Recent advances in the in-plane shear testing of Mg alloy sheets

Sheet-metal products are integral parts of engineering industries and academia research. Various testing techniques have revealed the deformation behaviors of sheet metals under complex stress states. Information obtained from tensile and compression tests, however, are insufficient for the identification of material parameters relevant to modern constitutive laws, which require experimental setups capable of generating various loading conditions and applying great amounts of strain to sheet metals. In-plane shear testing has emerged as an important method to overcome the challenges associated with tension and compression tests and can provide additional information about deformation behaviors under large plastic strains. Materials such as Mg alloys with poor levels of both ductility and formability cannot accommodate large plastic strains. Therefore, tension and compression tests have limitations in explaining the material behaviors that occur during sheet metal forming where large plastic strains are introduced. Many studies have been conducted to explain the deformation behaviors of Mg alloys under shear deformation techniques. These include severe plastic deformation(SPD), especially the equal channel angular pressing(ECAP)and equal channel angular extrusion, rolling combined with shear deformation i.e. differential speed rolling(DSR), and also in-plane shear for sheet metals, particularly under large levels of plastic strain. These in-plane shear technique involves the Miyauchi shear test, ASTM shear test, and twin bridge shear tests. Moreover, many experimental results have revealed that the evolution of microstructure and texture during in-plane shear is closely related to the failure behavior of materials. Therefore, this review is focused on techniques for in-plane shear testing that have been reported thus far, on the effect of in-plane shear on the microstructure development of Mg alloy sheets, and on the usefulness of in-plane shear testing to evaluate the formability of Mg alloy sheets.

Effect of holes on in-plane shear(Mode Ⅱ) crack sub-critical propagation of rock

Shear-box(i.e.compression-shear) test and newly designed electrically conductive adhesive method were used to measure shear crack sub-critical propagation time and rate of sandstone specimen.Different cubic specimens with and without holes were tested to study the effect of holes on the shear crack sub-critical propagation.Numerical and experimental results show that three independent variables of hole,the interval distance S,the distance between the center of hole and the crack tip L,and hole radius R,have different contribution to the ratio of stress intensity factor of the specimen with holes to that of the specimen without hole,KⅡ/KⅡ0.Increasing S and decreasing L and R will result in the decrease of KⅡ/KⅡ0 and help crack arrest.The weight relation of the independent variables for KⅡ/KⅡ0 is S>L>R.The specimen DH3 with the largest value of S and the smallest values of L and R has the longest sub-critical crack propagation time and the smallest sub-critical crack propagation rate.Adding two suitable holes symmetrically to the original crack plane in rock specimen is considered to be a potential method for crack arrest of rock.

In-plane shear(ModeⅡ) crack sub-critical propagation of rock at high temperature

In-plane shear crack sub-critical propagation of rock at high temperature was studied by finite element method and shear-box(i.e.compression-shear) test with newly designed electrically conductive adhesive method.Numerical and experimental results show that the normalized shear(Mode Ⅱ) stress intensity factors,K ⅡT/KT0 is decreased as the temperature increases because high temperature can improve stress distribution at crack tip and reduce the Mode Ⅱ stress intensity factor.Microscopic features of fractured surface are of little pits and secondary micro-cracks in the vicinity(1.5-4.0 mm) of the crack tip.The chevron-shape secondary cracks gradually merge in the length of about 4-5 mm and disappear along the direction of crack propagation.Stable shear crack propagation time is increased with the increasing temperature while the stable shear crack propagation rate is decreased with the increasing temperature,since high temperature can increase the shear(Mode Ⅱ) fracture toughness and prevent the crack growth.It is necessary to ensure the ligament of specimen long enough to measure the maximum unstable crack propagation rate of rock.

In-Plane Shear Performance of Wood-Framed Drywall Sheathing Wall Systems under Cyclic Racking Loading

A pilot study was conducted at Penn State University to determine whether the type of drywall joint compound would influence the shear strength of wood-frame stud walls sheathed with Gypsum Wall Board (GWB or drywall). In this study, five 2438 mm by 2438 mm specimens were tested under in-plane cyclic racking loading following the CUREE loading protocol for light-frame wall systems. Three specimens were finished using non-cement based joint compound while the other two used cement based joint compound. Based on the experimental testing of the specimens, the results show that the use of cement based joint compound on drywall joints produces higher shear capacity for the wall system as compared to similar specimens finished with conventional non-cement based joint compound. The result of the study is particularly important for high seismic regions where interior stud walls in residential construction effectively take part in seismic resistance even though wood shear walls are normally used on exterior walls.

Evaluation of in-plane shear test methods for composite material laminates

In-plane shear properties of composite material laminates are very important in structural design of composite material. Four commonly used in-plane shear test methods were introduced in this paper. In order to study the differences of various shear test methods, two ASTM standard in-plane shear test methods for composite material laminates were experimentally investigated. They are ±45° tensile shear test (ASTM D3518) and V-notched rail shear test (ASTM D7078). Five types of composite material laminates composed of E-glass fiber fabric and vinyl ester resin were utilized, whose stacking sequences are 03s, 0/903s, CSM/0/902s, ±453s and (0/90)2/(±45)2/(0/90)2s, respectively. The test results indicate that the ±45° tensile shear test can predict shear moduli of composite material laminates accurately. However, the predictions of shear strength using ±45° tensile shear test are significantly lower than those of V-notched rail shear test.

Recent advances and key opportunities on in-plane micro-supercapacitors:From functional microdevices to smart integrated microsystems

The popularization of portable,implantable and wearable microelectronics has greatly stimulated the rapid development of high-power planar micro-supercapacitors(PMSCs).Particularly,the introduction of new functionalities(e.g.,high voltage,flexibility,stretchability,self-healing,electrochromism and photo/thermal response)to PMSCs is essential for building multifunctional PMSCs and their smart selfpowered integrated microsystems.In this review,we summarized the latest advances in PMSCs from various functional microdevices to their smart integrated microsystems.Primarily,the functionalities of PMSCs are characterized by three major factors to emphasize their electrochemical behavior and unique scope of application.These include but are not limited to high-voltage outputs(realized through asymmetric configuration,novel electrolyte and modular integration),mechanical resilience that includes various feats of flexibility or stretchability,and response to stimuli(self-healing,electrochromic,photo-responsive,or thermal-responsive properties).Furthermore,three representative integrated microsystems including energy harvester-PMSC,PMSC-energy consumption,and all-in-one selfpowered microsystems are elaborately overviewed to understand the emerging intelligent interaction models.Finally,the key perspectives,challenges and opportunities of PMSCs for powering smart microelectronics are proposed in brief.

Tunnel effect of fractal fault and transient S-wave velocity rupture (TSVR) of in-plane shear fault

Transient S wave velocity rupture (TSVR) means the velocity of fault rupture propagation is between S wave velocity α and P wave velocity β . Its existing in the rupture of in plane ( i.e . strike slip) fault has been proved, but in 2 dimensional classical model, there are two difficulties in transient S wave velocity rupture, i.e ., initialization difficulty and divergence difficulty in interpreting the realization of TSVR. The initialization difficulty means, when v ↑ v R (Rayleigh wave velocity), the dynamic stress strength factor K 2(t) →+0, and changes from positive into negative in the interval ( v R, β ). How v transit the forbidden of ( v R, β )? The divergence difficulty means K 2(t) →+∞ when v ↓ β . Here we introduce the concept of fractal and tunnel effect that exist everywhere in fault. The structure of all the faults is fractal with multiple cracks. The velocity of fault rupture is differentiate of the length of the fault respect to time, so the rupture velocity is also fractal. The tunnel effect means the dynamic rupture crosses over the interval of the cracks, and the coalescence of the intervals is slower than the propagation of disturbance. Suppose the area of earthquake nucleation is critical or sub critical propagation everywhere, the arriving of disturbance triggers or accelerates the propagation of cracks tip at once, and the observation system cannot distinguish the front of disturbance and the tip of fracture. Then the speed of disturbance may be identified as fracture velocity, and the phenomenon of TSVR appears, which is an apparent velocity. The real reason of apparent velocity is that the mathematics model of shear rupture is simplified of complex process originally. The dual character of rupture velocity means that the apparent velocity of fault and the real velocity of micro crack extending, which are different in physics, but are unified in rupture criterion. Introducing the above mentioned concept to the calculation of K 2 (t) , the difficulty of initialization can be overcome, and the integral equation of triggering the initialization of TSVR is given quantitatively. By solving this integral equation, the lower limit of TSVR is 1.105 3 β , not β , and the divergence difficulty is overcome. TSVR is unstable solution, and may degenerate to sub Rayleigh wave velocity rupture immediately where the non critical condition can be measured. The results of this paper show that the initialization and continuum depends on the condition of earthquake nucleation in seismogenic area.

One-photo excitation pathway in 2D in-plane heterostructures for effective visible-light-driven photocatalytic degradation

Broad-spectrum absorption and highly effective charge-carrier separation are two essential requirements to improve the photocatalytic performance of semiconductor-based photocatalysts.In this work,a fascinating one-photon system is reported by rationally fabricating 2D in-plane Bi_(2)O_(3)/BiOCl(i-Cl)heterostructures for efficient photocatalytic degradation of RhB and TC.Systematic investigations revealed that the matched band structure generated an internal electric field and a chemical bond connection between the Bi_(2)O_(3)and BiOCl in the Bi_(2)O_(3)/BiOCl composite that could effectively improve the utilization ratio of visible light and the separation effectivity of photo-generated carriers in space.The formed interactions at the 2D in-plane heterojunction interface induced the one-photon excitation pathway which has been confirmed by the experiment and DFT calculations.As a result,the i-Cl samples showed significantly enhanced photocatalytic efficiency towards the degradation of RhB and TC(RhB:0.106 min^(-1);TC:0.048 min^(-1))under visible light.The degradation activities of RhB and TC for i-Cl were 265.08 and 4.08times that of pure BiOCl,as well as 9.27 and 2.14 times that of mechanistically mixed Bi_(2)O_(3)/BiOCl samples,respectively.This work provides a logical strategy to construct other 2D in-plane heterojunctions with a one-photon excitation pathway with enhanced performance.

Failure transition of shear-to-dilation band of rock salt under triaxial stresses

Great potential of underground gas/energy storage in salt caverns seems to be a promising solution to support renewable energy.In the underground storage method,the operating cycle unfortunately may reach up to daily or even hourly,which generates complicated pressures on the salt cavern.Furthermore,the mechanical behavior of rock salt may change and present distinct failure characteristics under different stress states,which affects the performance of salt cavern during the time period of full service.To reproduce a similar loading condition on the cavern surrounding rock mass,the cyclic triaxial loading/unloading tests are performed on the rock salt to explore the mechanical transition behavior and failure characteristics under different confinement.Experimental results show that the rock salt samples pre-sent a diffused shear failure band with significant bulges at certain locations in low confining pressure conditions(e.g.5 MPa,10 MPa and 15 MPa),which is closely related to crystal misorientation and grain boundary sliding.Under the elevated confinement(e.g.20 MPa,30 MPa and 40 MPa),the dilation band dominates the failure mechanism,where the large-size halite crystals are crushed to be smaller size and new pores are developing.The failure transition mechanism revealed in the paper provides additional insight into the mechanical performance of salt caverns influenced by complicated stress states.

Anisotropic time-dependent behaviors of shale under direct shearing and associated empirical creep models

Understanding the anisotropic creep behaviors of shale under direct shearing is a challenging issue.In this context,we conducted shear-creep and steady-creep tests on shale with five bedding orientations (i.e.0°,30°,45°,60°,and 90°),under multiple levels of direct shearing for the first time.The results show that the anisotropic creep of shale exhibits a significant stress-dependent behavior.Under a low shear stress,the creep compliance of shale increases linearly with the logarithm of time at all bedding orientations,and the increase depends on the bedding orientation and creep time.Under high shear stress conditions,the creep compliance of shale is minimal when the bedding orientation is 0°,and the steady-creep rate of shale increases significantly with increasing bedding orientations of 30°,45°,60°,and 90°.The stress-strain values corresponding to the inception of the accelerated creep stage show an increasing and then decreasing trend with the bedding orientation.A semilogarithmic model that could reflect the stress dependence of the steady-creep rate while considering the hardening and damage process is proposed.The model minimizes the deviation of the calculated steady-state creep rate from the observed value and reveals the behavior of the bedding orientation's influence on the steady-creep rate.The applicability of the five classical empirical creep models is quantitatively evaluated.It shows that the logarithmic model can well explain the experimental creep strain and creep rate,and it can accurately predict long-term shear creep deformation.Based on an improved logarithmic model,the variations in creep parameters with shear stress and bedding orientations are discussed.With abovementioned findings,a mathematical method for constructing an anisotropic shear creep model of shale is proposed,which can characterize the nonlinear dependence of the anisotropic shear creep behavior of shale on the bedding orientation.

State-of-the-art on the anchorage performance of rock bolts subjected to shear load

Rock bolts are extensively utilized in underground engineering as a means of offering support and stability to rock masses in tunnels,mines,and other underground structures.In environments of high ground stress,faults or weak zones can frequently arise in rock formations,presenting a significant challenge for engineering and potentially leading to underground engineering collapse.Rock bolts serve as a crucial structural element for the transmission of tensile stress and are capable of withstanding shear loads to prevent sliding of weak zones within rock mass.Therefore,a complete understanding of the behavior of rock bolts subjected to shear loads is essential.This paper presents a state-of-the-art review of the research progress of rock bolts subjected to shear load in three categories:experiment,numerical simulation,and analytical model.The review focuses on the research studies and developments in this area since the 1970s,providing a comprehensive overview of numerous factors that influence the anchorage performance of rock bolts.These factors include the diameter and angle of the rock bolt installation,rock strength,grouting material,bolt material,borehole diameter,rock bolt preload,normal stress,joint surface roughness and joint expansion angle.The paper reviews the improvement of mechanical parameter setting in numerical simulation of rock bolt shear.Furthermore,it delves into the optimization of the analytical model concerning rock bolt shear theory,approached from the perspectives of both Elastic foundation beam theory coupled with Elastoplasticity theory and Structural mechanic methods.The significance of this review lies in its ability to provide insights into the mechanical behavior of rock bolts.The paper also highlights the limitations of current research and guidelines for further research of rock bolts.

Mechanical behaviors of backfill-rock composites: Physical shear test and back-analysis

The shear behavior of backfill-rock composites is crucial for mine safety and the management of surface subsidence.For exposing the shear failure mechanism of backfill-rock composites,we conducted shear tests on backfill-rock composites under three constant normal loads,compared with the unfilled rock.To investigate the macro-and meso-failure characteristics of the samples in the shear tests,the cracking behavior of samples was recorded by a high-speed camera and acoustic emission monitoring.In parallel with the experimental test,the numerical models of backfill-rock composites and unfilled rock were established using the discrete element method to analyze the continuous-discontinuous shearing process.Based on the damage mechanics and statistics,a novel shear constitutive model was proposed to describe mechanical behavior.The results show that backfill-rock composites had a special bimodal phenomenon of shearing load-deformation curve,i.e.the first shearing peak corresponded to rock break and the second shearing peak induced by the broken of aeolian sand-cement/fly ash paste backfill.Moreover,the shearing characteristic curves of the backfill-rock composites could be roughly divided into four stages,i.e.the shear failure of the specimens experienced:stage I:stress concentration;stage II:crack propagation;stage III:crack coalescence;stage IV:shearing friction.The numerical simulation shows that the existence of aeolian sand-cement/fly ash paste backfill inevitably altered the coalescence type and failure mode of the specimens and had a strengthening effect on the shear strength of backfillrock composites.Based on damage mechanics and statistics,a shear constitutive model was proposed to describe the shear fracture characteristics of specimens,especially the bimodal phenomenon.Finally,the micro-and meso-mechanisms of shear failure were discussed by combining the micro-test and numerical results.The research can advance the better understanding of the shear behavior of backfill-rock composites and contribute to the safety of mining engineering.

Shear band evolution and acoustic emission characteristics of sandstone containing non-persistent flaws

Direct shear tests were conducted on sandstone specimens under different constant normal stresses to study the coalescence of cracks between non-persistent flaws and the shear sliding characteristics of the shear-formed fault.Digital image correlation and acoustic emission(AE)techniques were used to monitor the evolution of shear bands at the rock bridge area and microcracking behaviors.The experimental results revealed that the shear stresses corresponding to the peak and sub-peak in the stressdisplacement curve are significantly affected by the normal stress.Strain localization bands emerged at both the tip of joints and the rock bridge,and their extension and interaction near the peak stress caused a surge in the AE hit rate and a significant decrease in the AE b value.Short and curvilinear strain bands were detected at low normal stress,while high normal stress generally led to more microcracking events and longer coplanar cracks at the rock bridge area.Furthermore,an increase in normal stress resulted in a higher AE count rate and more energetic AE events during friction sliding along the shearformed fault.It was observed that the elastic energy released during the crack coalescence at the prepeak stage was much greater than that released during friction sliding at the post-peak stage.More than 75%of AE events were located in the low-frequency band(0e100 kHz),and this proportion continued to rise with increasing normal stress.Moreover,more AE events of low AF value and high RA value were observed in specimens subjected to high normal stress,indicating that greater normal stress led to more microcracks of shear nature.

Retraction to: Shear strength of extremely altered serpentinites based on degree of saturation (Ankara, Turkey)

The Editor in Chief has retracted this article.After publication,concerns were raised over potentially inconsistent data-for example,the author mentioned residual soil with silt fraction,but Fig.5 shows even the smallest grains are beyond silt grains.Further analysis showed that Fig.6 and Fig.9 show both loose and dense soils exhibiting very similar dilatance behaviour,which is not typical.The author shared raw data,but it was incomplete and could not be verified.The Editor in Chief,therefore,has lost confidence in the findings of this article.The author does not agree to this retraction.

Seismic performance evaluation of hybrid coupled shear wall system with shear and flexural fuse-type steel coupling beams

Replaceable flexural and shear fuse-type coupling beams are used in hybrid coupled shear wall(HCSW)systems,enabling concrete buildings to be promptly recovered after severe earthquakes.This study aimed to analytically evaluate the seismic behavior of flexural and shear fuse beams situated in short-,medium-and high-rise RC buildings that have HCSWs.Three building groups hypothetically located in a high seismic hazard zone were studied.A series of 2D nonlinear time history analyses was accomplished in OpenSees,using the ground motion records scaled at the design basis earthquake level.It was found that the effectiveness of fuses in HCSWs depends on various factors such as size and scale of the building,allowable rotation value,inter-story drift ratio,residual drift quantity,energy dissipation value of the fuses,etc.The results show that shear fuses better meet the requirements of rotations and drifts.In contrast,flexural fuses dissipate more energy,but their sectional stiffness should increase to meet other requirements.It was concluded that adoption of proper fuses depends on the overall scale of the building and on how associated factors are considered.

Photoacoustic elastography based on laser-excited shear wave

Elastography can be used as a diagnostic method for quantitative characterization of tissue hardness information and thus,differential changes in pathophysiological states of tissues.In this study,we propose a new method for shear wave elastography(SWE)based on laser-excited shear wave,called photoacoustic shear wave elastography(PASWE),which combines photoacoustic(PA)technology with ultrafast ultrasound imaging.By using a focused laser to excite shear waves and ultrafast ultrasonic imaging for detection,high-frequency excitation of shear waves and noncontact elastic imaging can be realized.The laser can stimulate the tissue with the light absorption characteristic to produce the thermal expansion,thus producing the shear wave.The frequency of shear wave induced by laser is higher and the frequency band is wider.By tracking the propagation of shear wave,Young’s modulus of tissue is reconstructed in the whole shear wave propagation region to further evaluate the elastic information of tissue.The feasibility of the method is verified by experiments.Compared with the experimental results of supersonic shear imaging(SSI),it is proved that the method can be used for quantitative elastic imaging of the phantoms.In addition,compared with the SSI method,this method can realize the noncontact excitation of the shear wave,and the frequency of the shear wave excited by the laser is higher than that of the acoustic radiation force(ARF),so the spatial resolution is higher.Compared to the traditional PA elastic imaging method,this method can obtain a larger imaging depth under the premise of ensuring the imaging resolution,and it has potential application value in the clinical diagnosis of diseases requiring noncontact quantitative elasticity.

On the calibration of a shear stress criterion for rock joints to represent the full stress-strain profile

Conventional numerical solutions developed to describe the geomechanical behavior of rock interfaces subjected to differential load emphasize peak and residual shear strengths.The detailed analysis of preand post-peak shear stress-displacement behavior is central to various time-dependent and dynamic rock mechanic problems such as rockbursts and structural instabilities in highly stressed conditions.The complete stress-displacement surface(CSDS)model was developed to describe analytically the pre-and post-peak behavior of rock interfaces under differential loads.Original formulations of the CSDS model required extensive curve-fitting iterations which limited its practical applicability and transparent integration into engineering tools.The present work proposes modifications to the CSDS model aimed at developing a comprehensive and modern calibration protocol to describe the complete shear stressdisplacement behavior of rock interfaces under differential loads.The proposed update to the CSDS model incorporates the concept of mobilized shear strength to enhance the post-peak formulations.Barton’s concepts of joint roughness coefficient(JRC)and joint compressive strength(JCS)are incorporated to facilitate empirical estimations for peak shear stress and normal closure relations.Triaxial/uniaxial compression test and direct shear test results are used to validate the updated model and exemplify the proposed calibration method.The results illustrate that the revised model successfully predicts the post-peak and complete axial stressestrain and shear stressedisplacement curves for rock joints.

Shear behavior and off-fault damage of saw-cut smooth and tension-induced rough joints in granite

The damage of rock joints or fractures upon shear includes the surface damage occurring at the contact asperities and the damage beneath the shear surface within the host rock.The latter is commonly known as off-fault damage and has been much less investigated than the surface damage.The main contribution of this study is to compare the results of direct shear tests conducted on saw-cut planar joints and tension-induced rough granite joints under normal stresses ranging from 1 MPa to 50 MPa.The shear-induced off-fault damages are quantified and compared with the optical microscope observation.Our results clearly show that the planar joints slip stably under all the normal stresses except under 50 MPa,where some local fractures and regular stick-slip occur towards the end of the test.Both post-peak stress drop and stick-slip occur for all the rough joints.The residual shear strength envelopes for the rough joints and the peak shear strength envelope for the planar joints almost overlap.The root mean square(RMS)of asperity height for the rough joints decreases while it increases for the planar joint after shear,and a larger normal stress usually leads to a more significant decrease or increase in RMS.Besides,the extent of off-fault damage(or damage zone)increases with normal stress for both planar and rough joints,and it is restricted to a very thin layer with limited micro-cracks beneath the planar joint surface.In comparison,the thickness of the damage zone for the rough joints is about an order of magnitude larger than that of the planar joints,and the coalesced micro-cracks are generally inclined to the shear direction with acute angles.The findings obtained in this study contribute to a better understanding on the frictional behavior and damage characteristics of rock joints or fractures with different roughness.

Roughness characterization and shearing dislocation failure for rock-backfill interface

Shearing dislocation is a common failure type for rock–backfill interfaces because of backfill sedimentation and rock strata movement in backfill mining goaf.This paper designed a test method for rock–backfill shearing dislocation.Using digital image techno-logy and three-dimensional(3D)laser morphology scanning techniques,a set of 3D models with rough joint surfaces was established.Further,the mechanical behavior of rock–backfill shearing dislocation was investigated using a direct shear test.The effects of interface roughness on the shear–displacement curve and failure characteristics of rock–backfill specimens were considered.The 3D fractal dimen-sion,profile line joint roughness coefficient(JRC),profile line two-dimensional fractal dimension,and the surface curvature of the frac-tures were obtained.The correlation characterization of surface roughness was then analyzed,and the shear strength could be measured and calculated using JRC.The results showed the following:there were three failure threshold value points in rock–backfill shearing dis-location:30%–50%displacement before the peak,70%–90%displacement before the peak,and 100%displacement before the peak to post-peak,which could be a sign for rock–backfill shearing dislocation failure.The surface JRC could be used to judge the rock–backfill shearing dislocation failure,including post-peak sliding,uniform variations,and gradient change,corresponding to rock–backfill disloca-tion failure on the field site.The research reveals the damage mechanism for rock–backfill complexes based on the free joint surface,fills the gap of existing shearing theoretical systems for isomerism complexes,and provides a theoretical basis for the prevention and control of possible disasters in backfill mining.

Effect of Dietary Components on the Shear Bond Strength of Orthodontics Brackets after Thermal Aging

Introduction: The stability of orthodontic brackets throughout orthodontic treatment plays a critical role in the treatment’s effectiveness. The present in vitro study was designed to assess the impact of various dietary components on the performance of orthodontic brackets. Methods: Metal orthodontic brackets were bonded to 66 extracted anterior teeth divided into groups based on the solution type: Milk, Gatorade, Cold Coffee, and a control group using water. Each group consisted of 20 teeth except for the control group, which included six teeth. The bracketed teeth were submerged in their respective solutions for 15 minutes three times daily at different intervals to mimic an in vivo environment and were stored in artificial saliva at room temperature (23?C). The specimens underwent artificial aging through 10,000 cycles of thermocycling (representing one clinical year) between 5?C and 55?C. Shade measurements were taken using a VITA Easy Shade device, capturing the classic shade and L*, a*, and b* values. Delta E values were calculated immediately post-bonding and after 7 days, 1 month, 1, and 2 clinical years. The shear bond strength of each bracket was measured using an ultra-tester machine. Results: After two clinical years, significant differences in ΔE color values were observed across all groups, with the most substantial change noted in teeth immersed in cold coffee. Brackets submerged in milk demonstrated lower shear bond strength than other solutions, whereas the control group exhibited the highest shear bond strength (P = 0.01). Conclusion: The study indicates that dietary components significantly influence tooth color stability and the shear bond strength of orthodontic brackets, underscoring the importance of considering these factors in orthodontic treatment planning.