We numerically investigate the seven-core photonic crystal fiber (PCF) with the zero dispersion wavelength designed in the range of 1000 - 1080 nm, particularly suitable for the ytterbium-doped fiber laser pumping. Al...We numerically investigate the seven-core photonic crystal fiber (PCF) with the zero dispersion wavelength designed in the range of 1000 - 1080 nm, particularly suitable for the ytterbium-doped fiber laser pumping. Also, the PCFs are well designed for obtaining a flat in-phase mode by carefully adjusting the diameter of inner layer six holes, and the corresponding empirical values of fiber structure are summarized and listed. The variations of inner six holes to the amplitude of in-phase mode are further investigated, and our results show that a better tolerance can be achieved in the fiber structures with lower filling ratio configuration.展开更多
Transition of flows past a pair of side-by-side circular cylinders are investigated by numerical simulations and the bifurcation analysis of the numerical results. Various flow patterns behind the cylinder-pair have b...Transition of flows past a pair of side-by-side circular cylinders are investigated by numerical simulations and the bifurcation analysis of the numerical results. Various flow patterns behind the cylinder-pair have been identified by the gap ratio (G) and Reynolds number (Re). This study focus on transition of in-phase and anti-phase vortex shedding synchronized forms. A nested Cartesian-grid formulation, in combination with an effective immersed boundary method and a two-step fractional-step procedure, has been adopted to simulate the flows. Numerical results reveal that the in-phase and anti-phase vortex shedding flows at Re = 100 can co-exist at 2.08 ≤G≤ 2.58. Hysteresis loop with increasing/decreasing G at constant Reynolds number Re = 100 is reported.展开更多
The surface oxide film cracking behavior of Fe-30Ni-20Cr alloy under in-phase and out-of-phase synchronizing thermal cycling with mechanical cycling was studied.Surface oxide film cracking along the grain boundary und...The surface oxide film cracking behavior of Fe-30Ni-20Cr alloy under in-phase and out-of-phase synchronizing thermal cycling with mechanical cycling was studied.Surface oxide film cracking along the grain boundary under in-phase overlapping was creep predominant fracture mechanisms.Strongly induced slip lines preceding were accompanied by the surface oxide film cracking under Out-of phase,and the shear cracking was dominant mode.Negative mean stress could counteract a part of the tensile component of alternative stress,so as to delay the cracking process under in-phase,but positive mean stress overlapping the tensile alternative stress could accelerate the cycling cracking process under out-of-phase.展开更多
Communication signals should be estimated by a single trial in a brain-computer interface.Since the relativity of visual evoked potentials from different sites should be stronger than those of the spontaneous electro-...Communication signals should be estimated by a single trial in a brain-computer interface.Since the relativity of visual evoked potentials from different sites should be stronger than those of the spontaneous electro-encephalogram(EEG),this paper adopted the time-lock averaged signals from multi-channels as features.200 trials of EEG recordings evoked by target or non-target stimuli were classified by the support vector machine(SVM).Results show that a classification accuracy of higher than 97%can be obtained by merely using the 250–550 ms time section of the averaged signals with channel Cz and Pz as features.It suggests that a possible approach to boost communication speed and simplify the designation of the brain-computer interface(BCI)system is worthy of an attempt in this way.展开更多
A novel method for converting an array of out-of-phase lasers into one of in-phase lasers that can be tightly focused is presented.The method exploits second-harmonic generation and can be adapted for different laser ...A novel method for converting an array of out-of-phase lasers into one of in-phase lasers that can be tightly focused is presented.The method exploits second-harmonic generation and can be adapted for different laser arrays geometries.Experimental and calculated results,presented for negatively coupled lasers formed in a square,honeycomb,and triangular geometries are in good agreement.展开更多
From Shanghai to Haining Bafang Weaving Co., Ltd., through China’s busiest high way, we saw the adverts of Bafang Fabric on the side of the road. Upon the arriving in the downtown of Haining, the huge advert of Bafan...From Shanghai to Haining Bafang Weaving Co., Ltd., through China’s busiest high way, we saw the adverts of Bafang Fabric on the side of the road. Upon the arriving in the downtown of Haining, the huge advert of Bafang Fabric attracts your eye --"advertising plus advertising to increase strength, that is, quality, and brand ".展开更多
Metamaterial surfaces play a vital role to achieve the surface waves suppression and in-phase reflection,in order to improve the antenna performance.In this paper,the performance comparison of a fifth generation(5G)an...Metamaterial surfaces play a vital role to achieve the surface waves suppression and in-phase reflection,in order to improve the antenna performance.In this paper,the performance comparison of a fifth generation(5G)antenna design is analyzed and compared with a metamaterial-based antenna for 5G communication system applications.Metamaterial surface is utilized as a reflector due to its in-phase reflection characteristic and high-impedance nature to improve the gain of an antenna.As conventional conducting ground plane does not give enough surface waves suppression which affects the antenna performance in terms of efficiency and gain etc.These factors are well considered in this work and improved by using the metamaterial surface.The radiating element of the proposed metamaterial based antenna is made up of copper material which is backed by the substrate,i.e.,Rogers-4003 with a standard thickness,loss tangent and a relative permittivity of 1.524 mm,0.0027 and 3.55,correspondingly.The proposed antenna with and without metamaterial surface operates at the central frequency of 3.32 GHz and 3.60 GHz,correspondingly.The traditional antenna yields a boresight gain of 2.76 dB which is further improved to 6.26 dB,using the metamaterial surface.The radiation efficiency of the proposed metamaterial-based 5G antenna is above 85%at the desired central frequency.展开更多
An efficient compensation scheme combining a timedomain Gaussian elimination(GE) channel estimator and a frequency-domain GE equalizer is proposed for orthogonal frequency division multiplexing(OFDM) systems with ...An efficient compensation scheme combining a timedomain Gaussian elimination(GE) channel estimator and a frequency-domain GE equalizer is proposed for orthogonal frequency division multiplexing(OFDM) systems with frequencydependent in-phase and quadrature-phase(IQ) imbalances at both transmitter and receiver.Compared with the traditional least square and least mean square compensation schemes,the proposed compensation scheme achieves the same bit error rate as the ideal IQ branches by using only two training OFDM symbols instead of about 20 OFDM symbols.展开更多
Thermal mechanical cyclic strain tests were carried out under in-phase andout-of-phase conditions on a Nickel-base Superalloy GH4133 in the temperature range of 571-823 degC. Based on analyzing the present models of T...Thermal mechanical cyclic strain tests were carried out under in-phase andout-of-phase conditions on a Nickel-base Superalloy GH4133 in the temperature range of 571-823 degC. Based on analyzing the present models of TMF (thermal mechanical fatigue) life prediction, a newmodel for predicting nickel-base superalloy TMF lifetime was proposed. TMF life of superalloy GH4133was calculated accurately based on the new model. Experimental TMF life has been compared with thecalculated results and all results fall in the scatter band of 1.5. The calculating results showthat the new model is not only simple, but also precise. This model will play great roles as lifeprediction of the metal materials and the engineering components subjected to non-isothermal serviceconditions.展开更多
The in-phase and quadrature-phase imbalance (IQI) is one of the major radio frequency impairments existing in orthogonal frequency division multiplexing (OFDM) systems with direct-conversion transceivers. During the t...The in-phase and quadrature-phase imbalance (IQI) is one of the major radio frequency impairments existing in orthogonal frequency division multiplexing (OFDM) systems with direct-conversion transceivers. During the transmission of the communication signal, the impact of IQI is coupled with channel impulse responses (CIR), which makes the traditional channel estimation schemes ineffective. A decoupled estimation scheme is proposed to separately estimate the frequency-dependent IQI and wireless channel. Firstly, the generalized channel model is built to separate the parameters of IQI and wireless channel. Then an iterative estimation scheme of frequency-dependent IQI is designed at the initial stage of communication. Finally, based on the estimation result of IQI, the least square algorithm is utilized to estimate the channel-related parameters at each time of channel variation. Compared with the joint estimation schemes of IQI and channel, the proposed decoupled estimation scheme requires much lower training overhead at each time of channel variation. Simulation results demonstrate the good estimation performance of the proposed scheme.展开更多
Optimization of mapping rule of bit-interleaved Turbo coded modulation with 16 quadrature amplitude modulation (QAM) is investigated based on different impacts of various encoded bits sequence on Turbo decoding perfor...Optimization of mapping rule of bit-interleaved Turbo coded modulation with 16 quadrature amplitude modulation (QAM) is investigated based on different impacts of various encoded bits sequence on Turbo decoding performance. Furthermore, bit-interleaved in-phase and quadrature phase (I-Q) Turbo coded modulation scheme are designed similarly with I-Q trellis coded modulation (TCM). Through performance evaluation and analysis, it can be seen that the novel mapping rule outperforms traditional one and the I-Q Turbo coded modulation can not achieve good performance as expected. Therefore, there is not obvious advantage in using I-Q method in bit-interleaved Turbo coded modulation.展开更多
文摘We numerically investigate the seven-core photonic crystal fiber (PCF) with the zero dispersion wavelength designed in the range of 1000 - 1080 nm, particularly suitable for the ytterbium-doped fiber laser pumping. Also, the PCFs are well designed for obtaining a flat in-phase mode by carefully adjusting the diameter of inner layer six holes, and the corresponding empirical values of fiber structure are summarized and listed. The variations of inner six holes to the amplitude of in-phase mode are further investigated, and our results show that a better tolerance can be achieved in the fiber structures with lower filling ratio configuration.
文摘Transition of flows past a pair of side-by-side circular cylinders are investigated by numerical simulations and the bifurcation analysis of the numerical results. Various flow patterns behind the cylinder-pair have been identified by the gap ratio (G) and Reynolds number (Re). This study focus on transition of in-phase and anti-phase vortex shedding synchronized forms. A nested Cartesian-grid formulation, in combination with an effective immersed boundary method and a two-step fractional-step procedure, has been adopted to simulate the flows. Numerical results reveal that the in-phase and anti-phase vortex shedding flows at Re = 100 can co-exist at 2.08 ≤G≤ 2.58. Hysteresis loop with increasing/decreasing G at constant Reynolds number Re = 100 is reported.
文摘The surface oxide film cracking behavior of Fe-30Ni-20Cr alloy under in-phase and out-of-phase synchronizing thermal cycling with mechanical cycling was studied.Surface oxide film cracking along the grain boundary under in-phase overlapping was creep predominant fracture mechanisms.Strongly induced slip lines preceding were accompanied by the surface oxide film cracking under Out-of phase,and the shear cracking was dominant mode.Negative mean stress could counteract a part of the tensile component of alternative stress,so as to delay the cracking process under in-phase,but positive mean stress overlapping the tensile alternative stress could accelerate the cycling cracking process under out-of-phase.
基金supported by the National Natural Science Foundation of China (Grant Nos.30370393,30640040)the NSF of Hubei Province (No.2007ABA098).
文摘Communication signals should be estimated by a single trial in a brain-computer interface.Since the relativity of visual evoked potentials from different sites should be stronger than those of the spontaneous electro-encephalogram(EEG),this paper adopted the time-lock averaged signals from multi-channels as features.200 trials of EEG recordings evoked by target or non-target stimuli were classified by the support vector machine(SVM).Results show that a classification accuracy of higher than 97%can be obtained by merely using the 250–550 ms time section of the averaged signals with channel Cz and Pz as features.It suggests that a possible approach to boost communication speed and simplify the designation of the brain-computer interface(BCI)system is worthy of an attempt in this way.
基金supported in part by the Minerva FoundationIsrael Science Foundation (ISF) Bikura foundation
文摘A novel method for converting an array of out-of-phase lasers into one of in-phase lasers that can be tightly focused is presented.The method exploits second-harmonic generation and can be adapted for different laser arrays geometries.Experimental and calculated results,presented for negatively coupled lasers formed in a square,honeycomb,and triangular geometries are in good agreement.
文摘From Shanghai to Haining Bafang Weaving Co., Ltd., through China’s busiest high way, we saw the adverts of Bafang Fabric on the side of the road. Upon the arriving in the downtown of Haining, the huge advert of Bafang Fabric attracts your eye --"advertising plus advertising to increase strength, that is, quality, and brand ".
基金This work was supported by the Research Program through the National Research Foundation of Korea,NRF-2019R1A2C1005920,S.K.
文摘Metamaterial surfaces play a vital role to achieve the surface waves suppression and in-phase reflection,in order to improve the antenna performance.In this paper,the performance comparison of a fifth generation(5G)antenna design is analyzed and compared with a metamaterial-based antenna for 5G communication system applications.Metamaterial surface is utilized as a reflector due to its in-phase reflection characteristic and high-impedance nature to improve the gain of an antenna.As conventional conducting ground plane does not give enough surface waves suppression which affects the antenna performance in terms of efficiency and gain etc.These factors are well considered in this work and improved by using the metamaterial surface.The radiating element of the proposed metamaterial based antenna is made up of copper material which is backed by the substrate,i.e.,Rogers-4003 with a standard thickness,loss tangent and a relative permittivity of 1.524 mm,0.0027 and 3.55,correspondingly.The proposed antenna with and without metamaterial surface operates at the central frequency of 3.32 GHz and 3.60 GHz,correspondingly.The traditional antenna yields a boresight gain of 2.76 dB which is further improved to 6.26 dB,using the metamaterial surface.The radiation efficiency of the proposed metamaterial-based 5G antenna is above 85%at the desired central frequency.
基金supported by the National Natural Science Fundation of China(6127123061172073)the Open Research Fund of National Mobile Communications Research Lab(2010D13)
文摘An efficient compensation scheme combining a timedomain Gaussian elimination(GE) channel estimator and a frequency-domain GE equalizer is proposed for orthogonal frequency division multiplexing(OFDM) systems with frequencydependent in-phase and quadrature-phase(IQ) imbalances at both transmitter and receiver.Compared with the traditional least square and least mean square compensation schemes,the proposed compensation scheme achieves the same bit error rate as the ideal IQ branches by using only two training OFDM symbols instead of about 20 OFDM symbols.
文摘Thermal mechanical cyclic strain tests were carried out under in-phase andout-of-phase conditions on a Nickel-base Superalloy GH4133 in the temperature range of 571-823 degC. Based on analyzing the present models of TMF (thermal mechanical fatigue) life prediction, a newmodel for predicting nickel-base superalloy TMF lifetime was proposed. TMF life of superalloy GH4133was calculated accurately based on the new model. Experimental TMF life has been compared with thecalculated results and all results fall in the scatter band of 1.5. The calculating results showthat the new model is not only simple, but also precise. This model will play great roles as lifeprediction of the metal materials and the engineering components subjected to non-isothermal serviceconditions.
基金supported by the National Natural Science Foundation of China(6140123261471200+4 种基金6150124861501254)the China Postdoctoral Science Foundation(2014M561692)the Jiangsu Province Postdoctoral Science Foundation(1402087C)the NUPTSF(NY213063)
文摘The in-phase and quadrature-phase imbalance (IQI) is one of the major radio frequency impairments existing in orthogonal frequency division multiplexing (OFDM) systems with direct-conversion transceivers. During the transmission of the communication signal, the impact of IQI is coupled with channel impulse responses (CIR), which makes the traditional channel estimation schemes ineffective. A decoupled estimation scheme is proposed to separately estimate the frequency-dependent IQI and wireless channel. Firstly, the generalized channel model is built to separate the parameters of IQI and wireless channel. Then an iterative estimation scheme of frequency-dependent IQI is designed at the initial stage of communication. Finally, based on the estimation result of IQI, the least square algorithm is utilized to estimate the channel-related parameters at each time of channel variation. Compared with the joint estimation schemes of IQI and channel, the proposed decoupled estimation scheme requires much lower training overhead at each time of channel variation. Simulation results demonstrate the good estimation performance of the proposed scheme.
文摘Optimization of mapping rule of bit-interleaved Turbo coded modulation with 16 quadrature amplitude modulation (QAM) is investigated based on different impacts of various encoded bits sequence on Turbo decoding performance. Furthermore, bit-interleaved in-phase and quadrature phase (I-Q) Turbo coded modulation scheme are designed similarly with I-Q trellis coded modulation (TCM). Through performance evaluation and analysis, it can be seen that the novel mapping rule outperforms traditional one and the I-Q Turbo coded modulation can not achieve good performance as expected. Therefore, there is not obvious advantage in using I-Q method in bit-interleaved Turbo coded modulation.