Characteristic Surface Oxide Film Cracking Behavior of a Fe-Ni-Cr Alloy under In-phase and Out-of-phase Thermo-mechanical Fatigue

The surface oxide film cracking behavior of Fe-30Ni-20Cr alloy under in-phase and out-of-phase synchronizing thermal cycling with mechanical cycling was studied.Surface oxide film cracking along the grain boundary under in-phase overlapping was creep predominant fracture mechanisms.Strongly induced slip lines preceding were accompanied by the surface oxide film cracking under Out-of phase,and the shear cracking was dominant mode.Negative mean stress could counteract a part of the tensile component of alternative stress,so as to delay the cracking process under in-phase,but positive mean stress overlapping the tensile alternative stress could accelerate the cycling cracking process under out-of-phase.

Design of Seven-core Photonic Crystal Fiber with Flat In-phase Mode for Yb: Fiber Laser Pumping

We numerically investigate the seven-core photonic crystal fiber (PCF) with the zero dispersion wavelength designed in the range of 1000 - 1080 nm, particularly suitable for the ytterbium-doped fiber laser pumping. Also, the PCFs are well designed for obtaining a flat in-phase mode by carefully adjusting the diameter of inner layer six holes, and the corresponding empirical values of fiber structure are summarized and listed. The variations of inner six holes to the amplitude of in-phase mode are further investigated, and our results show that a better tolerance can be achieved in the fiber structures with lower filling ratio configuration.

On the Sub-Critical Bifurcation of Anti-Phase and In-Phase Synchronized Vortex Shedding Forms

Transition of flows past a pair of side-by-side circular cylinders are investigated by numerical simulations and the bifurcation analysis of the numerical results. Various flow patterns behind the cylinder-pair have been identified by the gap ratio (G) and Reynolds number (Re). This study focus on transition of in-phase and anti-phase vortex shedding synchronized forms. A nested Cartesian-grid formulation, in combination with an effective immersed boundary method and a two-step fractional-step procedure, has been adopted to simulate the flows. Numerical results reveal that the in-phase and anti-phase vortex shedding flows at Re = 100 can co-exist at 2.08 ≤G≤ 2.58. Hysteresis loop with increasing/decreasing G at constant Reynolds number Re = 100 is reported.

Single-trial EEG classification using in-phase average for brain-computer interface

Communication signals should be estimated by a single trial in a brain-computer interface.Since the relativity of visual evoked potentials from different sites should be stronger than those of the spontaneous electro-encephalogram(EEG),this paper adopted the time-lock averaged signals from multi-channels as features.200 trials of EEG recordings evoked by target or non-target stimuli were classified by the support vector machine(SVM).Results show that a classification accuracy of higher than 97%can be obtained by merely using the 250–550 ms time section of the averaged signals with channel Cz and Pz as features.It suggests that a possible approach to boost communication speed and simplify the designation of the brain-computer interface(BCI)system is worthy of an attempt in this way.

Conversion of out-of-phase to in-phase order in coupled laser arrays with second harmonics

A novel method for converting an array of out-of-phase lasers into one of in-phase lasers that can be tightly focused is presented.The method exploits second-harmonic generation and can be adapted for different laser arrays geometries.Experimental and calculated results,presented for negatively coupled lasers formed in a square,honeycomb,and triangular geometries are in good agreement.

Bafang Fabric Keep up the World Demin in-phase

From Shanghai to Haining Bafang Weaving Co., Ltd., through China’s busiest high way, we saw the adverts of Bafang Fabric on the side of the road. Upon the arriving in the downtown of Haining, the huge advert of Bafang Fabric attracts your eye --"advertising plus advertising to increase strength, that is, quality, and brand ".

Gain-Enhanced Metamaterial Based Antenna for 5G Communication Standards

Metamaterial surfaces play a vital role to achieve the surface waves suppression and in-phase reflection,in order to improve the antenna performance.In this paper,the performance comparison of a fifth generation(5G)antenna design is analyzed and compared with a metamaterial-based antenna for 5G communication system applications.Metamaterial surface is utilized as a reflector due to its in-phase reflection characteristic and high-impedance nature to improve the gain of an antenna.As conventional conducting ground plane does not give enough surface waves suppression which affects the antenna performance in terms of efficiency and gain etc.These factors are well considered in this work and improved by using the metamaterial surface.The radiating element of the proposed metamaterial based antenna is made up of copper material which is backed by the substrate,i.e.,Rogers-4003 with a standard thickness,loss tangent and a relative permittivity of 1.524 mm,0.0027 and 3.55,correspondingly.The proposed antenna with and without metamaterial surface operates at the central frequency of 3.32 GHz and 3.60 GHz,correspondingly.The traditional antenna yields a boresight gain of 2.76 dB which is further improved to 6.26 dB,using the metamaterial surface.The radiation efficiency of the proposed metamaterial-based 5G antenna is above 85%at the desired central frequency.

High-performance compensation scheme for frequency-dependent IQ imbalances in OFDM transmitter and receiver

An efficient compensation scheme combining a timedomain Gaussian elimination（GE） channel estimator and a frequency-domain GE equalizer is proposed for orthogonal frequency division multiplexing（OFDM） systems with frequencydependent in-phase and quadrature-phase（IQ） imbalances at both transmitter and receiver.Compared with the traditional least square and least mean square compensation schemes,the proposed compensation scheme achieves the same bit error rate as the ideal IQ branches by using only two training OFDM symbols instead of about 20 OFDM symbols.

A new model for life prediction of GH4133 under TMF conditions

Thermal mechanical cyclic strain tests were carried out under in-phase andout-of-phase conditions on a Nickel-base Superalloy GH4133 in the temperature range of 571-823 degC. Based on analyzing the present models of TMF (thermal mechanical fatigue) life prediction, a newmodel for predicting nickel-base superalloy TMF lifetime was proposed. TMF life of superalloy GH4133was calculated accurately based on the new model. Experimental TMF life has been compared with thecalculated results and all results fall in the scatter band of 1.5. The calculating results showthat the new model is not only simple, but also precise. This model will play great roles as lifeprediction of the metal materials and the engineering components subjected to non-isothermal serviceconditions.

Decoupled estimation of frequency-dependent IQI and channel for OFDM systems with direct-conversion transceivers

The in-phase and quadrature-phase imbalance (IQI) is one of the major radio frequency impairments existing in orthogonal frequency division multiplexing (OFDM) systems with direct-conversion transceivers. During the transmission of the communication signal, the impact of IQI is coupled with channel impulse responses (CIR), which makes the traditional channel estimation schemes ineffective. A decoupled estimation scheme is proposed to separately estimate the frequency-dependent IQI and wireless channel. Firstly, the generalized channel model is built to separate the parameters of IQI and wireless channel. Then an iterative estimation scheme of frequency-dependent IQI is designed at the initial stage of communication. Finally, based on the estimation result of IQI, the least square algorithm is utilized to estimate the channel-related parameters at each time of channel variation. Compared with the joint estimation schemes of IQI and channel, the proposed decoupled estimation scheme requires much lower training overhead at each time of channel variation. Simulation results demonstrate the good estimation performance of the proposed scheme.

Optimization of Mapping Rule of Bit-Interleaved Turbo Coded Modulation with 16QAM

Optimization of mapping rule of bit-interleaved Turbo coded modulation with 16 quadrature amplitude modulation (QAM) is investigated based on different impacts of various encoded bits sequence on Turbo decoding performance. Furthermore, bit-interleaved in-phase and quadrature phase (I-Q) Turbo coded modulation scheme are designed similarly with I-Q trellis coded modulation (TCM). Through performance evaluation and analysis, it can be seen that the novel mapping rule outperforms traditional one and the I-Q Turbo coded modulation can not achieve good performance as expected. Therefore, there is not obvious advantage in using I-Q method in bit-interleaved Turbo coded modulation.

EFFECTS OF STRAIN RATIO ON THERMAL-MECHANICAL CYCLIC STRESS-STRAIN RESPONSE AND FATIGUE LIFE IN DS SUPERALLOY DZ125

The effects of strain ratio on thermal-mechanical cyclic stress-strain response and fatigue life in DS superalloy DZ125 have been studied by performing tests at various strain ratio experiments, under strain-controlled and temperature cycling from 550 to 1000℃. It is shown that thermal-mechanical cyclic stress-strain response behavior not only depend on magnitude of strain, and temperature-loading phase angle, but also strain ratio. Fatigue life at strain ratio Rε=-0.3 is longer than that of strain ratio Rε=-1.0, under in-phase thermal-mechanical loading. However, Fatigue life at strain ratio Rε=-0.3 is shorter than that of strain ratio Rε=-1.0, under out-of-phase thermal-mechanical loading. The thermal-mechanical fatigue (TMF) damage model was discussed. Results of fractography show that fatigue, creep and oxidation damage always occur during TMF. The main damage mode depends on loading wave, strain ratio and magnitude of strain.

Hepatic steatosis with mass effect:A case report

BACKGROUND Hepatic steatosis is a common radiologic finding.Some imaging inklings are the absence of a mass effect,and there is currently no report of hepatic steatosis with mass effect.CASE SUMMARY A 23-year-old female was admitted due to a liver mass for half a month.No obvious abnormalities were found in physical and laboratory examinations.Ultrasound,computed tomography,and magnetic resonance imaging showed a huge mass between the liver and stomach with a significant mass effect,and the caudate lobe and left lobe of the liver were involved.The signal on T2-and T1-weighted fat-saturated images of the mass was significantly reduced,and the enhanced scan showed inhomogeneous enhancement.Surgical and pathological findings indicated the diagnosis of hepatic steatosis.The operation and re-review of the patient’s images showed that the lesion was supplied by the branch of the hepatic artery.The signal on T1-weighted out-of-phase images of the lesion was lower than on in-phase images,and there was no black rim cancellation artifact around the hepatic steatosis area on T1-weighted out-of-phase images.The dynamic enhancement pattern of the lesion was similar to that of the adjacent normal liver parenchyma.The above characteristics suggested that the lesion was hepatic steatosis.However,in this case,the lesion showed exogenous growth and was mass-like,with an obvious mass effect,which has not been reported previously.CONCLUSION Hepatic steatosis could grow exogenously and has an obvious mass effect.It needs to be distinguished from fat-rich tumors.The T1-weighted in-and out-of-phase images and dynamic enhanced scanning are valuable for differential diagnosis of this lesion.