Experimental study of solid-liquid origami composite structures with improved impact resistance

In this paper,a liquid-solid origami composite design is proposed for the improvement of impact resistance.Employing this design strategy,Kresling origami composite structures with different fillings were designed and fabricated,namely air,water,and shear thickening fluid(STF).Quasi-static compression and drop-weight impact experiments were carried out to compare and reveal the static and dynamic mechanical behavior of these structures.The results from drop-weight impact experiments demonstrated that the solid-liquid Kresling origami composite structures exhibited superior yield strength and reduced peak force when compared to their empty counterparts.Notably,the Kresling origami structures filled with STF exhibited significantly heightened yield strength and reduced peak force.For example,at an impact velocity of 3 m/s,the yield strength of single-layer STF-filled Kresling origami structures increased by 772.7%and the peak force decreased by 68.6%.This liquid-solid origami composite design holds the potential to advance the application of origami structures in critical areas such as aerospace,intelligent protection and other important fields.The demonstrated improvements in impact resistance underscore the practical viability of this approach in enhancing structural performance for a range of applications.

Combined effect of steel fibres and steel rebars on impact resistance of high performance concrete

The impact properties of normal concrete (NC) and reinforced concrete (RC) specimens,steel fibre reinforced concrete (SFRC) specimens and RC+SFRC specimens with different steel fibre dosages were investigated with the drop-weight impact test recommended by ACI Committee 544.The results indicate that the number of blows to final failure is greatly increased by addition of steel fibres.Moreover,the combination of steel fibres and steel rebars demonstrates a significant positive composite effect on the impact resistance,which results in the improvement in impact toughness of concrete specimens.In the view of variation of impact test results,the two-parameter Weibull distribution was adopted to analyze the experimental data.It is proved that the probabilistic distributions of the blows to first crack and to final failure of six types of samples approximately follow two-parameter Weibull distribution.

Effect of T6I6 treatment on dynamic mechanical behaviour of Al-Si-Mg-Cu cast alloy and impact resistance of its cast motor shell

The effect of T6I6 treatment on the dynamic mechanical and microstructure behaviour of Al-Si-Mg-Cu cast alloy was investigated using split Hopkinson pressure bar(SHPB), transmission electron microscopy(TEM), and highresolution transmission electron microscopy(HRTEM). Besides, the impact resistances of T6I6 and T6 motor shells of new energy vehicles made of Al-Si-Mg-Cu cast alloy were compared using a trolley crash test. The results indicated that the main strengthening-phases of the T6 peak-aged and T6I6 peak-aged alloy were GP zone and β″ precipitates. T6I6treatment can increase the density and size of β″ precipitates in peak-aged alloy and enhance both its tensile strength(σb)and elongation(δ). The dynamic toughness values of T6I6 samples are 50.34 MJ/m^(3) at 2000 s^(-1) and 177.34 MJ/m^(3) at 5000 s^(-1) which are 20% and 12% higher than those of T6 samples, respectively. Compared with a T6 shell, the overall deformation of T6I6 shell is more uniform during the crash test. At an impact momentum of 3.5×10;kg·m/s, the T6I6shell breaks down at 0.38 s which is 0.10 s later than the T6 shell.

Impact Resistance of a Novel Expanded Polystyrene Cement-based Material

The mechanical property of a novel expanded polystyrene cement-based material （EPS-C）, which was prepared by compressing semi-dry materials molding, was investigated. The compressive behavior was analyzed by compression tests to gain the energy absorbed during failure. Performance for impact resistance was tested by a self-made device. The results figures out that the EPS-C has good toughness and can reach swain of 0.7 without failure. The stress-strain curve is quite different from that of normal EPS concrete. It can be divided into three stages and in the third stage the compressing exhibits the highest energy absorption. With the rising of cement ratio, the impact force absorption （IEA） decreases first and then increases. The impact energy absorption （IEA） increases first and then decreases. The lowest IEA and the highest lEA appear at the cement dosage from 233 g/L to 267 g/L and from 233 g/L to 300 g/L, respectively.

Hygrothermal effect on high-velocity impact resistance of woven composites

The woven glass fiber reinforced composites(GFRP)subjected to high-speed impact is investigated to identify the hygrothermal aging effect on the impact resistance.Both the hygrothermal aged and unaged glass/epoxy laminates are subjected to different impact velocities,which is confirmed as a sensitive factor for the failure modes and mechanisms.The results show the hygrothermal aging effect decreases the ballistic limit by 14.9%,but the influence on ballistic performance is limited within the impact velocity closed to the ballistic limit.The failure modes and energy dissipation mechanisms are confirmed to be slightly influenced by the hygrothermal aging effect.The hygrothermal aging effect induced localization of structural deformation and degradation of mechanical properties are the main reasons for the composite undergoing the same failure modes at smaller impact velocities.Based on the energy absorption mechanisms,analytical expressions predict the ballistic limit and energy absorption to reasonable accuracy,the underestimated total energy absorption results in a relatively poor agreement between the measured and predicted energy absorption efficiency.

Effect of Rare Earth Elements on the Impact Wear Resistance of Nitrocarburizing Layers

In this paper the effect of rare earth elements on the toughness and impact wear resistance of nitrocarburiz- ing layers is studied.The experimental results show that the toughness and impact wear resistance of RE-nitrocarburizing layers are increased significantly compared with that of conventional nitrocarburizing lay- ers.The service life of hot die for manufacturing bicycle bolts increased more than 100%.The impact wear mechanism of RE-nitrocarburizing layers is investigated by SEM as well.

Low-Energy Multi-Impact Fracture Resistance of Cross Rolled Low Chromium Cast Semi-Steel Containing Rare Earth Grinding Ball

The low-energy multi-impact fracture resistance of the cross rolled low chromium cast semi-steel containing RE grinding balls was studied. Moreover, its damage mode was analyzed by means of metallographic examination, scanning electron microscopic examination and drop ball test. The results show that it can obtain extractive impact fracture resistance after proper heat treatment. More advantages were obtained for the ball worked in the condition of low-imp ductility act. The main reasons are the function of RE and the change in morphology of eutectic carbide network.

Research on the Dynamic Compressibility of Polyurethane Microcellular Elastomer and its Application for Impact Resistance

The packaging materials with cushioning performance are used to prevent the internal contents from being damaged by the impact and vibration of external forces.The polyurethane microcellular elastomers(PUMEs)can absorb energy through cell collapse and molecular chain creep.In this study,PUMEs with different densities were investigated by scanning electron microscopy,dynamic mechanical analysis and dynamic compression tests.PUMEs exhibited significant im pact resistance and the maximum peak stress attenuation ratio reached 73.33%.The protective equipment was made by PUME with the optimal density of 600 kg/m^(3),and then the acceleration sensing device installed with the same protective equipment fell from a height of 3,5 and 10 m to evaluate the energy-absorbing property and reusability of PUMEs.The results showed that PUMEs equipment reduced the peak acceleration of the device by 93.84%,with a maximum deviation of 9%between actual test and simulation,and shortened the impact time of first landing by 57.39%.In addition,the equipment PUMEs equipment could effectively reduce the stress on the protected items.

Structural Design Study of Air-Dropped Unmanned Maritime Mobile Search and Rescue Platforms

In order to improve the efficiency and safety of search and rescue(SAR)at sea,this paper proposes a kind of emergency rapid rescue unmanned craft(air-dropped unmanned maritime motorized search and rescue platform)that can be delivered by a large transport aircraft.This paper studies the structural design scheme of the platform,and the main scale of the platform,the choice of power system and the impact resistance performance are considered in the design process to ensure its rapid response and effective rescue capability under complex sea conditions.Simulation results show that the platform can withstand the impact of air injection into the water and the shipboard equipment can operate normally under the impact load,thus verifying the feasibility and safety of the design.This study serves to improve the maritime search and rescue system and enhance the oceanic emergency response capability.

Effect of Cycling Low Velocity Impact on Mechanical and Wear Properties of CFRP Laminate Composites

The mechanical and wear properties of CFRP laminate were investigated using a method of cycling low velocity impact, to study the trend and mechanism of impact resistance of the CFRP laminate under repeated impact during its service process. The interface responses of CFRP laminate under di erent impact kinetic energy during the cycling impact process were studied were studied experimentally, such as impact contact duration, deformation and energy absorption. The worn surface morphologies were observed through optical microscopy and a 3?D surface profiler and the cross?sectional morphologies were observed through SEM to investigate the mechanism of impact material dam?age. Based on a single?degree?of?freedom damping vibration model, the normal contact sti ness and contact damp?ing of the material in di erent wear stages were calculated. It shows the failure process of CFRP laminate damaged by accumulated absorption energy under the cycling impact of di erent initial kinetic energy. The results indicate that the sti ness and damping coe cients will change at di erent impact velocities or cycle numbers. The damage mechanism of CFRP laminates under cycling low kinetic energy is delamination. After repeated experiments, it was found that there was a threshold value for the accumulated absorption energy before the failure of the CFRP laminate.

The Failure Mechanism of CFRP Reinforced RC Beam under Impact Loads

The influence of carbon fiber reinforced plastic(CFRP)on dynamic mechanical properties of reinforced concrete(RC)beam was studied by drop hammer impact test system.The impact behaviors of beam,including failure mode,impact force peak value and peak deflection were analyzed.The experimental results show that bonding CFRP can reduce the crack width and change the failure mode of the beam.The length of CFRP has a certain influence on the impact force and deflection,and the peak inertia force of most beams is roughly in the range of 1/2-5/6 of the peak impact force.In addition,dynamic increase factor(DIF)increases with the increase of CFRP length,and its maximum value can reach 2.11.

STATIC AND FATIGUE BEHAVIOR OF IMPACTED AS4/PEEK THERMOPLASTIC COMPOSITES UNDER COMPRESSION LOAD

Static and fatigue tests under compression load were made on impacted AS4/PEEK and T300/913C graphite/epoxy with [45/90/-45/0]5S stacking sequence. The comparison of the damage tolerance assessment for thermosetting and thermoplastic composites shows that thermoplastics are more damage tolerant under compression. Impacted thermoplastic composites have excellent compression-compression fatigue behavior. The damage growth life is only a few percent of their total fatigue life and no regular damage growth can be found. Some design principles for thermosetting composite structures may still be used.

Study of Impact Resistance Based on Porcupine Quills Bionic Thin-walled Structure

Using an electron microscope to observe the microstructure of a porcupine quills cross-section and a bionic method,a new bionic structure was proposed.The performance of the structure in terms of energy absorption,maximum impact force withstood,and impact force efficiency was evaluated using Ansys finite element simulation software to simulate the structure's impact.To examine the impact of ribs on the structural performance of the bionic porcupine quills,a control structure was developed.According to the results of the finite element simulation,the presence of ribs in the Bionic porcupine quills structure can transfer stress uniformly to the overall structure and share stress for some of the rupture-prone regions.Ribs reduce stress concentration in specific areas and increase the impact force efficiency of the structure.The SEA and IFE values of bionic porcupine quills were 30.01 kJ/kg and 84.22%,respectively.The structure is then optimized for parameter design in order to find the optimal structure by response surface in order to improve the structure's SEA and decrease its MIF.In order to evaluate the precision of the response surface,the optimal structure predicted is validated using finite element simulation.

Numerical Simulation of the Influence of Water Flow on the Piers of a Bridge for Different Incidence Angles

A two-dimensional mathematical model is used to simulate the influence of water flow on the piers of a bridge for different incidence angles.In particular,a finite volume method is used to discretize the Navier-Stokes control equations and calculate the circumferential pressure coefficient distribution on the bridge piers’surface.The results show that the deflection of the flow is non-monotonic.It first increases and then decreases with an increase in the skew angle.

Morphological and Spatial Effects on Toughness and Impact Damage Resistance of PAEK-toughened BMI and Graphite Fiber Composite Laminates

The microstructure property relationships have been studied in terms of glass transition behavior,phase morphology,and fracture toughness on thermoplastic polyetherketone with a phenolphthalein side group (PAEK) toughened bismaleimdes (BMI) resins,and in terms of interlaminar morphology and compression after impact (CAI) on the graphite fiber (T700SC),the rein-forced BMI matrix composites that are toughened with a so-called ex-situ concept,respectively. The characteristic morphology spectrum has been found ...

Properties of Cross-Rolled Low Alloy White Cast Iron Grinding Ball

The low-energy, multi-impact fracture resistance and the abrasiveness of the cross-rolled low alloy white cast iron grinding balls were studied after heat treatments at residual rolling temperature. Moreover, the means by which they are damaged and characters of the wear surface were analyzed. The results show that high resistance to impact fracture and high abrasiveness can be achieved after appropriate heat treatment at residual rolling temperature. This kind of heat treatment technology has several advantages under low impact and hard abrasive. These results are very useful for determining the optimized heat treatment technology at residual rolling temperatures.

Improvement of impact resistance of plain-woven composite by embedding superelastic shape memory alloy wires

Carbon fiber reinforced polymer (CFRP) composites have excellent mechanical properties, specifically, high specific stiffness and strength. However, most CFRP composites exhibit poor impact resistance. To overcome this limitation, this study presents a new plain-woven CFRP composite embedded with superelastic shape memory alloy (SMA) wires. Composite specimens are fabricated using the vacuum-assisted resin injection method. Drop-weight impact tests are conducted on composite specimens with and without SMA wires to evaluate the improvement of impact resistance. The material models of the CFRP composite and superelastic SMA wire are introduced and implemented into a finite element (FE) software by the explicit user-defined material subroutine. FE simulations of the drop-weight impact tests are performed to reveal the superelastic deformation and debonding failure of the SMA inserts. Improvement of the energy absorption capacity and toughness of the SMA-CFRP composite is confirmed by the comparison results.

High Impact Resistance Epoxy Resins by Incorporation of Quadruply Hydrogen Bonded Supramolecular Polymers

A bisphenol A based epoxy was incorporated with a quadruply hydrogen bonded supramolecular polymer as a toughening agent to prepare a composite epoxy resin with higher impact resistance. The supramolecular polymer comprising poly-（propylene glycol） bis（2-aminopropyl） ether chains and 2-ureido-4[1H]-pyrimidinone moieties（UPy） self-assembled into spherical domains with sizes of 300 nm to 600 nm in diameter by micro phase separation in bulk epoxy matrixes. A significant improvement of 300% in impact resistance of the supramolecular polymer incorporated epoxy resin was obtained when the content of supramolecular polymer was 10 wt%. Tensile tests showed that the mechanical properties of the modified epoxy resin containing the hydrogen-bonded supramolecular polymers are also improved compared with those of the neat epoxy resin.

Influences of POSS-E-GO Content on Mechanical Properties of Bio-based Epoxy/DOPO-POSS Nanocomposites

The bio-based epoxy nanocomposite(GAER/DOPO-POSS)was prepared from gallic epoxy resin(GAER)and polyhedral oligomeric silsesquioxane(which containing 9,10-dihydrogen-9-oxo-10-phosphorus-phenanthrene-10-oxide groups,called DOPO-POSS).The polyhedral oligomeric silsesquioxane containing epoxy groups(E-POSS)was grafted onto aminated graphene oxide(E-GO),then the novel POSS-E-GO was obtained.The POSS-E-GO was used as modifier for GAER/DOPO-POSS nanocomposite.The influences of POSS-E-GO content on mechanical properties,dynamic mechanical properties and thermal stability of GAER/DOPO-POSS nanocomposites were determined.The experimental results show that POSS-E-GO can significantly improve the toughness of the GAER/DOPO-POSS nanocomposite.When 0.5wt% POSS-E-GO was added in GAER/DOPO-POSS nanocomposite,the impact strength of the nanocomposite was 4.74 kJ/m^(2) higher than that in the absence of POSS-E-GO,meantime the initial thermal degradation temperature was 277℃.

Effect of Rubber Particle Modifi cation on Properties of Rubberized Concrete

To improve the combination of cement matrix and waste tire rubber particles in concrete, the rubber particles were treated with acrylic acid（ACA） and polyethylene glycol（PEG） for grafting hydrophilic groups on their surfaces. The X-Ray photoelectron spectroscopy（XPS） and surface contact angle were used to characterize the hydrophilicity and surface functional group of rubber particles. The effect of rubber particle modifi cation on fresh/hardened properties of rubberized concrete was studied. The experimental results show that the contact angle between rubber particle surface and water decreases when rubber particle is modifi ed. Compared with the unmodifi ed rubberized concrete（RC）, the unit weight of modifi ed rubberized concrete（MRC） changes slightly. However, the slump, air-entrainment, compressive strength, flexural strength, and impact performance of MRC are obviously improved. Under good condition of slump, the water-cement ratio of the MRC can be reduced from 0.4 to 0.38. And the compressive strength and fl exural strength of the MRC（10% rubber particle content） can be increased by 25.9% and 26.4%, respectively.