In-situ stabilisation followed by ex-situ composting for treatment and disposal of heavy metals polluted sediments

An innovative in-situ stabilisation treatment followed by ex-situ sediment composting was tested for its ability to treat and dispose of heavy-metal-polluted sediments in a river near the Chinese Pearl Delta. First, polluted sediments were treated in-situ to stabilise the heavy metals. Then the treated sediments were dredged, dewatered and sent for high temperature aerobic composting （HTAC） treatment. Finally, the compost products were used as a fertiliser for fiver bank plants. The stabilisation efficiency of heavy metals during the process was investigated and the results are as follows： （1） using in-situ stabilisation, the extraction concentrations of Cu, Zn and Pb were reduced by 65.0%, 82.2% and 90.0%, respectively, which are much lower than the national standard given in the Identification Standard for Hazardous Waste （GB5085.3-1996）; （2） chemical fraction analysis showed that heavy metals were further stabilized during the HTAC treatment; （3） the concentrations of Cu, Zn and Pb in rainwater leachate through the river bank met the level of class V in the Environmental Quality Standards for Surface Water in China （GB3838-2002）. Therefore, using this new process, the toxicities of heavy metals in sediments were reduced markedly.

Assessing the conservation impact of Chinese indigenous chicken populations between ex-situ and in-situ using genome-wide SNPs

Conservation programs require rigorous evaluation to ensure the preservation of genetic diversity and viability of conservation populations. In this study, we conducted a comparative analysis of two indigenous Chinese chicken breeds, Gushi and Xichuan black-bone, using whole-genome SNPs to understand their genetic diversity, track changes over time and population structure. The breeds were divided into five conservation populations(GS1, 2010, ex-situ;GS2, 2019, ex-situ;GS3, 2019, in-situ;XB1, 2010, in-situ;and XB2, 2019, in-situ) based on conservation methods and generations. The genetic diversity indices of three conservation populations of Gushi chicken showed consistent trends, with the GS3 population under in-situ strategy having the highest diversity and GS2 under ex-situ strategy having the lowest. The degree of inbreeding of GS2 was higher than that of GS1 and GS3. Conserved populations of Xichuan black-bone chicken showed no obvious changes in genetic diversity between XB1 and XB2. In terms of population structure, the GS3 population were stratified relative to GS1 and GS2. According to the conservation priority, GS3 had the highest contribution to the total gene and allelic diversity in GS breed, whereas the contribution of XB1 and XB2 were similar. We also observed that the genetic diversity of GS2 was lower than GS3, which were from the same generation but under different conservation programs(in-situ and ex-situ). While XB1 and XB2 had similar levels of genetic diversity. Overall, our findings suggested that the conservation programs performed in ex-situ could slow down the occurrence of inbreeding events, but could not entirely prevent the loss of genetic diversity when the conserved population size was small, while in-situ conservation populations with large population size could maintain a relative high level of genetic diversity.

In-situ AFM and quasi-in-situ studies for localized corrosion in Mg-9Al-1Fe-(Gd) alloys under 3.5 wt.% NaCl environment

Revealing the localized corrosion process of Mg alloy is considered as one of the most significant ways for improving its corrosion resistance.The reliable monitor should be high distinguishability and real-time in liquid environment.Herein,Mg-9Al-1Fe and Mg-9Al-1Fe-1Gd alloys were designed to highlight the impact of intermetallic on the corrosion behaviour.In-situ AFM with a special electrolyte circulation system and quasi-in-situ SEM observation were used to monitor the corrosion process of the designed alloys.SEM-EDS and TEM-SAED were applied to identify the intermetallic in the designed alloys,and their volta potentials were measured by SKPFM.According to the real-time and real-space in-situ AFM monitor,the corrosion process consisted of dissolution of anodicα-Mg phase,accumulation of corrosion products around cathodic phase and shedding of some fine cathodic phase.Then,the localized corrosion process of Mg alloy was revealed combined with the results of the monitor of corrosion process and Volta potential difference.

An in-situ study of static recrystallization in Mg using high temperature EBSD

It has been a common method to improve the mechanical properties of metals by manipulating their microstructures via static recrystallization,i.e.,through heat treatment.Therefore,the knowledge of recrystallization and grain growth is critical to the success of the technique.In the present work,by using in-situ high temperature EBSD,the mechanisms that control recrystallization and grain growth of an extruded pure Mg were studied.The experimental results revealed that the grains of priority for dynamic recrystallization exhibit fading competitiveness under static recrystallization.It is also found that grain boundary movement or grain growth is likely to show an inverse energy gradient effect,i.e.,low energy grains tend to swallow or grow into high energy grains,and grain boundaries of close to 30°exhibit superior growth advantage to others.Another finding is that{10-12}tensile twin boundaries are sites of hardly observed for recrystallization,and are finally swallowed by adjacent recrystallized grains.The above findings may give comprehensive insights of static recrystallization and grain growth of Mg,and may guide the design of advanced materials processing in microstructural engineering.

A continuous and long-term in-situ stress measuring method based on fiber optic. Part I: Theory of inverse differential strain analysis

A method for in-situ stress measurement via fiber optics was proposed. The method utilizes the relationship between rock mass elastic parameters and in-situ stress. The approach offers the advantage of long-term stress measurements with high spatial resolution and frequency, significantly enhancing the ability to measure in-situ stress. The sensing casing, spirally wrapped with fiber optic, is cemented into the formation to establish a formation sensing nerve. Injecting fluid into the casing generates strain disturbance, establishing the relationship between rock mass properties and treatment pressure.Moreover, an optimization algorithm is established to invert the elastic parameters of formation via fiber optic strains. In the first part of this paper series, we established the theoretical basis for the inverse differential strain analysis method for in-situ stress measurement, which was subsequently verified using an analytical model. This paper is the fundamental basis for the inverse differential strain analysis method.

An in-situ self-etching enabled high-power electrode for aqueous zinc-ion batteries

Sluggish storage kinetics is considered as the main bottleneck of cathode materials for fast-charging aqueous zinc-ion batteries(AZIBs).In this report,we propose a novel in-situ self-etching strategy to unlock the Palm tree-like vanadium oxide/carbon nanofiber membrane(P-VO/C)as a robust freestanding electrode.Comprehensive investigations including the finite element simulation,in-situ X-ray diffraction,and in-situ electrochemical impedance spectroscopy disclosed it an electrochemically induced phase transformation mechanism from VO to layered Zn_(x)V_(2)O_5·nH_(2)O,as well as superior storage kinetics with ultrahigh pseudocapacitive contribution.As demonstrated,such electrode can remain a specific capacity of 285 mA h g^(-1)after 100 cycles at 1 A g^(-1),144.4 mA h g^(-1)after 1500 cycles at 30 A g^(-1),and even 97 mA h g^(-1)after 3000 cycles at 60 A g^(-1),respectively.Unexpectedly,an impressive power density of 78.9 kW kg^(-1)at the super-high current density of 100 A g^(-1)also can be achieved.Such design concept of in-situ self-etching free-standing electrode can provide a brand-new insight into extending the pseudocapacitive storage limit,so as to promote the development of high-power energy storage devices including but not limited to AZIBs.

Microstructural characterization and mechanical properties of(TiC+TiB)/TA15 composites prepared by an in-situ synthesis method

Titanium matrix composites reinforced with ceramic particles are considered a promising engineering material due to their combination of high specific strength,low density,and high modulus.In this study,the TA15-based composites reinforced with a volume fraction of 10% to 25%(TiB+TiC)were prepared using powder metallurgy and casting technique.Microstructural characterization and phase constitution were examined using optical microscopy(OM),scanning electron microscopy(SEM),and X-ray diffraction(XRD).In addition,the microhardness,room temperature(RT)and high temperature(HT)tensile properties of the composites were evaluated.Results revealed that the reinforcements are distributed uniformly even in the composites with a high volume of TiB and TiC.However,as the volume fraction exceeds 15%,TiB and TiC particles become coarsening and exhibit rod-like and dendritic-like morphology.Microhardness increases gradually from 321.2 HV for the base alloy to a maximum of 473.3 HV as the reinforcement increases to 25vol.%.Tensile test results indicate that a reinforcement volume fraction above 20% is beneficial for enhancing tensile strength and yield strength at high temperatures,but it has an adverse effect on room temperature elongation.Conversely,if the reinforcement volume fraction is below 20%,it can improve high-temperature elongation when the temperature exceeds 600℃.

Development review and the prospect of oil shale in-situ catalysis conversion technology

As an unconventional resource, oil shale possesses abundant reserves and significant potential for industrial applications. The rational and efficient development of oil shale resources holds immense importance in reducing national energy demand. In-situ catalytic technology, characterized by its high efficiency, low pollution, and minimal energy consumption, represents a key direction for future oil shale development. This paper provides a comprehensive review of research progress in in-situ oil shale mining technology, oil shale pyrolysis catalysts, the pyrolysis mechanism of kerogen, and the compatibility of different heating processes and catalysts. Furthermore, the paper proposes future research directions and prospects for oil shale in-situ catalytic technology, including reservoir modification, highefficiency catalyst synthesis, injection processes, and high-efficiency heating technology. These insights serve as valuable technical references for the advancement of oil shale in-situ catalytic technology.

Progress in in-situ electrochemical nuclear magnetic resonance for battery research

A thorough understanding of the fundamental electrochemical and chemical processes in batteries is crucial to advancing energy density and power density.However,the characterizations of such processes are complex.In-situ electrochemical nuclear magnetic resonance(EC-NMR)offers the capability to collect real-time data during battery operation,furnishing insights into the local structures and ionic dynamics of materials by monitoring changes in the chemical environment around the nuclei.EC-NMR also has the advantages of being both quantitative and non-destructive.This paper systematically reviews the design of EC-NMR approach,and delves into the applications and progress of EC-NMR concerning battery reaction mechanisms,failure mechanisms,and overall battery systems.The review culminates in a comprehensive summary of the perspective and challenges associated with EC-NMR.

In-situ polymerized PEO-based solid electrolytes contribute better Li metal batteries:Challenges,strategies,and perspectives

Polyethylene oxide(PEO)-based solid polymer electrolytes(SPEs)with good electrochemical stability and excellent Li salt solubility are considered as one of the most promising SPEs for solid-state lithium metal batteries(SSLMBs).However,PEO-based SPEs suffer from low ionic conductivity at room temperature and high interfacial resistance with the electrodes due to poor interfacial contact,seriously hindering their practical applications.As an emerging technology,in-situ polymerization process has been widely used in PEO-based SPEs because it can effectively increase Li-ion transport at the interface and improve the interfacial contact between the electrolyte and electrodes.Herein,we review recent advances in design and fabrication of in-situ polymerized PEO-based SPEs to realize enhanced performance in LMBs.The merits and current challenges of various SPEs,as well as their stabilizing strategies are presented.Furthermore,various in-situ polymerization methods(such as free radical polymerization,cationic polymerization,anionic polymerization)for the preparation of PEO-based SPEs are summarized.In addition,the application of in-situ polymerization technology in PEO-based SPEs for adjustment of the functional units and addition of different functional filler materials was systematically discussed to explore the design concepts,methods and working mechanisms.Finally,the challenges and future prospects of in-situ polymerized PEO-based SPEs for SSLMBs are also proposed.

In-situ interfacial passivation and self-adaptability synergistically stabilizing all-solid-state lithium metal batteries

The function of solid electrolytes and the composition of solid electrolyte interphase(SEI)are highly significant for inhibiting the growth of Li dendrites.Herein,we report an in-situ interfacial passivation combined with self-adaptability strategy to reinforce Li_(0.33)La_(0.557)TiO_(3)(LLTO)-based solid-state batteries.Specifically,a functional SEI enriched with LiF/Li_(3)PO_(4) is formed by in-situ electrochemical conversion,which is greatly beneficial to improving interface compatibility and enhancing ion transport.While the polarized dielectric BaTiO_(3)-polyamic acid(BTO-PAA,BP)film greatly improves the Li-ion transport kinetics and homogenizes the Li deposition.As expected,the resulting electrolyte offers considerable ionic conductivity at room temperature(4.3 x 10~(-4)S cm^(-1))and appreciable electrochemical decomposition voltage(5.23 V)after electrochemical passivation.For Li-LiFePO_(4) batteries,it shows a high specific capacity of 153 mA h g^(-1)at 0.2C after 100 cycles and a long-term durability of 115 mA h g^(-1)at 1.0 C after 800 cycles.Additionally,a stable Li plating/stripping can be achieved for more than 900 h at 0.5 mA cm^(-2).The stabilization mechanisms are elucidated by ex-situ XRD,ex-situ XPS,and ex-situ FTIR techniques,and the corresponding results reveal that the interfacial passivation combined with polarization effect is an effective strategy for improving the electrochemical performance.The present study provides a deeper insight into the dynamic adjustment of electrode-electrolyte interfacial for solid-state lithium batteries.

Interplay of laser power and pore characteristics in selective laser melting of ZK60 magnesium alloys:A study based on in-situ monitoring and image analysis

This study offers significant insights into the multi-physics phenomena of the SLM process and the subsequent porosity characteristics of ZK60 Magnesium(Mg)alloys.High-speed in-situ monitoring was employed to visualise process signals in real-time,elucidating the dynamics of melt pools and vapour plumes under varying laser power conditions specifically between 40 W and 60 W.Detailed morphological analysis was performed using Scanning-Electron Microscopy(SEM),demonstrating a critical correlation between laser power and pore formation.Lower laser power led to increased pore coverage,whereas a denser structure was observed at higher laser power.This laser power influence on porosity was further confirmed via Optical Microscopy(OM)conducted on both top and cross-sectional surfaces of the samples.An increase in laser power resulted in a decrease in pore coverage and pore size,potentially leading to a denser printed part of Mg alloy.X-ray Computed Tomography(XCT)augmented these findings by providing a 3D volumetric representation of the sample internal structure,revealing an inverse relationship between laser power and overall pore volume.Lower laser power appeared to favour the formation of interconnected pores,while a reduction in interconnected pores and an increase in isolated pores were observed at higher power.The interplay between melt pool size,vapour plume effects,and laser power was found to significantly influence the resulting porosity,indicating a need for effective management of these factors to optimise the SLM process of Mg alloys.

Oxidation of emerging organic contaminants by in-situ H_(2)O_(2) fenton system

The existence and risk of emerging organic contaminants(EOCs)have been under consideration and paid much effort to degrade these pollutants.Fenton system is one of the most widely used technologies to solve this problem.The original Fenton system relies on the hydroxyl radicals produced by Fe(Ⅱ)/H_(2)O_(2) to oxidize the organic contaminants.However,the application of the Fenton system is limited by its low iron cycling efficiency and the high risks of hydrogen peroxide transportation and storage.The introduction of external energy(including light and electricity etc.)can effectively promote the Fe(Ⅲ)/Fe(Ⅱ)cycle and the reduction of oxygen to produce hydrogen peroxide in situ.This review introduces three in-situ Fenton systems,which are electro-Fenton,Photo-Fenton,and chemical reaction.The mechanism,influencing factors,and catalysts of these three in-situ Fenton systems in degrading EOCs are discussed systematically.This review strengthens the understanding of Fenton and in-situ Fenton systems in degradation,offering further insight into the real application of the in-situ Fenton system in the removal of EOCs.

In-situ coating and surface partial protonation co-promoting performance of single-crystal nickel-rich cathode in all-solid-state batteries

The poor electrochemical performance of all-solid-state batteries(ASSBs),which is assemblied by Ni-rich cathode and poly(ethylene oxide)(PEO)-based electrolytes,can be attributed to unstable cathodic interface and poor crystal structure stability of Ni-rich cathode.Several coating strategies are previously employed to enhance the stability of the cathodic interface and crystal structure for Ni-rich cathode.However,these methods can hardly achieve simplicity and high efficiency simultaneously.In this work,polyacrylic acid(PAA)replaced traditional PVDF as a binder for cathode,which can achieve a uniform PAA-Li(LixPAA(0<x≤1))coating layer on the surface of single-crystal LiNi_(0.83)Co_(0.12)Mn_(0.05)O_(2)(SC-NCM83)due to H^(+)/Li^(+)exchange reaction during the initial charging-discharging process.The formation of PAA-Li coating layer on cathode can promote interfacial Li^(+)transport and enhance the stability of the cathodic interface.Furthermore,the partially-protonated surface of SC-NCM83 casued by H^(+)/Li^(+)exchange reaction can restrict Ni ions transport to enhance the crystal structure stability.The proposed SC-NCM83-PAA exhibits superior cycling performance with a retention of 92%compared with that(57.3%)of SC-NCM83-polyvinylidene difluoride(PVDF)after 200 cycles.This work provides a practical strategy to construct high-performance cathodes for ASSBs.

Emerging trends in expansive soil stabilisation: A review

Expansive soils are problematic due to the performances of their clay mineral constituent, which makes them exhibit the shrink-swell characteristics. The shrink-swell behaviours make expansive soils inappropriate for direct engineering application in their natural form. In an attempt to make them more feasible for construction purposes, numerous materials and techniques have been used to stabilise the soil. In this study, the additives and techniques applied for stabilising expansive soils will be focused on,with respect to their efficiency in improving the engineering properties of the soils. Then we discussed the microstructural interaction, chemical process, economic implication, nanotechnology application, as well as waste reuse and sustainability. Some issues regarding the effective application of the emerging trends in expansive soil stabilisation were presented with three categories, namely geoenvironmental,standardisation and optimisation issues. Techniques like predictive modelling and exploring methods such as reliability-based design optimisation, response surface methodology, dimensional analysis, and artificial intelligence technology were also proposed in order to ensure that expansive soil stabilisation is efficient.

Laboratory-scale model of carbon dioxide deposition for soilstabilisation

Olivine sand is a natural mineral,which,when added to soil,can improve the soil’s mechanical properties while also sequester carbon dioxide(CO2)from the surrounding environment.The originality of this paper stems from the novel two-stage approach.In the first stage,natural carbonation of olivine and carbonation of olivine treated soil under different CO2pressures and times were investigated.In this stage,the unconfined compression test was used as a tool to evaluate the strength performance.In the second stage,details of the installation and performance of carbonated olivine columns using a laboratory-scale model were investigated.In this respect,olivine was mixed with the natural soil using the auger and the columns were then carbonated with gaseous CO2.The unconfined compressive strengths of soil in the first stage increased by up to 120% compared to those of the natural untreated soil.The strength development was found to be proportional to the CO2pressure and carbonation period.Microstructural analyses indicated the presence of magnesite on the surface of carbonated olivinetreated soil,demonstrating that modified physical properties provided a stronger and stiffer matrix.The performance of the carbonated olivine-soil columns,in terms of ultimate bearing capacity,showed that the carbonation procedure occurred rapidly and yielded a bearing capacity value of 120 k Pa.Results of this study are of significance to the construction industry as the feasibility of carbonated olivine for strengthening and stabilizing soil is validated.Its applicability lies in a range of different geotechnical applications whilst also mitigates the global warming through the sequestration of CO2.

Performance Evaluation of Waste Stabilisation Ponds

Waste stabilisation pond system has been used more especially in developing countries for sewage treatment. The objective of this study was to investigate the hydraulic and performance efficiency of Palapye waste stabilisation ponds. The hydraulic efficiency was evaluated through drogue, pond geometry and sludge accumulation assessment. The performance efficiency was evaluated through periodic sampling and analysis of physiochemical and bacteriological parameters of individual units and of the system as a whole. Except for the maturation ponds, the depth of the anaerobic pond had reduced from 4 m to 0.45 m, for facultative ponds from 2.0 m to a range of 0.52 m - 0.91 m. The design hydraulic retention time of the system had reduced from 20 days to 7.1 days. The concentration of some physiochemical parameters in the effluent was 305 mg·L-1, 277 Nephelometric Turbidity Units (NTU), 204 mg·L-1, 156 mg·L-1, 110 mg·L-1, and 15 mg·L-1 being total suspended solids, turbidity, nitrates, chemical oxygen demand, biochemical oxygen demand and phosphate respectively. These values were more than the standard limits of the country. Effluent total coliforms concentration was 3.6 log units and within the threshold of 4.3 log units, faecal coliforms concentration was 3.5 log units, slightly higher than the threshold of 3 log units. Though Escherichia coli have no limits for discharge into other environments, the concentration in the effluent was reasonable at 2.5 log units and also within irrigation limit of 3 log counts. Palapye wastewater treatment system hydraulic efficiency is lower than the design criterion. The system was overall poor in physiochemical parameters removal but better in bacteriological removal.

Stabilisation of Pb in Pb Smelting Slag-Contaminated Soil by Compost-Modified Biochars and Their Effects on Maize Plant Growth

Compost has been used to stabilise lead (Pb) in soil. However, compost contains a high level of dissolved organic matter (DOM) which may make Pb bioavailable in plant and thereby limiting its effectiveness and application. Addition of biochar to compost can reduce this effect. Rice husk (RH) and Cashew nut shell (CNS) biochars and compost-modified biochars were used in comparison to compost for stabilizing Pb in lead smelting slag (LSS)-contaminated soil (Pb = 18,300 mg/kg) in Nigeria. Efficiency of Pb stabilisation in control and amended soils was assessed using CaCl2 batch leaching experiment and plant performance. In pot experiments, maize plant was grown on the contaminated soil and on soil treated with minimum and optimum doses of the amendments singly and in combination for 6 weeks. Agronomical and chemical parameters of the plants were measured. CaCl2-extractable Pb in the untreated soil was reduced from 60 mg/kg to 0.55 mg/kg in RHB amended soils and non-detectable in other amended soils. RH-biochar/compost increased plant height, number of leaf and leaf area more than the others. Similarly, at minimum rate, it reduced root and shoot Pb by 91% and 86.0% respectively. Compost-modified rice husk biocharstabilised Pb in lead smelting slag contaminated soil reduced Pb plant uptake and improved plant growth. Lead stabilisation through the use of rice husk biochar with compost may be a green method for remediation of lead smelting slag-contaminated soil.

Incorporation of a nanotechnology-based additive in cementitious products for clay stabilisation

The mechanical performances and water retention characteristics of clays,stabilised by partial substitution of cement with by-products and inclusion of a nanotechnology-based additive called RoadCem(RC),are studied in this research.The unconfined compression tests and one-dimensional oedometer swelling were performed after 7 d of curing to understand the influence of addition of 1%of RC material in the stabilised soils with the cement partially replaced by 49%,59%and 69%of ground granulated blast furnace slag(GBBS)or pulverised fuel ash(PFA).The moisture retention capacity of the stabilised clays was also explored using the soil-water retention curve(SWRC)from the measured suctions.Results confirmed an obvious effect of the use of RC with the obtained strength and swell properties of the stabilised clays suitable for road application at 50%replacement of cement.This outcome is associated with the in-depth and penetrating hydration of the cementitious materials by the RC and water which results in the production of needle-like matrix with interlocking filaments e a phenomenon referred to as the‘wrapping’effect.On the other hand,the SWRC used to describe the water holding capacity and corresponding swell mechanism of clays stabilised by a proportion of RC showed a satisfactory response.The moisture retention of the RC-modified clays was initially higher but reduced subsequently as the saturation level increased with decreasing suction.This phenomenon confirmed that clays stabilised by including the RC are water-proof in nature,thus ensuring reduced porosity and suction even at reduced water content.Overall,the stabilised clays with the combination of cement,GGBS and RC showed a better performance compared to those with the PFA included.

Models to predict sunlight-induced photodegradation rates of contaminants in wastewater stabilisation ponds and clarifiers

Two kinetic models were established for conservative estimates of photodegradation rates of contaminants under sunlight irradiation,in particular for wastewater stabilisation ponds and clarifiers in conventional wastewater treatment plants.These two models were designated for(1)contaminants with high photolytic rates or high photolytic quantum yields,whose photodegradation is unlikely to be enhanced by aquatic photosensitisers;and(2)contaminants withstanding direct photolysis in sunlit waters but subjected to indirect photolysis.The effortlessly intelligible prediction procedure involves sampling and analysis of real water samples,simulated solar experiments in the laboratory,and transfer of the laboratory results to realise water treatment using the prediction models.Although similar models have been widely used for laboratory studies,this paper provides a preliminary example of translating laboratory results to the photochemical fate of contaminants in real waters.