In-situ preparation of Cu-BTC modified with organic amines for H_(2)S removal under ambient conditions

Amine modification is an effective strategy to improve the H_(2)S removal performance of Cu-BTC.In order to avoid the problem of pore blockage after amine modification in post synthesis impregnation,herein a series of Cu-BTC modified with organic amine adsorbents were prepared via an in-situ one-pot method and the H_(2)S removal performance under ambient conditions was tested.It is found that the introduced organic amines,depending on the types of amine selected,have a significant influence on the growth of Cu-BTC and its textural properties.The H_(2)S removal performance on the as-prepared materials suggested that the amine modified samples remarkably improved the H_(2)S removal capacities with an order of BA-Cu-BTC>TEA-Cu-BTC>TEOA-Cu-BTC>Cu-BTC.Besides the enlarged surface area and the increased mesopores volumes,BA has the advantages of smaller steric hindrance and-NH_(2)groups,among which the former increased the accessibility of Cu active sites while the latter acted as additional active sites for H_(2)S capturing,thus affording BA-Cu-BTC highest breakthrough capacity of 77.3 mg S/g.Overall,this study elaborates the effect of organic amines in-situ modification on the Cu-BTC structure and desulfurization.

In-situ Preparation of Al/TiAl_3(P) Composite by Direct Reaction between Molten Al and TiO_2 Powder

TiAl3 particle reinforced pure Al composite has been made by direct reaction among molten Al, TiO2 and a flux. The composite exhibits high Synthetically properties. The strength and hardness are higher than those of pure Al matrix by 71.5% and 134% respectively However, the elongation is 20.36%, slightly lower than that of the Al matrix.

In-situ preparation, modulation and mechanism of refractory metal carbide gradient coating

TiC, ZrC and TaC modified layers were in-situ prepared on graphite matrix by chemical vapor infiltration method with metal salts as the activator. Taking the TiC modified layer as an example, through thermodynamic calculation and experiment, the thermal decomposition process of raw materials(Ti/K_(2)TiF_(6)) was analyzed, the formation mechanism of TiC was determined, and the distribution of TiC modified layer was modulated. The results show that activator K_(2)TiF_(6)has higher decomposition temperature than NH4Cl, which is conducive to improving the utilization rate of raw materials in the gas infiltration process. Increasing the content of Ti powder can increase the concentration of reaction gas and contribute to the formation of TiC modified layer. When the molar ratio of Ti to K_(2)TiF_(6)is 3:1, the surface thickness and infiltration depth of Ti C are 5.42 and 136.24 μm, respectively. Increasing the reaction temperature can improve the rate of in-situ reaction and the thickness of TiC surface layer. When the experimental temperature rises to 1600 °C, the TiC surface layer thickness increases to 20.27 μm.

Preparation and applications of calcium ferrite as a functional material:A review

Calcium ferrite(CF)is recognized as a potential green and efficient functional material because of its advantages of magnetism,electrochemistry,catalysis,and biocompatibility in the fields of materials chemistry,environmental engineering,and biomedicine.There-fore,the obtained research results need to be systematically summarized,and new perspectives on CF and its composite materials need to be analyzed.Based on the presented studies of CF and its composite materials,the types and structures of the crystal are summarized.In addition,the current application technologies and theoretical mechanisms with various properties in different fields are elucidated.Moreover,the various preparation methods of CF and its composite materials are elaborated in detail.Most importantly,the advantages and disadvantages of the synthesis methods of CF and its composite materials are discussed,and the existing problems and emerging challenges in practical production are identified.Furthermore,the key future research directions of CF and its composite materials have been prospected from the potential application technologies to provide references for its synthesis and efficient utilization.

Bowel preparation before colonoscopy: Consequences, mechanisms, and treatment of intestinal dysbiosis

The term“gut microbiota”primarily refers to the ecological community of various microorganisms in the gut,which constitutes the largest microbial community in the human body.Although adequate bowel preparation can improve the results of colonoscopy,it may interfere with the gut microbiota.Bowel preparation for colonoscopy can lead to transient changes in the gut microbiota,potentially affecting an individual’s health,especially in vulnerable populations,such as patients with inflammatory bowel disease.However,measures such as oral pro-biotics may ameliorate these adverse effects.We focused on the bowel prepa-ration-induced changes in the gut microbiota and host health status,hypothesized the factors influencing these changes,and attempted to identify measures that may reduce dysbiosis,thereby providing more information for individualized bowel preparation for colonoscopy in the future.

Preparation and wear properties of TiB_2/Al-30Si composites via in-situ melt reactions under high-energy ultrasonic field

TiB2/Al-30Si composites were fabricated via in-situ melt reaction under high-energy ultrasonic field. The microstructure and wear properties of the composite were investigated by XRD, SEM and dry sliding testing. The results indicate that TiB2 reinforcement particles are uniformly distributed in the aluminum matrix under high-energy ultrasonic field. The morphology of the TiB2 particles is in circle-shape or quadrangle-shape, and the size of the particles is 0.1-1.5μm. The primary silicon particles are in quadrangle-shape and the average size of them is about 10μm. Hardness values of the Al-30Si matrix alloy and the TiB2/Al-30Si composites considerably increase as the high energy ultrasonic power increases. In particular, the maximum hardness value of the in-situ composites is about 1.3 times as high as that of the matrix alloy when the ultrasonic power is 1.2 kW, reaching 412 MPa. Meanwhile, the wear resistance of the in-situ TiB2/Al-30Si composites prepared under high-energy ultrasonic field is obviously improved and is insensitive to the applied loads of the dry sliding testing.

Characterization, preparation, and reuse of metallic powders for laser powder bed fusion: a review

Laser powder bed fusion(L-PBF) has attracted significant attention in both the industry and academic fields since its inception, providing unprecedented advantages to fabricate complex-shaped metallic components. The printing quality and performance of L-PBF alloys are infuenced by numerous variables consisting of feedstock powders, manufacturing process,and post-treatment. As the starting materials, metallic powders play a critical role in infuencing the fabrication cost, printing consistency, and properties. Given their deterministic roles, the present review aims to retrospect the recent progress on metallic powders for L-PBF including characterization, preparation, and reuse. The powder characterization mainly serves for printing consistency while powder preparation and reuse are introduced to reduce the fabrication costs.Various powder characterization and preparation methods are presented in the beginning by analyzing the measurement principles, advantages, and limitations. Subsequently, the effect of powder reuse on the powder characteristics and mechanical performance of L-PBF parts is analyzed, focusing on steels, nickel-based superalloys, titanium and titanium alloys, and aluminum alloys. The evolution trends of powders and L-PBF parts vary depending on specific alloy systems, which makes the proposal of a unified reuse protocol infeasible. Finally,perspectives are presented to cater to the increased applications of L-PBF technologies for future investigations. The present state-of-the-art work can pave the way for the broad industrial applications of L-PBF by enhancing printing consistency and reducing the total costs from the perspective of powders.

Microstructural characterization and mechanical properties of(TiC+TiB)/TA15 composites prepared by an in-situ synthesis method

Titanium matrix composites reinforced with ceramic particles are considered a promising engineering material due to their combination of high specific strength,low density,and high modulus.In this study,the TA15-based composites reinforced with a volume fraction of 10% to 25%(TiB+TiC)were prepared using powder metallurgy and casting technique.Microstructural characterization and phase constitution were examined using optical microscopy(OM),scanning electron microscopy(SEM),and X-ray diffraction(XRD).In addition,the microhardness,room temperature(RT)and high temperature(HT)tensile properties of the composites were evaluated.Results revealed that the reinforcements are distributed uniformly even in the composites with a high volume of TiB and TiC.However,as the volume fraction exceeds 15%,TiB and TiC particles become coarsening and exhibit rod-like and dendritic-like morphology.Microhardness increases gradually from 321.2 HV for the base alloy to a maximum of 473.3 HV as the reinforcement increases to 25vol.%.Tensile test results indicate that a reinforcement volume fraction above 20% is beneficial for enhancing tensile strength and yield strength at high temperatures,but it has an adverse effect on room temperature elongation.Conversely,if the reinforcement volume fraction is below 20%,it can improve high-temperature elongation when the temperature exceeds 600℃.

Preparation of an adsorptive membrane of polyvinylidene fluoride incorporated functionalized boron nitride nanosheets for arsenic removal

Incorporating nanomaterials into membranes will enhance wastewater treatment efficiency with their unique characteristics,such as higher permeability,thermal stability,surface roughness,hydrophilicity,and fouling control.In this study,the surface-modified boron nitride with phosphoric acid 2-hydroxyethyl methacrylate ester(PA/BN)was grafted with polyethylene glycol(PEG)via conventional grafting.The PEG grafted PA/BN(PEG-g-PA/BN)melt blended with polyvinylidene fluoride(PVDF)resin by using an internal mixer at different mass percentages 100%PVDF(PVDF),3%PEG-g-PA/BN+97%PVDF(97:3 BN),5%PEG-g-PA/BN+95%PVDF(95:5 BN),7%PEG-g-PA/BN+93%PVDF(93:7 BN),and 7%PEG-g-PA/BNNS+93%PVDF(93:7 BNNS).Phase inversion technique was used to cast the blended mixture into a thin membrane.The prepared membranes were analyzed with different characterization techniques to determine chemical composition,crystallinity,morphology,and thermal properties.The prepared composite membrane was evaluated in terms of water permeability,anti-fouling resistance,and solute rejection efficiency with deionized water,bovine serum albumin,and arsenic solution as well.PVDF membranes show high water flux and porosity.The water flux and porosity of the blends decrease as the percentage of PEG-g-PA/BN increases.However,the highest removal capacity for arsenic was observed at 93:7 BN.The adsorption of arsenic ions takes place via complexation with PA/BN in the PVDF matrix.This was confirmed with field emission scanning electron microscopyeenergy-dispersive X-ray analysis and X-ray photoelectron spectroscopy analyses.

Common Artifacts and Remedies in Histological Preparations

The importance of the accuracy of preparing biological specimen as histological sections that can be examined under a microscope lies in reflecting a true image of the tissue that includes all its components, which are used in scientific research or for the purpose of diagnosing various diseases of the body. Despite this, some cellular structures within the tissue may suffer from some alterations that result from the appearance of defects during any stage of preparing these microscopic sections, which alter or interfere with the precise cellular structures and morphology that constitute the tissue and thus give a different image for tissue features and cause confusion in the work histopathologist in the diagnosis. There are several reasons that can cause a misdiagnosis of the sample that occurs during the surgical separation process or after separation during the stages of microscopic preparation techniques from fixation stage, tissue processing, embedding or microtomy, staining until mounting procedures. The constant need to identify these defects and their causes in addition to try to reduce them is one of the biggest challenges evident in pathology laboratories. Therefore, this study aims to review the most common defects that occur in any stage of tissue processing, with an explanation of their causes and appropriate ways to avoid them.

On-spot preparation of EDTA solution for the treatment of band keratopathy:a case report

Dear Editor,We report a case of band keratopathy who experienced several ocular surgeries,secondary uveitis and glaucoma which eventually led to severe band keratopathy.We use commonly-used vacuum blood collection tubes with ethylenediaminetetraacetic acid dipotassium salt(EDTA-K2)to prepare chelation solution on-spot to remove the calcium deposits on the corneal surface.It is proved to be relatively safety,efficacy,cost-effective.

Preparation and Thermal Stability of AlMoON Based Solar Selective Absorption Coating

AlMoON based solar selective absorption coatings were deposited on stainless steel substrate by magnetron sputtering.The coatings included infrared reflection layer Mo,absorption layer AlMoN,absorption layer AlMoON and antireflection layer AlMoO from bottom to top.The surface of the deposited coatings is flat without obvious defects.The absorptivity and emissivity are 0.896 and 0.09,respectively,and the quality factor is 9.96.After heat treatment at 500℃-36 h,the surface roughness of the coating increases,a small number of cracks and other defects appear,and the broken part is still attached to the coating surface.A certain degree of element diffusion occurs in the coatings,resulting in the decline of the optical properties of the coatings.The absorptivity and emissivity are 0.883 and 0.131,respectively,the quality factor is 7.06,and the PC value is 0.0335.The coatings do not fail under this condition and have certain thermal stability.

Research Progress of Bowel Preparation for Colonoscopy

Colorectal cancer ranks third in the global cancer data in 2020. Colorectal scope is the most effective method to diagnose colorectal diseases such as benign and malignant colorectal tumors. The poor quality of intestinal preparation causes an increased rate of missed diagnosis of colorectal tumors, reduces the rate of cecal intubation for colorectal examination, increases the discomfort, and reduces the compliance of re-examination. Therefore, we should try our best to improve the quality of intestinal preparation. This study reviewed the latest advances related to the preoperative preparation for colonoscopy. Recent research shows that smartphone apps can provide more detailed education and guidance on bowel preparation;Pre-packaged foods are more suitable as a way to eat before colonoscopy. The use of smaller doses, better taste of cathartic agents, and some auxiliary measures, combined with the patient’s situation to provide personalized intestinal preparation measures to improve the quality of intestinal preparation. Starting from the quality of colonoscopy bowel preparation, continuous improvement of patients’ tolerance to bowel preparation, continuous improvement of bowel preparation plan based on individual factors’ needs, and better communication with examined subjects by using existing scientific information technology, may be the hot spot of colonoscopy bowel preparation research in the next few years.

Progress in preparation of AlN-reinforced magnesium matrix composites:A review

As a ceramic material,AlN has very good thermophysical and mechanical properties.In addition,AlN is an effective refining agent for Mg alloys because it has a lattice constant similar to that of Mg.Therefore,AlN is an ideal reinforcement for magnesium matrix composites(MMCs),and is attracting increasing attention.This review addresses the development of preparation technologies for AlN-reinforced Mg matrix composites.The mainstream preparation techniques include stir casting,melt infiltration,powder metallurgy,and in-situ methods.In addition,the advantages and disadvantages of these techniques are analyzed in depth,and it is pointed out that the next direction for the preparation of high-performance AlN-reinforced MMCs is less aluminization and multiple technologies integration.

Preparation of single atom catalysts for high sensitive gas sensing

Single atom catalysts(SACs)have garnered significant attention in the field of catalysis over the past decade due to their exceptional atom utilization efficiency and distinct physical and chemical properties.For the semiconductor-based electrical gas sensor,the core is the catalysis process of target gas molecules on the sensitive materials.In this context,the SACs offer great potential for highly sensitive and selective gas sensing,however,only some of the bubbles come to the surface.To facilitate practical applications,we present a comprehensive review of the preparation strategies for SACs,with a focus on overcoming the challenges of aggregation and low loading.Extensive research efforts have been devoted to investigating the gas sensing mechanism,exploring sensitive materials,optimizing device structures,and refining signal post-processing techniques.Finally,the challenges and future perspectives on the SACs based gas sensing are presented.

The preparation and properties of N-doped carbon materials and their use for sodium storage

Defect engineering by heteroatom doping gives carbon materials some new characteristics such as a different electronic structure and a high electrochemical activity,making them suitable for high-performance applications.N-doping has been widely investigated because of its similar atom radius to carbon,high electronegativity as well as many different configurations.We summarize the preparation methods and properties of N-doped carbon materials,and discuss their possible use in sodium ion storage.The relationships between N content/configuration and crystallinity,electronic conductivity,wettability,chemical reactivity as well as sodium ion storage performance are discussed.

Insight into demand-driven preparation of single-atomic mediators for lithium–sulfur batteries

Lithium-sulfur(Li-S) batteries have attracted considerable attention as one of the most appealing energy storage systems.Strenuous efforts have been devoted to tackling the tremendous challenges,mainly pertaining to the severe shuttle effect,sluggish redox kinetics and lithium dendritic growth.Single-atomic mediators as promising candidates exhibit impressive performance in addressing these intractable issues.Related research often utilizes a trial-and-error approach,proposing solutions to fabricate single-atomic materials with diversified features.However,comprehensive review articles especially targeting demand-driven preparation are still in a nascent stage.Inspired by these considerations,this review summarizes the design of single-atomic mediators based on the application case-studies in LiS batteries and other metal-sulfur systems.Emerging preparation routes represented by chemical vapor deposition technology are introduced in a demand-oriented classification.Finally,future research directions are proposed to foster the advancement of single-atomic mediators in Li-S realm.

Novel wood-plastic composite fabricated via modified steel slag:Preparation,mechanical and flammability properties

A novel method was developed to enhance the utilization rate of steel slag(SS).Through treatment of SS with phosphoric acid and aminopropyl triethoxysilane(KH550),we obtained modified SS(MSS),which was used to prepare MSS/wood-plastic composites(MSS/WPCs)by replacing talcum powder(TP).The composites were fabricated through melting blending and hot pressing.Their mechanical and combustion properties,which comprise heat release,smoke release,and thermal stability,were systematically investigated.MSS can improve the mechanical strength of the composites through grafting reactions between wood powder and thermoplastics.Notably,MSS/WPC#50(16wt%MSS)with an MSS-to-TP mass ratio of 1:1 exhibited optimal comprehensive performance.Compared with those of WPC#0 without MSS,the tensile,flexural,and impact strengths of MSS/WPC#50 were increased by 18.5%,12.8%,and 18.0%,respectively.Moreover,the MSS/WPC#50 sample achieved the highest limited oxygen index of 22.5%,the highest vertical burning rating at the V-1 level,and the lowest horizontal burning rate at 44.2 mm/min.The formation of a dense and stable char layer led to improved thermal stability and a considerable reduction in heat and smoke releases of MSS/WPC#50.However,the partial replacement of TP with MSS slightly compromised the mechanical and flame-retardant properties,possibly due to the weak grafting caused by SS powder agglomeration.These findings suggest the suitability of MSS/WPCs for high-value-added applications as decorative panels indoors or outdoors.

Effects of site preparation methods on soil physical properties and outplanting success of coniferous seedlings in boreal forests

This study assessed the effect of patch scarification and mounding on the physical properties of the root layer and the success of tree planting in various types of forests.This study was conducted on 12 forest sites in taiga forests of the European part of Russia.A total of 54 plots were set up to assess seedling survival;root collar diameter,height,and heigh increment were measured for 240 seedlings to assess growth.In the rooting layer,240 soil samples were taken to determine physical properties.The study showed that soil treatment methods had no effect on bulk density and total porosity in Cladina sites.However,reduced soil moisture was noted,particularly in mounds,resulting in increased aeration.In Myrtillus sites,there were increased bulk density,reduced soil moisture,and total porosity in the mounds.Mounding treatment in Polytrichum sites resulted in reduced soil moisture and increased aeration porosity.In the Myrtillus and Polytrichum sites,patch scarification had no effects on physical properties.In Polytrichum sites,survival rates,heights,and heigh increments of bareroot Norway spruce seedlings in mounds were higher than in patches;however,the same did not apply to diameter.In Cladina and Myrtillus sites,there was no difference in growth for bareroot and containerised seedlings with different soil treatments.Growing conditions and soil types should be considered when applying different soil treatment methods to ensure high survival rates and successful seedling growth.

Preparation of Phenolic Resin/Silver Nanocomposites via in-situ Reduction

Resol type phenolic resin/silver nanocomposite was prepared by in-situ reduction method, in which the curing of phenolic resin and the formation of silver nano-particles took place simultaneously. The silver ions were reduced completely to silver nanoparticles, which were dispersed homogeneously in the resin matrix with narrow size distribution.