Synthesis and electrochemical performances of high-voltage LiNi_0.5Mn_1.5O_4 cathode materials prepared by hydroxide co-precipitation method

Spherical cathode material LiNi_0.5Mn_1.5O_4 for lithium-ion batteries was synthesized by hydroxide co- precipitation method. X-ray diffraction （XRD）, scanning electron microscopy （SEM） and electrochemical mea- surements were carried out to characterize prepared LiNi_0.5Mn_1.5O_4 cathode material. SEM images show that the LiNi_0.5Mn_1.5O_4 cathode material is constituted by micro-sized spherical particles （with a diameter of around 8 μm）. XRD patterns reveal that the structure of prepared LiNi_0.5Mn_1.5O_4 cathode material belongs to Fd3m space group. Electrochemical tests at 25℃show that the LiNi_0.5Mn_1.5O_4 cathode material prepared after annealing at 600 ℃ has the best electrochemical performances. The initial discharge capacity of prepared cathode material delivers 113.5 mAh·g-1 at 1C rate in the range of 3.50-4.95 V, and the sample retains 96.2% （1.0C） of the initial capacity after 50 cycles. Under different rates with a cutoff voltage range of 3.50-4.95 V at 25℃, the dis- charge capacities of obtained cathode material can be kept at about 145.0 （0.1C）, 126.8 （0.5C）, 113.5 （1.0C） and 112.4mAh·g-1 （2.0C）, the corresponding initial coulomb efficiencies retain above 95.2% （0.1C）, 95.0% （0.5C）, 92.5% （1.0C） and 94.8% （2.0C）, respectively.

Preparation of Rare Earth Hydroxide and Oxide Nanoparticles by Precipitation Method

A series of rare earth hydroxide and oxide nanoparticles have been prepared by precipitation method with alcohol as the dispersive and protective reagent. Transmission electron microscope （TEM） images indicate that the particles are spherical in shape and smaller than 100 nm in size. The crystallite sizes of cubic Ln2O3 have lanthanide shrinking effect, while average crystal lattice distortion rates possess lanthanide swelling effect. The diffraction peak intensity of heavy rare earth oxide nanometer powders is remarkably stronger than that of light rare earth oxide nanometer powders. The variation of diffraction intensity with atomic number presents an inverted W type, forming a double peak structure. Fourier transform infrared （FTIR） spectrums reveal that Ln2O3 nanopowders have higher surface activity than that of ordinary Ln2O3 powders. The UV-vis spectra show that Ln-O bond of these particles is slightly blue-shifted, and its absorption intensity decreases.

Fluorescence and preparation of Sr_2(P_2O_7 ):Ce,Tb phosphate by co-precipitation method

The micron-sized Sr2（P2OT）：Ce,Tb green phosphors were prepared by being annealed at different temperatures with its precursors synthesized by co-pre-cipitates of （NH4）2HPO4 at ambient temperature. The phase structure, grain size, surface morphology, and luminescent properties of phosphors were investigated by X-ray diffraction, scanning electron microscope, trans-mission electron microscope, and fluorescence spectrum. The results show that the product of precursor annealed at 1,100 ℃ is Sr2（P2O7）：Ce,Tb, which belongs to ortho-rhombic phase. The powder is spherical and the size dis-tribution is in micron grade. The sample with the molar ratio of Sr/Tb/Ce of 100.0：0.4：0.6 shows the best fluores-cence effect annealed at 1,100 ℃ for 3 h. The phosphors produce green fluorescence by being excitated with ultra-violet radiation of 254 nm wavelength, and the main emission peak is at 547 nm. The Sr2（P2O7）：Ce,Tb phos-phors synthesized by co-precipitation method of precursors at ambient temperature is a kind of efficient green-emitting phosphors.

Effects of synthesis conditions on the structural and electrochemical properties of layered LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2 cathode material via oxalate co-precipitation method

The uniform layered LiNi1/3Co1/3Mn1/3O2 cathode material for lithium ion batteries was prepared by using （Ni1/3Co1/3Mn1/3）C2O4 as precursor synthesized via oxalate co-precipitation method in air. The effects of calcination temperature and time on the structure and electrochemical properties of the LiNi1/3Co1/3Mn1/3O2 were systemically studied. XRD results revealed that the optimal calcination conditions to prepare the layered LiNi1/3Co1/3Mn1/302 were 950℃ for 15 h. Electrochemical measurement showed that the sample prepared under the such conditions has the highest initial discharge capacity of 160.8 mAh/g and the smallest irreversible capacity loss of 13.5% as well as stable cycling performance at a constant current density of 30 mA/g between 2.5 and 4.3 V versus Li at room temperature.

Preparation and Characterization of Y_3Sc_2Ga_3O_(12) Nano-Polycrystalline Powders by Co-Precipitation Method

In order to grow high-quality gallium garnet crystals,polycrystalline materials were used as starting materials.YSGG precursor was synthesized by co-precipitation method using aqueous ammonia as a precipitator,and the precursor was then sintered at different temperatures.The results showed that the feasible pH range was 8.3～9.84 in the process of co-precipitation reaction.The YSGG precursor and the powders sintered at different temperatures were characterized by IR,XRD and TEM methods.It was found that the precursor transformed to pure YSGG polycrystalline phase at 800 ℃.YSGG nano-polycrystalline powders sintered at 800～1000 ℃ were well dispersed and the sizes of the YSGG grains were about 40～100 nm.

Synthesis of LaPO_4:Ce,Terbium by Co-Precipitation Method

The synthesis of precursor of green phosphors, LaPO4:Ce, Tb, by means of co-precipitation with cocurrent flow feed was studied. The effects of the reaction temperature, the kind and concentration of the acid in the bottom water, and the charging rate on the physical properties, such as particle size, were investigated. It is found that the particle size of the powder is controllable by adjusting acidity in bottom water and charging rate. The powder with diameter size of 3 to 5 μm was obtained. Its XRD and SEM were analyzed. XRD patterns of the as-prepared green phosphor powders display the typical peaks of CePO4. SEM shows that the morphology of powders is ball-shaped.

Preparation and Magnetic Properties of Mn-Zn Ferrites by the Co-precipitation Method

Mn-Zn ferrites （Mn1-xZnxFe2O4） with different compositions were prepared by the coprecipitation method, and the influences of such synthesis conditions as pH value, composition and volume ratio （R） of the mixed solution and NH4HCO3 solution on their microstructures and magnetic properties were discussed. The samples were characterized by X-ray diffraction （XRD） and magnetization measurement instrument. Lattice parameters and average crystalline size of the synthesized materials were calculated from the corresponding XRD patterns with the related software Jade.5. For samples of different pH values, only one phase was found when pH values were 7.0, 8.0 and 9.0. The sample with pH value of 7.0 exhibited the highest saturation magnetic induction, the lowest coercive force, and crystallized best. For samples of different R values with pH value of 7.0, only one phase was observed in all samples, and the sample with R value of 2.3 exhibited the highest saturation magnetic induction and the lowest coercive force. The composition has mainly afected the magnetic properties, and the saturation magnetic induction increases with the increase of the content of Zn （x）, but decreases when x is beyond 0.6. The trend of coercive force is on the contrary. However, no magnetism is exhibited when the x value is up to 0.8.

Characterization and ultraviolet-visible shielding property of samarium-cerium compounds containing Sm_(2)O_(2)S prepared by co-precipitation method

Since ultraviolet(UV)light,as well as blue light,which is part of visible light,is harmful to skin,samarium-cerium compounds containing Sm_(2)O_(2)S were synthesized by co-precipitation method.This kind of compounds blocks not only UV light,but also blue light.The minimum values of average transmittance(360-450 nm)and band gap of samarium-cerium compounds were 8.90%and 2.76 eV,respectively,which were less than 13.96%and 3.01 eV of CeO_(2).Elemental analysis(EA),X-ray diffraction(XRD),Fourier transformation infrared(FTIR),and Raman spectra determined that the samples contained Ce_(4)O_(7),Sm_(2)O_(2)S,Sm_(2)O_(3),and Sm_(2)O_(2)SO_(4).The microstructure of samples was analyzed by scanning and transmission electron microscopies(SEM and TEM).X-ray photoelectron spectrum(XPS)showed that cerium had Ce^(3+)and Ce^(4+) valence states,and oxygen was divided into lattice oxygen and oxygen vacancy,which was the direct cause of the decrease of average transmittance and band gap.

Yttrium-Doped SnO_2 Prepared by Co-Precipitation Method for Lithium-Ion Battery Anodes

SnO2 doped with Y were prepared by co-precipitation method and tested in lithium-ion cells. The structure and morphology of the materials were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). XRD patterns presented that the all the as-prepared materials had tetragonal rutile structure but a second phase (Y2O3) was observed when Y content reached 4%. TEM micrograph indicated that Y doped SnO2 had a small particle size ranging from 20 to 25 nm. The electrochemical properties for an anode active material in lithium-ion batteries were investigated at room temperature, including the observed capacity involved in the first-discharge and the reversible capacity values during subsequent charge-discharge cycles. The as-prepared Y-doped SnO2 exhibited promising electrochemical properties as anodes for lithium-ion batteries.

Synthesis of M1-3xAl2O4:Eu2+x/Dy3+ 2x(M^2+= Sr^2+, Ca^2+ and Ba^2+) phosphors with long-lasting phosphorescence properties via co-precipitation method

The long afterglow fluorescent material of M1-3xAl2O4:Eu2+ x/Dy3+2x(M2+= Sr2+, Ca2+ and Ba2+) phosphors are successfully synthesized by calcining precursor obtained via co-precipitation method at 1300oC for 4 h with reducing atmosphere (20% H2 and 80% N2). The phase evolution, morphology and afterglow fluorescent properties are systematically studied by the various instruments of XRD, FE-SEM, PLE/PL spectroscopy and fluorescence decay analysis. The PL spectra shows that the Sr1-3xAl2O4:Eu2+x/Dy3+ 2x phosphors display vivid green emission at s519 nm (4f65d1!4f7 transition of Eu2+) with monitoring of the maximum excitation wavelength at s334 nm (8S7=2!6IJ transition of Eu2+), among which the optimal concentration of Eu2+ and Dy3+ is 15 at.% and 30 at.%, respectively. The color coordinates and temperature of Sr1-3xAl2O4:Eu2+ x/Dy3+ 2x phosphors are approximately at (s0.27, s0.57) and s6700 K, respectively. On the above basis, the M0:55Al2O4:Eu2+ 0:15/Dy3+ 0:3 (M2+= Ca2+ and Ba2+) phosphors is obtained by the same method. The PL spectra of these phosphors shows the strongest blue emission at s440 nm and cyan emission at s499 nm under s334 nm wavelength excitation, respectively, which are blue shifted comparing to Sr1??3xAl2O4:Eu2+ x/Dy3+ 2x phosphors. The color coordinates and temperatures of M0:55Al2O4:Eu2+ 0:15/Dy3+ 0:3 (M2+= Ca2+ and Ba2+) phosphors are approximately at (s0.18, s0.09), s2000 K and (s0.18, s0.42), s11600 K, respectively. In this work, long afterglow materials of green, blue and cyan aluminates phosphors with excellent properties have been prepared, in order to obtain wide application in the field of night automatic lighting and display.

Green Emitting Phosphor M_3(PO_4)_2∶Ce, Tb (M=Mg, Ca, Sr, Ba) Prepared by Co-Precipitation Method

The M3-3x(PO4)2∶2xCe, xTb(M=Mg, Ca, Sr, Ba) phosphors were prepared by coprecipitation in this paper. Their phase structures, morphologies and luminescent properties were investigated by X-ray diffractometer, field emission scanning electron microscopy and fluorospectrophotometer. The results indicate that the Ce3+ and Tb3+ enteres the host lattice because the XRD patterns of alkaline earth phosphate show no impurity phase, the SEM shows the spherical particles with an average size about 1 μm. The emission and excitation spectra are similar to rare earth phosphate. Concentration quenching of the Sr3(PO4)2∶Ce, Tb emission intensity was not observed even when the Tb3+ increases to 0.05, while the maximum emission intensity appears when x=0.04 in M3-3x(PO4)2∶2xCe, xTb(M=Ca, Ba) emission spectrum.

Preparation and characterization of neodymium hydroxide powder via the hydration method

The preparation of Nd(OH)3 powder by the direct hydration method using Nd2O3 as a raw material was studied,and the effects of stirring mode,H2O and Nd2O3 molar ratio,stirring rate,and reaction time on temperature change and conversion rate in a hydration system were analyzed.The reasonable process conditions for the direct hydration of Nd(OH)3 by Nd2O3 were then determined.Process,morphology,and structure were considered in the preparation of neodymium hydroxide powder,and its composition was investigated by X-ray powder diffraction,scanning electron microscopy,laser particle size analysis,thermogravimetric differential thermal analysis,and chemical analysis.It has been proved that the process is simple and feasible,in line with the concept of modern green chemistry,and the products also meet the market requirements.

Advances in preparation methods and mechanism analysis of layered double hydroxide for lithium-ion batteries and lithium-sulfur batteries

Lithium-ion(Li-ion) battery and lithium-sulfur(Li-S) battery have attracted significant attention as promising components for large-scale energy storage because of high theoretical capacity of Li,excellent energy density or environmental friendness for two kinds of batteries.However,there still exist some respective obstacles for commercial applications,such as limited theoretical capacity,high cost and low conductivity of Li-ion cells or shuttle effect of lithium polysulfides of Li-S cells.As typical twodimensional materials,layered double hydroxides(LDHs) exhibit excellent potential in the field of energy storage due to facile tunability of composition,structure and morphology as well as convenient composite and strong catalytic properties.Consequently,various LDHs toward novel separators or interlayers,cathodes,anodes,and interesting catalytic templates are researched to resolve these challenges.In this review,the recent progress for LDHs applied in Li-ion batteries and Li-S batteries including the synthesis methods,designs and applications is presented and reviewed.Meanwhile,the existing challenges and future perspectives associated with material designs and practical applications of LDHs for these two classes of cells are discussed.WeWe hope that the review can attract more attention and inspire more profound researches toward the LDH-based electrochemical materials for energy storage.

An efficient nano-adsorbent via surfactants/dual surfactants assisted ultrasonic co-precipitation method for sono-removal of monoazo and diazo anionic dyes

To preserve the environment for civilization,we should remove the pollutants like toxic dyes by friendly and cost efficacious method.In this study,the effect of surfactants or mixed surfactants on physicochemical,optical and adsorption properties of ternary mixed oxide CeO_(2)-ZrO_(2)-Al_(2) O_3(CZA) are investigated.The ternary mixed oxide CZA was prepared by surfactants or mixed surfactants assisted ultrasonic coprecipitation method.The physicochemical and optical properties are estimated by different techniques like XRD,TEM,EDX,FTIR,S_(BET) and UV-Vis/DR.The CZA_T and CZA_C have hybrid shapes and high surface area.The adsorption properties of ternary mixed oxides adsorbents were characterized by sono-removing anionic dyes such as Congo red(CR) and Remazol red RB-133(RR).The different factors like contact time,different dye concentrations and temperatures also studied.The kinetics and isotherms applications showed that,the adsorption process was followed pseudo second order kinetics and the Freundlich isotherm model.Also,the adsorption is spontaneous and endothermic process through the thermodynamic study.Finally,the results showed that the ternary mixed oxide nano-adsorbent(CeO_(2)-ZrO_(2)-Al_(2) O_3) is promising and functional materials for anionic dye sweep from wastewater.

Structural and Optical Properties of Mg<SUB>1-x</SUB>Zn<SUB>x</SUB>Fe<SUB>2</SUB>O<SUB>4</SUB>Nano-Ferrites Synthesized Using Co-Precipitation Method

In this work, the Mg1-x Znx Fe2 O4 Nanoferrites (where x = 0.0, 0.2, 0.4, 0.6 and 0.8) was synthesized using co-precipitation method. The investigation of structural and optical properties was carried out for the synthesized samples using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and Ultraviolet visible spectrophotometer (UV-Vis). XRD revealed that the structure of these nanoparticles is spinel with space group Fd3m and crystallite size lies in the range 21.0 - 42.8 nm. Lattice parameter was found to increases with Zn concentration and this may be due to the larger ionic radius of the Zn2+?ion. FTIR spectroscopy confirmed the formation of spinel ferrite and showed the characteristics absorption bands around 612, 1146, 1404, 1649 and 3245 cm-1. The energy band gap was calculated for samples with different ratio and was found to be 4.77, 4.82, 4.86, 4.87 and 4.95 eV. The substitution was resulted in slight increased in the lattice constant and that sequentially may lead to the slightly decreased in the energy gap.

Electron Transport Behavior of Multiferroic Perovskite BiMnO_3 Prepared by Co-Precipitation Method

Perovskite BiMnO_3 samples are successfully synthesized by the co-precipitation method at relatively low pressure and moderate temperature.The temperature dependences of resistivity are measured and systematically investigated.It is shown that the electrical resistivity increases sharply with the decrease of temperature above 210 K and the fitted results demonstrate that the thermally activated conduction model is the dominant conduction mechanism for the electron transport behaviors in this temperature region.A dual conducting mechanism,i.e.,the variable range hopping and thermal activated conduction,is suggested to be responsible for the transport behaviors of BiMnO_3 in the region of 180-200 K.Moreover,the resistivity increases slightly with the decrease of temperature below 180 K and the transport is governed by the variable range hopping mechanism.

STUDIES ON THE REACTION OF SULFUR,SELENIUM AND TELLURIUM WITH SODIUM HYDROXIDE UNDER PHASE TRANSFER CATALYSIS(Ⅱ).A CONVENIENT METHOD FOR THE SYNTHESIS OF BI(ACYL)DISULFIDES

A simple and general method for the synthesis of bi(acyl)disulfides is reported.Sulfur is allowed to react with sodium hydroxide to give sodium disulfide at 65℃ under PTC,which can react with acyl halides to afford bi(acyl)disulfides in good to excellent isolated yields.The effects of solvents and phase transfer catalysts are discussed.

Synthesis of tetramethyl ammonium hydroxide by cell diaphragm electrolytic method

Under the conditions of tetramethyl ammonia chloride (TMAC) used as starting material, Ti-based Dimensionally Stable Anode (DSA), stainless steel used as cathode and Nafion 900 cation membrane as cell diaphragm, this paper studies the synthesis of tetramethyl ammonium hydroxide (TMAH) by cell diaphragm electrolytic method, examining not only the effects of current density, concentration of starting material and cell temperature, on the product purity and current efficiency, but also the effects of electrolyte circulation rate on the service life of Ti-based DSA. The experiment puts forward an optimum processing condition, and experimental findings show that preparing TMAH by using this technique can obtain a current efficiency 74.7% and get product with a purity greater than 99.9%.

Crystal Sizes and Energy Gaps of Cerium Oxide Using Co-Precipitation Method

Co-precipitation was used to prepare cerium oxide nano-particles. The effects of aging temperature and concentration of cobalt ion on the optical property, morphology, and particle size were investigated. The cerium oxide was prepared by adding ammonia solution into a mixed solution of cerium nitrate with cobalt nitrate solutions to obtain a large amount of precipitates and then aged further. Subsequently, the precipitates were kept in an oven for calcination keeping the temperature at 400?C for lasting 24 h. The average size of cerium oxide particles was obtained from the (111) peak in the X-ray diffraction pattern using the Scherrer equation. The crystal sizes obtained were found to be in the range of 11.82 - 13.47 nm. The results showed that the particle size decreased with an increase in the Co ion concentration and decreased with an increase in temperature. The SEM pictures show that the morphology for cerium oxide is granular and/or columnar. It can be seen from UV/Vis absorption spectrum that the maximum absorption peaks were in the range of 334 - 390 nm, depending on the operating conditions. The corresponding energy gaps were observed in the range of 3.18 - 3.71 eV. Subsequently, the Brus equation for the energy gap was discussed. Finally, particle size was correlated with the aging temperature and Co ion concentration.

Preparation of Hierarchically Trimodal-Porous ZSM-5 Composites through Steam-assisted Conversion of Macroporous Aluminosilica Gel with Two Different Quaternary Ammonium Hydroxides

This article presents a detailed structural study of a new spherical Mg Cl2-supported Ti Cl4 Ziegler-Natta catalyst for isotactic propylene polymerization, and researches on the relationship between catalyst structure and polymer properties. The spherical support with the chemical composition of CH3CH2 OMg OCH(CH2Cl)2 has been synthesized from a new dispersion system and is used as the supporting material to prepare Ziegler-Natta catalyst. The XRD analysis indicates that the catalyst is fully activated with δ-Mg Cl2 in the active catalyst. The far-IR spectrometric results confirm again the presence of δ-Mg Cl2 in the active catalyst. Textural property of the active catalyst exhibits high surface area coupled with high porosity. The high activity in propylene polymerization is mainly ascribed to the full activation and the porous structure of the catalyst. Scanning electron microscopy/energy dispersive spectrometer mapping results indicate a uniform titanium distribution throughout the catalyst particles. Particle size analysis shows that the catalyst has a narrow particle size distribution. The perfect spherical shape, uniform titanium distribution and narrow particle size distribution of the catalyst confirm the advantage of polymer particles production with less fines. The solid state 13 C NMR and mid-IR spectroscopic analyses indicate that there exists strong complexation between diisobutyl phthalate and Mg Cl2, which leads to the high isotacticity of polypropylene.