Conversion factor analysis of self-balanced loading test of cast-in-situ piles based on analogue test method

Based on the characteristics of pile-soil interaction and the Mohr-Coulomb strength theory,a new method of determining the side friction at a pile-soil interaction is proposed.Combined with the actual engineering cases,the effectiveness of the analogue test method is verified by comparing it with the traditional anchor pile method and self-balanced method.Taking the self-balanced test of the bridge pile foundation in the Songhua River as an example,the conversion factor of sandy soil and weathered mudstone are confirmed by the analogue test method.The results show that the conversion factor of sandy soil and weathered mudstone in the Songhua River area should consider the geological conditions and the construction technology,etc.The standard values are relatively conservative.It is suggested that the engineering application should be properly revised.The recommended range of the conversion factor of sandy soil in this area is 0.65 to 0.85,and that of weathered mudstone is 1.0.

Research of in-situ hydraulic test method by using double packer equipment

Double packer equipment for hydraulic test can be used to measure pressure of test zone directly, and it is frequently used to perform many kinds of hydraulic tests and take groundwater sample from borehole. The test method of this equipment mainly includes the test design, implementation, interpretation and synthetic analysis. By adopting the double packer equipment for hydraulic test, the parameter distribution of rock permeability along borehole can be acquired, as well as the connectivity, water conductivity and water bearing capacity of the disclosed structure and the chemical characteristics of the deep groundwater. It is a necessary method for the research and evaluation of the complex hypotonicity terrace site selection under geological conditions. This method is not only suitable for the geological disposal of high level radioactive waste, but also can be used in the site selection of underground facilities such as storage of petroleum and carbon dioxide. Meanwhile, it has a good application prospect in other hydrogeological investigation fields.

Support design method for deep soft-rock tunnels in non-hydrostatic high in-situ stress field

Due to the long-term plate tectonic movements in southwestern China,the in-situ stress field in deep formations is complex.When passing through deep soft-rock mass under non-hydrostatic high in-situ stress field,tunnels will suffer serious asymmetric deformation.There is no available support design method for tunnels under such a situation in existing studies to clarify the support time and support stiffness.This study first analyzed the mechanical behavior of tunnels in non-hydrostatic in-situ stress field and derived the theoretical equations of the ground squeezing curve(GSC)and ground loosening curve(GLC).Then,based on the convergence confinement theory,the support design method of deep soft-rock tunnels under non-hydrostatic high in-situ stress field was established considering both squeezing and loosening pressures.In addition,this method can provide the clear support time and support stiffness of the second layer of initial support.The proposed design method was applied to the Wanhe tunnel of the China-Laos railway in China.Monitoring data indicated that the optimal support scheme had a good effect on controlling the tunnel deformation in non-hydrostatic high in-situ stress field.Field applications showed that the secondary lining could be constructed properly.

Stability and accuracy of central difference method for real-time dynamic substructure testing considering mass participation coefficient

For real-time dynamic substructure testing(RTDST),the influence of the inertia force of fluid specimens on the stability and accuracy of the integration algorithms has never been investigated.Therefore,this study proposes to investigate the stability and accuracy of the central difference method(CDM)for RTDST considering the specimen mass participation coefficient.First,the theory of the CDM for RTDST is presented.Next,the stability and accuracy of the CDM for RTDST considering the specimen mass participation coefficient are investigated.Finally,numerical simulations and experimental tests are conducted for verifying the effectiveness of the method.The study indicates that the stability of the algorithm is affected by the mass participation coefficient of the specimen,and the stability limit first increases and then decreases as the mass participation coefficient increases.In most cases,the mass participation coefficient will increase the stability limit of the algorithm,but in specific circumstances,the algorithm may lose its stability.The stability and accuracy of the CDM considering the mass participation coefficient are verified by numerical simulations and experimental tests on a three-story frame structure with a tuned liquid damper.

Testing method of rock structural plane using digital drilling

The rock mass consists of rock blocks and structural planes,which can reduce its integrity and strength.Therefore,accurately obtaining the characteristics of the rock mass structural plane is a prerequisite for evaluating stability and designing supports in underground engineering.Currently,there are no effective testing methods for the characteristic parameters of the rock mass structural plane in underground engineering.The paper presents the digital drilling technology as a new testing method of rock mass structural planes.Flawed rock specimens with cracks of varying widths and angles were used to simulate the rock mass structural planes,and the multifunctional rock mass digital drilling test system was employed to carry out the digital drilling tests.The analysis focuses on the variation laws of drilling parameters,such as drilling pressure and drilling torque,affected by the characteristics of prefabricated cracks,and clarifies the degradation mechanism of rock equivalent compressive strength.Additionally,an identification model for the characteristic parameters of rock mass structural planes during drilling is established.The test results indicate that the average difference of the characteristics of prefabricated cracks identified by the equivalent compressive strength is 2.45°and 0.82 mm,respectively.The identification model while drilling is verified to be correct due to the high identification accuracy.Based on this,a method for testing the characteristic parameters of the surrounding rock structural plane while drilling is proposed.The research offers a theoretical and methodological foundation for precise in situ identification of structural planes of the surrounding rock in underground engineering.

Study on determination method of in-situ stress using formation fracturing test and Kaiser effect method

A new method, which is based on formation fracturing test and Kaiser effect method, has been developed for confirming the oilfield in-situ stress in this paper. The new method has been used in a certain oilfield of China and the determined oilfield in-situ stresses is more accurate than that based on one single method.

Virtual rutting test of asphalt mixture using discrete element method

In order to investigate the permanent deformation behavior of asphalt mixtures from discontinuity, the virtual rutting test of asphalt mixtures is developed by the discrete element method （DEM）. A digital specimen generation procedure considering aggregate gradation and irregular shape is developed based on the probability theory and the Monte Carlo method. The virtual rutting test is then conducted based on the generated digital specimen. In addition, on the basis of the time-temperature superposition （TTS） principle, a calculation method is used to reduce the computation time of the virtual rutting test. The simulation results are compared with the laboratory measurements. The results show that the calculation method based on the TFS principle in the discrete element （DE） viscoelastic model can significantly reduce the computation time. The deformation law of asphalt mixtures in the virtual rutting test is similar to the laboratory measurements, and the deformation and the dynamic stability of the virtual rutting test are slightly greater than the laboratory measurements. The two-dimensional virtual rutting test can predict the permanent deformation performance of asphalt mixtures.

Virtual fracture test of asphalt mixture based on discrete element method

In order to study fracture behaviors of asphalt mixtures, virtual tests of the two-dimensional（2D） microstructure based on the discrete element method（ DEM） are designed. The virtual structure of the 2D digital specimen of asphalt mixture is generated based on a particle generation program, in which the gradation and the irregular shapes of aggregates are considered. With the 2D digital specimens, a DEM-based mixture model is established and center-point beam fracture simulation tests are conducted by the DEM. Meanwhile, a series of calibration tests are carried out in laboratory to evaluate the DEM model and validate the methods of virtual fracture tests. The test results indicate that the fracture intensity of asphalt mixtures predicted by the DEM matches very well with the intensity obtained in laboratory. It is concluded that the microstructural virtual tests can be used as a supplemental tool to evaluate fracture properties of asphalt mixtures.

Research on the Testing Methods of Instrumental System in the Marine Magnetic Survey

Testing methods of instrumental system in the marine magnetic survey have been studied in this paper, and the feasibility of each method has been testified by the observed data. The conclusion shows that the method brought out can effectively eliminate the systematic error caused by the instrumental system, and greatly improve the surveying precision and the reliability of the survey results.

New Fatigue Test and Statistical Method for Metallic Materials Used in Vehicle Transmissions

Aim To improve the efficiency of fatigue material tests and relevant statistical treatment of test data. Methods\ Least square approach and other special treatments were used. Results and Conclusion\ The concepts of each phase in fatigue tests and statistical treatment are clarified. The method proposed leads to three important properties. Reduced number of specimens brings to the advantage of lowering test expenditures. The whole test procedure has more flexibility for there is no need to conduct many tests at the same stress level as in traditional cases.

Method of Growth in Finding the Test Cube of Industrial Robots

In order to find the test cube for industrial robots as specified by ISO 9283, a seed cube is grown up in an irregular working space of the robot, provided that the corners of the cube do not exceed the boundary of the working space. All possible cubes are searched, and the cube with the maximum volume is selected. The calculation examples show that the method of growth can be used for a variety of industrial robots. The method of growth can determine the test cube and test points of irregular working space according to ISO 9283, and can avoid blindness and randomness in the selection of test points.

Methodology Validation of Microbial Limit Test of Bupi Qiangli Ointment

[Objective] This study was conducted to establish a microbial limit test method for Bupi Qiangli Ointment. [Method] The conventional method and medium dilution method were used for bacterial, mold and yeast counting in sample recovery test. [Result] The medium dilution method （1：10 test solution, 0.5 ml/plate） could effectively eliminate the inhibition effect of the Bupi Qiangli Ointment, and the recovery of Staphylococcus aureus was greater than 70% in the 3 batches of samples; and the conventional method exhibited the recoveries of E. coil, Bacillus subtilis, Candida albicans and Aspergillus greater than 70% in the 3 batches of samples. [Conclusion] Due to Bupi Qiangli Ointment has strongly antibacterial effect on Staphylococcus au- reus, the medium dilution method was used for bacterial counting, and the conventional method was used for mold and yeast counting; and the conventional method was used for controlled bacterium examination of E. coll.

Investigation on the test method of rupture forces of thermal bonding seams in nonwovens shopping bags

超声波热黏合的非织造布接缝不同于普通机织物和针织物等的车缝接缝。运用正交试验设计方法，对纺粘法PP非织造布购物袋热黏合接缝断裂强力测试中的试样宽度、拉伸速率和隔距三个因素进行优化。试验结果表明，试样宽度对纺粘法PP非织造布热黏合接缝断裂强力的测试结果影响最大，并且接缝的断裂强力随着试样宽度的增加而增加。选用试样宽度为200mm、拉伸速率为50mm／min、隔距为100mm的组合所得出的测试结果能比较真实地反映实际的接缝断裂强力。

Research on in-situ condition preserved coring and testing systems

As shallow resources are increasingly depleted,the mechanics'theory and testing technology of deep insitu rock has become urgent.Traditional coring technologies obtain rock samples without retaining the in-situ environmental conditions,leading to distortion of the measured parameters.Herein,a coring and testing systems retaining in-situ geological conditions is presented:the coring system that obtains in-situ rock samples,and the transfer and testing system that stores and analyzes the rocks under a reconstructed environment.The ICP-Coring system mainly consists of the pressure controller,active insulated core reactor and insulation layer and sealing film.The ultimate bearing strength of 100 MPa for pressurepreservation,temperature control accuracy of 0.97%for temperature-retained are realized.CH_(4)and CO permeability of the optimized sealing film are as low as 3.85 and 0.33 ppm/min.The average tensile elongation of the film is 152.4%and the light transmittance is reduced to 0%.Additionally,the pressure and steady-state temperature accuracy for reconstructing the in-situ environment of transfer and storage system up to 1%and±0.2 is achieved.The error recorded of the noncontact sensor ring made of lowdensity polymer is less than 6%than that of the contact test.The system can provide technical support for the deep in-situ rock mechanics research,improving deep resource acquisition capabilities and further clarifying deep-earth processes.

Stress initialization methods for dynamic numerical simulation of rock mass with high in-situ stress

In the context of deep rock engineering,the in-situ stress state is of major importance as it plays an important role in rock dynamic response behavior.Thus,stress initialization becomes crucial and is the first step for the dynamic response simulation of rock mass in a high in-situ stress field.In this paper,stress initialization methods,including their principles and operating procedures for reproducing steady in-situ stress state in LS-DYNA,are first introduced.Then the most popular four methods,i.e.,explicit dynamic relaxation(DR)method,implicit-explicit sequence method,Dynain file method and quasi-static method,are exemplified through a case analysis by using the RHT and plastic hardening rock material models to simulate rock blasting under in-situ stress condition.Based on the simulations,it is concluded that the stress initialization results obtained by implicit-explicit sequence method and dynain file method are closely related to the rock material model,and the explicit DR method has an obvious advantage in solution time when compared to other methods.Besides that,it is recommended to adopt two separate analyses for the whole numerical simulation of rock mass under the combined action of in-situ stress and dynamic disturbance.

Analysis of the integrated test and evaluation methods of tidal current energy generating devices in the offshore testing site

Actual sea condition testing and inspection and evaluation method research are carried out for tidal energy devices to provide scientific and effective technical support for the ocean high-tech achievement transformation and marine renewable energy development. By analyzing three core indicators, including the power output characteristics of the tidal current device, the generating capacity, energy conversion efficiency, proposed the test contents and evaluation methods of indicators are proposed in this paper; and based on the research of wind farms, power quality testing and assessment methods of offshore tidal energy device are proposed; given the security access to the test contents of tidal current energy device, tidal current energy device running conditions in the testing ground are comprehensively assessed.

Real-time embedded software testing method based on extended finite state machine

The reliability of real-time embedded software directly determines the reliability of the whole real-time embedded sys- tem, and the effective software testing is an important way to ensure software quality and reliability. Based on the analysis of the characteristics of real-time embedded software, the formal method is introduced into the real-time embedded software testing field and the real-time extended finite state machine （RT-EFSM） model is studied firstly. Then, the time zone division method of real-time embedded system is presented and the definition and description methods of time-constrained transition equivalence class （timeCTEC） are presented. Furthermore, the approaches of the testing sequence and test case generation are put forward. Finally, the proposed method is applied to a typical avionics real- time embedded software testing practice and the examples of the timeCTEC, testing sequences and test cases are given. With the analysis of the testing result, the application verification shows that the proposed method can effectively describe the real-time embedded software state transition characteristics and real-time requirements and play the advantages of the formal methods in accuracy, effectiveness and the automation supporting. Combined with the testing platform, the real-time, closed loop and automated simulation testing for real-time embedded software can be realized effectively.

Assessment of rapid impact compaction in ground improvement from in-situ testing

Ground improvement has been used on many construction sites to densify granular materials, in other word, to improve soil properties and reduce potential settlement. This work presents a case study of ground improvement using rapid impact compaction （RIC）. The research site comprises the construction of workshop and depots as part of railway development project at Batu Gajah-Ipoh, Malaysia. In-situ testing results show that the subsurface soil comprises mainly of sand and silty sand through the investigated depth extended to 10 m. Groundwater is approximately 0.5 m below the ground surface. Evaluation of improvement was based on the results of pre- and post-improvement cone penetration test （CPT）. Interpretation software has been used to infer soil properties. Load test was conducted to estimate soil settlement. It is found that the technique succeeds in improving soil properties namely the relative density increases from 45% to 70%, the friction angle of soil is increased by an average of 3°, and the soil settlement is reduced by 50%： The technique succeeds in improving soil properties to approximately 5.0 m in depth depending on soil uniformity with depth.

Studying the mechanical properties of the soil-root interface using the pullout test method

It is important to quantify the effect of the root diameter, the embedment length of the root and load speed on the soil-root interface mechanical properties for studying the root anchorage. The soilroot interface mechanical properties can be obtained through the pullout force and root slippage curve(F-S curve). About 120 Pinus tabulaeformis single roots whose diameters ranged from 1 mm to 10 mm divided into 6 groups based on different root embedment length(50 mm, 100 mm and 150 mm) and different load velocity(10 mm·min^(-1), 50 mm·min^(-1), 100 mm·min^(-1) and 300 mm·min^(-1)) were investigated using the pullout method. This study aims to explore the mechanical properties of the soil-root interface in the real conditions using the pullout test method. The results showed two kinds of pullout test failure modes during the experimental process: breakage failure and pullout failure. The results showed that the roots were easier to be broken when the root diameter was smaller or the loading speed was larger. The relationship between the maximum anchorage force and root diameter was linear and the linearly dependent coefficient(R^2) was larger than 0.85. The anchorage force increased with the root embedment length. An increase of 10%^(-1)5% for the maximumanchorage force was found when load speed increased from 10 to 300 mm.min^(-1). The mean peak slippage of the root was from 13.81 to 35.79 mm when the load velocity varied from 10 to 300 mm.min^(-1). The study will be helpful for the design of slopes reinforced by vegetation and in predicting risk of uprooting of trees, and will have practical benefits for understanding the mechanism of landslide.

Load Reduction Test Method of Similarity Theory and BP Neural Networks of Large Cranes

Static load tests are an important means of supervising and detecting a crane＇s lift capacity. Due to space restrictions, however, there are difficulties and potential danger when testing large bridge cranes. To solve the loading problems of large-tonnage cranes during testing, an equivalency test is proposed based on the similarity theory and BP neural networks. The maximum stress and displacement of a large bridge crane is tested in small loads, combined with the training neural network of a similar structure crane through stress and displacement data which is collected by a physics simulation progressively loaded to a static load test load within the material scope of work. The maximum stress and displacement of a crane under a static load test load can be predicted through the relationship of stress, displacement, and load. By measuring the stress and displacement of small tonnage weights, the stress and displacement of large loads can be predicted, such as the maximum load capacity, which is 1.25 times the rated capacity. Experimental study shows that the load reduction test method can reflect the lift capacity of large bridge cranes. The load shedding predictive analysis for Sanxia 1200 t bridge crane test data indicates that when the load is 1.25 times the rated lifting capacity, the predicted displacement and actual displacement error is zero. The method solves the problem that lifting capacities are difficult to obtain and testing accidents are easily possible when 1.25 times related weight loads are tested for large tonnage cranes.