In-situ electrochemical study on the eff ects of Fe(Ⅲ)on kinetics of pyrite acidic pressure oxidation

Fe(Ⅲ)has been proved to be a more eff ective oxidant than dissolved oxygen at ambient temperature,however,the role of Fe(Ⅲ)in pyrite acidic pressure oxidation was rarely discussed so far.In this paper,in-situ electrochemical investigation was performed using a flow-through autoclave system in acidic pressure oxidation environment.The results illustrated that increasing Fe(Ⅲ)concentrations led to raising in redox potential of the solution,and decreased passivation of pyrite caused by deposition of elemental sulfur.Reduction of Fe(Ⅲ)at pyrite surface was a fast reaction with low activation energy,it was only slightly promoted by rising temperatures.While,the oxidation rate of pyrite at all investigated Fe(Ⅲ)concentrations increased obviously with rising temperatures,the anodic reaction was the rate-limiting step in the overall reaction.Activation energy of pyrite oxidation decreased from 47.74 to 28.79 kJ/mol when Fe(Ⅲ)concentration was increased from 0.05 to 0.50 g/L,showing that the reaction kinetics were limited by the rate of electrochemical reaction at low Fe(Ⅲ)concentrations,while,it gradually turned to be diffusion control with increasing Fe(Ⅲ)concentrations.

Mn-doped SrCoO_(3-δ) Perovskite Oxides for Ethylene Production via Chemical Looping Oxidative Dehydrogenation of Ethane

Chemical looping oxidative dehydrogenation (CL-ODH) is an economically promising method for convertingethane into higher value-added ethylene utilizing lattice oxygen in redox catalysts, also known as oxygen carriers. Inthis study, perovskite-type oxide SrCoO_(3-δ) and B-site Mn ion-doped oxygen carriers (SrCo_(1-x)MnxO_(3-δ), x=0.1, 0.2, 0.3)were prepared and tested for the CL-ODH of ethane. The oxygen-deficient perovskite SrCoO_(3-δ) exhibited high ethyleneselectivity of up to 96.7% due to its unique oxygen vacancies and lattice oxygen migration rates. However, its low ethyleneyield limits its application in the CL-ODH of ethane. Mn doping promoted the reducibility of SrCoO_(3-δ) oxygen carriers,thereby improving ethane conversion and ethylene yield, as demonstrated by characterization and evaluation experiments.X-ray diffraction results confirmed the doping of Mn into the lattice of SrCoO_(3-δ), while X-ray photoelectron spectroscopy(XPS) indicated an increase in lattice oxygen ratio upon incorporation of Mn into the SrCoO_(3-δ) lattice. Additionally, H2temperature-programmed reduction (H2-TPR) tests revealed more peaks at lower temperature reduction zones and a declinein peak positions at higher temperatures. Among the four tested oxygen carriers, SrCo0.8Mn0.2O_(3-δ) exhibited satisfactoryperformance with an ethylene yield of 50% at 710 °C and good stability over 20 redox cycles. The synergistic effect of Mnplays a key role in increasing ethylene yields of SrCoO_(3-δ) oxygen carriers. Accordingly, SrCo0.8Mn0.2O_(3-δ) shows promisingpotential for the efficient production of ethylene from ethane via CL-ODH.

Effects of dietary Clostridium butyricum and rumen protected fat on meat quality,oxidative stability,and chemical composition of finishing goats

Background Clostridium butyricum(CB)is a probiotic that can regulate intestinal microbial composition and improve meat quality.Rumen protected fat(RPF)has been shown to increase the dietary energy density and provide essential fatty acids.However,it is still unknown whether dietary supplementation with CB and RPF exerts beneficial effects on growth performance and nutritional value of goat meat.This study aimed to investigate the effects of dietary CB and RPF supplementation on growth performance,meat quality,oxidative stability,and meat nutritional value of finishing goats.Thirty-two goats(initial body weight,20.5±0.82 kg)were used in a completely randomized block design with a 2 RPF supplementation(0 vs.30 g/d)×2 CB supplementation(0 vs.1.0 g/d)factorial treatment arrangement.The experiment included a 14-d adaptation and 70-d data and sample collection period.The goats were fed a diet consisted of 400 g/kg peanut seedling and 600 g/kg corn-based concentrate(dry matter basis).Result Interaction between CB and RPF was rarely observed on the variables measured,except that shear force was reduced(P<0.05)by adding CB or RPF alone or their combination;the increased intramuscular fat(IMF)content with adding RPF was more pronounced(P<0.05)with CB than without CB addition.The pH24h(P=0.009),a*values(P=0.007),total antioxidant capacity(P=0.050),glutathione peroxidase activities(P=0.006),concentrations of 18:3(P<0.001),20:5(P=0.003)and total polyunsaturated fatty acids(P=0.048)were increased,whereas the L*values(P<0.001),shear force(P=0.050)and malondialdehyde content(P=0.044)were decreased by adding CB.Furthermore,CB supplementation increased essential amino acid(P=0.027),flavor amino acid(P=0.010)and total amino acid contents(P=0.024)as well as upregulated the expression of lipoprotein lipase(P=0.034)and peroxisome proliferator-activated receptorγ(PPARγ)(P=0.012),and downregulated the expression of stearoyl-CoA desaturase(SCD)(P=0.034).The RPF supplementation increased dry matter intake(P=0.005),averaged daily gain(trend,P=0.058),hot carcass weight(P=0.046),backfat thickness(P=0.006),concentrations of 16:0(P<0.001)and c9-18:1(P=0.002),and decreased the shear force(P<0.001),isoleucine(P=0.049)and lysine content(P=0.003)of meat.In addition,the expressions of acetyl-CoA carboxylase(P=0.003),fatty acid synthase(P=0.038),SCD(P<0.001)and PPARγ(P=0.022)were upregulated due to RPF supplementation,resulting in higher(P<0.001)content of IMF.Conclusions CB and RPF could be fed to goats for improving the growth performance,carcass traits and meat quality,and promote fat deposition by upregulating the expression of lipogenic genes of Longissimus thoracis muscle.

Ethane Chemical Looping Oxidative Dehydrogenation to Ethylene over Co_(2)O_(3)(Fe_(2)O_(3),NiO)/LaCoO_(3) Oxygen Carriers

Ethane chemical looping oxidative dehydrogenation(CL-ODH)to ethylene is a new technology for converting ethane to ethylene.In the current study MeO/LaCoO_(3)(MeO=Fe_(2)O_(3),NiO or Co_(2)O_(3))composite metal oxides were prepared via citrate gel and impregnation methods,and used as oxygen carriers for CL-ODH.X-ray diffraction results indicated that all oxygen carriers had a perovskite structure even after eight redox cycles.Under a reaction temperature of 650°C,a reaction pressure of 0.1 MPa,and a weight hourly space velocity(WHSV)of 7500 mL/(g·h),ethane conversion over Co_(2)O_(3)/LaCoO_(3) reached 100%and ethylene selectivity reached 60%,both of which were better than corresponding values attained over Fe_(2)O_(3)/LaCoO_(3) and NiO/LaCoO_(3).Ethylene selectivity remained stable for 80 cycles over Co_(2)O_(3)/LaCoO_(3),then decreased gradually after 80 cycles.X-ray photoelectron spectroscopy results and evaluation results indicated that lattice oxygen and O_(2)2-had a direct relationship with ethane conversion and ethylene selectivity.Co_(2)O_(3)/LaCoO_(3) exhibited a strong capacity to release and absorb oxygen,mainly due to interaction between Co_(2)O_(3) and LaCoO_(3).

NiO-Doped Fe_(2)O_(3)/MgO Properties for the Chemical Looping Oxidative Dehydrogenation of Ethane

Ethane chemical looping oxidative dehydrogenation(CL-ODH)to ethylene is a new technology for ethylene preparation.Fe_(2)O_(3)/MgO oxygen carrier was prepared using the co-precipitation method.The influence of added NiO and its different loadings on Fe_(2)O_(3)/MgO were investigated.Then,a series of oxygen carriers were applied in the CL-ODH of the ethane cycle system.Brunauer-Emmett-Teller(BET),X-ray diffractometry(XRD),X-ray photoelection spectroscopy(XPS),and H2-temperature programmed reduction(TPR)were used to characterize the physicochemical properties of these oxygen carriers.It was confirmed that an interaction between NiO and Fe_(2)O_(3) occurred based on the XPS and H2-TPR results.Based on the CL-ODH activity performance tests conducted in a fixed-bed reactor,it was revealed that ethylene selectivity was significantly improved after NiO addition.Fe_(2)O_(3)-10%NiO/MgO showed the best activity performance with 93%ethane conversion and 50%ethylene selectivity at a reaction temperature of 650℃,atmospheric pressure,and space velocity of 7500 mL/(g·h).

Efficient and stable PtFe alloy catalyst for electrocatalytic methanol oxidation with high resistance to CO

Direct methanol fuel cells(DMFC) are widely considered to be an ideal green energy conversion device but their widespread applications are limited by the high price of the Pt-based catalysts and the instability in terms of surface CO toxicity in long-term operation.Herein,the PtFe alloy nanoparticles(NPs) with small particle size(~4.12 nm) supported on carbon black catalysts with different Pt/Fe atomic ratios(Pt_(1)Fe_(2)/C,Pt_(3)Fe_(4)/C,Pt_(1)Fe_(1)/C,and Pt_(2)Fe_(1)/C) are successfully prepared for enhanced anti-CO poisoning during methanol oxidation reaction(MOR).The optimal atomic ratio of Pt/Fe for the MOR is 1:2,and the mass activity of Pt_(1)Fe_(2)/C(5.40 A mg_(Pt)^(-1)) is 13.5 times higher than that of conventional commercial Pt/C(Pt/C-JM)(0.40 A mg_(Pt)^(-1)).The introduction of Fe into the Pt lattice forms the PtFe alloy phase,and the electron density of Pt is reduced after forming the PtFe alloy.In-situ Fourier transform infrared results indicate that the addition of oxyphilic metal Fe has reduced the adsorption of reactant molecules on Pt during the MOR.The doping of Fe atoms helps to desorb toxic intermediates and regenerate Pt active sites,promoting the cleavage of C-O bonds with good selectivity of CO_(2)(58.1%).Moreover,the Pt_(1)Fe_(2)/C catalyst exhibits higher CO tolerance,methanol electrooxidation activity,and long-term stability than other Pt_(x)Fe_(y)/C catalysts.

In situ Hydrothermal Oxidation of Ternary FeCoNi Alloy Electrode for Overall Water Splitting

Exploring noble metal-free catalyst materials for high efficient electrochemical water splitting to produce hydrogen is strongly desired for renewable energy development.In this article,a novel bifunctional catalytic electrode of insitu-grown type for alkaline water splitting based on FeCoNi alloy substrate has been successfully prepared via a facile one-step hydrothermal oxidation route in an alkaline hydrogen peroxide medium.It shows that the matrix alloy with the atom ratio 4∶3∶3 of Fe∶Co∶Ni can obtain the best catalytic performance when hydrothermally treated at 180℃for 18 h in the solution containing 1.8 M hydrogen peroxide and 3.6 M sodium hydroxide.The as-prepared Fe_(0.4)Co_(0.3)Ni_(0.3)-1.8 electrode exhibits small overpotentials of only 184 and 175 mV at electrolysis current density of 10 mA cm^(-2)for alkaline OER and HER processes,respectively.The overall water splitting at electrolysis current density of 10 mA cm^(-2)can be stably delivered at a low cell voltage of 1.62 V.These characteristics including the large specific surface area,the high surface nickel content,the abundant catalyst species,the balanced distribution between bivalent and trivalent metal ions,and the strong binding of in-situ naturally growed catalytic layer to matrix are responsible for the prominent catalytic performance of the Fe_(0.4)Co_(0.3)Ni_(0.3)-1.8 electrode,which can act as a possible replacement for expensive noble metal-based materials.

One-step electrochemical in-situ Li doping and LiF coating enable ultra-stable cathode for sodium ion batteries

Despite of the higher energy density and inexpensive characteristics,commercialization of layered oxide cathodes for sodium ion batteries(SIBs)is limited due to the lack of structural stability at the high voltage.Herein,the one-step electrochemical in-situ Li doping and LiF coating are successfully achieved to obtain an advanced Na0.79Lix[Li_(0.13)Ni_(0.20)Mn_(0.67)]O_(2)@LiF(NaLi-LNM@LiF)cathode with superlattice structure.The results demonstrate that the Li^(+)doped into the alkali metal layer by electrochemical cycling act as"pillars"in the form of Li-Li dimers to stabilize the layered structure.The supplementation of Li to the superlattice structure inhibits the dissolution of transition metal ions and lattice mismatch.Furthermore,the in-situ LiF coating restrains side reactions,reduces surface cracks,and greatly improves the cycling stability.The electrochemical in-situ modification strategy significantly enhances the electrochemical performance of the half-cell.The NaLi-LNM@LiF exhibits high reversible specific capacity(170.6 m A h g^(-1)at 0.05 C),outstanding capacity retention(92.65%after 200 cycles at 0.5 C)and excellent rate performance(80 mA h g^(-1)at 7 C)in a wide voltage range of 1.5-4.5 V.This novel method of in-situ modification by electrochemical process will provide a guidance for the rational design of cathode materials for SIBs.

Chemical looping oxidative propane dehydrogenation controlled by oxygen bulk diffusion over FeVO_(4)oxygen carrier pellets

The oxygen distribution and evolution within the oxygen carrier exert significant influence on chemical looping processes.This paper describes the influence of oxygen bulk diffusion within FeVO4 oxygen carrier pellets on the chemical looping oxidative propane dehydrogenation(CL-ODH).During CL-ODH,the oxygen concentration at the pellet surface initially decreased and then maintained stable before the final decrease.At the stage with the stable surface oxygen concentration,the reaction showed a stable C3H6 formation rate and high C3H6 selectivity.Therefore,based on Fick’s second law,the oxygen distribution and evolution in the oxygen carrier at this stage were further analyzed.It was found that main reactions of selective oxidation and over-oxidation were controlled by the oxygen bulk diffusion.C3H8 conversion rate kept decreasing during this stage due to the decrease of the oxygen flux caused by the decline of oxygen gradient within the oxygen carrier,while C3H6 selectivity increased due to the decrease of overoxidation.In addition,reaction rates could increase with the propane partial pressure due to the increase of the oxygen gradient within the oxygen carrier until the bulk transfer reached its limit at higher propane partial pressure.This study provides fundamental insights for the diffusion-controlled chemical looping reactions.

In situ chemical oxidation of aniline by persulfate with iron(Ⅱ) activation at ambient temperature

The kinetics of aniline degradation by persulfate processes with iron（Ⅱ） activation at ambient temperature was investigated in this study.With iron（Ⅱ） as initiator,the oxidation reactions were found to follow a biphasic rate phenomenon：a rapid transformation followed by a slow but sustained oxidation process.In the first 30 s,the reaction mainly relies on the persulfate-Fe^（2＋） reaction in which aniline is oxidized rapidly.After 30 s,the aniline was still oxidized but the rate of reaction tended to be slower and the rates were clearly linear-proportional.After the initial fast oxidation,the reactions appeared to follow a pseudo-first-order model.

Chemical oxygen demand reduction in coffee wastewater through chemical flocculation and advanced oxidation processes

The removal of the natural organic matter present in coffee processing wastewater through chemical coagulation-flocculation and advanced oxidation processes （AOP） had been studied. The effectiveness of the removal of natural organic matter using commercial flocculants and UV/H202, UV/O3 and UV/H2O2/O3 processes was determined under acidic conditions. For each of these processes, different operational conditions were explored to optimize the treatment efficiency of the coffee wastewater. Coffee wastewater is characterized by a high chemical oxygen demand （COD） and low total suspended solids. The outcomes of coffee wastewater treatment using coagulation-flocculation and photodegradation processes were assessed in terms of reduction of COD, color, and turbidity. It was found that a reduction in COD of 67% could be realized when the coffee wastewater was treated by chemical coagulation-flocculation with lime and coagulant T-1. When coffee wastewater was treated by coagulation-flocculation in combination with UV/H2O2, a COD reduction of 86% was achieved, although only after prolonged UV irradiation. Of the three advanced oxidation processes considered, UV/H2O2, UV/O3 and UV/H2O2/O3, we found that the treatment with UV/H2O2/O3 was the most effective, with an efficiency of color, turbidity and further COD removal of 87%, when applied to the flocculated coffee wastewater.

Different oxidation routes for lattice oxygen recovery of double-perovskite type oxides LaSrFeCoO6 as oxygen carriers for chemical looping steam methane reforming

Double-perovskite type oxide LaSrFeCoO（LSFCO） was used as oxygen carrier for chemical looping steam methane reforming（CL-SMR） due to its unique structure and reactivity. Two different oxidation routes,steam-oxidation and steam-air-stepwise-oxidation, were applied to investigate the recovery behaviors of the lattice oxygen in the oxygen carrier. The characterizations of the oxide were determined by X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, hydrogen temperature-programmed reduction（H-TPR） and scanning electron microscopy（SEM）. The fresh sample LSFCO exhibits a monocrystalline perovskite structure with cubic symmetry and high crystallinity, except for a little impurity phase due to the antisite defect of Fe/Co disorder. The deconvolution distribution of XPS patterns indicated that Co,and Fe are predominantly in an oxidized state(Feand Fe) and(Coand Co), while O 1s exists at three species of lattice oxygen, chemisorbed oxygen and physical adsorbed oxygen. The double perovskite structure and chemical composition recover to the original state after the steam and air oxidation, while the Co ion cannot incorporate into the double perovskite structure and thus form the CoO just via individual steam oxidation. In comparison to the two different oxidation routes, the sample obtained by steam-oxidation exhibits even higher CHconversion, CO and Hselectivity and stronger hydrogen generation capacity.

Decomposition kinetics of dimethyl methylphospate(chemical agent simulant) by supercritical water oxidation

Supercritical water oxidation （SCWO） has been drawing much attention due to effectively destroy a large variety of high-risk wastes resulting from munitions demilitarization and complex industrial chemical. An important design consideration in the development of supercritical water oxidation is the information of decomposition rate. In this paper, the decomposition rate of dimethyl methylphosphonate（DMMP）, which is similar to the nerve agent VX and GB（Sarin） in its structure, was investigated under SCWO conditions. The experiments were performed in an isothermal tubular reactor with a H2O2 as an oxidant. The reaction temperatures were ranged from 398 to 633℃ at a fixed pressure of 24 MPa. The conversion of DMMP was monitored by analyzing total organic carbon （TOC） on the liquid effluent samples. It is found that the oxidative decomposition of DMMP proceeded rapidly and a high TOC decomposition up to 99.99% was obtained within 11 s at 555℃. On the basis of data derived from experiments, a global kinetic equation for the decomposition of DMMP was developed. The model predictions agreed well with the experimental data.

Treatment of Oil Field Wastewater after Chemical Flooding by Fenton Oxidation Combined with Biodegradation

Wastewater after chemical flooding is difficult to be treated by biological methods due to the residual chemicals in the wastewater. Fenton oxidation, which has been widely applied to detoxifying hazardous organic compounds and improving the biodegradability of these compounds, can solve this problem. So, in this paper, Fenton oxidation was used to enhance the biodegradability of the wastewater after chemical flooding. The op- timum operating conditions for the Fenton oxidation process were 2.5 g/L Fe2 ＋ , 600 mg/L H202 and 30 rain of treatment time. The wastewater pre- treated by Fenton oxidation was treated by aerobic activated sludge. It was found that a small amount of H202 can significantly increase both the biodegradation rate and extent of the wastewater. The effluent CODc, and HPAM contents were 260 and 94 mg/L respectively after the aerobic bio- logical process with the biodegradation time of 24 h. After Fenton oxidation combining with biodegradation, the total CODc, removal efficiency was up to 90%, and polymer and oil degrading efficiencies were 95% and 92% respectively.

Preparation of Anode Material for Lithium Ion Battery by Chemical Oxidation

Anode material for lithium ion battery is prepared by chemical oxidation of natural graphite. After oxidation, the properties of natural graphite are modified, such as surface structure, the content of graphite phases, the number of micropores and its stability. thus the modified natural graphite can be used as anode material for commercial lithium ion battery. The reversible capacity is increased from 100 mAh/g to above 300 mAh/g, and its cycling properly is also satisfactory.

Oxidation Modification of Polyacrylonitrile-Based Carbon Fiber and Its Electro-Chemical Performance as Marine Electrode for Electric Field Test

A novel sensor for ocean electric field testing has been fabricated by polyacrylonitrile-based on carbon fibers with electro-chemical oxidation.The surface profile characteristics of the carbon fibers were characterized by scanning electron microscope,Fourier transform infrared spectra and contact angle.Cyclic voltammetry and Tafel curves have been used to study its electro-chemical performances.Two identical electrodes in sea water as the electric field sensor will swiftly respond to applied electric field which causes positive and negative ions to move in opposite direction,resulting in a electric potential difference(ΔE).Test result indicates that the offset potential is typically below 1 m V with a drift of 60-170μVd^-1.Typical self noise level is 1.07 nV√Hz^(1/2)@1 Hz.The electric field response indicates that the modified electrode pair shows better response to AC sine signal of amplitude and frequency(5 mV and 1 mHz)respectively than its blank.The electric field response model of the modified electrodes is creatively presented according to its electric double layer capacitance and Faraday pseudo-capacitance.Many advantages of the carbon fiber electric field electrode will make it have potential application prospect.

Oxidation mechanisms of C-SiC-TaC-C composites prepared by chemical vapor infiltration

To improve the oxidation-resistance properties,SiC and TaC species were introduced in C/C composites by chemical vapor infiltration(CVI) methods. The oxidation-resistance properties of C-SiC-TaC-C composites were studied by X-Ray diffractometry(XRD),JEOL-6360LV scanning electronic microscopy(SEM) and AdventurerTM electronic balance with precision of 0.1 mg. The results show that,1) the oxidation rate of the composites increases continuously with time at all experimental temperatures;2) The oxidation rate increases with temperature within 700-1 100 ℃,slowly in 700-800 ℃,acutely in 800-1 100 ℃;it reaches a maximum value at 1 100 ℃,then decreases within 1 100-1 400 ℃;3) The relationship curve of oxidation rate with temperature can be divided into three regions. The oxidation rate is controlled by reactivity in region Ⅰ,the mixed effects of reactivity and gas diffusion in region Ⅱ,gas phase diffusion in region Ⅲ;4) The composites exhibit a higher oxidation onset temperature in low temperature region and a lower oxidation rate at high temperature due to the oxidation of TaC to(Ta,O) and the formation of the dense SiO2-Ta2O5 oxide layer respectively. With the addition of SiC/TaC species,the oxidation-resistant properties of C/C composites can be improved effectively.

XPS,Chemical Trapping, and DRFTIR Study on Mechanism of By-Products Formation in Selective (AMM)Oxidation of Propylene on MoO_3 and γ-Bi_2MoO_6

XPS and chemical trapping experments with H2, NH3, and CH3I as trapping agents were carried out for studying the adsorption of propylene over MoO3 or r-Bi2MoO6. The results show that the fragmentation of carbon chain takes place during the adsorption of propylene through breaking C -C double bond and C-C bond on Mo2+ and the adjacent lattice oxygen, leading to formation of the oxygen- or nitrogen-containing by-products of C1 and C2 species. Diffuse-Reflection Fourier Transform Infrared (DRFTIR) Spectroscopy was used to study the surface species formed during the chemisorption and reaction of propylene over y-Bi2MoO6 at a lower temperature. The results that C1, C2 adspecies were detected by DRFTIR at 175℃ are consistent with the results of XPS and chemical trapping experiments, whlle the results at 50℃ Grasselli et al.

Chemical Degradation of Indigo Potassium Tetrasulfonate Dye by Advanced Oxidation Processes

The experimental degradation of a water soluble dye, potassium indigo tetrasulfonate salt, has been studied using stand-alone ozonation and photocatalytic oxidation process. Progress of the dye oxidation was followed by UV-VIS spectrophotometric measurements at controlled operating conditions. The organic content of reaction samples was measured to verify the process efficiency in dye mineralization. According to current results, almost complete color removal was obtained for ozonation within about 1 h reaction time. The reduction of the organic load was almost 80% from its original while initial sulphur content decreased to 32.5%. Dye conversion of 100% was obtained by means of a photocatalytic process using TiO2 as catalyst at 294 nm irradiated UV light. This complete color removal for the catalytic process was observed within 7 min of reaction time. The calculated initial rate of reaction of photocatalysis treatment was 8 times faster than that of ozonolysis. However, the remaining organic load of photocatalysis was almost 88% from its original while the final sulphur content was 27.3%. This contrasting behavior of the performance of the type of oxidation process stressed importance of physicochemical phenomena and intermediates molecules present during dye degradation. An insightful and mechanistic aspect of the dye oxidation was developed by performing quantumchemical calculations.

Advanced Treatment of Biologically Treated Chemical Comprehensive Wastewater by Nano-TiO2 Photocatalytic Oxidation

Nano-TiO2 photocatalytic oxidation was used to perform the advanced treatment of biologically treated chemical comprehensive wastewater. The effects of reaction time,nano-TiO2 dosage and initial p H of the wastewater on the removal rate of COD were tested. The GC/MS and EEM techniques were used to qualitatively analyze organic compounds in the wastewater before and after treatment. The result showed that after the biologically treated chemical comprehensive wastewater was treated by nano-TiO2 photocatalytic oxidation under the conditions of reaction time 3 h,nano-TiO2 dosage 8 g/L,and pH 8. 0,the effluent COD was 61. 9 mg/L and its removal rate was 63. 8%. Additionally,the species of organic pollutants reduced from 12 to 6. Meanwhile,the content of humic-like and fulvic-like substances dropped dramatically.