Effects of Different Concentrations of Sulfate Ions on Carbonate Crude Oil Desorption:Experimental Analysis and Molecular Simulation

Low salinity water containing sulfate ions can significantly alter the surface wettability of carbonate rocks.Nevertheless,the impact of sulfate concentration on the desorption of oil film on the surface of carbonate rock is still unknown.This study examines the variations in the wettability of the surface of carbonate rocks in solutions containing varying amounts of sodium sulfate and pure water.The problem is addressed in the framework of molecular dynamics simulation(Material Studio software)and experiments.The experiment’s findings demonstrate that sodium sulfate can increase the rate at which oil moisture is turned into water moisture.The final contact angle is smaller than that of pure water.The results of the simulations show that many water molecules travel down the water channel under the influence of several powerful forces,including the electrostatic force,the van der Waals force and hydrogen bond,crowding out the oil molecules on the calcite’s surface and causing the oil film to separate.The relative concentration curve of water and oil molecules indicates that the separation rate of the oil film on the surface of calcite increases with the number of sulfate ions.

Experimental Study on the Chloride Ion Concentration of Cement Pastes Prepared with Limestone Powder

To investigate the impact of limestone powder on the chloride ion concentration coefficient of cement pastes,various techniques such as scanning electron microscopy(SEM),X-ray diffraction(XRD),thermogravimetric analysis(TGA),and mercury-porosimetry(MIP)were employed in this paper.The findings demonstrate that the creation of Friedel's salt is inversely associated with the addition of limestone powder,that is,Friedel's salt production is lessened by adding more limestone powder,however,the coefficient of chloride ion concentration initially decreased and then increased again,as does the porosity,and most likely the pore size as well.The specific surface area of limestone powder has increased,and the content of Friedel’s salt increased first and then decreased.However,the shifting trend of Friedel's salt and chloride ion concentration coefficient is in direct opposition,and the pore structure was therefore significantly enhanced.The results of this study offer robust theoretical backing for the inclusion of limestone powder in concrete and provide a positive assessment of its potential applications.

Investigation of an electrode-driven hydrogen plasma method for in situ cleaning of tin-based contamination

To prolong the service life of optics,the feasibility of in situ cleaning of the multilayer mirror(MLM)of tin and its oxidized contamination was investigated using hydrogen plasma at different power levels.Granular tin-based contamination consisting of micro-and macroparticles was deposited on silicon via physical vapor deposition(PVD).The electrodedriven hydrogen plasma at different power levels was systematically diagnosed using a Langmuir probe and a retarding field ion energy analyzer(RFEA).Moreover,the magnitude of the self-biasing voltage was measured at different power levels,and the peak ion energy was corrected for the difference between the RFEA measurements and the self-biasing voltage(E_(RFEA)-eV_(self)).XPS analysis of O 1s and Sn 3d peaks demonstrated the chemical reduction process after 1 W cleaning.Analysis of surface and cross-section morphology revealed that holes emerged on the upper part of the macroparticles while its bottom remained smooth.Hills and folds appeared on the upper part of the microparticles,confirming the top-down cleaning mode with hydrogen plasma.This study provides an in situ electrode-driven hydrogen plasma etching process for tin-based contamination and will provide meaningful guidance for understanding the chemical mechanism of reduction and etching.

Isothermal hydrogen absorption process of Pd-capped Mg films traced by ion beam techniques and optical methods

Pd-capped nanocrystalline Mg films were prepared by electron beam evaporation and hydrogenated under isothermal conditions to inves-tigate the hydrogen absorption process via ion beam techniques and in situ optical methods.Films were characterized by different techniques such as X-ray diffraction(XRD)and scanning electron microscopy(SEM).Rutherford backscattering spectrometry(RBS)and elastic recoil detection analysis(ERDA)provided a detailed compositional depth profile of the films during hydrogenation.Gas-solid reaction kinetics theory applied to ERDA data revealed a H absorption mechanism controlled by H diffusion.This rate-limiting step was also confirmed by XRD measurements.The diffusion coefficient(D)was also determined via RBS and ERDA,with a value of(1.1±0.1)·10^(−13)cm^(2)/s at 140℃.Results confirm the validity of IBA to monitor the hydrogenation process and to extract the control mechanism of the process.The H kinetic information given by optical methods is strongly influenced by the optical absorption of the magnesium layer,revealing that thinner films are needed to extract further and reliable information from that technique.

Curative effect of hydrogen peroxide combined with silver ion disinfection on pelvic floor dysfunction

BACKGROUND Pelvic floor dysfunction(PFD)is related to muscle fiber tearing during childbirth,negatively impacting postpartum quality of life of parturient.Appropriate and effective intervention is necessary to promote PFD recovery.AIM To analyze the use of hydrogen peroxide and silver ion disinfection for vaginal electrodes in conjunction with comprehensive rehabilitation therapy for postpartum women with PFD.METHODS A total of 59 women with PFD who were admitted to the hospital from May 2019 to July 2022 were divided into two groups:Control group(n=27)received comprehensive rehabilitation therapy and observation group(n=32)received intervention with pelvic floor biostimulation feedback instrument in addition to comprehensive rehabilitation therapy.The vaginal electrodes were disinfected with hydrogen peroxide and silver ion before treatment.Intervention for both groups was started 6 weeks postpartum,and rehabilitation lasted for 3 months.Pelvic floor muscle voltage,pelvic floor muscle strength,vaginal muscle voltage,vaginal muscle tone,pelvic floor function,quality of life,and incidence of postpartum PFD were compared between the two groups.RESULTS Before comprehensive rehabilitation treatment,basic data and pelvic floor function were not significantly different between the two groups.After treatment,the observation group showed significant improvements in the maximum voltage and average voltage of pelvic floor muscles,contraction time of type I and type II fibers,pelvic floor muscle strength,vaginal muscle tone,vaginal muscle voltage,and quality of life(GQOLI-74 reports),compared with the control group.The observation group had lower scores on the pelvic floor distress inventory(PFDI-20)and a lower incidence of postpartum PFD,indicating the effectiveness of the pelvic floor biostimulation feedback instrument in promoting the recovery of maternal pelvic floor function.CONCLUSION The combination of the pelvic floor biostimulation feedback instrument and comprehensive rehabilitation nursing can improve pelvic floor muscle strength,promote the recovery of vaginal muscle tone,and improve pelvic floor function and quality of life.The use of hydrogen peroxide and silver ion disinfectant demonstrated favorable antibacterial efficacy and is worthy of clinical application.

Effect of Sodium Ion Concentration on Hydrogen Production from Sucrose by Anaerobic Hydrogen-producing Granular Sludge

This work evaluated the effects of sodium ion concentration, ranging from 0 to 16000mg·L^-1（Na^＋）, on the conversion of sucrose to hydrogen by a high-activity anaerobic hydrogen-producing granular sludge. At the optimum sodium ion concentration [1000-2000mg·L^-1（Na^＋）] for hydrogen production at 37℃, the maximum sucrose degradation rate, the specific hydrogen production yield and the specific hydrogen production rate were 393.6-413.1mg·L^-1.h^-1, 28.04-28.97ml·g^-1, 7.52-7.83ml·g^-1.h^-1, respectively. The specific production yields of propionate, butyrate and valerate decreased with increasing sodium ion concentration, whereas the specific acetate production yield increased, meanwhile the specific production yields of ethanol and caproate were less than 55.3 and 12.6mg·g^-1, respectively. The hybrid fermentation composition gradually developed from acetate, propionate and butyrate to acetate with the increase in sodium ion concentration.

Effect of Sodium Ion Concentration on Hydrogen Production from Sucrose by Anaerobic Hydrogen-producing Granular Sludge

This work evaluated the effects of sodium ion concentration, ranging from 0 to 16000mg·L-1(Na+), on the conversion of sucrose to hydrogen by a high-activity anaerobic hydrogen-producing granular sludge. At the opti- mum sodium ion concentration [1000—2000mg·L-1(Na+)] for hydrogen production at 37℃, the maximum sucrose degradation rate, the specific hydrogen production yield and the specific hydrogen production rate were 393.6— 413.1mg·L-1·h-1, 28.04—28.97ml·g-1, 7.52—7.83ml·g-1·h-1, respectively. The specific production yields of propionate, butyrate and valerate decreased with increasing sodium ion concentration, whereas the specific acetate production yield increased, meanwhile the specific production yields of ethanol and caproate were less than 55.3 and 12.6mg·g-1, respectively. The hybrid fermentation composition gradually developed from acetate, propionate and butyrate to acetate with the increase in sodium ion concentration.

Relationship between Critical Hydrogen Concentration and Applied Stress for Hydrogen Induced Cracking in 0.2 wt—%C Annealed Plain Steel

1.IntroductionSo far there are few people who studythe relationship between the criticalhydrogen concentration and the stress forhvdrogen induced cracking (CCHIC)quantitatively.Several researchers have cal-culated the CCHIC of steels under no stressby means of H permeation method,but no

Effect of initial substrate and biomass concentrations on anaerobic fermentative hydrogen production in batch reactors

The effects of initial substrate (5-60 g /L) and biomass concentration (0.5-3 g /L) on fermentative hydrogen production by mixed cultures were investigated in batch tests using glucose as substrate.The experimental results showed that the hydrogen production increases as the initial substrate concentration increases from 0 to 25 g /L.It indicated that the shift in the metabolic pathway or in the composition of the bacterial flora occurs.The maximum hydrogen yield of 1.78 mol /mol-glucose is obtained at the substrate concentration of 15 g /L.This study also shows that initial biomass concentration affects the hydrogen yield as the cumulative hydrogen production has been increased with the increase of initial cell concentration up to 1.5 g /L and reached the highest level.The maximum hydrogen yield is obtained at the cell concentration of 1.5 g /L.It indicated that the optimum biomass /substrate ratio,maximizing the hydrogen yield and the hydrogen production rate,is determined to be 0.1 g biomass /g glucose.

Impact of Hydrogen Ion Concentration on Amino Acids Composition of Macadamia Protein: Approached Using Cation-Exchange Chromatography

In the present context, the objective of this study was to synthesize and analyze the content of AA of macadamia protein and the impact of hydrogen ion concentration (pH) on AA composition. The determination of AA mainly by cation-exchange chromatography was also investigated. Reproducible and reliable techniques for quantification and identification of AA usually require derivatization. However, techniques such as AA analyzer are composed of cation-exchange chromatography and other components can sideline the derivatization with significant accuracy. The present analysis revealed a higher concentration of essential amino acids especially acidic AA, Glu and Asp and basic AA, Arg than other AA in macadamia protein. The study constitutes first report of use of bubble chart for evaluation of AA and explaination of AAS. The results may elaborate that the degradation of AA of macadamia protein for extraction of pH 11 is caused by the impact of pH. Moreover, the nutritional values of AA present in macadamia protein could change for the better by adjusting pH of extraction.

Corrosion behavior of micro-arc oxidation coating on AZ91D magnesium alloy in NaCl solutions with different concentrations

Ceramic oxide coatings were prepared on AZ91D magnesium alloys in alkaline silicate solution using micro-arc oxidation（MAO） technique.The corrosion behavior of MAO coating on AZ91D magnesium alloys in NaCl solutions with different concentrations（0.1%,0.5%,1.0%,3.5% and 5.0% in mass fraction） was evaluated by electrochemical measurements and immersion tests.The results showed that the corrosion rate of the MAO coated AZ91D increased with increasing chloride ion concentration.The main form of corrosion failure was localized corrosion for the MAO coated AZ91D immersed in higher concentration NaCl solutions（1.0%,3.5% and 5.0%）,while it was general corrosion in dilute NaCl solutions（0.1% and 0.5%）.Two different stages of the failure process of the MAO coated AZ91D could be identified：1） occurrence of the metastable pits and 2） growth of the pits.Different equivalent circuits were also proposed based on the results of electrochemical impedance spectroscopy（EIS） for the MAO coated AZ91D immersed in different concentrations of NaCl solutions for 120 h.

Hydrogen Concentration of Co-Deposited Carbon Films Produced in the Vicinity of Local Island Divertor in LHD

In international thermonuclear experimental reactor （ITER）, one of major concerns is an in-vessel tritium inventory from a point of safety. It is believed that the carbon-tritium co-deposited film produced by the erosion of carbon diverter walls has a high tritium concentration. However, no systematic evaluation for the tritium concentration has been conducted yet. In the present study, the carbon-hydrogen co-deposited films were prepared at the wall of pumping duct in Local Island Divertor experiments of LHD, in order to evaluate the tritium concentration of the co-deposited films produced in ITER. The hydrogen concentration was obtained by measuring the amount of retained hydrogen in the film and the mass density of the film. The hydrogen concentration of the co-deposited carbon film at the wall not facing to the plasma with a low temperature was extremely high, 1.3 in the atomic ratio of H/C. This value is triple times higher than the previous value obtained so far. The crystal structure of the co-deposited carbon film observed by Raman spectroscopy showed very unique structure （polymeric aC：H）, which is well consistent with the high hydrogen concentration. The present study suggests that the tritium concentration of the co-deposited film in ITER depends on the wall position and becomes quite high as high as T/C-0.65. The results obtained contribute to evaluate the in-vessel tritium inventory owing to the co-deposited carbon films.

A universal thermodynamic model of calculating mass action concentrations for structural units or ion couples in aqueous solutions and its applications in binary and ternary aqueous solutions

A universal thermodynamic model of calculating mass action concentrations for structural units or ion couples in ternary and binary strong electrolyte aqueous solution was developed based on the ion and molecule coexistence theory and verified in four kinds of binary aqueous solutions and two kinds of ternary aqueous solutions. The calculated mass action concentrations of structural units or ion couples in four binary aqueous solutions and two ternary solutions at 298.15 K have good agreement with the reported activity data from literatures after shifting the standard state and concentration unit. Therefore, the calculated mass action concentrations of structural units or ion couples from the developed universal thermodynamic model for ternary and binary aqueous solutions can be applied to predict reaction ability of components in ternary and binary strong electrolyte aqueous solutions. It is also proved that the assumptions applied in the developed thermodynamic model are correct and reasonable, i.e., strong electrolyte aqueous solution is composed of cations and anions as simple ions, H2O as simple molecule and other hydrous salt compounds as complex molecules. The calculated mass action concentrations of structural units or ion couples in ternary and binary strong electrolyte aqueous solutions strictly follow the mass action law.

Detecting H2S Gas Concentration by 1,8-Naphthalimides Fluorescent Probe

针对传统硫化氢检测方法灵敏度低的问题,以1,8-萘酰亚胺为荧光基团,基于H_2S的还原性,通过在荧光分子结构上引入具有氧化性的硝基,合成一种可与硫化氢气体发生氧化还原反应生成有荧光响应的小分子荧光探针。该探针本身荧光十分微弱,且荧光峰值在λ=467nm和λ=522nm处。与H_2S反应之后,522nm处的荧光效应消失,467nm处的荧光效应显著增强。测定小分子荧光探针在通入H_2S气体前后的荧光光谱,分析467nm处的荧光强度与气体浓度关系。结果表明:荧光光谱法检测出的H_2S气体浓度与荧光强度之间存在很强的线性关系,相关系数为0.979 3,最低可检测极限可达0.88×10^(-6 )mol·L^(-1)量级。表明基于1,8-萘酰亚胺衍生物的荧光光谱检测法可为油气田H_2S气体浓度的的快速测定提供参考。

MATHEMATICAL MODELS OF NITROGEN CONCENTRATION PROFILE OF ION NITRIDED LAYERS AND COMPUTER SIMULATION

The mathematical models of the kinetics of the layer growth at different ion nitriding condi- tions of armco iron.steels 45,40Cr,42CrMo and 38CrMoAl have been established.Based on these models the expression of nitrogen concentration profile of ion nitrided layers have been deduced with profile simulating method.They are C_=C_(min)^+(P_4)/(ξ_1-x)+(P_5)/(ξ_(10)~2)(ξ_1-x)~2 C_(γ′)=C_(min)^(γ′)+(P_1)/(ξ_(21))(ξ_2-x)+(P_2)/(ξ_(21)~2)(ξ_2-x)~2 C_α=C_(min)~α+(C_(33))/(C_(33))/(ξ_(32))(ξ_3-x)~3 Using these models,the kinetics of layer growth and the nitrogen concentration profile of ion nitrided layers were sinulated on Apple-Ⅱ computer.Results show that the simulated curves coincide quite well with the experimental data.

Effect of Yb^(3+) concentration on the structures and upconversion luminescence properties of Y_2O_3:Er^(3+) ultrafine phosphors

Y2O3：Er^3＋ ultrafine phosphors with a varying Yb^3＋ ion concentration were prepared by a urea homogeneous precipitation method. The results of XRD show that all the samples are of a pure cubic structure and the average crystallite sizes can be calculated as 45, 34, and 28 nm for Y2O3：Er^3＋ ultrafine phosphors with Yb^3＋ ion concentrations of 0, 10%, and 20%, respectively. The lattice constant and cell volume of the ultrafine phosphors decrease with enhancing Yb^3＋ ion concentration. The upconversion luminescence spectra of all the samples were studied under 980 nm laser excitation. The strong green and red upconversion emission were observed, and attributed to the ^2H11/2→^4I15/2, ^4S3/2 → ^4I15/2 and ^4F9/2 →^4I15/2 transitions of Er^3＋, respectively. The intensity of red emission increases with increasing Yb^3＋ ion concentration. The effect of Yb^3＋ ion concentration on the structures and upconversion luminescence mechanism were discussed.

Factors influencing the concentration of negative air ions during the year in forests and urban green spaces of the Dapeng Peninsula in Shenzhen, China

Negative air ions(NAIs)benefit the mental and physical health of humans,but rapid urbanization can decrease the abundance of NAIs.Quantifying the spatial and seasonal distribution of NAIs and determining the factors that infl uence the concentration during urbanization is thus essential.In the present study of a typical developing urban district in southern China,negative air ion concentrations(NAICs)in 60 forests sites and 30 urban green spaces were quantifi ed on seven consecutive days in each of the four seasons.Large seasonal variations in NAIC were revealed in forests and urban green spaces with trough values in summer.NAIC progressively decreased from forests to urban green spaces and was infl uenced by local land morphology,vegetation characteristics,and climatic factors.The vast,heavily vegetated northeastern region was the richest area for NAIs,whereas the narrow central region(urbanized area)was the poorest,implying dramatic impacts of urbanization on the spatial distribution of NAIs.The relationship between air temperature and NAIC was better fi tted with a quadratic equation than a linear equation.Moreover,the NAIC was more sensitive to local morphology in urban green spaces than in urban forests,indicating the vulnerability of NAIs in urbanized areas.Therefore,the appropriate design of local urban morphology is critical.

Universal thermodynamic model of calculating the mass action concentrations of omponents in a ternary strong electrolyte aqueous solution and its application in the NaCl-KCl-H_2O system

A universal thermodynamic model of calculating the mass action concentrations of components in a ternary strong electrolyte aqueous solution has been developed based on the ion and molecule coexistence theory,and verified in the NaCl-KCl-H2O ternary system at 298.15 K. To compare the difference of the thermodynamic model in binary and ternary strong electrolyte aqueous solutions,the mass action concentrations of components in the NaCl-H2O binary strong electrolyte aqueous solution were also computed at 298.15K. A transformation coefficient was required to compare the calculated mass action concentration and reported activity because they were obtained at different standard states and concentration units. The results show that the transformation coefficients between calculated mass action concentrations and reported activities of the same components change in a very narrow range. The calculated mass action concentrations of components in the NaCl-H2O and NaCl-KCl-H2O systems are in good agreement with the reported activities. This indicates that the developed thermodynamic model can reflect the structural characteristics of solutions,and the mass action concentration also strictly follows the mass action law.

Effects of Trajectory Wind Direction on Ion Concentration of PM_(10)

Objective To study the characterization apportionment of main ion concentrations of PM10 under the influence of trajectory wind direction in London. Methods PM10 samples from 1 May 1995 to 30 October 1995 of Oxford Street of Central London were collected, the metals and anions of which were measured using atomic absorption spectrometry （AAS） and ion chromatography （IC）. Composite trajectories representative of the air mass arriving in London at the same period were calculated based on basic routine back trajectories from the British Atmospheric Data Centre （BADC）. Results Concentration apportionments of main ions were similar when the trajectory was plotted back at 6 h, 12 h, and 24 h, some were obviously different. Mg, Ba, Pb, and Cu had similar peak apportionments at the area 180°-320°, but Zn and Ni at the area of 90°-270°, NO3^- and SO4^2- at the area of 100°-220°. Cl^- concentration peak apportionment was at the area of 220°-300°, which showed that Cl^- mainly came from the North Sea. Conclusion Trajectory wind direction has important effect on ion concentration apportionment of PM10 in London. The ions have similar concentration peak apportionments or their correlation coefficients are statistically significant.

Influence of chloride ion concentration on immersion corrosion behaviour of plasma sprayed alumina coatings on AZ31B magnesium alloy

Corrosion attack of aluminium and magnesium based alloys is a major issue worldwide.The corrosion degradation of an uncoated and atmospheric plasma sprayed alumina(APS)coatings on AZ31B magnesium alloy was investigated using immersion corrosion test in NaCl solutions of different chloride ion concentrations viz.,0.01 M,0.2 M,0.6 M and 1 M.The corroded surface was characterized by an optical microscope and X-ray diffraction.The results showed that the corrosion deterioration of uncoated and coated samples were significantly influenced by chloride ion concentration.The uncoated magnesium and alumina coatings were found to offer a superior corrosion resistance in lower chloride ion concentration NaCl solutions(0.01 M and 0.2 M NaCl).On the other hand the coatings and Mg alloy substrate were found to be highly susceptible to localized damage,and could not provide an effective corrosion protection in solutions containing higher chloride concentrations(0.6 M and 1 M).It was found that the corrosion resistance of the ceramic coatings and base metal gets deteriorated with the increase in the chloride concentrations.