Transparent conducting indium-tin-oxide(ITO) film as full front electrode in Ⅲ–Ⅴ compound solar cell

The application of transparent conducting indium-tin-oxide （ITO） film as full front electrode replacing the conven- tional bus-bar metal electrode in III-V compound GalnP solar cell was proposed. A high-quality, non-rectifying contact between ITO and 10 nm N＋-GaAs contact layer was formed, which is benefiting from a high carrier concentration of the terrilium-doped N＋-GaAs layer, up to 2×10^19 cm^-3. A good device performance of the GalnP solar cell with the ITO electrode was observed. This result indicates a great potential of transparent conducting films in the future fabrication of larger area flexible III-V solar cell.

Improvement of the light output and contact resistance of InGaN-based light-emitting diodes based on tantalum-doped indium tin oxide as p-type electrodes

This paper reports that highly transparent and low resistance tantalum-doped indium tin oxide （Ta-doped ITO） films contacted to p-type GaN have been prepared by the electron-beam evaporation technique. The Ta-doped ITO contacts become Ohmic with a specific contact resistance of $／sim 5.65／times 10^{ - 5}$$／Omega ／cdot$cm$^{2}$ and show the transmittance of $／sim $98% at a wavelength of 440nm when annealed at 500／du. Blue light emitting diodes （LEDs） fabricated with Ta-doped ITO p-type Ohmic contact layers give a forward-bias voltage of 3.21V at an injection current of 20mA. It further shows that the output power of LEDs with Ta-doped ITO contacts is enhanced 62% at 20mA in comparison with that of LEDs with conventional Ni/Au contacts

Preparation and Characterization of Indium Doped Tin Oxide （ITO） via a Solvothermal Method

Tin-doped Indium Oxide （ITO） has been successfully prepared via solvothermal method with a mixture of Indium（Ill） acetylacetonate and Tin（IV） bis（acetylacetonate）dichioride in oleyamine solvent under the condition of the different reaction time from 12 h to 48 h for the first time. The morphology, phase composition and particle size of the ITO powder were characterized by TEM and XRD. Two significant properties required for ITO samples to become noncarbon support for Pt in PEMFCs including specific surface area and electrical conductivity were studied.

Preparation of indium tin oxide targets with a high density and single phase structure by normal pressure sintering process

The present work mainly describes the technology for preparing indium-tin oxide （ITO） targets by cold isostatic pressing （CIP） and normal pressure sintering process. ITO powders were produced by chemical co-precipitation and shaped into an ITO green compact with a relative density of 60% by CIP under 300 MPa. Then, an ITO target with a relative density larger than 99.6% was obtained by sintering this green compact at 1550℃ for 8 h. The effects of forming pressure, sintering temperature and sintering time on the density of the target were inves- tigated. Also, a discussion was made on the sintering atmosphere.

Microstructure and properties of indium tin oxide thin films deposited by RF-magnetron sputtering

Tin-doped indium oxide （ITO） thin films were prepared using conventional radio frequency （RF） planar magnetron sputtering equipped with IR irradiation using a ceramic target of In2O3/SnO2 with a mass ratio of 1：1 at various IR irradiation temperatures T1 （from room temperature to 400℃）. The refractive index, deposited ratio, and resistivity are functions of the sputtering Ar gas pressure. The microstructure of ITO thin films is related to IR T1, the crystalline seeds appear at T1= 300℃, and the films are amorphous at the temperature ranging from 27℃ to 400℃. AFM investigation shows that the roughness value of peak-valley of ITO thin film （Rp-v） and the surface microstructure of rio thin films have a close relation with T1. The IR irradiation results in a widening value of band-gap energy due to Burstein-Moss effect and the maximum visible transmittance shifts toward a shorter wavelength along with a decrease in the film＇s refractive index. The plasma wavelength and the refractive index of ITO thin films are relative to the T1. XPS investigation shows that the photoelectrolytic properties can be deteriorated by the sub-oxides. The deterioration can be decreased by increasing the oxygen flow rote （fo2）, and the mole ratio of Sn/In in the samples reduces with an increase info2.

Effects of SiO_2 and TiO_2 on resistance stabilities of flexible indium-tin-oxide films prepared by ion assisted deposition

Inorganic buffer layers such as SiO2 or TiO2 and transparent conductive indium-tin-oxide （ITO） films were prepared on polyethylene terephthalate （PET） substrates by ion assisted deposition （IAD） at room temperature, and the effects of SiO2 and TiOzon the bending resistance performance of flexible ITO films were investigated. The results show that ITO films with SiO2 or TiO2 buffer layer have better resistance stabilities compared to ones without the buffer layer when the ITO films are inwards bent at a bending radius more than 1.2 cm and when the ITO films are outwards bent at a bending radius from 0.8 cm to 1.2 cm. 1TO films with SiO2 buffer layer have better resistance sta- bilities compared to ones with TiO2 buffer layer after the ITO fdms are bent several hundreds of cycles at the same bending radius, for the adhesion of SiO2 is stronger than that of TiO2. The compressive stress resulted from inward bending leads to the formation of more defects in the ITO films compared with the tensile stress arising from outward bending. SiO2 and TiO2 buffer layers can effectively improve the crystallinity of ITO films in （400）, （440） directions.

Dependence of Performance of Organic Light-emitting Devices on Sheet Resistance of Indium-tin-oxide Anodes

The dependence of the performance of organic light-emitting devices（OLEDs） on the sheet resistance of indiumtin-oxide（ITO） anodes was investigated by measuring the steady state current density brightness voltage characteristics and the electroluminescent spectra. The device with a higher sheet resistance anode shows a lower current density, a lower brightness level, and a higher operation voltage. The electroluminescence（EL） efficiencies of the devices with the same structure but different ITO anodes show more complicated differences. Furthermore, the shift of the light-emitting zone toward the anode was found when an anode with a higher sheet resistance was used. These performance differences are discussed and attributed to the reduction of hole injection and the increase in voltage drop over ITO anode with the increase in sheet resistance.

Effect of Sn^(4+) content on properties of indium tin oxide nanopowders

Indium tin oxide(ITO)nanopowders were prepared by a modified chemical co-precipitation process.The influence of different SnO2 contents on the decomposition behavior of ITO precursors,and on the phase and morphology of ITO precursors and ITO nanopowders were studied by X-ray diffractometry,transmission electron microscopy and differential thermal and thermogravimetry analysis methods.The TG-DSC curves show that the decomposition process of precursor precipitation is completed when the temperature is close to 600 ℃and the end temperature of decompositionis somewhat lower when the doping amount of SnO2 is increased.The XRD patterns indicate that the solubility limit of Sn4+ relates directly to the calcining temperature. When being calcined at 700℃,a single phase ITO powder with 15%SnO2(mass fraction)can be obtained.But,when the calcining temperature is higher than 800℃,the phase of SnO2 will appear in ITO nanopowders which contain more than 10%SnO2.The particle size of the ITO nanopowders is 15-25 nm.The ITO nanoparticles without Sn have a spherical shape,but their morphology moves towards an irregular shape when being doped with Sn4+.

Microstructure and properties of indium tin oxide thin films deposited by RF-magnetron sputtering

Tin-doped indium oxide （ITO） thin films were prepared using conventional radio frequency （RF） planar magnetron sputtering equipped with IR irradiation using a ceramic target of In2O3/SnO2 with a mass ratio of 1∶1 at various IR irradiation temperatures T1 （from room temperature to 400?℃）. The refractive index,deposited ratio,and resistivity are functions of the sputtering Ar gas pressure. The microstructure of ITO thin films is related to IR T1,the crystalline seeds appear at T1=300?℃,and the films are amorphous at the temperature ranging from 27?℃ to 400?℃. AFM investigation shows that the roughness value of peak-valley of ITO thin film （R p-v ） and the surface microstructure of ITO thin films have a close relation with T1. The IR irradiation results in a widening value of band-gap energy due to Burstein-Moss effect and the maximum visible transmittance shifts toward a shorter wavelength along with a decrease in the film’s refractive index. The plasma wavelength and the refractive index of ITO thin films are relative to the T1. XPS investigation shows that the photoelectrolytic properties can be deteriorated by the sub-oxides. The deterioration can be decreased by increasing the oxygen flow rate （fo2）,and the mole ratio of Sn/In in the samples reduces with an increase in fo2.

模压成型压力对氧化铟锡(ITO)靶材性能影响研究

以化学共沉淀-煅烧法制备的纳米ITO粉体为原料,通过模压、冷等静压成型,采用常压烧结法制备了ITO靶材,研究了模压成型压力对ITO靶材相对密度、电阻率和晶粒尺寸的影响。结果表明,模压成型压力60 MPa且烧结条件适宜时,制得的ITO靶材相对密度为99.81%、电阻率为1.707×10^(-4)Ω·cm、平均晶粒尺寸为7.62μm。研究结果可为ITO靶材的致密化与大型化生产提供借鉴。

退火温度对ITO/Cu/AZO透明导电薄膜结构及性能的影响

采用射频与直流磁控交替溅射法在石英玻璃载玻片上制备了氧化铟锡(ITO)/Cu/Al掺杂ZnO(AZO)(45 nm/10 nm/45 nm)组合结构的透明导电薄膜,并在不同退火温度下对薄膜进行真空热处理。利用X射线衍射仪(XRD)、紫外-可见分光光度计、四探针电阻测试仪等表征手段,系统地研究了退火温度对ITO/Cu/AZO复合薄膜晶体结构和光电性能的影响。结果显示,经过不同温度的真空退火处理,薄膜的晶体结构和导电性能得到显著改善和提高,薄膜可见光平均透过率随着退火温度的升高先增加后降低。对比发现,在气压5×10^(-3)Pa、温度150℃下退火制备的ITO/Cu/AZO结构薄膜表现出最佳的综合性能,薄膜具有较强的(222)和(440)晶面衍射峰,在400~800 nm光波范围平均透过率约为80.5%,电导率约为1.76×10^(3) S/cm,综合品质因数达到约2.12×10^(-3)/Ω。

Electrophoretic deposition of a supercapacitor electrode of activated carbon onto an indium-tin-oxide substrate using ethyl cellulose as a binder

A transparent energy storage device is an essential component for transparent electronics.The increasing demand for high-power devices stimulates the development of transparent supercapacitors with high power density.A transparent electrode for such supercapacitors can be assembled via the electrophoretic deposition of an active material powder with a binder onto a transparent substrate.The properties of the binder critically influence the electrochemical behavior and performance of the resulting electrode.Ethyl cellulose(EC)is known as an eco-friendly,transparent,flexible,and inexpensive material.Here,we fabricated an electrode film with EC binder via electrophoretic deposition on an indium tin oxide(ITO)substrate instead of using the conventional polytetrafluoroethylene(PTFE)binder.The assembled electrodes with EC and PTFE were compared to investigate the feasibility of EC as a binder from different perspectives,including homogeneity,wettability,electrochemical behavior,and mechanical stability.The EC enabled the formation of a homogeneous film composed of smaller particles and with a higher specific capacitance compared with films prepared with PTFE.The annealing improved the adhesion strength of the EC because of its glass transition;however,its hydrophobic nature limited utilization of the active material for charge storage.Subsequent electrochemical activation improved the wettability of the electrode,resulting in an increased capacitance of 60 F g^(-1).Furthermore,even with the lower wettability of EC compared with that of PTFE,better rate performance was possible with the EC electrode.The increased mechanical stability after the annealing process ensured an excellent cycle life of 95%capacitance retention for 15,000 cycles.

Electrochemical Behavior and Its Electrocatalytic Activity of A P-Mo Heteropolyanion Modified ITO Electrode

s: A new method for the preparation of an organic-inorganic composite film of the heteropolyanion has been developed by modifying P(Mo2O7)6-7 to the indium tin oxide (ITO) electrode surface. The modified electrode displayed a strong catalytic activity towards the reduction of IO3-. In the range of 1.0?0-6~5?0-4mol/L, the catalytic current was linear proportional to the IO3- concentration.

基于ITO的近红外波段远场辐射的动态调控

由近零介电常数材料构成的纳米天线,其折射率具有强度依赖性,可以用来调控远场辐射模式。因此,提出了基于氧化铟锡(ITO)的混合光学天线,以光学方式调控远场辐射角的偏转。并且,基于ITO和线性介电材料(nL)的混合结构天线可实现在近红外波段(1000 nm~1600 nm)偏转角的调控。随着入射光强度的增加,远场辐射角度最大可达到21.6°。基于混合结构,通过改变光学强度和波段进而影响辐射模式,最终调控偏转角度,这为进一步研究和应用于光束转向和光学调制奠定了基础。

基于ITO柔性透明偏振不敏感超宽带超材料吸波器

设计了一种基于电阻膜氧化铟锡(ITO)的柔性透明偏振不敏感超宽带吸波器,并对其进行了分析和制备。利用ITO电阻膜图样产生欧姆损耗实现高吸收。仿真结果表明设计的超材料吸波器在2.7~12.1 GHz范围内可实现高于90%吸收率,相对带宽为127%,覆盖了S、C、X波段。由于结构的对称性,该吸波器对偏振角不敏感,且在45°宽入射角范围内具有高吸收率。通过阻抗匹配、等效电路理论、电场以及电流分布、结构参数分析了吸收机理。实验测量结果与仿真结果一致。该超材料吸波器具有超宽带吸收、极化不敏感和灵活性好等优点,可广泛应用于电磁屏蔽、雷达隐身技术等领域。

基底温度对射频磁控溅射PI基ITO薄膜的影响

采用射频(RF)磁控溅射法在柔性耐高温聚酰亚胺(PI)薄膜上沉积了氧化铟锡(ITO)薄膜,研究了基底温度对ITO薄膜性能的影响。运用四探针测试仪研究了基底温度对ITO薄膜方块电阻及电阻率的影响,并用扫描电子显微镜(SEM)、X射线衍射仪(XRD)研究了基底温度对ITO薄膜表面形貌及结晶度的影响。采用X射线光电子能谱仪(XPS)、附着力测试仪分析电学性能最优的样品化学组成与附着力。研究结果表明,ITO薄膜方块电阻及电阻率随基底温度上升先下降后上升,在基底温度为250℃时,ITO薄膜方块电阻为14.1Ω/□,电阻率为1.9×10^(-4)Ω·cm,基膜附着力好,薄膜结晶度高,(222)晶面存在择优取向。

Gold nanoparticles attached NH^(2+) ion implantation-modified indium tin oxide electrode:Characterization and electrochemical studies

An NH2+ ion implantation-modified indium tin oxide film was prepared and the implantation of amino groups on the indium tin oxide substrate was verified by X-ray photoelectron spectroscopy analysis.The gold nanoparticles attached surface could be obtained by self-assembly of different sized colloidal gold nanoparticles onto the NH2+ ion implantation-modified indium tin oxide surface.By scanning electron microscopy and electrochemical techniques,the as-prepared AuNPs attached NH2+ ion implantation-modified indium tin oxide electrode was characterized and compared with bare indium tin oxide electrode.Using a [Fe(CN)6]3 /[Fe(CN)6]4 redox probe,the increasingly facile heterogeneous electron transfer kinetics resulting from the attached gold nanoparticle arrays was observed.The gold nanoparticle arrays exhibited high catalytic activity toward the electro-oxidation of nitric oxide,which could provide electroanalytical application for nitric oxide sensing.

Immobilization of Hemoglobin on Cobalt Nanoparticles-modified Indium Tin Oxide Electrode： Direct Electrochemistry and Electrocatalytic Activity

A cobalt nanoparticles-attached indium tin oxide（CoNPs/ITO） electrode was applied to the immobilization of hemoglobin（Hb） and an Hb modified CoNPs/ITO electrode（Hb/CoNPs/ITO） was prepared. The direct electron transfer of Hb was shown by the well-behaved voltammetric responses for Hb/CoNPs/ITO electrode and the effects of scan rate and pH value were observed. Based on the catalytic activity of Hb immobilized on the CoNPs/ITO electrode toward the reduction of H2O2, a mediator-free H2O2 sensor was developed. A linear relationship existed between the catalytic current and the H2O2 concentration in a range of 1.0--100.0 μmol/L with a detection limit （S/N=3） of 0.2μmol/L.

ITO薄膜微结构对其光电性质的影响

采用磁控溅射法在玻璃衬底上沉积掺锡氧化铟(ITO)薄膜,用X射线衍射(XRD)、X射线光电子能谱(XPS)技术和电导率、透射光谱测试技术,研究真空低温退火后ITO薄膜微结构、薄膜电导率、光谱透射率的变化.研究表明,真空低温退火使得晶体微结构得到改善,晶体呈(222)择优取向,晶体的结晶颗粒变大.不同价态的Sn对In3+的替代引起晶格结构和ITO薄膜的载流子浓度的变化,从而影响到薄膜的导电性和透射率,证明了真空退火下氧化铟薄膜微结构变化是影响薄膜电导率与透射率的主要原因,为研制新型光电器件的透明电极提供了参考.

制备工艺对纳米级铟锡氧化物(ITO)形貌和电性能的影响

以SnCl4·5H2O、In和浓盐酸为原料,采用化学共沉淀法制备出了纳米级锡掺杂氧化铟(ITO)导电微粉,系统地研究了掺杂量,共沉淀温度,pH值,热处理时间、温度对粉体粒度、形貌和电性能的影响规律。研究表明,合成的ITO粉体分散性较好、导电性能优异,粒径在40nm左右具有立方铁锰矿结构。在ITO纳米导电粉的制备过程中,共沉淀温度和滴定终点pH值对其形貌和性能有很大影响,当共沉淀温度在60℃左右,pH=6时制得的粉体性能最佳。煅烧条件对粉体的形貌、粒度和导电性也有较大的影响,在700℃,4h条件下可以制得导电性能良好,结晶完好,粒度分布均匀的ITO粉体。掺入Sn(Ⅳ)的量对载流子的迁移率有很大的影响,在掺杂浓度为10%左右可制得导电性极佳的纳米ITO粉体。