Brittle pro-eutectoid cementite that forms along prior-austenite in hypereutectoid steels is deleterious to mechanical properties. The optimum process parameters which suppress the formation of pro-eutectoid cementite...Brittle pro-eutectoid cementite that forms along prior-austenite in hypereutectoid steels is deleterious to mechanical properties. The optimum process parameters which suppress the formation of pro-eutectoid cementite in hypereutectoid steels with carbon content in the range of 0.8%-1.3% in mass fraction, were investigated. Pro-eutectoid cementite formation is effectively hindered by increasing the deformation temperature and decreasing the amount of strain. Transformation at lower temperatures close to the nose of the cooling-transformation diagram also reduces the tendency of the formation of pro-eutectoid cementite. Control of prior-austenite grain size and grain boundary conditions is important. Due to larger number of nucleation sites, finer prior-austenite grain size results in the acceleration of transformation to pro-eutectoid cementite. However, large prior-austenite and straight boundaries lead to less nucleation sites of pro-eutectoid cementite. The cooling rate and carbon content should be reduced as much as possible. The transformation temperature below 660 °C and the strain of 0.5 at deformation temperature of 850 °C are suggested.展开更多
The microstructure evolution of different cold rolling reductions （from 0 to 81.6%） was studied by SEM （scanning electron microscopy） and TEM （transmission electron microscope）. The study showed that the orienta...The microstructure evolution of different cold rolling reductions （from 0 to 81.6%） was studied by SEM （scanning electron microscopy） and TEM （transmission electron microscope）. The study showed that the orientation multiplicity of pearlitic lamellas resulted in inhomogeneous deformation of different pearlitic lamellas, and with the increase of reduction, the microstructure underwent a course of ＂homogeneity → inhomogeneity → homogeneity＂. The result of XRD （X-ray diffraction） analysis indicated that cementite did not decompose and dissolve into ferrite; the results of the mechanical property test suggested that the relationship between Rp0.2 （yield strength） and ε （true strain） was in good agreement with Hollomon relationship. With the equation Rp0.2 = 1465ε^0.18, the yield strength of the steel in different reductions could be well predicted.展开更多
The precipitation of TiN inclusion during solidification of different carbon content of 0.72%, 0.82% and 0.95% in tire cord steel is thermodynamically studied respectively. The results show that the carbon content has...The precipitation of TiN inclusion during solidification of different carbon content of 0.72%, 0.82% and 0.95% in tire cord steel is thermodynamically studied respectively. The results show that the carbon content has obvious effect on TiN inclusion precipitated in tire cord steel of different strength levels. With the carbon content of tire cord steel increasing, the temperature before solidifying reduced gradually and the required activity product of titanium and nitrogen for TiN inclusion precipitation also declined gradually. With the same condition of initial Ti and N content in liquid steel, the size of TiN inclusion precipitated in tire cord steel of higher carbon content is bigger than that of lower carbon content. In order to control the harmful effects on processability of TiN inclusion precipitated in hypereutectoid tire cord steel of the ultra high strength level, the measures of smelting process must be taken to further reduce the titanium and nitrogen content in liquid steel.展开更多
基金Project(51222405)supported by the National Science Foundation for Outstanding Young Scholars of ChinaProject(51034002)supported by the National Natural Science Foundation of China+1 种基金Project(132002)supported by the Fok Ying Tong Education Foundation,ChinaProject(N120502001)supported by the Basic Scientific Research Operation of Center University of China
文摘Brittle pro-eutectoid cementite that forms along prior-austenite in hypereutectoid steels is deleterious to mechanical properties. The optimum process parameters which suppress the formation of pro-eutectoid cementite in hypereutectoid steels with carbon content in the range of 0.8%-1.3% in mass fraction, were investigated. Pro-eutectoid cementite formation is effectively hindered by increasing the deformation temperature and decreasing the amount of strain. Transformation at lower temperatures close to the nose of the cooling-transformation diagram also reduces the tendency of the formation of pro-eutectoid cementite. Control of prior-austenite grain size and grain boundary conditions is important. Due to larger number of nucleation sites, finer prior-austenite grain size results in the acceleration of transformation to pro-eutectoid cementite. However, large prior-austenite and straight boundaries lead to less nucleation sites of pro-eutectoid cementite. The cooling rate and carbon content should be reduced as much as possible. The transformation temperature below 660 °C and the strain of 0.5 at deformation temperature of 850 °C are suggested.
文摘The microstructure evolution of different cold rolling reductions （from 0 to 81.6%） was studied by SEM （scanning electron microscopy） and TEM （transmission electron microscope）. The study showed that the orientation multiplicity of pearlitic lamellas resulted in inhomogeneous deformation of different pearlitic lamellas, and with the increase of reduction, the microstructure underwent a course of ＂homogeneity → inhomogeneity → homogeneity＂. The result of XRD （X-ray diffraction） analysis indicated that cementite did not decompose and dissolve into ferrite; the results of the mechanical property test suggested that the relationship between Rp0.2 （yield strength） and ε （true strain） was in good agreement with Hollomon relationship. With the equation Rp0.2 = 1465ε^0.18, the yield strength of the steel in different reductions could be well predicted.
文摘The precipitation of TiN inclusion during solidification of different carbon content of 0.72%, 0.82% and 0.95% in tire cord steel is thermodynamically studied respectively. The results show that the carbon content has obvious effect on TiN inclusion precipitated in tire cord steel of different strength levels. With the carbon content of tire cord steel increasing, the temperature before solidifying reduced gradually and the required activity product of titanium and nitrogen for TiN inclusion precipitation also declined gradually. With the same condition of initial Ti and N content in liquid steel, the size of TiN inclusion precipitated in tire cord steel of higher carbon content is bigger than that of lower carbon content. In order to control the harmful effects on processability of TiN inclusion precipitated in hypereutectoid tire cord steel of the ultra high strength level, the measures of smelting process must be taken to further reduce the titanium and nitrogen content in liquid steel.
