The semi-solid slurry of a hypoeutectic Al-Si alloy was manufactured by low superheat pouring and weak electromagnetic stirring. The effects of pouting temperature and stirring power on the semi-solid slurry were inve...The semi-solid slurry of a hypoeutectic Al-Si alloy was manufactured by low superheat pouring and weak electromagnetic stirring. The effects of pouting temperature and stirring power on the semi-solid slurry were investigated. The results indicated that the semi-solid slurry to satisfy rheocasting can be manufactured by low superheat pouring and weak electromagnetic stirring. The pouring temperature (or superheat) and the stirring power remarkably affected the morphology of primary α-Al and the size of primary α-Al, and there is no obvious effect of stirring time on primary α-Al. Compared with the samples made by low superheat pouring with no stirring, the nucleation rate, particle morphology and grain size of primary α-Al in A356 were markedly improved by low superheat pouring and weak electromagnetic stirring. On the condition of weak electromagnetic stirring, the pouring temperature with low superheat can be suitably raised to reach the effectiveness obtained from the lower pouring temperature without stirring.展开更多
Several concepts of the grain refinement mechanism of B on hypoeutectic Al-Si alloys have been adopted: the refining effect of B on the a-AI and eutectic Si with the different additions of Al-B master alloys made at ...Several concepts of the grain refinement mechanism of B on hypoeutectic Al-Si alloys have been adopted: the refining effect of B on the a-AI and eutectic Si with the different additions of Al-B master alloys made at 850℃ was investigated; and the Al-B master alloys formed under different temperature conditions have been studied to explore the morphologies of AIB2 particles; slowly cooled sample with addition of Al-B was made to explore the refinement mechanism. AI-B master alloy can refine not only a-AI, but eutectic Si. Theoretical analysis indicates that, although AIB2 does not take part directly in the nucleation process in pure Al in the presence of Si, it provides a substrate for precipitation of a small content of Si from which a-At will grow without any undercooling. When the temperature decreases to eutectic line, AIB2 subsequently nucleates eutectic Si; AIB2 particles appear in two different morphologies, namely, hexagonal platelet and tetradehedron morphology which depend on the processing temperature conditions.展开更多
Effects of Si content and the addition amount of Al-3B master alloy on the solidification structures of hypoeutectic Al-Si alloys were studied. The addition amounts of the master alloy were 0.2%, 0.4%, 0.7% and 1% (ma...Effects of Si content and the addition amount of Al-3B master alloy on the solidification structures of hypoeutectic Al-Si alloys were studied. The addition amounts of the master alloy were 0.2%, 0.4%, 0.7% and 1% (mass fraction, so as the follows), respectively. The Si content of Al-Si binary alloys investigated varied from 1% to 11%. The observation of macrostructures of non-refined samples showed that 3% Si constitutes a transition point at which the minimum grain size can be obtained. It was also found that Al-3B master alloy can shift the transition point towards a higher Si value when its addition amount increases, making this point appear at 4%, 5% and 6% Si as its addition amount increases up to 0.4%, 0.7% and 1%, respectively.展开更多
The semi-solid slurry of hypoeutectic Al-Si alloy was manufactured by low superheat pouring and weak electromagnetic stirring. The effects of pouring temperature and stirring power on the semi-solid slurry making proc...The semi-solid slurry of hypoeutectic Al-Si alloy was manufactured by low superheat pouring and weak electromagnetic stirring. The effects of pouring temperature and stirring power on the semi-solid slurry making process were investigated. The results indicate that the semi-solid slurry to satisfy rheocasting requirement can be made by a combination of low superheat pouring and weak electromagnetic stirring. The pouring temperature (or superheat) and the stirring power significantly affect the morphology and the size of primary α-Al, while there is no obvious effect of the stirring time on primary α-Al. Compared with the samples made by low superheat pouring without stirring, the nucleation rate, particle morphology and grain size of primary α-Al in A356 Al alloy are markedly improved by a process of applying both low superheat pouring and weak electromagnetic stirring. Under the condition of weak electromagnetic stirring applied, the pouring temperature with low superheat can be equivalently to reach the effectiveness obtained from the even lower pouring temperature without stirring.展开更多
The influence of cooling rate and Fe-containing phases on Sr-modification of Si phases in hypoeutectic Al-Si alloys, a problem with great industrial importance, was investigated. The microstructures of samples were ex...The influence of cooling rate and Fe-containing phases on Sr-modification of Si phases in hypoeutectic Al-Si alloys, a problem with great industrial importance, was investigated. The microstructures of samples were examined using scanning electron microscopy(SEM) with energy-dispersive X-ray spectroscopy(EDX). A new method of electron probe microanalysis(EPMA) map scanning was used to analyze the Sr distribution, which gave quantitative results covering more Si particles. EPMA map scanning, together with SEM with EDX, was also used in analyzing the distribution of Fe phases. Results show that Fe-containing phase was related to the unmodified Si particles in samples with partial modification failure and the plate-like Si phases in samples without modification failure. Such a relationship was further confirmed by the microstructure observation.In conclusion, a partial failure of Sr-modification can be caused by both slow cooling rate and Fe-containing phases.展开更多
The effects of vibration and grain refiner on the microstructure of semisolid slurry of hypoeutectic Al-Si alloy were studied. The impact of vibration on the convection of liquid was conducted by using a system of wat...The effects of vibration and grain refiner on the microstructure of semisolid slurry of hypoeutectic Al-Si alloy were studied. The impact of vibration on the convection of liquid was conducted by using a system of water-particle tracer. The 356 melt at temperature of 630-660 ℃ with or without grain refiner Al-5%Ti-1%B was poured into a metal cup as the vibrating vessel, then it was cooled to 590-610 ℃ in the semisolid zone and kept for some time, subsequently vibration with different frequencies was applied. The results show that the primary α(Al) particles become finer and rounder with the increase of vibration frequency. The slurry with primary α(Al) equivalent particle diameter(EPD) of about 90 μm and average shape coefficient(ASC) of about 0.5 can be prepared under vibration of 20 Hz. With the combined action of vibration and grain refiner Al-5Ti-B, even smaller and rounder spheroids with EPD of about 85 μm and ASC of about 0.6 are obtained.展开更多
Electrolytic low-titanium aluminum (ELTA) was produced by adding TiO2 powder to an industrial aluminum electrolyzer. The grain refining effect of A1-4B master alloy in the hypoeutectic Al-Si alloy prepared by using EL...Electrolytic low-titanium aluminum (ELTA) was produced by adding TiO2 powder to an industrial aluminum electrolyzer. The grain refining effect of A1-4B master alloy in the hypoeutectic Al-Si alloy prepared by using ELTA was investigated, and compared with those of Al-5Ti, A1-5Ti-1B and Al-4B master alloys in the similar alloy prepared by using pure Al. The results indicate that when Al-4B is added to the melt of the alloy prepared by using ELTA in terms of the Ti/B mass ratio of 5:1, the grain refining effect is better than those of Al-5Ti, Al-5Ti-1B and Al-4B master alloys. Thus, using Al-4B to refine the grain of Al-Si alloys prepared by using ELTA will possibly become a feasible way of obtaining Al-Si alloy with homogeneous and fine microstructure.展开更多
The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron mi...The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron microscopy(SEM)and laboratory computed tomography(CT).Results showed that the newly developed AlSi9MnMoV alloy exhibited improved mechanical properties when compared to the AlSi10MnMg alloy.The AlSi9MnMoV alloy,which was designed with trace multicomponent additions,displays a notable grain refining effect in comparison to the AlSi10MnMg alloy.Refining elements Ti,Zr,V,Nb,B promote heterogeneous nucleation and reduce the grain size of primaryα-Al.At a lower slow shot speed,the large ESCs are easier to form and gather,developing into the dendrite net and net-shrinkage.With an increase in slow shot speed,the size and number of ESCs and porosities significantly reduce.In addition,the distribution of ESCs is more dispersed and the net-shrinkage disappears.The tensile property is greatly improved by adopting a higher slow shot speed.The ultimate tensile strength is enhanced from 260.31 MPa to 290.31 MPa(increased by 11.52%),and the elongation is enhanced from 3.72%to 6.34%(increased by 70.52%).展开更多
Effects of mischmetal(RE) and/or Ti modifier on the microstructure including α-Al dendrites, eutectic Si phases and other secondary phases of Al-Si brazing and/or welding alloys were investigated by differential sc...Effects of mischmetal(RE) and/or Ti modifier on the microstructure including α-Al dendrites, eutectic Si phases and other secondary phases of Al-Si brazing and/or welding alloys were investigated by differential scanning calorimetry(DSC), optical microscopy(OM), scanning electron microscopy(SEM). The DSC results showed that an addition of RE decreased the eutectic temperature and caused supercooling, promoting the nucleation of eutectic Si crystals. In addition, the maximum temperature of the first endothermic peak varied with the different RE contents, which had a good correlation with the microstructural modification of the eutectic Si phase. The α-Al dendrites were well refined by increasing the cooling rate or adding 0.08 wt.% of Ti. When 0.05 wt.% RE was added to the Al-5Si-0.08 Ti alloy, the morphology of eutectic Si phase was transformed from coarse platelet to fine fibers and the mechanical properties of the resulting welding rod were well improved. Whereas, when excess RE was added, a large number of β-Fe phases appeared and the aspect ratios of β-Fe phases increased. The morphologies and chemical components of two kinds of RE-containing intermetallic compounds(IMCs) were also discussed.展开更多
Effects of electromagnetic stirring(EMS),ultrasonic treatment(UST)and the combination of EMS and UST(EU)on solidification structure were investigated in hypoeutectic A1-Si alloy.The results indicate that EMS,UST and E...Effects of electromagnetic stirring(EMS),ultrasonic treatment(UST)and the combination of EMS and UST(EU)on solidification structure were investigated in hypoeutectic A1-Si alloy.The results indicate that EMS,UST and EU can refine primary u-A1 and modify eutectic silicon by influencing their nucleation and growth processes.EMS can fracture the dendrite arms and lead to decrease of primary α-Al grain size.It also changes the morphology of eutectic silicon and widens the separation of silicon plates.For UST,the cavitation and acoustic streaming are the principal reasons for the microstructure refinement,which enhance the undercooled and heterogeneous nucleation.EU has combined the features of EMS and UST,hence obtains the best effect on the microstructure evolution.Significant refinement of primary α-Al and evident modification of eutectic silicon are observed with EU.In addition,the mechanism of morphological evolution with EU was preliminarily discussed.展开更多
Aluminum high pressure die casting(HPDC)technology has evolved in the past decades,enabling stronger and larger one-piece casting with significant part consolidation.It also offers a higher design freedom for more mas...Aluminum high pressure die casting(HPDC)technology has evolved in the past decades,enabling stronger and larger one-piece casting with significant part consolidation.It also offers a higher design freedom for more mass-efficient thin-walled body structures.For body structures that require excellent ductility and fracture toughness to be joined with steel sheet via self-piercing riveting(for instance,shock towers and hinge pillars,etc.),a costly T7 heat treatment comprising a solution heat treatment at elevated temperatures(450℃-500℃)followed by an over-ageing heat treatment is needed to optimize microstructure for meeting product requirement.To enable cost-efficient mass production of HPDC body structures,it is important to eliminate the expensive T7 heat treatment without sacrificing mechanical properties.Optimizing die cast alloy chemistry is a potential solution to improve fracture toughness and ductility of the HPDC components.The present study intends to tailor the Mg and Cu additions for a new Al-Si-Cr type die casting alloy(registered as A379 with The Aluminum Association,USA)to achieve the desired tensile properties without using T7 heat treatment.It was found that Cu addition should be avoided,as it is not effective in enhancing strength while degrades tensile ductility.Mg addition is very effective in improving strength and has minor impact on tensile ductility.The investigated Al-Si-Cr alloy with a nominal composition of Al-8.5wt.%Si-0.3wt.%Cr-0.2wt.%Fe shows comparable tensile properties with the T7 treated AlSi10MnMg alloy which is currently used for manufacturing shock towers and hinge pillars.展开更多
Hypoeutectic Fe-Cr-B-C hardfacing alloys with different molybdenum( Mo) contents( The design content was 0,2,3. 3 and 4. 5 wt. %,respectively) were deposited using the flux-cored wire by means of metal active gas arc ...Hypoeutectic Fe-Cr-B-C hardfacing alloys with different molybdenum( Mo) contents( The design content was 0,2,3. 3 and 4. 5 wt. %,respectively) were deposited using the flux-cored wire by means of metal active gas arc welding. The effects of Mo on the refinement of microstructures,eutectic microstructure changes and improvement of wear resistance were investigated. The main results were shown as follows: the added Mo could increase the volume fraction of eutectic microstructure and reduce the size of coarse primary austenite as well as the volume fraction. The carboboride of M3( B,C) could be observed in hypoeutectic Fe-Cr-B-C hardfacing alloys at the Mo design content of ≤2. 0 wt. %,while that of M23( B,C)6was formed when 3. 3 wt. % Mo was added.Additionally,the wear resistance of alloys was increased with the increase in Mo content. Specifically,the highest wear resistance of alloys was achieved at 4. 5 wt. % Mo design content,which was 113. 7% higher than that in alloys without Mo.展开更多
The effects of mixing temperature,i.e.,the temperatures of two precursor melts(pure Al and Al-12Si),on the temperature and solute fields of resultant mixture,the nucleation and growth,and the size and morphology of pr...The effects of mixing temperature,i.e.,the temperatures of two precursor melts(pure Al and Al-12Si),on the temperature and solute fields of resultant mixture,the nucleation and growth,and the size and morphology of primary grains during controlled diffusion solidification(CDS) of Al-8Si alloy were investigated by using simulation and calculation.The results indicate that a lower mixing temperature is helpful for achieving more supercooled microscale Al-rich pockets in the mixture,and increasing the width and supercooling degree of supercooling zone in the Al-rich pockets,and thus,the nucleation rate.The nuclei grow up in nondendritic mode,resulting in spheroidal,at least,nondendritic grains.In a successful CDS,the superheat degrees of the two precursor melts should be limited within several degrees,and it is not necessary to extra stipulate the superheat degree of target alloy melt(Al-8Si) when the requirement about Gibbs energies of the three melts is matched.Subsequent observation on casting microstructures shows that the employed simulation and calculation processes are reasonable and the achieved results are reliable.展开更多
Dynamic mechanical analysis (DMA) was applied to systematically investigate the low frequency damping properties of as-cast hypoeutectic Mg-Ni alloys. The results show that the as-cast hypoeutectic Mg-Ni alloys exhibi...Dynamic mechanical analysis (DMA) was applied to systematically investigate the low frequency damping properties of as-cast hypoeutectic Mg-Ni alloys. The results show that the as-cast hypoeutectic Mg-Ni alloys exhibit high damping capacities. The strain amplitude dependent damping curve has its own special characteristic, in which the damping is strongly related to the strain amplitude. The effect of the eutectic phase on damping and the mechanical properties of as-cast hypoeutectic Mg-Ni alloys were also discussed in detail.展开更多
The microstructure and mechanical properties of Al-14.6Si castings modified by Cu-P master alloy under different conditions were studied with optical microscope(OM) and mechanical testing and simulation(MTS).The r...The microstructure and mechanical properties of Al-14.6Si castings modified by Cu-P master alloy under different conditions were studied with optical microscope(OM) and mechanical testing and simulation(MTS).The results indicate that the Cu-P master alloy possesses not only obvious modification effect,but also longevity effect with more than 8 h on the hypereutectic Al-Si alloy.It is shown from thermal calculation,scanning electron microscope(SEM),and energy dispersive analysis of X-rays(EDAX) that the modification mechanism of Cu-P on primary silicon in the castings is heterogeneous nucleation around AlP particles.The Cu-P master alloy has no or little modifying effect on eutectic silicon,even though it has obvious modification on primary silicon in the castings.This may be because of the fast transformation of eutectic silicon at a very narrow temperature,which will notably weaken the role of AlP particles as heterogeneous nuclei for eutectic silicon.展开更多
An Al-Si-P master alloy has been developed by an in-situ reaction and the electron probe microanalyzer (EPMA) results show that there are many pre-formed AlP particles contained in the master alloy. Silicon introduc...An Al-Si-P master alloy has been developed by an in-situ reaction and the electron probe microanalyzer (EPMA) results show that there are many pre-formed AlP particles contained in the master alloy. Silicon introduced into the system plays an important role in remarkably improving the distribution and content of AlP particles due to their similar crystal structure and lattice parameters. ZL109 alloys have shown fast modification response to the addition of 0.5% Al-15Si-3.5P master alloy at 720℃, with a mass of primary Si precipitating in size of about 15 μm. Also, coarse primary Si grains in AI-30Si alloy can be refined dramatically from 150 μm to 37 μm after the addition of 2.0% Al-15Si-3.5P master alloy at 850℃. The P recovery of the Al-15Si-3.5P master alloy is much higher than that of a Cu-8.5P master alloy due to the pre-formed AlP particles.展开更多
Being used more and more widely in engineering,AlSi alloys comprise about 80%of all kinds of aluminum alloys,which are the most widely utilized nonferrous alloys.Although most Al-Si alloys consist of multiple componen...Being used more and more widely in engineering,AlSi alloys comprise about 80%of all kinds of aluminum alloys,which are the most widely utilized nonferrous alloys.Although most Al-Si alloys consist of multiple components,the eutectics in the structure accounts for 50%-90%of the sum volume of such alloys.Therefore,understanding the modification mechanism and function rules of the AlSi eutectic solidification is the technical key in controlling the structures and properties of such casting alloys.The present paper chiefly reviews recent investigation developments and important conclusions along the lines of the functions of modification elements and their modification mechanism in the eutectic solidification of Al-Si alloys.展开更多
In order to investigate the change in liquid microstructure of Al-Si alloytreated by electric pulse (EP), X-ray diffraction tests with liquid Al-Si alloy and ZL109 alloytreated or not by EP were carried out. The resul...In order to investigate the change in liquid microstructure of Al-Si alloytreated by electric pulse (EP), X-ray diffraction tests with liquid Al-Si alloy and ZL109 alloytreated or not by EP were carried out. The results show that the number of Al-Si atomic clustersdecreases and that of Al-Al and Si-Si atomic clusters increases for the treated samples. The testswith ZL109 alloy indicate that a large amount of primary crystal Si appears in the solidifiedmicrostructure after treated by EP. It is found that EP can change the microstructure of liquidmetal by affecting the probability of electrons appearing in different atoms (Al and Si) in theliquid metal. The combining force of different atoms decreases relatively, and that of the sameatoms increases, which is the main reason of reducing the atomic cluster with different atoms(Al-Si) and increasing the atomic cluster with the same atoms (Al-Al, Si-Si). The increasing of theatomic cluster with the same atom cluster resulted in the increasing of Si activity and the higherpoint of eutectics in the phase diagram. It makes a lot of primary silicon appeared in ZL109 alloy.展开更多
An electromagnetic vibration was generated by simultaneously imposing a strong static magnetic field (up to 10 T) and an alternative electricity current to the metal. Its effects on the solidification structure of e...An electromagnetic vibration was generated by simultaneously imposing a strong static magnetic field (up to 10 T) and an alternative electricity current to the metal. Its effects on the solidification structure of eutectic Al-Si alloy have been investigated experimentally. It is found that the eutectic structure has been refined by solely imposing high magnetic field while it is coarsened under the electromagnetic vibration. Furthermore, polyhedral Si grains and non-dendritic α-Al appeared when the electromagnetic vibration strength was strong enough. The refining of eutectic structure is attributed to the decrease of diffusion coefficient caused by the strong magnetic field. The coarseness of eutectic structure may be attributed to the convection caused by electromagnetic vibration. Strong convection may break co-operative growth of eutectic phases to form polyhedral Si grains and non-dendritic α-Al.展开更多
The cast Al-Si alloy was fabricated using the Additive Pressure Casting(APC)method.The effects of holding pressure from 50 to 400 k Pa on the density,cooling rate,and mechanical properties of the alloy,and the corresp...The cast Al-Si alloy was fabricated using the Additive Pressure Casting(APC)method.The effects of holding pressure from 50 to 400 k Pa on the density,cooling rate,and mechanical properties of the alloy,and the corresponding mechanism were discussed.The results indicate that the application of high holding pressure(300 k Pa)enhances the feeding ability of the alloy,leading to an increase of the density.Meanwhile,the cooling rate of the alloy is increased by 100%.In addition,the tensile testing results show that the increase of holding pressure from 50 to 300 k Pa improves the tensile strength and elongation of the alloy by 6.2%and 81.3%,respectively.However,excessive holding pressure(400 k Pa)might lower the density and cooling rate of the alloy due to the feeding channels being blocked.展开更多
基金The project was financially supported by the Hi-tech Research and Development Program of China (No. G2002AA336080) and the National Natural Science Foundation of China (No. 50374012)
文摘The semi-solid slurry of a hypoeutectic Al-Si alloy was manufactured by low superheat pouring and weak electromagnetic stirring. The effects of pouting temperature and stirring power on the semi-solid slurry were investigated. The results indicated that the semi-solid slurry to satisfy rheocasting can be manufactured by low superheat pouring and weak electromagnetic stirring. The pouring temperature (or superheat) and the stirring power remarkably affected the morphology of primary α-Al and the size of primary α-Al, and there is no obvious effect of stirring time on primary α-Al. Compared with the samples made by low superheat pouring with no stirring, the nucleation rate, particle morphology and grain size of primary α-Al in A356 were markedly improved by low superheat pouring and weak electromagnetic stirring. On the condition of weak electromagnetic stirring, the pouring temperature with low superheat can be suitably raised to reach the effectiveness obtained from the lower pouring temperature without stirring.
基金Shandong Natural Foundation !(Grant No:Z99F01)the Natiotal Natals Science Foundation of China !(Grant NO.59671046).
文摘Several concepts of the grain refinement mechanism of B on hypoeutectic Al-Si alloys have been adopted: the refining effect of B on the a-AI and eutectic Si with the different additions of Al-B master alloys made at 850℃ was investigated; and the Al-B master alloys formed under different temperature conditions have been studied to explore the morphologies of AIB2 particles; slowly cooled sample with addition of Al-B was made to explore the refinement mechanism. AI-B master alloy can refine not only a-AI, but eutectic Si. Theoretical analysis indicates that, although AIB2 does not take part directly in the nucleation process in pure Al in the presence of Si, it provides a substrate for precipitation of a small content of Si from which a-At will grow without any undercooling. When the temperature decreases to eutectic line, AIB2 subsequently nucleates eutectic Si; AIB2 particles appear in two different morphologies, namely, hexagonal platelet and tetradehedron morphology which depend on the processing temperature conditions.
基金The work was financially supported by the Open Funds sponsored by Tsinghua University.
文摘Effects of Si content and the addition amount of Al-3B master alloy on the solidification structures of hypoeutectic Al-Si alloys were studied. The addition amounts of the master alloy were 0.2%, 0.4%, 0.7% and 1% (mass fraction, so as the follows), respectively. The Si content of Al-Si binary alloys investigated varied from 1% to 11%. The observation of macrostructures of non-refined samples showed that 3% Si constitutes a transition point at which the minimum grain size can be obtained. It was also found that Al-3B master alloy can shift the transition point towards a higher Si value when its addition amount increases, making this point appear at 4%, 5% and 6% Si as its addition amount increases up to 0.4%, 0.7% and 1%, respectively.
基金The paper is supported by the Hi-tech Research and Develop-ment Program of China (Authorized No.: G2002AA336080), andthe National Natural Science Foundation of China (AuthorizedNo.: 50374012).
文摘The semi-solid slurry of hypoeutectic Al-Si alloy was manufactured by low superheat pouring and weak electromagnetic stirring. The effects of pouring temperature and stirring power on the semi-solid slurry making process were investigated. The results indicate that the semi-solid slurry to satisfy rheocasting requirement can be made by a combination of low superheat pouring and weak electromagnetic stirring. The pouring temperature (or superheat) and the stirring power significantly affect the morphology and the size of primary α-Al, while there is no obvious effect of the stirring time on primary α-Al. Compared with the samples made by low superheat pouring without stirring, the nucleation rate, particle morphology and grain size of primary α-Al in A356 Al alloy are markedly improved by a process of applying both low superheat pouring and weak electromagnetic stirring. Under the condition of weak electromagnetic stirring applied, the pouring temperature with low superheat can be equivalently to reach the effectiveness obtained from the even lower pouring temperature without stirring.
基金supported by the International Science & Technology Cooperation Program of China(No.2015DFR50470)
文摘The influence of cooling rate and Fe-containing phases on Sr-modification of Si phases in hypoeutectic Al-Si alloys, a problem with great industrial importance, was investigated. The microstructures of samples were examined using scanning electron microscopy(SEM) with energy-dispersive X-ray spectroscopy(EDX). A new method of electron probe microanalysis(EPMA) map scanning was used to analyze the Sr distribution, which gave quantitative results covering more Si particles. EPMA map scanning, together with SEM with EDX, was also used in analyzing the distribution of Fe phases. Results show that Fe-containing phase was related to the unmodified Si particles in samples with partial modification failure and the plate-like Si phases in samples without modification failure. Such a relationship was further confirmed by the microstructure observation.In conclusion, a partial failure of Sr-modification can be caused by both slow cooling rate and Fe-containing phases.
基金Project(50775086) supported by the National Natural Science Foundation of ChinaProject (2007AA03Z557) supported by the Hi-tech Research and Development Program of China
文摘The effects of vibration and grain refiner on the microstructure of semisolid slurry of hypoeutectic Al-Si alloy were studied. The impact of vibration on the convection of liquid was conducted by using a system of water-particle tracer. The 356 melt at temperature of 630-660 ℃ with or without grain refiner Al-5%Ti-1%B was poured into a metal cup as the vibrating vessel, then it was cooled to 590-610 ℃ in the semisolid zone and kept for some time, subsequently vibration with different frequencies was applied. The results show that the primary α(Al) particles become finer and rounder with the increase of vibration frequency. The slurry with primary α(Al) equivalent particle diameter(EPD) of about 90 μm and average shape coefficient(ASC) of about 0.5 can be prepared under vibration of 20 Hz. With the combined action of vibration and grain refiner Al-5Ti-B, even smaller and rounder spheroids with EPD of about 85 μm and ASC of about 0.6 are obtained.
基金Project (0322020600) supported by the Science and Technology Foundation of Henan Province, China
文摘Electrolytic low-titanium aluminum (ELTA) was produced by adding TiO2 powder to an industrial aluminum electrolyzer. The grain refining effect of A1-4B master alloy in the hypoeutectic Al-Si alloy prepared by using ELTA was investigated, and compared with those of Al-5Ti, A1-5Ti-1B and Al-4B master alloys in the similar alloy prepared by using pure Al. The results indicate that when Al-4B is added to the melt of the alloy prepared by using ELTA in terms of the Ti/B mass ratio of 5:1, the grain refining effect is better than those of Al-5Ti, Al-5Ti-1B and Al-4B master alloys. Thus, using Al-4B to refine the grain of Al-Si alloys prepared by using ELTA will possibly become a feasible way of obtaining Al-Si alloy with homogeneous and fine microstructure.
基金financially supported by the National Key Research and Development Program of China(2022YFB3404201)the Major Science and Technology Project of Changchun City,Jilin Province(Grant No.20210301024GX)。
文摘The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron microscopy(SEM)and laboratory computed tomography(CT).Results showed that the newly developed AlSi9MnMoV alloy exhibited improved mechanical properties when compared to the AlSi10MnMg alloy.The AlSi9MnMoV alloy,which was designed with trace multicomponent additions,displays a notable grain refining effect in comparison to the AlSi10MnMg alloy.Refining elements Ti,Zr,V,Nb,B promote heterogeneous nucleation and reduce the grain size of primaryα-Al.At a lower slow shot speed,the large ESCs are easier to form and gather,developing into the dendrite net and net-shrinkage.With an increase in slow shot speed,the size and number of ESCs and porosities significantly reduce.In addition,the distribution of ESCs is more dispersed and the net-shrinkage disappears.The tensile property is greatly improved by adopting a higher slow shot speed.The ultimate tensile strength is enhanced from 260.31 MPa to 290.31 MPa(increased by 11.52%),and the elongation is enhanced from 3.72%to 6.34%(increased by 70.52%).
基金Project supported by National Natural Science Foundation of China(51375233)Priority Academic Program Development(PAPD)of Jiangsu Higher Education InstitutionsChina Postdoctoral Science Foundation(2014M550289,2015T80548)
文摘Effects of mischmetal(RE) and/or Ti modifier on the microstructure including α-Al dendrites, eutectic Si phases and other secondary phases of Al-Si brazing and/or welding alloys were investigated by differential scanning calorimetry(DSC), optical microscopy(OM), scanning electron microscopy(SEM). The DSC results showed that an addition of RE decreased the eutectic temperature and caused supercooling, promoting the nucleation of eutectic Si crystals. In addition, the maximum temperature of the first endothermic peak varied with the different RE contents, which had a good correlation with the microstructural modification of the eutectic Si phase. The α-Al dendrites were well refined by increasing the cooling rate or adding 0.08 wt.% of Ti. When 0.05 wt.% RE was added to the Al-5Si-0.08 Ti alloy, the morphology of eutectic Si phase was transformed from coarse platelet to fine fibers and the mechanical properties of the resulting welding rod were well improved. Whereas, when excess RE was added, a large number of β-Fe phases appeared and the aspect ratios of β-Fe phases increased. The morphologies and chemical components of two kinds of RE-containing intermetallic compounds(IMCs) were also discussed.
基金Item Sponsored by National Natural Science Foundation of China[No.50874022]
文摘Effects of electromagnetic stirring(EMS),ultrasonic treatment(UST)and the combination of EMS and UST(EU)on solidification structure were investigated in hypoeutectic A1-Si alloy.The results indicate that EMS,UST and EU can refine primary u-A1 and modify eutectic silicon by influencing their nucleation and growth processes.EMS can fracture the dendrite arms and lead to decrease of primary α-Al grain size.It also changes the morphology of eutectic silicon and widens the separation of silicon plates.For UST,the cavitation and acoustic streaming are the principal reasons for the microstructure refinement,which enhance the undercooled and heterogeneous nucleation.EU has combined the features of EMS and UST,hence obtains the best effect on the microstructure evolution.Significant refinement of primary α-Al and evident modification of eutectic silicon are observed with EU.In addition,the mechanism of morphological evolution with EU was preliminarily discussed.
文摘Aluminum high pressure die casting(HPDC)technology has evolved in the past decades,enabling stronger and larger one-piece casting with significant part consolidation.It also offers a higher design freedom for more mass-efficient thin-walled body structures.For body structures that require excellent ductility and fracture toughness to be joined with steel sheet via self-piercing riveting(for instance,shock towers and hinge pillars,etc.),a costly T7 heat treatment comprising a solution heat treatment at elevated temperatures(450℃-500℃)followed by an over-ageing heat treatment is needed to optimize microstructure for meeting product requirement.To enable cost-efficient mass production of HPDC body structures,it is important to eliminate the expensive T7 heat treatment without sacrificing mechanical properties.Optimizing die cast alloy chemistry is a potential solution to improve fracture toughness and ductility of the HPDC components.The present study intends to tailor the Mg and Cu additions for a new Al-Si-Cr type die casting alloy(registered as A379 with The Aluminum Association,USA)to achieve the desired tensile properties without using T7 heat treatment.It was found that Cu addition should be avoided,as it is not effective in enhancing strength while degrades tensile ductility.Mg addition is very effective in improving strength and has minor impact on tensile ductility.The investigated Al-Si-Cr alloy with a nominal composition of Al-8.5wt.%Si-0.3wt.%Cr-0.2wt.%Fe shows comparable tensile properties with the T7 treated AlSi10MnMg alloy which is currently used for manufacturing shock towers and hinge pillars.
文摘Hypoeutectic Fe-Cr-B-C hardfacing alloys with different molybdenum( Mo) contents( The design content was 0,2,3. 3 and 4. 5 wt. %,respectively) were deposited using the flux-cored wire by means of metal active gas arc welding. The effects of Mo on the refinement of microstructures,eutectic microstructure changes and improvement of wear resistance were investigated. The main results were shown as follows: the added Mo could increase the volume fraction of eutectic microstructure and reduce the size of coarse primary austenite as well as the volume fraction. The carboboride of M3( B,C) could be observed in hypoeutectic Fe-Cr-B-C hardfacing alloys at the Mo design content of ≤2. 0 wt. %,while that of M23( B,C)6was formed when 3. 3 wt. % Mo was added.Additionally,the wear resistance of alloys was increased with the increase in Mo content. Specifically,the highest wear resistance of alloys was achieved at 4. 5 wt. % Mo design content,which was 113. 7% higher than that in alloys without Mo.
基金supported by the National Key Research and Development Program of China (Grant No.2018YFB2001800)。
文摘The effects of mixing temperature,i.e.,the temperatures of two precursor melts(pure Al and Al-12Si),on the temperature and solute fields of resultant mixture,the nucleation and growth,and the size and morphology of primary grains during controlled diffusion solidification(CDS) of Al-8Si alloy were investigated by using simulation and calculation.The results indicate that a lower mixing temperature is helpful for achieving more supercooled microscale Al-rich pockets in the mixture,and increasing the width and supercooling degree of supercooling zone in the Al-rich pockets,and thus,the nucleation rate.The nuclei grow up in nondendritic mode,resulting in spheroidal,at least,nondendritic grains.In a successful CDS,the superheat degrees of the two precursor melts should be limited within several degrees,and it is not necessary to extra stipulate the superheat degree of target alloy melt(Al-8Si) when the requirement about Gibbs energies of the three melts is matched.Subsequent observation on casting microstructures shows that the employed simulation and calculation processes are reasonable and the achieved results are reliable.
基金Projects(50571081 50671083) supported by the National Natural Science Foundation of China+1 种基金 Project(04G53042) supported by the Aeronautical Foundation of ChinaProject(2007E101) supported by the Natural Science Foundation of Shaanxi Province, China
文摘Dynamic mechanical analysis (DMA) was applied to systematically investigate the low frequency damping properties of as-cast hypoeutectic Mg-Ni alloys. The results show that the as-cast hypoeutectic Mg-Ni alloys exhibit high damping capacities. The strain amplitude dependent damping curve has its own special characteristic, in which the damping is strongly related to the strain amplitude. The effect of the eutectic phase on damping and the mechanical properties of as-cast hypoeutectic Mg-Ni alloys were also discussed in detail.
文摘The microstructure and mechanical properties of Al-14.6Si castings modified by Cu-P master alloy under different conditions were studied with optical microscope(OM) and mechanical testing and simulation(MTS).The results indicate that the Cu-P master alloy possesses not only obvious modification effect,but also longevity effect with more than 8 h on the hypereutectic Al-Si alloy.It is shown from thermal calculation,scanning electron microscope(SEM),and energy dispersive analysis of X-rays(EDAX) that the modification mechanism of Cu-P on primary silicon in the castings is heterogeneous nucleation around AlP particles.The Cu-P master alloy has no or little modifying effect on eutectic silicon,even though it has obvious modification on primary silicon in the castings.This may be because of the fast transformation of eutectic silicon at a very narrow temperature,which will notably weaken the role of AlP particles as heterogeneous nuclei for eutectic silicon.
基金supported by the National Science Fund for Distinguished Young Scholars (No. 50625101)the Key Project of Science and Technology Research of the Ministry of Education of China (No. 106103)
文摘An Al-Si-P master alloy has been developed by an in-situ reaction and the electron probe microanalyzer (EPMA) results show that there are many pre-formed AlP particles contained in the master alloy. Silicon introduced into the system plays an important role in remarkably improving the distribution and content of AlP particles due to their similar crystal structure and lattice parameters. ZL109 alloys have shown fast modification response to the addition of 0.5% Al-15Si-3.5P master alloy at 720℃, with a mass of primary Si precipitating in size of about 15 μm. Also, coarse primary Si grains in AI-30Si alloy can be refined dramatically from 150 μm to 37 μm after the addition of 2.0% Al-15Si-3.5P master alloy at 850℃. The P recovery of the Al-15Si-3.5P master alloy is much higher than that of a Cu-8.5P master alloy due to the pre-formed AlP particles.
文摘Being used more and more widely in engineering,AlSi alloys comprise about 80%of all kinds of aluminum alloys,which are the most widely utilized nonferrous alloys.Although most Al-Si alloys consist of multiple components,the eutectics in the structure accounts for 50%-90%of the sum volume of such alloys.Therefore,understanding the modification mechanism and function rules of the AlSi eutectic solidification is the technical key in controlling the structures and properties of such casting alloys.The present paper chiefly reviews recent investigation developments and important conclusions along the lines of the functions of modification elements and their modification mechanism in the eutectic solidification of Al-Si alloys.
文摘In order to investigate the change in liquid microstructure of Al-Si alloytreated by electric pulse (EP), X-ray diffraction tests with liquid Al-Si alloy and ZL109 alloytreated or not by EP were carried out. The results show that the number of Al-Si atomic clustersdecreases and that of Al-Al and Si-Si atomic clusters increases for the treated samples. The testswith ZL109 alloy indicate that a large amount of primary crystal Si appears in the solidifiedmicrostructure after treated by EP. It is found that EP can change the microstructure of liquidmetal by affecting the probability of electrons appearing in different atoms (Al and Si) in theliquid metal. The combining force of different atoms decreases relatively, and that of the sameatoms increases, which is the main reason of reducing the atomic cluster with different atoms(Al-Si) and increasing the atomic cluster with the same atoms (Al-Al, Si-Si). The increasing of theatomic cluster with the same atom cluster resulted in the increasing of Si activity and the higherpoint of eutectics in the phase diagram. It makes a lot of primary silicon appeared in ZL109 alloy.
基金supported by the National Natural Science Foundation of China(No.59871026)
文摘An electromagnetic vibration was generated by simultaneously imposing a strong static magnetic field (up to 10 T) and an alternative electricity current to the metal. Its effects on the solidification structure of eutectic Al-Si alloy have been investigated experimentally. It is found that the eutectic structure has been refined by solely imposing high magnetic field while it is coarsened under the electromagnetic vibration. Furthermore, polyhedral Si grains and non-dendritic α-Al appeared when the electromagnetic vibration strength was strong enough. The refining of eutectic structure is attributed to the decrease of diffusion coefficient caused by the strong magnetic field. The coarseness of eutectic structure may be attributed to the convection caused by electromagnetic vibration. Strong convection may break co-operative growth of eutectic phases to form polyhedral Si grains and non-dendritic α-Al.
基金National Key Research Project of China(No.2016YFB0300901).
文摘The cast Al-Si alloy was fabricated using the Additive Pressure Casting(APC)method.The effects of holding pressure from 50 to 400 k Pa on the density,cooling rate,and mechanical properties of the alloy,and the corresponding mechanism were discussed.The results indicate that the application of high holding pressure(300 k Pa)enhances the feeding ability of the alloy,leading to an increase of the density.Meanwhile,the cooling rate of the alloy is increased by 100%.In addition,the tensile testing results show that the increase of holding pressure from 50 to 300 k Pa improves the tensile strength and elongation of the alloy by 6.2%and 81.3%,respectively.However,excessive holding pressure(400 k Pa)might lower the density and cooling rate of the alloy due to the feeding channels being blocked.