Research on in-situ condition preserved coring and testing systems

As shallow resources are increasingly depleted,the mechanics'theory and testing technology of deep insitu rock has become urgent.Traditional coring technologies obtain rock samples without retaining the in-situ environmental conditions,leading to distortion of the measured parameters.Herein,a coring and testing systems retaining in-situ geological conditions is presented:the coring system that obtains in-situ rock samples,and the transfer and testing system that stores and analyzes the rocks under a reconstructed environment.The ICP-Coring system mainly consists of the pressure controller,active insulated core reactor and insulation layer and sealing film.The ultimate bearing strength of 100 MPa for pressurepreservation,temperature control accuracy of 0.97%for temperature-retained are realized.CH_(4)and CO permeability of the optimized sealing film are as low as 3.85 and 0.33 ppm/min.The average tensile elongation of the film is 152.4%and the light transmittance is reduced to 0%.Additionally,the pressure and steady-state temperature accuracy for reconstructing the in-situ environment of transfer and storage system up to 1%and±0.2 is achieved.The error recorded of the noncontact sensor ring made of lowdensity polymer is less than 6%than that of the contact test.The system can provide technical support for the deep in-situ rock mechanics research,improving deep resource acquisition capabilities and further clarifying deep-earth processes.

Assessment of rapid impact compaction in ground improvement from in-situ testing

Ground improvement has been used on many construction sites to densify granular materials, in other word, to improve soil properties and reduce potential settlement. This work presents a case study of ground improvement using rapid impact compaction （RIC）. The research site comprises the construction of workshop and depots as part of railway development project at Batu Gajah-Ipoh, Malaysia. In-situ testing results show that the subsurface soil comprises mainly of sand and silty sand through the investigated depth extended to 10 m. Groundwater is approximately 0.5 m below the ground surface. Evaluation of improvement was based on the results of pre- and post-improvement cone penetration test （CPT）. Interpretation software has been used to infer soil properties. Load test was conducted to estimate soil settlement. It is found that the technique succeeds in improving soil properties namely the relative density increases from 45% to 70%, the friction angle of soil is increased by an average of 3°, and the soil settlement is reduced by 50%： The technique succeeds in improving soil properties to approximately 5.0 m in depth depending on soil uniformity with depth.

In-Situ Test on Fatigue Characteristics of Top-Mounted Dividable Pile-Board Subgrade for High-Speed Railway

To simulate the fatigue characteristics of the pile-board structure under long-term dynamic load, using the in-situ dynamic testing system DTS-1, the forced vibration loading was repeated one million times at different cross-sections of the pile-board structure for high-speed railway. The dynamic deformation, permanent deformation and dynamic stress of main reinforcements were measured. The test results show that the dynamic responses of the pile-board structure almost did not vary with the forced vibration times under the simulated trainload. After one million times of forced vibration, the permanent deformations of the midspan section of intermediate span and midspan section of side span were 0.7 mm and 0. 6 mm, respectively, and there was no accumulative plastic deformation at the bearing section of intermediate span.

Research progress and application of deep in-situ condition preserved coring and testing

With the depletion of shallow resources,the exploration of deep earth resources has become a global strategy.The study of the different patterns in the physical mechanical properties of rocks at different occurrence depths is the basis for exploring deep into the earth,with the core and premise being the acquisition and testing of deep in-situ core specimens.Based on the original idea of deep in-situ condition preserved coring(ICP-Coring)and testing,combined with theoretical modeling,numerical analysis,test platform development,indoor testing and engineering application,the principles and technologies of deep ICP-Coring are developed.This principle and technology consists of five parts:in-situ pressurepreserved coring(IPP-Coring),in-situ substance-preserved coring(ISP-Coring),in-situ temperaturepreserved coring(ITP-Coring),in-situ light-preserved coring(ILP-Coring),and in-situ moisturepreserved coring(IMP-Coring).The theory and technology of temperature and pressure reconstruction at different occurrence depths and in different environments are proposed,and prototype trial production was completed by following the principle of displacement and tests based on the in-situ reconstructed environment.The notable advances are as follows:(1)Deep in-situ coring system:A pressure-preserved controller with an ultimate bearing capacity greater than 140 MPa,highperformance(temperature-resistant,pressure-resistant,and low thermally conductive)temperaturepreserved materials,an active temperature control system,and high-barrier quality-preserved membrane materials were developed;a deep ICP-Coring capacity calibration platform was independently developed,a deep in-situ coring technology system was developed,and the acquisition of deep in-situ cores was realized.(2)In-situ storage displacement system:Following the dual-circuit hydraulic design idea,a single-drive source push-pull composite grabbing mechanism was designed;the design of the overall structure for the deep in-situ displacement storage system and ultrahigh pressure cabin structure was completed,which could realize docking the coring device and core displacement in the in-situ reconstructed environment.(3)Test analysis system:A noncontact acoustic-electric-magnetic test system was developed under the in-situ reconstructed environment,and the errors between the test results and traditional contact test results were mostly less than 10%;a detachable deep in-situ core true triaxial test system was developed,which could perform loading tests for deep in-situ cores.The relevant technological achievements were successfully applied to the exploration and development of deep resources,such as deep mines,deep-sea natural gas hydrates,and deep oil and gas.The research results provide technical and equipment support for the construction of a theoretical system for deep in-situ rock mechanics,the development of deep earth resources and energy,and the scientific exploration of different layers and occurrence depths(deep and ultradeep)of the Earth.

Effects of temperature and wavelength choice on in-situ dissolution test of Cimetidine tablets

The effects of temperature and wavelength choice on in-situ dissolution test instrument of Cimetidine were studied. Absorbance （A）〈 1.0 is required when using a fiber-optic dissolution test system. The detection wavelength of 2 （218 nm） was replaced by 244 nm to carry out this test. The absorbance of Cimetidine solution at different temperature showed an obvious change. Calibration of Cimetidine solution should be tested at the same temperature （37° C） with the test solution. A suitable wavelength with smaller tangent slope could be chosen for in-situ dissolution test of Cimetidine tablets.

Characterization of microstructure and strain response in Ti-6Al-4V plasma welding deposited material by combined EBSD and in-situ tensile test

Additive layer manufacturing （ALM） of aerospace grade titanium components shows great promise in supplying a cost-effective alternative to the conventional production routes. Complex microstructures comprised of columnar remnants of directionally solidifiedβ-grains, with interior inhabited by colonies of finerα-plate structures, were found in samples produced by layered plasma welding of Ti-6Al-4V alloy. The application of in-situ tensile tests combined with rapid offline electron backscatter diffraction （EBSD） analysis provides a powerful tool for understanding and drawing qualitative correlations between microstructural features and deformation characteristics. Non-uniform deformation occurs due to a strong variation in strain response between colonies and across columnar grain boundaries. Prismatic and basal slip systems are active, with the prismatic systems contributing to the most severe deformation through coarse and widely spaced slip lines. Certain colonies behave as microstructural units, with easy slip transmission across the entire colony. Other regions exhibit significant deformation mismatch, with local build-up of strain gradients and stress concentration. The segmentation occurs due to the growth morphology and variant constraints imposed by the columnar solidification structures through orientation relationships, interface alignment and preferred growth directions. Tensile tests perpendicular to columnar structures reveal deformation localization at columnar grain boundaries. In this work connections are made between the theoretical macro- and microstructural growth mechanisms and the observed microstructure of the Ti-6Al-4V alloy, which in turn is linked to observations during in-situ tensile tests.

Research of in-situ hydraulic test method by using double packer equipment

Double packer equipment for hydraulic test can be used to measure pressure of test zone directly, and it is frequently used to perform many kinds of hydraulic tests and take groundwater sample from borehole. The test method of this equipment mainly includes the test design, implementation, interpretation and synthetic analysis. By adopting the double packer equipment for hydraulic test, the parameter distribution of rock permeability along borehole can be acquired, as well as the connectivity, water conductivity and water bearing capacity of the disclosed structure and the chemical characteristics of the deep groundwater. It is a necessary method for the research and evaluation of the complex hypotonicity terrace site selection under geological conditions. This method is not only suitable for the geological disposal of high level radioactive waste, but also can be used in the site selection of underground facilities such as storage of petroleum and carbon dioxide. Meanwhile, it has a good application prospect in other hydrogeological investigation fields.

Non-Destructive Imaging of Water Permeation through Cementitious Materials Using MRI

In this study, water permeation through cementitious materials was observed using magnetic resonance imaging (MRI). The influence of cement type on the magnetic resonance signal was studied subsequent to determining the parameters required for imaging. Consequently, adequate imaging of water permeating through hardened cement paste (HCP) made with white Portland cement was achieved, while water permeation through ordinary Portland cement-based HCP yielded poor signal. HCPs maintained at various levels of relative humidity (RH) were observed, and the signal was detected only from those maintained at an RH of higher than 85%. The water permeation depths in HCP were observed by using MRI, and the measured depths were compared to those measured via a spraying water detector on the split surface of the specimens. As a result, good agreement was confirmed between the two methods. Additionally, MRI was applied to concrete specimens;although it was found that water was not detected when a lightweight aggregate was used, water permeation through concrete with limestone aggregate was detectable via MRI. MRI will help in understanding how water permeation causes and accelerates concrete deteriorations such as rebar corrosion and freezing and thawing.

Discussion on bearing capacity of soft rock ground based on in-situ load test

The suitability of five methods was discussed here,taking the typical results from in-situ load test of Renshou Mansion and Caifu Plaza in Yueyang City for example.It shows that bearing capacity can be obtained by the proportion load and limit load from p-s curve with the first and the second point of contraflexure easily.It is recommended that the accurate value of bearing capacity can be obtained by hyperbola fitting method and minimum curvature radius method theoretically.The rebound method is clear in principle,in which the elastoplasticity characteristic is thought about.Out of consideration for the unsteadiness and unobviousness of bearing capacity from relative settlement method,it can be only adopted as reference.So bearing capacity of soft rock ground should be determined by weathering condition of soft rock and curve type.

Study on determination method of in-situ stress using formation fracturing test and Kaiser effect method

A new method, which is based on formation fracturing test and Kaiser effect method, has been developed for confirming the oilfield in-situ stress in this paper. The new method has been used in a certain oilfield of China and the determined oilfield in-situ stresses is more accurate than that based on one single method.

In-situ investigation of deformation behavior and fracture forms of Ti/Al/Mg/Al/Ti laminates

In-situ bending and stretching were conducted on hot-rolled and annealed Ti/Al/Mg/Al/Ti laminates,with a focus on crack initiation and propagation of intermetallics and component layers,which helps to clarify their deformation behavior and fracture forms.The results show that delamination is the early fracture form of laminate with or without intermetallics at Al/Mg interface,so Al/Mg interfacial bonding strength determines the mechanical properties of laminate.Various and irregular intermetallics cracks lead to Al/Mg interface delamination in annealed laminate and help to release stress.Necking and fracture of component layers are observed at the late deformation stage,and the sequence is Al,Mg and Ti layers,resulting from their strength.Angle between crack propagation direction and stretching direction of Mg layer both in rolled and annealed laminates is around 45°due to the effect of shear deformation,and crack convergence leads to final complete fracture of Mg layer.

Test of frequency characteristic for well and itsresponse to seismic waves

The permeation parameters have been calculated by forefathers on the basis of permeation theory by means of the Slug test (Yin, Zheng, 1992) and the restoration curves of well level. We are interested in oscillation of the well level when we make Slug test. Both the permeation parameters and frequency parameters, i.e., natural period and damping coefficients of well aquifer, have been calculated on the basis of vibration theory by means of the oscillation curves. Not only this has given a new method, but also the different response of well level to seismic waves has been explained by it in theory.

Microstructure and mechanical properties of Al-Mg_2Si composite fabricated in-situ by vibrating cooling slope

An innovative semisolid technique termed as vibrating cooling slope(VCS)has been applied to producing in-situ Al-25%Mg2Si(mass fraction)composite.The molten Al-16.5Mg-9.4%Si(mass fraction)alloy with 100°C superheat was poured on the surface of an inclined copper plate(set at 45°inclined angle)while it was vibrated at a frequency of 40 Hz and an amplitude of 400μm.After travelling the length of 40 cm on the slope,the resultant semisolid alloy was cast into a steel mold.For the purpose of comparison,reference composite samples were made by gravity casting(GC)and conventionally still cooling slope casting(CS)methods using the same alloy under identical conditions.The samples were hot extruded at 500°C.It was concluded that the size of Mg2Si particles was decreased by about 50%and 70%for the CS and VCS produced samples respectively when compared to that of the GC produced sample.Despite of their higher porosity contents,both the as-cast and hot-extruded VCS processed samples exhibited higher hardness,shear yield stress(SYS)and ultimate shear strength(USS)values as compared with their GC produced counterparts.These results were attributed to the refined and modified microstructure obtained via this newly developed technique.

In-situ analysis of slip transfer and heterogeneous deformation in tension of Mg-5.4Gd-1.8Y-1.5Zn alloy

Slip transfer is influential in determining damage nucleation of polycrystalline material.The interactions between dislocations and grain boundaries(GBs)was investigated using in-situ tension test in a multi-directionally forged Mg-5.4Gd-1.8Y-1.5Zn(wt%)alloy.It was found that strain accommodation of individual grains by means of slip occurred more easily than slip transfer when several slip systems were operable.The basal-basal slip transfer occurred when the GB misorientation was smaller than 34.2°,whereas basal-pyramidal type took place when the crystallographic misorientation was larger than 48.8°.The product of Luster-Morris m factor and the sum of the Schmid factors of the two correlated slip systems indicated that the threshold for basal-basal slip transfer may exist,however,basal-pyramidal slip transfer shows no such threshold and is more complicated.These results presented here demonstrated that besides the geometrical alignment,the deformation details(such as the number of operable slip systems)and stress state in each individual grain must be considered.

In-situ three-dimensional visualization of dynamic tension deformation in ferrite stainless steels

An improved three-dimensional （3-D） experimental visualization methodology is presented tor evaluating the fracture mechanisms of ferritic stainless steels by in-situ tensile testing with an environmental scanning electron microscope （ESEM）. The samples were machined with a radial notched shape and a sloped surface. Both planar surface deformation and sloping surface deformation-induced microvoids were observed during dynamic tension experiments, where a greater amount of information could be obtained from the sloping surface. The results showed that microvoids formed at the grain boundaries of highly elongated large grains. The microvoids nucleated in the severely deformed regions grew nearly parallel to the tensile axis, predominantly along the grain boundaries. The microvoids nucleated at the interface of particles and the matrix did not propagate due to the high plasticity of the matrix. The large microvoids propagated and showed a zigzag shape along the grain boundaries,seemingly a consequence of the fracture of the slip bands caused by dislocation pile-ups. The final failure took place due to the reduction of the load-beating area.

Design and feasibility analysis of a new completion monitoring technical scheme for natural gas hydrate production tests

As a prerequisite and a guarantee for safe and efficient natural gas hydrates(NGHs)exploitation,it is imperative to effectively determine the mechanical properties of NGHs reservoirs and clarify the law of the change in the mechanical properties with the dissociation of NGHs during NGHs production tests by depressurization.Based on the development of Japan’s two offshore NGHs production tests in vertical wells,this study innovatively proposed a new subsea communication technology-accurate directional connection using a wet-mate connector.This helps to overcome the technical barrier to the communication between the upper and lower completion of offshore wells.Using this new communication technology,this study explored and designed a mechanical monitoring scheme for lower completion(sand screens).This scheme can be used to monitor the tensile stress and radial compressive stress of sand screens caused by NGHs reservoirs in real time,thus promoting the technical development for the rapid assessment and real-time feedback of the in-situ mechanical response of NGHs reservoirs during offshore NGHs production tests by depressurization.

In-situ Horizontal Extrusion Test of Herbaceous Root-Soil with Different Root Types

The influence of different types of roots on the soil is complex and still remains unclear.Four in-situ extrusion tests were conducted on two types of root systems,namely fibrous and tap root system,for three plants,Eleusine indica,Potentilla anserine,and Artemisia argyi,according to the classification in Botany,and the thrust-displacement curves and failure patterns of different samples were analysed by comparison to fill the aforementioned gap.Results reveal that the roots can reduce the characteristics of soil brittleness and enhance its capability to resist large deformation,and different root types contribute different effects to the strain-hardening behavior of the root-soil mass.The contribution of the fibrous root system to strength is limited,whilst the tap root system substantially enhances strength and stiffness.Results of failure patterns show that fibrous and tap root systems affect soil solidification and surface cracking reduction.However,the effect of the tap root system depends on the composition of lateral and tap roots:long and rich lateral roots are effective for resisting the creation of cracks,but thick tap roots with few and thin lateral roots may lead to several surface cracks.

氨甲环酸醇质体的制备及体外评价

目的:制备氨甲环酸醇质体(TA@ES),并初步考察其体外透皮性能。方法:采用乙醇注入-挤出法制备TA@ES。通过单因素考察和Box-Behnken设计-响应面法对处方进行筛选及优化;按最优处方制备TA@ES,对其进行质量评价,并进行体外透皮试验。结果:优化后的TA@ES处方脂药比为3.20∶1,胆固醇用量为0.62%,乙醇用量为19.37%。制得的TA@ES为类球形,平均粒径为(194.3±4.1)nm,Zeta电位为(-32.2±2.6)mV,包封率为(17.20±0.89)%。体外透皮试验结果表明,与氨甲环酸水溶液相比,TA@ES不仅提高了药物经皮渗透量(4.98倍),而且还增加了深层皮肤滞留量(1.74倍)。结论:制备的TA@ES能够提高氨甲环酸的经皮渗透量和深层皮肤滞留量,有望成为黄褐斑治疗药物的新载体。

碎石土路基填料压实及渗透特性

为揭示碎石土路基填料在压实及渗透过程中的颗粒破碎、流失规律,对不同含石量及含水率的碎石土试样进行击实及击实后的渗透试验.结果表明:对于碎石为硬岩、细颗粒为砂类土的碎石土试样,在碎石质量分数(简称含石量)为60%时达到最大干密度;击实破碎前后的粒径分布具有良好的分形特征,分形维数D与干密度呈现正相关,破碎最优分形维数区间粗颗粒为2.23~2.25、细颗粒为2.43~2.45;建立了分形维数D与含石量和含水率的关系式可以对分形维数D进行预测并进一步估计压实效果;破碎率B_(g)与分形维数D也有良好的线性关系,含石量不超过60%时,粗、细颗粒的分形维数D均随颗粒破碎率B_(g)的增加而增加;渗透侵蚀对分形维数D的影响受含石量的影响较大,60%含石量时,分形维数差值随含水率的增大先减小后增大,与渗透系数的变化趋势相同.含石量和含水率是影响颗粒破碎、流失的两个重要因素,但相对于含水率而言,含石量对颗粒破碎、流失的影响更加显著,分形维数D与各配比试样的击实、渗透试验结果的相关性良好,能够较好地反映碎石土试样的压实及渗透特性,可进一步揭示碎石土路基的压实机理,也可为路基工程施工提供参考.

阿戈美拉汀离子液体贴片的制备及体外透皮研究

目的制备阿戈美拉汀离子液体透皮贴片并对其进行质量评价。方法通过药物析晶、体外释放和渗透情况选择处方所用辅料;通过离子交换反应制备阿戈美拉汀-多库酯离子液体,并采用傅里叶变换红外光谱和磁共振波谱对其进行表征;通过溶剂蒸发法制备透皮贴片,对离子液体贴片的含量均匀性、体外释放及体外渗透性能进行质量评价。结果阿戈美拉汀离子液体贴片制备后,表面光滑透明,重量面积比为167 g·m^(-2),单位面积含药量为2.5 mg·cm^(-2);含量均匀度符合药典标准;体外释放速率为(478.31±0.87)μg/(cm^(2)·h^(1/2));体外渗透速率为(24.38±3.93)μg/(cm^(2)·h);24 h的累计透过量为(545.86±93.08)μg·cm^(-2),透过率为(21.78±3.85)%。结论阿戈美拉汀离子液体通过增大贴片的载药量,显著提高贴片的透皮效果,使得透皮贴剂有望成为阿戈美拉汀的新型给药制剂。