Dynamic performance and parameter optimization of a half-vehicle system coupled with an inerter-based X-structure nonlinear energy sink

Inspired by the demand of improving the riding comfort and meeting the lightweight design of the vehicle, an inerter-based X-structure nonlinear energy sink(IXNES) is proposed and applied in the half-vehicle system to enhance the dynamic performance. The X-structure is used as a mechanism to realize the nonlinear stiffness characteristic of the NES, which can realize the flexibility, adjustability, high efficiency, and easy operation of nonlinear stiffness, and is convenient to apply in the vehicle suspension, and the inerter is applied to replacing the mass of the NES based on the mass amplification characteristic. The dynamic model of the half-vehicle system coupled with the IX-NES is established with the Lagrange theory, and the harmonic balance method(HBM) and the pseudo-arc-length method(PALM) are used to obtain the dynamic response under road harmonic excitation. The corresponding dynamic performance under road harmonic and random excitation is evaluated by six performance indices, and compared with that of the original half-vehicle system to show the benefits of the IX-NES. Furthermore, the structural parameters of the IX-NES are optimized with the genetic algorithm. The results show that for road harmonic and random excitation, using the IX-NES can greatly reduce the resonance peaks and root mean square(RMS) values of the front and rear suspension deflections and the front and rear dynamic tire loads, while the resonance peaks and RMS values of the vehicle body vertical and pitching accelerations are slightly larger.When the structural parameters of the IX-NES are optimized, the vehicle body vertical and pitching accelerations of the half-vehicle system could reduce by 2.41% and 1.16%,respectively, and the other dynamic performance indices are within the reasonable ranges.Thus, the IX-NES combines the advantages of the inerter, X-structure, and NES, which improves the dynamic performance of the half-vehicle system and provides an effective option for vibration attenuation in the vehicle engineering.

THERMAL STRESSES RELAXATION DESIGN OF Ni/NiFe_(2)O_(4) SYSTEM FUNCTIONALLY GRADED CERMET INERT ANODE

The thermal stresses relaxation of Ni/NiFe2O4 system functionally graded cermet inert anode for aluminum electrolysis was optimally designed. The transient thermal stresses of the inert anode under complex boundary condition during high-temp （955℃） electrolysis were calculated using the finite-element software ANSYS, the influence of different parameters on the distribution of the thermal stresses were analyzed. The results showed that, during the process of thermal shock, the thermal hoop tensile stress on the surface of the anode is very large, which is possibly the major cause of anode crack; when the radius of the anode is between 0.05-0.15m, a range that can be realized by recent manufacturing technology, the optimum composition distribution exponent p is 0.25; The hoop tensile stresses reduce with the decrease of anode scale and also decrease with the decrease of the convection coefficient between the electrolyte and the anode.

Optimal design of inerter systems for the force-transmission suppression of oscillating structures

When dealing with the oscillations of fixed-base structures or machines induced by external forces,suppressing the vibrational impact on the adjacent structures and the environment helps to maintain the structural durability and ensure the users′comfort level.This study proposed an inerter-based optimal solution to suppress the vibrational forces and energy transmitted to the supporting ground by utilizing the great potential of the inerter.For the external force,which contains various frequency bands,the stochastic response and an energy balance analysis are conducted to evaluate the force transmissibility,structural displacement,and vibration power flow.Given the benefits of the inerter,a transmitted-force-based optimal design framework is proposed for inerter systems,of which the effectiveness is validated by numerical examples.The obtained results show that inerter systems are capable of providing significant reductions in the structural displacement and the force transmitted to the supporting ground.Particularly,the closed-form power equation indicated that a grounded inerter can suppress the force transmission and vibrational energy,thus leading to a less negative impact on the ground and environment.Revealing the working mechanism and optimal design strategy of the inerter can help solve the force-transmission control problem experienced by some practical structures.

Study on the Inert Coordination Compound in the System of“Molybdenum(Ⅵ)—TAE—Hydroxylamine”and its Analytical Application

In the presence of ethyl alcohol or emulsifier OP,molybdenum(Ⅵ) forms 1∶1∶1'water soluble colored coordination com- pound with both of 2-(2-thiazolylazo)-5-diethylaminophenol (abbreviation TAE) and hydroxylamine.This deep blue coordination compound is inert characteristically and remains stable in 1.7 mol/L sulfuric acid,2.4 mol/L hydrochloric or ni- tric acid.It will not be decomposed by masking agents even on boiled,while in that case,almost all the colored coordination com- pounds formed by other metal ions will be decomposed completely.This inert character of the coordination compound of molybdenum(Ⅵ) and its utilization in improving the analytical selectivity have been discussed.In the coexistence of various for- eign ions,especially in the presence of a great quantity of tungsten,which always interferes with the determination of molybdenum,the direct determination of molybdenum in the aqueous solution by applying this system has shown an acceptable sensitivity and reproducibility.From the results of determination in some synthetic and standard samples,it seems feasible to use this system in the determination of molybdenum in nonferrous alloys.

Theoretically Catalytic Synthesis of 5-Nitro-1,2,4-Triazol-3-One in Inert Gas Clustered System (X₆, X = He, Ne)

Inert gas-clustered systems (Xn, X = He, Ne, Ar and n = 2 - 20) were established in this study and their stability as a result of interparticulate interaction was examined. Ferric chloride and ferrous oxides were used as catalysts to promote reaction, and 5-nitro-1,2,4-triazol-3-one (NTO) was theoretically synthesized under an inert gas (X6)-clustered environment in this study. The raw material, urea, initially underwent chlorination using chlorine as the reagent, followed by amination, formylation and nitration. Reaction routes closely related to the experimental processes were successfully constructed, and the corresponding energy barriers were estimated for each elementary reaction. The findings revealed that the average errors in the B3LYP/6-31G(d, p)-calculated geometry and vibrational frequency of NTO in an Ne6 system relative to the observed values were 0.83% and 1.84%, respectively. The neon gas-clustered system achieved greater stabilization, which results from the difference in self-consistent field energy (ESCF), than the corresponding stabilization acquired in a helium- or argon-based system. Ferric chloride serves as a good catalyst to reduce the energy barrier of the chlorination reaction, and ferrous oxide is suitable for catalyzing the amination, formylation and nitration reactions, although nitric acid is the better agent for nitration. The catalytic Ne6-clustered reaction system is suggested to be a more feasible pathway for the synthesis of NTO.

Study on vibration reduction of two-scale system coupled with dynamic vibration absorber

The dynamic vibration absorber with inerter and grounded stiffness(IGDVA)is used to control a two-scale system subject to a weak periodic perturbation.The vibration suppression effect is remarkable.The amplitude of the main system coupled with absorber is significantly reduced,and the high frequency vibration completely disappears.First,through the slow-fast analysis and stability theory,it is found that the stability of the autonomous system exerts a notable regulating effect on the vibration response of the non-autonomous system.After adding the dynamic vibrator absorber,the center in the autonomous system changes to an asymptotically stable focus,consequently suppressing the vibration in the non-autonomous system.Further research reveals that the parameters of the absorber affect the real parts of the eigenvalues of the autonomous system,thereby regulating the stability of the system.Transitioning from a qualitative standpoint to a quantitative approach,a comparison of the solutions before and after the introduction of the dynamic absorber reveals that,when the grounded stiffness ratio and the mass ratio of the dynamic absorber are not equal,the high-frequency part in the analytical solution disappears.As a result,this leads to a reduction in the amplitude of the trajectory,achieving a vibration reduction effect.

Parameters Optimization and Performance Evaluation of the Tuned Inerter Damper for the Seismic Protection of Adjacent Building Structures

In order to improve the seismic performance of adjacent buildings,two types of tuned inerter damper(TID)damping systems for adjacent buildings are proposed,which are composed of springs,inerter devices and dampers in serial or in parallel.The dynamic equations of TID adjacent building damping systems were derived,and the H2 norm criterion was used to optimize and adjust them,so that the system had the optimum damping performance under white noise random excitation.Taking TID frequency ratio and damping ratio as optimization parameters,the optimum analytical solutions of the displacement frequency response of the undamped structure under white noise excitation were obtained.The results showed that compared with the classic TMD,TID could obtain a better damping effect in the adjacent buildings.Comparing the TIDs composed of serial or parallel,it was found that the parallel TIDs had more significant advantages in controlling the peak displacement frequency response,while the H2 norm of the displacement frequency response of the damping system under the coupling of serial TID was smaller.Taking the adjacent building composed of two ten-story frame structures as an example,the displacement and energy collection time history analysis of the adjacent building coupled with the optimum design parameter TIDs were carried out.It was found that TID had a better damping effect in the full-time range compared with the classic TMD.This paper also studied the potential power of TID in adjacent buildings,which can be converted into available power resources during earthquakes.

Phase evolution of 17(Cu-10Ni)-(NiFe_2O_4-10NiO) cermet inert anode during aluminum electrolysis

17（Cu-10Ni）-（NiFe2O4-10NiO） cermets were prepared by cold pressing and sintering in nitrogen atmosphere, and tested as inert anode for aluminum electrolysis at 960 °C for 10 and 40 h, respectively. Microstructures and phase compositions of the as-sintered and post-electrolyzed samples were investigated. The impurity contents in the electrolyte and the cathode metal were detected in order to investigate the corrosion characteristic of the elements of Fe, Ni and Cu in the anode. A dense NiFe2O4 layer was observed on the surface of anode and thickened with prolonging the electrolysis time. In the newly formed dense ceramic layer, NiO phase disappeared as a result of being swallowed by NiFe2O4 phase, and the metal phase was oxidized during the electrolysis in which Cu element showed a higher dissolution rate than Fe and Ni elements. The formation process of the dense ceramic layer during the electrolysis was presented and explained by using the corrosion mode of the metal phase and the transformation mechanism from NiO phase to NiFe2O4 phase.

Effect of additive BaO on corrosion resistance of xCu/(10NiO-NiFe_2O_4) cermet inert anodes for aluminum electrolysis

xCu/（10NiO-NiFe2O4） cermet and 1BaO-xCu/（10NiO-NiFe2O4） cermet（x=5,10,17） inert anodes were prepared as potential inert anodes for aluminum electrolysis and their corrosion resistance to traditional electrolyte was studied with anodic current density of 1.0 A/cm2 in laboratory electrolysis.The substantial corrosion of metal Cu was observed,many pores appeared on the surface of anode and electrolytes infiltrated inside anodes during the electrolysis.The wear rates of 5Cu/（10NiO-NiFe2O4）,10Cu/（10NiO-NiFe2O4）,17Cu/（10NiO-NiFe2O4）,1BaO-5Cu/（10NiO-NiFe2O4）,1BaO-10Cu/（10NiO-NiFe2O4） and 1BaO-17Cu/（10NiO-NiFe2O4） are 2.15,6.50,8.30,4.88,4.70 and 4.48 cm/a,respectively.The addition of BaO to 10Cu/（10NiO-NiFe2O4） cermet and 17Cu/（10NiO-NiFe2O4） cermet is advantageous because BaO can effectively promote densification and thus improve corrosion resistance.But the addition of BaO to 5Cu/（10NiO-NiFe2O4） cermet is unfavorable to corrosion resistance because additive BaO at the grain boundary of anode accelerates possibly the corrosion of cermet.

Effect of sintering atmosphere on corrosion resistance of Ni/(NiFe_2O_4-10NiO) cermet inert anode for aluminum electrolysis

A comparative study on the corrosion resistance of 17Ni/（NiFe2O4-10NiO） cermet inert anode prepared in differentsintering atmospheres was conducted in Na3AlF6-Al2O3 melt. The results indicate that the corrosion rates of NiFe2O4-based cermetanodes prepared in the vacuum and the atmosphere with oxygen content of 2×10^-3 （volume fraction） are 6.46 and 2.71 cm/a,respectively. Though there is a transition layer with lots of holes or pores, a densified layer is formed on the surface of anode due tosome reactions producing aluminates. For the anode prepared in the atmosphere with oxygen content of 2×10^-3, the thickness of thedensification layer （about 50 μm） is thicker than that （about 30 μm） formed on the surface of anode prepared in the vacuum. Thecontents of NiO and Fe（II） in NiFe2xO4-y-z increase with the decrease of oxygen content in sintering atmosphere, which reduces thecorrosion resistance of the material.

Corrosion of NiFe_2O_4-10NiO-based cermet inert anodes for aluminium electrolysis

NiFe2O4-10NiO-based cermet inert anodes for aluminium electrolysis were prepared and their properties were investigated in a lab-scale electrolysis cell. The results show that the inert anodes exhibit good performance during electrolysis in molten salt cryolite at 960 °C, but according to the analyses of phase compositions and microstructures through XRD, SEM/EDX and metallographic analysis, the metal in the anodes is preferentially corroded and many pores are produced on the anode surface after electrolysis. The preferential dissolution of Fe in the NiFe2O4 phase may lead to the non-uniform corrosion of NiFe2O4 grains. Moreover, a dense protective layer of NiFe2O4-NiAl2O4-FeAl2O4 is formed on the anode surface, which originates from the reaction of Al2O3 dissolved in the electrolyte with NiO or FeO, the annexation of NiFe2O4-NiAl2O4-FeAl2O4 to NiO and volume expansion. Thus, the dense NiFe2O4-NiAl2O4-FeAl2O4 layer inhibits the metal loss and ceramic-phase corrosion on the surface of the cermet inert anodes.

Effects of polyaniline on electrochemical properties of composite inert anodes used in zinc electrowinning

In order to search for a suitable anode material used in zinc electrowinning in place of Pb-Ag alloy,Al/Pb-PANI（polyaniline）-WC（tungsten carbide） composite inert anodes were prepared on aluminum alloy substrate by double pulse electrodeposition（DPE） of PANI and WC particles with Pb2＋ from an original plating bath.Thereafter,anodic polarization curves,cyclic voltammetry curves and Tafel polarization curves for the composite inert anodes obtained under different PANI concentrations in the original plating bath were measured,and the microstructural features were also investigated by scanning electron microscopy（SEM）.The results show that Al/Pb-PANI-WC composite inert anode obtained under PANI concentration of 20 g/L in the original plating bath possesses uniform microstructures and composition distributions,higher electrocatalytic activity,better reversibility of electrode reaction and corrosion resistance in a synthetic zinc electrowinning electrolyte of 50 g/L Zn2＋,150 g/L H2SO4 at 35 °C.Compared with Pb-1%Ag alloy,the overpotential of oxygen evolutions for the composite inert anode are decreased by 185 mV and 166 mV,respectively,under 500 A/m2 and 1000 A/m2.

From Unmanned Systems to Autonomous Intelligent Systems

1.Introduction Artificial intelligence(AI)is a rapidly growing field of technol-ogy,which“will enliven inert objects,much as electricity did more than a century ago.Everything that we formerly electrified will now cognitize”[1].AI advances are constantly pushing the frontier of what machines can do.Increased attention is being placed on AI research,as well as its development and deployment by commer-cial investors,defense strategists,and policy makers[2].

Synthetic LiFePO4/C without using inert gas

LiFePO4/C was synthesized by high temperature solid-state method with cheap Fe2O3, LiH2PO4 and glucose as raw materials in absence of inert gas. The sample had ordered olivine-type structure other impurities characterized by the test of X-ray diffraction （XRD）. The charge-discharge test showed the sample could demonstrate 120.5 mAh/g at 0.2C rate with good cyclic capability. The powder microeleetrode cyclic voltammetry test indicated that the redox process of the sample had good reversibility.

EFFECT OF Cu-Ni CONTENT ON THE CORROSION RESISTANCE OF(Cu-Ni)/(10NiO-90NiFe_2O_4)CERMET INERT ANODE FOR ALUMINUM ELECTROLYSIS

（Cu-Ni）/（10NiO-90NiFe204） cermet inert anodes containing metal Cu-Ni0, 5, 10, 15 and 20 wt pct were prepared and their corrosion resistance to Na3AlF6-Al2O3 melts was investigated. The results indicate that the content of metal Cu-Ni has little effect on the steady-state concentration of Ni in the electrolyte and the values could not be used to effectively differentiate their corrosion resistance. The steady-state concentration of Fe decreases from 304×10^-6 to 168×10^-6 and that of Cu increases from 21×10^-6 to 71×10^-6 with the content of metal Cu-Ni increasing from 0 to 20 wt pct. Post-examination shows that metallic phase Cu-Ni is corroded preferentially during electrolysis and many pores are left at the anode surface. Considering the corrosion resistance and electrical conductivity, the cermet containing metal Cu-Ni 5 wt pct should be selected and studied further.

Microstructure and mechanical characteristics of AA6061-T6 joints produced by friction stir welding,friction stir vibration welding and tungsten inert gas welding:A comparative study

This study compared the microstructure and mechanical characteristics of AA6061-T6 joints produced using friction stir welding(FSW),friction stir vibration welding(FSVW),and tungsten inert gas welding(TIG).FSVW is a modified version of FSW wherein the joining specimens are vibrated normal to the welding line during FSW.The results indicated that the weld region grains for FSVW and FSW were equiaxed and were smaller than the grains for TIG.In addition,the weld region grains for FSVW were finer compared with those for FSW.Results also showed that the strength,hardness,and toughness values of the joints produced by FSVW were higher than those of the other joints produced by FSW and TIG.The vibration during FSW enhanced dynamic recrystallization,which led to the development of finer grains.The weld efficiency of FSVW was approximately 81%,whereas those of FSW and TIG were approximately 74%and 67%,respectively.

EFFECT OF STRUCTURAL PARAMETERS ON THE THERMAL STRESS OF A NiFe_(2)O_(4)-BASED CERMET INERT ANODE IN ALUMINUM ELECTROLYSIS

Inert anode has been a hot issue in the aluminum industry for many decades. With the help of FEA （finite element analysis） software ANSYS, a model was developed to simulate the thermal stress distribution working condition of an inert anode. To reduce its thermal stress, the effect of some parameters on the thermal stress distribution was investigated, including the anode height, the anode radius, the hole depth, the hole radius, and the radius of inner chamfer and outer chamfer. The results showed that in the actual working condition of an inert anode, there existed a large axial tensile stress near the tangent interface between the anode and bath, which was the major cause of anode breaking. Increasing the anode height and reducing the hole depth properly seemed to be beneficial for the stress distribution. With the increase of anode radius, the stress distribution became better first and then deteriorated, the reasonable value was between 0.045 to 0.06m. The hole radius had a significant effect on the stress and a smaller radius would reduce the thermal stress. The effect of the radius of the inner chamfer and the outer chamfer was less than other parameters.

Liquation cracking in the heat-affected zone of IN939 superalloy tungsten inert gas weldments

The main aim of this study was to investigate liquation cracking in the heat-affected zone(HAZ)of the IN939 superalloy upon tungsten inert gas welding.A solid solution and age-hardenable filler metals were further studied.On the pre-weld heat-treated samples,upon solving the secondaryγ′particles in the matrix,primaryγ′particles in the base metal grew to"ogdoadically diced cubes"of about 2μm in side lengths.The pre-weld heat treatment reduced the hardness of the base metal to about HV 310.Microstructural studies using optical and fieldemission scanning electron microscopy revealed that the IN939 alloy was susceptible to liquation cracking in the HAZ.The constitutional melting of the secondary,eutectic,and Zr-rich phases promoted the liquation cracking in the HAZ.The microstructure of the weld fusion zones showed the presence of fine spheroidalγ′particles with sizes of about 0.2μm after the post-weld heat treatment,which increased the hardness of the weld pools to about HV 350 and 380 for the Hastelloy X and IN718 filler metals,respectively.Application of a suitable solid solution filler metal could partially reduce the liquation cracking in the HAZ of IN939 alloy.

Optimal design and effectiveness evaluation for inerter-based devices on mitigating seismic responses of base isolated structures

The optimal design and effectiveness of three control systems,tuned viscous mass damper(TVMD),tuned inerter damper(TID)and tuned mass damper(TMD),on mitigating the seismic responses of base isolated structures,were systematically studied.First,the seismic responses of the base isolated structure with each control system under white noise excitation were obtained.Then,the structural parameter optimizations of the TVMD,TID and TMD were conducted by using three different objectives.The results show that the three control systems were all effective in minimizing the root mean square value of seismic responses,including the base shear of the BIS,the absolute acceleration of structural SDOF,and the relative displacement between the base isolation floor and the foundation.Finally,considering the superstructure as a structural MDOF,a series of time history analyses were performed to investigate the effectiveness and activation sensitivity of the three control systems under far field and near fault seismic excitations.The results show that the effectiveness of TID and TMD with optimized parameters on mitigating the seismic responses of base isolated structures increased as the mass ratio increases,and the effectiveness of TID was always better than TMD with the same mass ratio.The TVMD with a lower mass ratio was more efficient in reducing the seismic response than the TID and TMD.Furthermore,the TVMD,when compared with TMD and TID,had better activation sensitivity and a smaller stroke.

Microstructure and mechanical properties of friction pull plug welding for2219-T87 aluminum alloy with tungsten inert gas weld

The friction pull plug welding(FPPW)of the 2219-T87 tungsten inert gas(TIG)welded joint was investigated,and the microstructures,precipitate evolution,mechanical properties,and fracture morphologies of this joint were analyzed and discussed.In this study,defectfree joints were obtained using a rotational speed of 7000 r/min,an axial feeding displacement of 12 mm,and an axial force of 20-22 kN.The results indicated that within these welding parameters,metallurgical bonding between the plug and plate is achieved by the formation of recrystallized grains.The microstructural features of the FPPW joint can be divided into different regions,including the heat-affected zone(HAZ),thermomechanically affected zone(TMAZ),recrystallization zone(RZ),heat-affected zone in the TIG weld(TIG-HAZ),and the thermomechanically affected zone in the TIG weld(TIG-TMAZ).In the TIG-TMAZ,the grains were highly deformed and elongated due to the shear and the extrusion that produces the plug during the FPPW process.The main reason for the softening in the TMAZ is determined to be the dissolution ofθ’and coarsening ofθprecipitate particles.In a tensile test,the FPPW joint welded with an axial force of 22 kN showed the highest ultimate tensile strength of 237 MPa.The locations of cracks and factures in the TIG-TMAZ were identified.The fracture morphology of the tensile sample showed good plasticity and toughness of the joints.