYDRAULIC POWER SOURCES DISPOSITION AND ENERGY CONSUMPTION FOR HYDRAULIC DRILL RIG

ＡＮＡＬＹＳＩＳＯＦＨＹＤＲＡＵＬＩＣＰＯＷＥＲＳＯＵＲＣＥＳＤＩＳＰＯＳＩＴＩＯＮＡＮＤＥＮＥＲＧＹＣＯＮＳＵＭＰＴＩＯＮＦＯＲＨＹＤＲＡＵＬＩＣＤＲＩＬＬＲＩＧ￥Ｈｅ，Ｑｉｎｇｈｕａ（ＤｅｐａｒｔｍｅｎｔｏｆＭａｃｈｉｎｅＥｎｇｉｎｅｅｒｉｎｇ，...

Modeling and Simulation of Power Coupling System in Hydraulic Hybrid City Bus

In order to solve the coupling problem of power in Hydraulic Hybrid City Bus (HHB), a hydraulic hybrid power coupling system based on planetary gear transmission principle is proposed in this paper. The system consists of diesel engine, power coupler, hydraulic pump/motor, etc. The realizable operating modes of power coupling system are analyzed in this paper. Under coordination of clutches, the engine driven mode, hydraulic driven mode, hybrid driven mode, hydraulic engine-start mode and braking energy recovery mode are realizable. Based on Lagrange equation, kinetic analysis and kinematics analyses are presented. In addition, the simulation model of the power coupling system is proposed, which includes diesel engine model, power coupler model, hydraulic pump/motor model, etc. The example simulation analysis is proposed under the hybrid driven mode;the results show that the power coupling system proposed in this paper can realize power coupling of hydraulic hybrid city bus. Compared with traditional city bus, the hydraulic hybrid city bus can choose small-displacement engine so as to improve fuel economy and dynamic property.

Control of Hydraulic Power System by Mixed Neural Network PID in Unmanned Walking Platform

To speedily regulate and precisely control a hydraulic power system in a unmanned walking platform(UWP),based on the brief analysis of digital PID and its shortcomings,dual control parameters in a hydraulic power system are given for the precision requirement,and a control strategy for dual relative control parameters in the dual loop PID is put forward,a load and throttle rotation-speed response model for variable pump and gasoline engine is provided according to a physical process,a simplified neural network structure PID is introduced,and formed mixed neural network PID(MNN PID)to control rotation speed of engine and pressure of variable pump,calculation using the back propagation(BP)algorithm and a self-adapted learning step is made,including a mathematic principle and a calculation flow scheme,the BP algorithm of neural network PID is trained and the control effect of system is simulated in Matlab environment,real control effects of engine rotation speed and variable pump pressure are verified in the experimental bench.Results show that algorithm effect of MNN PID is stable and MNN PID can meet the adjusting requirement of control parameters.

FLUID INDUCED HYDRAULIC SYSTEM VIBRATIONOF POWERED SUPPORT

Fluid and solid interaction analysis of hydraulic support under the coming pressure of roof rocks was presented. The mathematical model of the system was proposed and numerical studies by the character line method were carried out.

GAS AND OIL POWER DISTRIBUTION RATIO OF A NEW HYDRAULIC BREAKER

The working principle of a new hydraulic breaker operated jointly by gas and hydraulic flow which has a reasonable structure, high efficiency and long piston life-span, is analyzed, and the optimal power distribution ratio of the sealed nitrogen gas to the high-pressure oil in the process of piston impacting is studied. Through theoretical analysis, optimization simulation and detailed calculation, it is determined that the impact system has optimal mechanical performance and highest efficiency when the distribution ratio φ is between 0.3 and 0.5. The theoretical result is also verified by repeated tests.