Investigation on welding procedures for in-service pipelines

Some research results are given in this paper about burnthrough and hydrogen cracking with a flowing chamber and a loop. Many factors including plate thickness, running rate, heat input and so forth have been studied. By experiments it can be found that occurrence of hydrogen cracking can be effectively reduced by properly increasing heat input and using the tempering bead technique.

Study on the microstructure and hardness of in-service welded joint of X70 pipeline steel

Hydrogen induced cracking （HIC） is one of the main problems of in-service welding onto active pipeline. Microstructure and hardness of welded joint have a vital effect on hydrogen induced cracking. The microstructure and hardness of welded joint of XTO pipeline steel were studied using simulation in-service welding device. The results show that the main microstructures of in-service welded seam are grain boundary ferrite , intracrystalline acicular ferrite , as well as small amount of widmanztatten structure. The main microstructures of coarse grain heat-affected zone （CGHAZ） are coarse granular bainite, lath ferrite and martensite. Metastable phases such as martensite and lath ferrite are found in CGHAZ because of the too quick cooling velocity a＇nd the hardness of the CGHAZ is high.

FAILURE ANALYSIS AND INSPECTION OF CRACKING OF IN-SERVICE CATALYTIC REGENERATOR

The special subject 'research on life prediction technology of important in-service pressure' mainly analyzes the failure mechanism of large-sized important and criticalin-service pressure vessels under the action of working medium and investigates safety assessmentand life prediction technology with a view to enhance the operation reliability of in-servicepressure vessels in China. Based on a series of accident investigation and test & measuringresearch, the cause of cracking of catalytic regenerator is analyzed and the in-line non-destructiveexamination method and failure prevention measures for the cracking of catalytic regenerator areproposed.

Influence of cooling conditions on X70 pipeline steel in-service welding HAZ

The chamber device was designed and set up to simulate the in-service welding. The results show ： the t8/5 , t8/3 and inner wall peak temperature Tp decrease with the cooling rate increases. The welding energy is carried off by flowing medium, the cooling rate increases, and many unbalanced microstructures such as granular bainite, martensite and M-A generate ; it worsens the properties of HAZ. Under air-cooling, the cooling rate is slow, the austenite grain grows obviously, the lath ferrite crosses the whole austenite, and it causes the hardness value is also big. The change of HAZ width is not obvious with the increase of cooling rate; and burn-through is not susceptible to the cooling rate. The quench microstructures increase and the hydrogen does not outflow from the HAZ easily when increase the cooling rate, so the susceptibility of hydrogen cracking increases.

Non-destructive Testing Robots （NDTBOTs） for In-Service Storage Tank Inspection

Petrochemical storage tanks are generally inspected when the tank is offline mostly to assess the extent of underside corrosion on the tank floor. Emptying, cleaning and opening a tank for inspection take many months and are very expensive. Inspection costs can be reduced significantly by inserting robots through manholes on the tank roof to pertbrm non-destructive testing （NDT）. The challenge is to develop robots that can operate safely in explosive and hazardous environments and measure the thickness of floor plates using ultrasound sensors. This paper reports on the development of a small and inexpensive prototype robot （NDTBOT） which is designed to be intrinsically safe for zone zero operation. The robot ＂hops＂ across the floor to make measurements, without any external moving parts. The paper describes the design, experimental testing of the NDTBOT and presents results of steel plate thickness measurements made under water.

Numerical simulation of mechanical properties of straight pipe and elbow during in-service welding

Elbows are the most vulnerable parts in pipeline network systems. The residual stress for in-service welding repair has significant impacts on the mechanical properties of straight pipes and elbows. In this paper,the thermal elastic-plastic finite element method is employed to investigate the mechanical field during the in-service welding. The prediction of residual stress and deformation in the straight pipe and elbow is performed based on the validation of the numerical models. And the effects of the curvature radius and defects on the elbow are investigated. The results show that the residual stress distribution is uneven along various directions after welding. And the mechanical properties of the elbow decrease when the curvature radius is small. Compared to the intact elbow,the residual stress of the elbow with defects concentrates in the defective area. The depth of defect is the main factors affecting the mechanical properties of the elbow. A systematic analysis of the mechanical properties of straight pipes and elbows is proposed to provide guidance to the in-service welding.

Numerical simulation of stress and deformation of in-service welding onto gas pipeline

SYSWELD was used to simulate in-service welding process of gas pipeline of X70 pipeline steel. Welding thermal cycle, stress and deformation of in-service welded joint were studied. The results show that peak temperature of coarse grain heat-affected zone （CGHAZ） of in-service welding onto gas pipeline is the same with routine welding, but ts/5, ts/3 and ts/1 decrease at certain degree. For the zone near welded seam, axial stress and hoop stress in the inner pipe wall are compressive stress when welding source passes through the cross-section that is studied, but residual axial stress and residual hoop stress after welded are all tensile stress. Transient deformation and residual deformation are all convex deformation compared with the original pipe diameter size. Deformation achieves maximum when welding thermal source passes through the cross-section that is studied and then decreases during the cooling process after welding.

Influence of pipe parameters and heat input on thermal cycle of in-service welding onto active gas pipeline

The software of SYSWELD was used to build model and simulate thermal cycle of in-service welding onto active gas pipeline. Influence of pipe diameter, wall thickness and heat input on thermal cycle was studied. The results show that t8/5 , t8/3 and peak temperature of inner surface decrease when wall thickness increases from 5 mm to 12 mm. But t8/1 will increases with the increase of wall thickness and will decrease after the wall thickness is larger than 7 mm. Pipe diameter has little influence on thermal cycle and that influence can be ignored when pipe diameter is greater than 273 mm. t8/5 , t8/3 , t8/1 and peak temperature of inner surface will increase with the increase of heat input.

Effect of In-Service Training Program on the Practice of Healthcare Workers toward Malaria Prevention and Treatment Guidelines during Pregnancy in Health Facilities in Jowhar District, Somalia

Malaria is generally considered a major public health problem in Somalia. Providing early diagnosis and effective treatment is the key element of malaria control strategies in malaria-endemic countries, including Somalia. This required to advocate and ensure health worker’s adherence to the national malaria guidelines at all levels of health care service. A well-designed in-service training program may improve the level of health worker’s adherence to national malaria treatment guidelines, although results have been inconsistent. This is an interventional health facility-based pre and post comparative study aimed to assess the effect of an in-service training program on the practice of healthcare workers toward malaria prevention and treatment guidelines, during in pregnancy in health facilities in Jowhar district, Middle Shabelle region of Somalia. The study was implemented in three phases: pre-intervention phase, intervention phase and post-intervention phase. The sample size consisted of (n = 150) health workers who were selected from ten public health facilities using proportional to size sampling;the data collection adopted in this research is composed of a structured interview questionnaire and observational checklist. Data was analyzed through the application of descriptive statistical analysis that includes frequency and percentage and the Chi-square (x2) test was used to test the associations among variables using SPSS software version 25. The study showed that the level of health workers’ awareness of the national malaria guidelines in the treatment and prevention of malaria in pregnancy was found to be good before the intervention 89 (59.3%) and this proportion increased to 150 (100%) post-intervention of the training program. A significance difference has been observed between health workers’ awareness and their adherence to the malarial guidelines at pre-test and post-test with a p-value 0.000. The proportion of health workers who attended previous training on national malaria guidelines in the treatment and prevention of malaria in pregnancy increased from 46 (30.7%) at the pre-test to 150 (100%) after the post-test. A significant difference was observed in the training status among different categories of health worker and their adherence to the guidelines during the pre- and post-intervention of the training program, with a p-value of 0.000. The result showed that health workers were adhering to the guidelines at the pre-test 33 (22%), this increased after the post-test to 87 (58%). The knowledge of the need to adhere led to an increase in the adherence rate after the training program intervention. The study reveals that inadequate awareness was most reason for the non-adherence in the majority of the health workers as indicated by 89 (59.3%) at the pre-test and 56 (37.3%) in the post-test. However, difference was not significant between the availability of anti-malaria drugs in the facilities and the health workers’ adherence to the guidelines p-value 0.355 at the pretest and p-value 0.258 at post-test. The study concluded that the in-service training program significantly improved health workers’ knowledge and practice to the national malaria guidelines in the treatment, and prevention of malaria in pregnancy. The researcher recommends that the national malaria control programme (NMCP) of the Federal Ministry of Health should provide continuous regular in-service training to frontline healthcare workers at (facility and Community-based) to upgrade their skills and knowledge towards the malaria guidelines, disseminate job aids to the health facilities and undertake regular monitoring to ensure effective implementation of the national malaria treatment guidelines in the treatment and prevention of malaria in pregnancy in achieving desired proper case-management practices of malaria in pregnancy at all levels of health care service.

Investigation and Analysis of Continuing Nursing Education Status and Needs of In-Service Nurses in Tibet

Objective: To investigate and analyze the current status of continuing nursing education (CNE) of in-service nurses in Tibet and their demand for continuing education. Methods: 663 active nurses in Tibet were taken as the research objects, and the self-developed questionnaire was used to investigate the current status and needs of CNE, and the correlation between the CNE needs of active nurses and their personal conditions was analyzed. Results: This study shows that 65.61% (435/663) of active nurses have not participated in any CNE, and 91.86% (609/663) of active nurses believe that they need to participate in CNE. The problems faced by active nurses in participating in CNE include funding restrictions, time limitation and ability limitation. Logistic stepwise regression analysis reveals that the age of active nurses and working years of nurses are negatively correlated with the funding restrictions for participating in CNE (P < 0.05). It is relatively more difficult for young nurses with less working experience to obtain funding for participating in CNE. Moreover, there is a negative correlation between age, educational level and the ability of nurses to participate in CNE (P < 0.05). Younger nurses with lower educational level are more difficult to participate in CNE due to personal ability. There is a positive correlation between the length of working experience and the time limitation faced to participate in CNE (P < 0.05). Senior nurses are too busy with their work to participate in CNE due to limited time. Conclusion: The problems faced by active nurses in Tibet in participating in CNE come from funding, time and ability. Young nurses with limited working experience cannot participate in CNE resulting from limited ability and funds;while senior nurses are mainly restricted by time. It is recommended that hospitals and nursing management in Tibet should solve these problems faced by nurses in participating in CNE by implementing a flexible scheduling system, and providing funding or implementing an incentive system, to enhance the confidence of active nurses in participating in CNE.

In-service Structural Health Monitoring of a Full-scale Composite Horizontal Tail

In-service structural health monitoring（SHM） technologies are critical for the utilization of composite aircraft structures. We developed a Lamb wave-based in-service SHM technology using built-in piezoelectric actuator/sensor networks to monitor delamination extension in a full-scale composite horizontal tail. The in-service SHM technology combine of damage rapid monitoring（DRM） stage and damage imaging diagnosis（DID） stage allows for real-time monitoring and long term tracking of the structural integrity of composite aircraft structures. DRM stage using spearman rank correlation coeffi cient was introduced to generate a damage index which can be used to monitor the trend of damage extension. The DID stage based on canonical correlation analysis aimed at intuitively highlighting structural damage regions in two-dimensional images. The DRM and DID stages were trialed by an in-service SHM experiment of CFRP T-joint. Finally, the detection capability of the in-service SHM technology was verified in the SHM experiment of a full-scale composite horizontal tail. Experimental results show that the rapid monitoring method effectively monitors the damage occurrence and extension tendency in real time; damage imaging diagnosis results are consistent with those from the failure model of the composite horizontal tail structure.

Feasibility of Integrating Leprosy Post-Exposure Prophylaxis with Single-Dose Rifampicin (LPEP) into Routine Leprosy Control Program in Bukedi and Teso Regions in Uganda

Background: World Health Organization recommends the implementation of contact tracing and Leprosy Post Exposure prophylaxis (LPEP) to interrupt the chain of transmission. To accelerate the uptake of this recommendation, a cross-sectional study among contacts of leprosy patients was conducted to investigate the feasibility of integrating leprosy systematic contact tracing and post-exposure prophylaxis (PEP) into the routine leprosy control program. Methods: This was a mixed methods cross-sectional study. The study was implemented in Kumi, Ngora, Serere, Soroti, Budaka and Kibuku Districts. Results: The 45 enrolled index patients (97.8% of the registered) identified a total of 135 contacts, of which 134 (99·2%) consented and were screened. Among them, one new leprosy patient was identified and started on treatment with multidrug therapy (MDT). All the eligible contacts, received the prophylactic treatment with Single Dose Rifampicin (SDR). Overall, SDR was administered to 133(98.5% of the listed contacts) with no adverse event reported. Factors associated with successful contact investigation and management included: Involvement of index patients, health care workers during the contact screening and SDR A administration, counselling of the index patients and contacts by the health care works, LPEP being administered as Directly observed Therapy (DOT) among others. Results Interpretation: The integration of leprosy post-exposure prophylaxis with administration of SDR and contact tracing is feasible, generally accepted by the patient, their contacts and health workers and can be integrated into the National Leprosy control programmes with minimal additional efforts once contact tracing has been established. Therefore, we recommend integration of administration of SDR in to the routine leprosy control program.

Post competency training in standardized training of resident physicians and integrated postgraduates

We focus on the importance and necessity of post-competency-based training in medical education alongside its current challenges and opportunities.Integrating post competency training into standardized educational frameworks is increasingly recognized as a critical component of preparing residents and postgraduates for real-world clinical practice.Post competency training represents a commitment to excellence in medical education,striving to produce competent,skilled practitioners to meet the challenges of modern healthcare.

Spectrum of delayed post-hypoxic leukoencephalopathy syndrome:A systematic review

BACKGROUND Delayed post hypoxic leukoencephalopathy syndrome(DPHLS),also known as Grinker’s myelinopathy,is a rare but significant neurological condition that manifests days to weeks after a hypoxic event.Characterized by delayed onset of neurological and cognitive deficits,DPHLS presents substantial diagnostic and therapeutic challenges.AIM To consolidate current knowledge on pathophysiology,clinical features,diagnostic approaches,and management strategies for DPHLS,providing a comprehensive overview and highlighting gaps for future research.METHODS Following the Preferred Reporting Items for Systematic Reviews and Meta-Analyzes guidelines,we systematically searched PubMed,ScienceDirect and Hinari databases using terms related to delayed post-hypoxic leukoencephalopathy.Inclusion criteria were original research articles,case reports,and case series involving human subjects with detailed clinical,neuroimaging,or pathological data on DPHLS.Data were extracted on study characteristics,participant demographics,clinical features,neuroimaging findings,pathological findings,treatment,and outcomes.The quality assessment was performed using the Joanna Briggs Institute critical appraisal checklist.RESULTS A total of 73 cases were reviewed.Common comorbidities included schizoaffective disorder,bipolar disorder,hypertension,and substance use disorder.The primary causes of hypoxia were benzodiazepine overdose,opioid overdose,polysubstance overdose,and carbon monoxide(CO)poisoning.Symptoms frequently include decreased level of consciousness,psychomotor agitation,cognitive decline,parkinsonism,and encephalopathy.Neuroimaging commonly revealed diffuse T2 hyperintensities in cerebral white matter,sometimes involving the basal ganglia and the globus pallidus.Magnetic resonance spectroscopy often showed decreased N-acetylaspartate,elevated choline,choline-to-creatinine ratio,and normal or elevated lactate.Treatment is often supportive,including amantadine,an antioxidant cocktail,and steroids.Hyperbaric oxygen therapy may be beneficial in those with CO poisoning.Parkinsonism was often treated with levodopa.Most of the patients had substantial recovery over the course of months and many cases had some residual neurocognitive deficits.CONCLUSION DPHLS remains a complex and multifaceted condition with various etiologies and clinical manifestations.Early recognition and appropriate management are crucial to improving patient outcomes.Future research should focus on standardizing diagnostic criteria,using advanced imaging techniques,and exploring therapeutic interventions to improve understanding and treatment of DPHLS.Conducting prospective cohort studies and developing biomarkers for early diagnosis and monitoring will be essential to advance patient care.

Compressive properties of glue-laminated timber circular post modified by basalt fiber reinforced polymer

Glued timber structure is one of the main forms of modern wood architecture,which has gradually developed towards mid-and high-rise buildings.Glue-laminated timber(GLT)is comprised of several laminates of parallel-to-grain dimension lumber that are bonded together with durable,moisture resistant structural adhesives.GLT can be used in horizontal applications as a beam and in vertical applications as a post.So,its compressive performance has a significant impact on structural safety.Fiber reinforced polymers(FRPs)were commonly used to improve the bearing capacity of GLT components,and the structural and process parameters largely determined the reinforcement effect.This study was aimed at investigating the influence of structural and process parameters on the axial compression performance of GLT components.Three wrapping methods(middle-part,end-part and full wrapping)and three lengths(0.6,0.8,and 1.0 m)of wood post specimens were designed in this work and the axial compression performance and ductility of GLT post specimens modified by basalt fiber reinforced polymer(BFRP)were studied.The results showed that the effect of different BFRP wrapping methods on the compressive strength and elastic modulus of laminated wood was not statistically significant(P>0.05).The compressive bearing capacity of unreinforced GLT posts decreased with the increase of aspect ratio.The GLT posts with middle-part and end-part wrapping still followed this pattern,while the compressive bearing capacity of GLT posts with full wrapping showed a pattern of first decreasing and then increasing.For GLT with low aspect ratios(4.0 or 5.3),there was no correlation between the wrapping method and the compressive bearing capacity,while the compressive bearing capacity of GLT with a high aspect ratio(6.7)for middle-part,end-part and full wrapping increased by 3.5%,7.5%and 9.7%,respectively.Compared to the unreinforced group,the ultimate axial compressive strength and modulus of elasticity(MOE)of the 6-E series specimens reinforced at both ends decreased by 2.58%and 6.70%,respectively.The ultimate axial compressive strength of the 8-E specimens reinforced at both ends increased by 8.62%and the MOE decreased by 1.91%.The compressive strength of the 10-E specimens reinforced at both ends increased by 7.51%and the MOE increased by 8.14%.The failure modes of GLT with different aspects were consistent under the same BFRP wrapping,while the failure modes of GLT with the same aspect ratio were different for different BFRP wrapping methods.The ductility performance of GLT with different aspects ratio was improved by the BFRP wrapping.

Postoperative Complications in the General Surgery Department of the Cs Ref of Commune I of the District of Bamako Mali

Postoperative complications represent important indicators for the quality of surgical care. The objectives of this work were to study post-operative complications in the general surgery department of the Cs ref of commune I in Mali, to determine the frequency of post-operative complications, to identify the factors of occurrence, to describe the clinical aspects, diagnostic and therapeutic in order to assess the additional cost linked to post-operative complications. This study was prospective, carried out in the general surgery department on 300 cases of surgical interventions. It covered all patients aged at least 15 years, operated on and hospitalized or not, and who presented complications during the 30 days postoperatively. Patients under the age of 15 were not included (our general surgery department is not a pediatric surgery department). We collected 300 patients among whom 199 (66.33%) were men and 101 (33.66%) women, i.e. a sex ratio = 1.9. The average age was 38 years with extremes of 15 and 87 years. The main initial diagnoses were: acute appendicitis, peritonitis, occlusions, wall hernias, hemorrhoids, uterine prolapse, uterine myomas, ovarian cysts and acute cholecystitis. Emergencies represented 43% (N = 129) of interventions with 6.98% post-operative complications (POC). Postoperative complications were dominated by surgical site infections, 75% of cases (N = 20), wall hemorrhage 5% (N = 1), testicular necrosis 5% (N = 1) and testicular calcification 5% (N = 1), wire rejection 5% (N = 1) and death 5% (N = 1). The management of postoperative complications was surgical in 95% and medical in 100%. Their occurrence extended the hospital stay by 3.65 days and increased the average cost of care by 60541.85 CFA francs. The mortality index lowered by efficient management of complications (IMAGE) calculated in relation to deaths was 95% of cases. Anemia, ASA score ≥ III, Alteimeir II and IV classes, duration of surgery and post-operative hospitalization were factors contributing to post-operative complications.

Non-steroidal anti-inflammatory drugs in postoperative hand fracture management:Do they positively or negatively impact recovery?

This editorial explores the impact of non-steroidal anti-inflammatory drugs(NSAIDs)on postoperative recovery in hand fracture patients,amidst shifting pain management strategies away from opioids due to their adverse effects.With hand fractures being significantly common and postoperative pain management crucial for recovery,the potential of NSAIDs offers a non-addictive pain control alternative.However,the controversy over NSAIDs'effects on bone healing—stemming from their Cyclooxygenase-2 inhibition and associated risks of fracture non-union or delayed union—necessitates further investigation.Despite a comprehensive literature search,the study finds a lack of specific research on NSAIDs in postoperative hand fracture management,highlighting an urgent need for future studies to balance their benefits against possible risks.

Development of a Post Quantum Encryption Key Generation Algorithm Using Electromagnetic Wave Propagation Theory

In today’s rapid widespread of digital technologies into all live aspects to enhance efficiency and productivity on the one hand and on the other hand ensure customer engagement, personal data counterfeiting has become a major concern for businesses and end-users. One solution to ensure data security is encryption, where keys are central. There is therefore a need to find robusts key generation implementation that is effective, inexpensive and non-invasive for protecting and preventing data counterfeiting. In this paper, we use the theory of electromagnetic wave propagation to generate encryption keys.

Advances in Research of Post Embolism Syndrome after Transarterial Chemoembolization(TACE)for Hepatocellular Carcinoma

This article reviews the concept and clinical manifestations of post embolism syndrome after transarterial chemoembolization(TACE),and the prevention or timely intervention of post embolism syndrome in advance is expected to reduce its incidence and degree in clinical treatment,and to improve the quality of treatment of Hepatocellular Carcinoma Carcinoma(HCC).

Comparison of the Clinical Effect of Prefabricated Fiber Post and Plastic Fiber Post in Oral Repair

Objective:To observe and analyze the clinical effect of prefabricated fiber posts and plastic fiber posts in oral repair.Methods:A total of 128 patients admitted to our hospital from January 2023 to June 2024 underwent oral prosthesis treatment,of which the control group(n=64)was treated with prefabricated fiber posts and the observation group(n=64)with plastic fiber posts.The efficacy,retention rate,and complication rate of the two groups were compared.Results:The total effective rate of the observation group was 96.88%,which was significantly higher than that of the control group(84.38%)(P<0.05).The restoration retention rate in the observation group was 95.31%,which was significantly higher than that in the control group(85.94%)(P<0.05).The incidence of postoperative complications in the observation group was 4.69%,which was significantly lower than that in the control group(15.63%)(P<0.05).Conclusion:For patients with oral prostheses,the use of plastic fiber posts for treatment shows better clinical effects,effectively improving the retention rate of the prosthesis and reducing the incidence of complications.Thus,it is worthy of popularization and application.