Experimental and numerical study on ignition and combustion characteristics of boron-magnesium composite powders

A high-pressure laser ignition and combustion system with adjustable oxidizer gas atmosphere is established to investigate the ignition and combustion characteristics of boron-magnesium(BM)com-posite powders.An ignition and combustion model of BM powders is established and validated in the present study.The results show that increasing water content,O_(2) content and Mg content all result in shorter ignition delay time of BM powders,among which the effect of water content is the most obvious.However,ignition delay time increases as pressure increases.The combustion time decreases with increasing Mg content and ambient pressure but increases with water content.With the increase of O_(2) content,combustion time of BM powders first increases and then decreases,which means a critical O_(2) content exists above which combustion time decreases.The results show that there exists a trade-off between ignition and combustion performance of BM composite powders.

Fabrication and characterization of multi-scale coated boron powders with improved combustion performance:A brief review

Boron has high mass and volume calorific values,but it is difficult to ignite and has low combustion efficiency.This literature review summarizes the strategies that are used to solve the above-mentioned problems,which include coatings of boron by using fluoride compounds,energetic composites,metal fuels,and metal oxides.Coating techniques include recrystallization,dual-solvent,phase transfer,electrospinning,etc.As one of the effective coating agents,the fluorine compounds can react with the oxide shell of boron powder.In comparison,the energetic composites can effectively improve the flame temperature of boron powder and enhance the evaporation efficiency of oxide film as a condensed product.Metals and metal oxides would react with boron powder to form metal borides with a lower ignition point,which could reduce its ignition temperature.

Micro-aluminum powder with bi-or tri-component alloy coating as a promising catalyst:Boosting pyrolysis and combustion of ammonium perchlorate

A novel design of micro-aluminum(μAl)powder coated with bi-/tri-component alloy layer,such as:Ni-P and Ni-P-Cu(namely,Al@Ni-P,Al@Ni-P-Cu,respectively),as combustion catalysts,were introduced to release its huge energy inside Al-core and promote rapid pyrolysis of ammonium perchlorate(AP)at a lower temperature in aluminized propellants.The microstructure of Al@Ni-P-Cu demonstrates that a three-layer Ni-P-Cu shell,with the thickness of~100 nm,is uniformly supported byμAl carrier(fuel unit),which has an amorphous surface with a thickness of~2.3 nm(catalytic unit).The peak temperature of AP with the addition of Al@Ni-P-Cu(3.5%)could significantly drop to 316.2℃ at high-temperature thermal decomposition,reduced by 124.3℃,in comparison to that of pure AP with 440.5℃.It illustrated that the introduction of Al@Ni-P-Cu could weaken or even eliminate the obstacle of AP pyrolysis due to its reduction of activation energy with 118.28 kJ/mol.The laser ignition results showed that the ignition delay time of Al@Ni-P-Cu/AP mixture with 78 ms in air is shorter than that of Al@Ni-P/AP(118 ms),decreased by 33.90%.Those astonishing breakthroughs were attributed to the synergistic effects of adequate active sites on amorphous surface and oxidation exothermic reactions(7597.7 J/g)of Al@Ni-P-Cu,resulting in accelerated mass and/or heat transfer rate to catalyze AP pyrolysis and combustion.Moreover,it is believed to provide an alternative Al-based combustion catalyst for propellant designer,to promote the development the propellants toward a higher energy.

Effect of particle size and oxygen content on ignition and combustion of aluminum particles

Particle size and oxygen content are two of the key factors that affect the ignition and combustion properties of aluminum particles. In this study, a laser ignition experimental system and flame test system were built to analyze the ignition and combustion characteristics and the flame morphology of aluminum particles. A thermobalance system was used to analyze the thermal oxidation characteristics. In addition, the microstructure of aluminum was analyzed by scanning electron microscopy. It was found that the oxidized products were some of the gas phase products agglomerated. Smaller particle size samples showed better combustion characteristics. The combustion intensity, self-sustaining combustion time and the burn-off rate showed a rising trend with the decrease in the particle size. Increasing the oxygen content in the atmosphere could improve the ignition and combustion characteristics of the samples. Four distinct stages were observed in the process of ignition and combustion. Small particle size samples had a larger flame height and luminance, and the self-sustaining combustion time was much longer.Three distinct stages were observed during the thermal oxidation process. The degree of oxidation for small-sized samples was significantly higher than that for the larger particle size samples.Moreover, it was observed that the higher the oxygen content, the higher the degree of oxidation was.

Experimental investigations of mechanical and reaction responses for drop-weight impacted energetic particles

Low-velocity drop-weight impact experiments on individual and multiple Cyclotetramethylene tetranitramine (HMX) energetic particles were performed using a modified drop-weight machine equipped with high-speed photography components. Multiple particles experienced more severe burning reactions than an individual particle. Comparisons between impacted salt and HMX particle show that jetting in HMX is mainly due to the motion of fragmented particles driven by gaseous reaction products. Velocity of jetting, flame propagation, and area expansion were measured via image processing, making it possible to quantify the chemical reaction or mechanical deformation violence at different stages.

A Steam-Plasma Igniter for Aluminum Powder Combustion

High-temperature ignition is essential for the ignition and combustion of energetic metal fuels, including aluminum and magnesium particles which are protected by their high- melting-temperature oxides. A plasma torch characterized by an ultrahigh-temperature plasma plume fulfills such high-temperature ignition conditions. A new steam plasma igniter is designed and successfully validated by aluminum power ignition and combustion tests. The steam plasma rapidly stabilizes in both plasma and steam jet modes. Parametric investigation of the steam plasma jet is conducted in terms of arc strength. A high-speed camera and an oscilloscope method visualize the discharge characteristics, and optical emission spectroscopy measures the thermochemical properties of the plasma jet. The diatomic molecule OH fitting method, the Boltzmann plot method, and short exposure capturing with an intensified charge coupled device record the axial distributions of the rotational gas temperature, excitation temperature, and OH radical distribution, respectively. The excitation temperature at the nozzle tip is near 5500 K, and the gas temperature is 5400 K.

Preparation and characterization of high-reactivity explosive-based nano-boron microspheres

Boron nanoparticles,with their remarkably high gravimetric and volumetric calorific values,emerge as the most promising fuel in energetic fields.However,challenges such as susceptibility to oxidation,high ignition temperature,and low combustion efficiency have constrained their further applications.In this study,we fabricated high explosives based nano-boron microspheres with uniform size using the electrostatic spray method,in which the boron nanoparticles and high explosives(CL-20 or PETN)are closely bonded together by fluorinated polymer(F2602)and evenly distributed.The results indicated that the microspheres exhibited high sphericity and showed an enhanced antioxidant capability.The addition of high-energy explosives not only reduced the thermal oxidation temperature of nano-boron powder within the microspheres but also significantly enhanced the pressurization rate.Additionally,the microspheres with added high-energy explosives released more energy during the combustion process.Compared to physically mixed samples,electrostatically sprayed microspheres with a uniform microstructure still exhibited higher reactivity.Therefore,the design and synthesis of microspheres with controllable structures using the electrostatic spray method show promising application prospects.