This article lists all possible conversion equations of influence coefficients(ICs)with different formats when some of these are known to handle two-plane balancing tasks with no or less trial weight runs.There are tw...This article lists all possible conversion equations of influence coefficients(ICs)with different formats when some of these are known to handle two-plane balancing tasks with no or less trial weight runs.There are two approaches for two-plane balancing.One can treat it as a multi-plane balance problem involving a 2×2 matrix of complex ICs where two direct ICs along with two cross-effect ICs are generated so that correction weights at one or two balance planes can be determined.One can also apply a static pare(in-phase)and/or couple pair(180 degrees out-of-phase)weights for balancing.The latter approach has been used quite often in the field,especially on steam turbine and generator rotors.Dependent on vibration mode shapes and combinations as well as balance plane accessibility,sometimes applying static or couple pair weights can be a wise choice;other times weights at one or two end planes are needed.There are totally 4 possible sets of IC data due to weights at plane 1,plane 2,static pair,and couple pair.IC data would typically be obtained by applying trial weights followed by trial weight runs.It is found,however,that all these IC data can be converted easily without trial weight runs once any two of 4 sets are known.The above findings and conversion equations have been obtained analytically and verified by experimental results.Real cases are given to demonstratetheirapplications.展开更多
Measurement error of unbalance's vibration response plays a crucial role in calibration and on-line updating of influence coefficient(IC). Focusing on the two problems that the moment estimator of data used in cali...Measurement error of unbalance's vibration response plays a crucial role in calibration and on-line updating of influence coefficient(IC). Focusing on the two problems that the moment estimator of data used in calibration process cannot fulfill the accuracy requirement under small sample and the disturbance of measurement error cannot be effectively suppressed in updating process, an IC calibration and on-line updating method based on hierarchical Bayesian method for automatic dynamic balancing machine was proposed. During calibration process, for the repeatedly-measured data obtained from experiments with different trial weights, according to the fact that measurement error of each sensor had the same statistical characteristics, the joint posterior distribution model for the true values of the vibration response under all trial weights and measurement error was established. During the updating process, information obtained from calibration was regarded as prior information, which was utilized to update the posterior distribution of IC combined with the real-time reference information to implement online updating. Moreover, Gibbs sampling method of Markov Chain Monte Carlo(MCMC) was adopted to obtain the maximum posterior estimation of parameters to be estimated. On the independent developed dynamic balancing testbed, prediction was carried out for multiple groups of data through the proposed method and the traditional method respectively, the result indicated that estimator of influence coefficient obtained through the proposed method had higher accuracy; the proposed updating method more effectively guaranteed the measurement accuracy during the whole producing process, and meantime more reasonably compromised between the sensitivity of IC change and suppression of randomness of vibration response.展开更多
Based on the model structure of the influence coefficient method analyzed in depth by matrix theory,it is explained the reason why the unreasonable and instable correction masses with bigger MSE are obtained by LS inf...Based on the model structure of the influence coefficient method analyzed in depth by matrix theory,it is explained the reason why the unreasonable and instable correction masses with bigger MSE are obtained by LS influence coefficient method when there are correlation planes in the dynamic balancing.It also presened the new ridge regression method for solving correction masses according to the Tikhonov regularization theory,and described the reason why the ridge regression can eliminate the disadvantage of the LS method. Applying this new method to dynamic balancing of gas turbine, it is found that this method is superior to the LS method when influence coefficient matrix is ill-conditioned,the minimal correction masses and residual vibration are obtained in the dynamic balancing of rotors.展开更多
Typical rotors such as those on steam turbine or generator are often supported by two bearings with two balance planes at both ends.Vibrations are monitored by a pair of proximity probes at each bearing.There are two ...Typical rotors such as those on steam turbine or generator are often supported by two bearings with two balance planes at both ends.Vibrations are monitored by a pair of proximity probes at each bearing.There are two approaches to reduce 1X vibration due to unbalance at both ends via balancing with influence coefficient method.The first approach is to treat it as a multiple-plane balancing problem involving 2x2 matrix of complex influence coefficients.The second approach is to treat it as two single-plane balance problems using static(in-phase)and couple(180 degree out-of-phase)components,respectively.Conversion equations of influence coefficients between these two approaches have been found previously by the author.The corresponding spreadsheets that convert influence coefficients between these two formats are presented in the current paper.The paper shows effectiveness of these conversion equations in dealing with real balancing problems in the field.A detailed balance case is presented to demonstrate how the conversion equations are used to reduce vibration effectively.展开更多
The influence of the pressure transmission medium(PTM)on the excitonic interband transitions in monolayer tungsten diselenide(WSe2)is investigated using photoluminescence(PL)spectra under hydrostatic pressure up...The influence of the pressure transmission medium(PTM)on the excitonic interband transitions in monolayer tungsten diselenide(WSe2)is investigated using photoluminescence(PL)spectra under hydrostatic pressure up to 5GPa.Three kinds of PTMs,condensed argon(Ar),1:1 n-pentane and isopentane mixture(PM),and4:1 methanol and ethanol mixture(MEM,a PTM with polarity),are used.It is found that when either Ar or PM is used as the PTM,the PL peak of exciton related to the direct K-K interband transition shows a pressure-induced blue-shift at a rate of 32±4 or 32±1 meV/GPa,while it turns to be 50±9meV/GPa when MEM is used as the PTM.The indirect A-K interband transition presents almost no shift with increasing pressure up to approximatel.y 5 GPa when Ar and PM are used as the PTM,while it shows a red-shift at the rate of-17±7meV/GPa by using MEM as the PTM.These results reveal that the optical interband transitions of monolayer WSe2 are very sensitive to the polarity of the PTM.The anomalous pressure coefficient obtained using the polar PTM of MEM is ascribed to the existence of hydrogen-like bonds between hydroxyl in MEM and Se atoms under hydrostatic pressure.展开更多
Due to the diversity of work requirements and environment,the number of degrees of freedom(DOFs)and the complexity of structure of industrial robots are constantly increasing.It is difficult to establish the accurate ...Due to the diversity of work requirements and environment,the number of degrees of freedom(DOFs)and the complexity of structure of industrial robots are constantly increasing.It is difficult to establish the accurate dynamical model of industrial robots,which greatly hinders the realization of a stable,fast and accurate trajectory tracking control.Therefore,the general expression of the constraint relation in the explicit dynamic equation of the multi-DOF industrial robot is derived on the basis of solving the Jacobian matrix and Hessian matrix by using the kinematic influence coefficients method.Moreover,an explicit dynamic equation with general constraint relation expression is established based on the Udwadia-Kalaba theory.The problem of increasing the time of establishing constraint relationship when the multi-DOF industrial robots complete complex task constraints is solved.With the SCARA robot as the research object,the simulation results show that the proposed method can provide a new idea for industrial robot system modeling with complex constraints.展开更多
Seismic analysis of buried pipes has been one study focus during the last decades,but the systematic seismic research of pipe connections,especially its relationship with the connected straight pipe,is nearly blank.On...Seismic analysis of buried pipes has been one study focus during the last decades,but the systematic seismic research of pipe connections,especially its relationship with the connected straight pipe,is nearly blank.On the basis,the influence of pipe connections on the joint deformations(JDs)of buried segmented pipes is analyzed in detail by considering different parameters,namely,connection shapes,ground conditions,pipe diameters,branch angles,seismic incident angles,and input ground motions.Moreover,an influence coefficient,which measures the influence of pipe connections on pipe JDs,is calculated.Results show that pipe connections can reduce the JDs of segmented pipes by 40%-50%.Furthermore,the JD is more sensitive to the connection shape,ground condition and pipe diameter than the incident angle and characteristics of seismic waves.An influence coefficient of 0.65 is recommended conservatively for the design of the buried segmented pipes.展开更多
Software for calculating the strip profile in 4-high hot rolling mill was developed using influence coefficient method. Regularity of backup roller diameter effect rate was studied systematically using the software. T...Software for calculating the strip profile in 4-high hot rolling mill was developed using influence coefficient method. Regularity of backup roller diameter effect rate was studied systematically using the software. The results show that backup roller diameter effect rates decrease versus the increase of strip width, increase significantly versus the increase of backup roller diameter and obscurely increase versus the increase of reduction. The difference between backup roller diameter effect rate and it is reference value increases versus strip width increasing. When backup rollers diameter is set to be 1.64 m and strip width is 1.85 m, the error of strip profile calculated using the model of backup roller diameter effect rate reference value will be 3.55μm. Based on the results, reference values of roller diameter effect rate and six power polynomial fitting coefficients of modification coefficients were determined considering coherent parameters. The high precision model of backup roller diameter effect rate was established. When the model is used to predict strip profile, the accuracy is less than 5.0 μm.展开更多
To study simultaneous location of different kinds of facilities, a new model of flow interception problem with multi-type of flows is proposed, with the consideration of multi-purpose flows and the influence of facili...To study simultaneous location of different kinds of facilities, a new model of flow interception problem with multi-type of flows is proposed, with the consideration of multi-purpose flows and the influence of facilities on each other. To be more practical, the objective is to maximize the benefits from flow-by customers instead of maximizing flows in the past. Since this problem is NP-hard and there is no optimal solution for large network, greedy and improved greedy heuristic algorithms are proposed. A computational example is presented to show that the optimal location decisions are proved to be strongly dependent on the influence coefficients and average profits by one customer and different types of facilities are almost co-located. Finally the results of sensitivity analysis are reported.展开更多
The primary emphasis of this research was to investigate the foundations of phthalate(PAEs) pollutant source researches and then firstly confirmed the concept of the coefficient of volatile strength, namely phthalat...The primary emphasis of this research was to investigate the foundations of phthalate(PAEs) pollutant source researches and then firstly confirmed the concept of the coefficient of volatile strength, namely phthalate total content in per unit mass and unit surface area of pollutant sources. Through surveying and evaluating the coefficient of volatile strength of PAEs from typical plastic products, this research carried out reasonable classification of PAEs pollutant sources into three categories and then investigated the relationship amongst the coefficient of volatile strength as well as other environmental factors and the concentration level of total PAEs in indoor air measured in environment chambers.Research obtained phthalate concentration results under different temperature, humidity,the coefficient of volatile strength and the closed time through the chamber experiment. In addition, this study further explored the correlation and ratio of influencing factors that affect the concentration level of total PAEs in environment chambers, including environmental factors, the coefficient of volatile strengths of PAEs and contents of total PAEs in plastic products. The research created an improved database system of phthalate the coefficient of volatile strengths of each type of plastic goods, and tentatively revealed that the volatile patterns of PAEs from different typical plastic goods, finally confirmed that the coefficient of volatile strengths of PAEs is a major factor that affects the indoor air total PAEs concentration, which laid a solid foundation for further establishing the volatile equation of PAEs from plastic products.展开更多
This study proposed a force and shape collaborative control method that combined method of influence coefficients(MIC)and the elitist nondominated sorting genetic algorithm(NSGA-II)to reduce the shape deviation caused...This study proposed a force and shape collaborative control method that combined method of influence coefficients(MIC)and the elitist nondominated sorting genetic algorithm(NSGA-II)to reduce the shape deviation caused by manufacturing errors,gravity deformation,and fixturing errors and improve the shape accuracy of the assembled large composite fuselage panel.This study used a multi-point flexible assembly system driven by hexapod parallel robots.The proposed method simultaneously considers the shape deviation and assembly load of the panel.First,a multi-point flexible assembly system driven by hexapod parallel robots was introduced,with the relevant variables defined in the control process.In addition,the corresponding mathematical model was constructed.Subsequently,MIC was used to establish the prediction models between the displacements of actuators and displacements of panel shape control points,deformation loads applied by the actuators.Following the modeling,the shape deviation of the panel and the assembly load were used as the optimization objectives,and the displacements of actuators were optimized using NSGA-II.Finally,a typical composite fuselage panel case study was considered to demonstrate the effectiveness of the proposed method.展开更多
In order to research the shear behavior of glass fiber reinforced polymer (GFRP) reinforced concrete beam with circular cross section, based on the test results of 36 concrete beams subjected to four-point loading up ...In order to research the shear behavior of glass fiber reinforced polymer (GFRP) reinforced concrete beam with circular cross section, based on the test results of 36 concrete beams subjected to four-point loading up to failure, the shear capacity and mechanical properties of deformation were analyzed comparatively between GFRP reinforced concrete (GFRP-RC) beams and steel reinforced concrete (steel-RC) beams. Furthermore, influencing factors of shear capacity of GFRP-RC beam with circular cross section were also investigated. The test results indicate that the failure modes of GFRP-RC and steel-RC beams are the same, but the crack patterns are slightly different. And, the shear capacity of GFRP-RC beam firstly increases with the reduction of shear span ratio, and then decreases. In addition, it was found that the influencing coefficient of GFRP on concrete increases with shear span ratio reducing.展开更多
A balancing method without trial weights based on the dynamic similitude scale model was proposed as a solution to the balancing problem of a large-scale rotor system. This method could be used to directly obtain the ...A balancing method without trial weights based on the dynamic similitude scale model was proposed as a solution to the balancing problem of a large-scale rotor system. This method could be used to directly obtain the required coefficients for the balancing problem of the prototype system through a similarity model test without a prototype test. Thus, the weight test process of the prototype system was effectively eliminated in the proposed balancing method. First, with the rotor system as the research object, the analytical expression of the influence coefficient was derived on the basis of rotor dynamics theory. Then, through calculation and dimen- sional analysis methods, the similitude relationships of the rotor system and the influence coefficient were deduced on the basis of dynamic similitude theory. The correctness of the proposed similitude relationships was verified through numerical simulation and experiment. The balancing method without trial weights was proposed based on the similitude relationship of the influence coefficient. The effect of the balancing method without trial weights was compared with that of the traditional influence coefficient method through numerical simulation, and the results verified the correctness and effectiveness of the proposed balancing method. The results of this study provide theoretical supplements for the balancing method and the similitude design of the rotor system.展开更多
A Reduced Order Model(ROM)based analysis method for turbomachinery cascade coupled mode flutter is presented in this paper.The unsteady aerodynamic model is established by a system identification technique combined wi...A Reduced Order Model(ROM)based analysis method for turbomachinery cascade coupled mode flutter is presented in this paper.The unsteady aerodynamic model is established by a system identification technique combined with a set of Aerodynamic Influence Coefficients(AIC).Subsequently,the aerodynamic model is encoded into the state space and then coupled with the structural dynamic equations,resulting in a ROM of the cascade aeroelasticity.The cascade flutter can be determined by solving the eigenvalues of the ROM.Bending-torsional coupled mode flutter analysis for the Standard Configuration Eleven(SC11)cascade is used to validate the proposed method.展开更多
Proposed in the paper is a trigonometric interpolation method for efficient determination of turbomachinery blade aero-damping curves which are required in a flutter assessment.The trigonometric interpolation method w...Proposed in the paper is a trigonometric interpolation method for efficient determination of turbomachinery blade aero-damping curves which are required in a flutter assessment.The trigonometric interpolation method was proposed to be incorporated with the widely used travelling wave method to replace the influence coefficient method.Through analyzing aero-damping/worksum at a few carefully chosen nodal diameters,trigonometric interpolation was applied through existing data points to get aero-damping/worksum at the rest nodal diameters.The proposed approach is much more efficient than the travelling wave method for determining the aero-damping curve of a blade.In principle,the method can be as efficient as the influence coefficient method.Unlike the influence coefficient method,the trigonometric interpolation method does not involve linear superposition,and it can include nonlinear effect and is expected to be more accurate.Two test cases were provided to validate the proposed method and demonstrate its effectiveness.The method is not only effective,but also very easy to be incorporated into existing widely used aero-damping/worksum analysis system using the travelling wave method.展开更多
Conclusion is that the soft threshold de-noising effect is better than hard threshold de-noising though the signal to noise ratio and Root Mean Square error. After analyzing, de-noising and reconstructing signal throu...Conclusion is that the soft threshold de-noising effect is better than hard threshold de-noising though the signal to noise ratio and Root Mean Square error. After analyzing, de-noising and reconstructing signal through wavelet packet from Matlab software, the average value of peak extracted from signal reconstruction is gotten to provide data for dynamic balance. Making use of the influence coefficient method to adjust drum of CTP dynamic balance, the program of Matlab is used to find phase position and weight of the mass block quickly, which can provide evidence for software for dynamic balance developed.展开更多
In this research, the temperatures of three- dimensional (3D) protruding heaters mounted on a conductive substrate in a horizontal rectangular channel with laminar airflow are related to the independent power dissip...In this research, the temperatures of three- dimensional (3D) protruding heaters mounted on a conductive substrate in a horizontal rectangular channel with laminar airflow are related to the independent power dissipation in each heater by using a matrix G+ with invariant coefficients, which are dimensionless. These coefficients are defined in this study as the conjugate influence coefficients (g+) caused by the forced convec- tion-conduction nature of the heaters' cooling process. The temperature increase of each heater in the channel is quantified to clearly identify the contributions attributed to the self-heating and power dissipation in the other heaters (both upstream and downstream). The conjugate coefficients are invariant with the heat generation rate in the array of heaters when assuming a defined geometry, invariable fluid and flow rate, and constant substrate and heater conductivities. The results are numerically obtained by considering three 3D protruding heaters on a twodimensional (2D) array by ANSYS/FluentTM 15.0 software. The conservation equations are solved by a coupled procedure within a single calculation domain comprising of solid and fluid regions and by considering a steady state laminar airflow with constant properties. Some examples are shown, indicating the effects of substrate thermal conductivity and Reynolds number on conjugate influence coefficients.展开更多
Based on the influence coefficient method, the effect of entry strip crown on the shape of hot rolled strip was analyzed using the software of roll elastic deformation simulation. According to the practical condition ...Based on the influence coefficient method, the effect of entry strip crown on the shape of hot rolled strip was analyzed using the software of roll elastic deformation simulation. According to the practical condition of a domestic hot rolled strip plant, the unit strip crown change from the first stand to the last stand was calculated when the entry crown of hot strip varies. The calculated result shows that the entry strip crown does not significantly affect the target strip crown at the exit of the last finishing stand in respect to a fixed strip shape control reference (such as bending force). The calculation was analyzed, and the research is helpful in modeling strip shape setup and shape control.展开更多
文摘This article lists all possible conversion equations of influence coefficients(ICs)with different formats when some of these are known to handle two-plane balancing tasks with no or less trial weight runs.There are two approaches for two-plane balancing.One can treat it as a multi-plane balance problem involving a 2×2 matrix of complex ICs where two direct ICs along with two cross-effect ICs are generated so that correction weights at one or two balance planes can be determined.One can also apply a static pare(in-phase)and/or couple pair(180 degrees out-of-phase)weights for balancing.The latter approach has been used quite often in the field,especially on steam turbine and generator rotors.Dependent on vibration mode shapes and combinations as well as balance plane accessibility,sometimes applying static or couple pair weights can be a wise choice;other times weights at one or two end planes are needed.There are totally 4 possible sets of IC data due to weights at plane 1,plane 2,static pair,and couple pair.IC data would typically be obtained by applying trial weights followed by trial weight runs.It is found,however,that all these IC data can be converted easily without trial weight runs once any two of 4 sets are known.The above findings and conversion equations have been obtained analytically and verified by experimental results.Real cases are given to demonstratetheirapplications.
基金supported by National Hi-tech Research and Development Program of China (863 Program, Grant No. 2008 AA04Z114)
文摘Measurement error of unbalance's vibration response plays a crucial role in calibration and on-line updating of influence coefficient(IC). Focusing on the two problems that the moment estimator of data used in calibration process cannot fulfill the accuracy requirement under small sample and the disturbance of measurement error cannot be effectively suppressed in updating process, an IC calibration and on-line updating method based on hierarchical Bayesian method for automatic dynamic balancing machine was proposed. During calibration process, for the repeatedly-measured data obtained from experiments with different trial weights, according to the fact that measurement error of each sensor had the same statistical characteristics, the joint posterior distribution model for the true values of the vibration response under all trial weights and measurement error was established. During the updating process, information obtained from calibration was regarded as prior information, which was utilized to update the posterior distribution of IC combined with the real-time reference information to implement online updating. Moreover, Gibbs sampling method of Markov Chain Monte Carlo(MCMC) was adopted to obtain the maximum posterior estimation of parameters to be estimated. On the independent developed dynamic balancing testbed, prediction was carried out for multiple groups of data through the proposed method and the traditional method respectively, the result indicated that estimator of influence coefficient obtained through the proposed method had higher accuracy; the proposed updating method more effectively guaranteed the measurement accuracy during the whole producing process, and meantime more reasonably compromised between the sensitivity of IC change and suppression of randomness of vibration response.
文摘Based on the model structure of the influence coefficient method analyzed in depth by matrix theory,it is explained the reason why the unreasonable and instable correction masses with bigger MSE are obtained by LS influence coefficient method when there are correlation planes in the dynamic balancing.It also presened the new ridge regression method for solving correction masses according to the Tikhonov regularization theory,and described the reason why the ridge regression can eliminate the disadvantage of the LS method. Applying this new method to dynamic balancing of gas turbine, it is found that this method is superior to the LS method when influence coefficient matrix is ill-conditioned,the minimal correction masses and residual vibration are obtained in the dynamic balancing of rotors.
文摘Typical rotors such as those on steam turbine or generator are often supported by two bearings with two balance planes at both ends.Vibrations are monitored by a pair of proximity probes at each bearing.There are two approaches to reduce 1X vibration due to unbalance at both ends via balancing with influence coefficient method.The first approach is to treat it as a multiple-plane balancing problem involving 2x2 matrix of complex influence coefficients.The second approach is to treat it as two single-plane balance problems using static(in-phase)and couple(180 degree out-of-phase)components,respectively.Conversion equations of influence coefficients between these two approaches have been found previously by the author.The corresponding spreadsheets that convert influence coefficients between these two formats are presented in the current paper.The paper shows effectiveness of these conversion equations in dealing with real balancing problems in the field.A detailed balance case is presented to demonstrate how the conversion equations are used to reduce vibration effectively.
基金Supported by the National Key Research and Development Program of China under Grant No 2016YFA0301202the National Natural Science Foundation of China under Grant Nos 11474275,61674135 and 91536101+1 种基金the Strategic Priority Research Program of the Chinese Academy of Sciences under Grant No XDPB0603the China Postdoctoral Science Foundation under Grant No 2017M622400
文摘The influence of the pressure transmission medium(PTM)on the excitonic interband transitions in monolayer tungsten diselenide(WSe2)is investigated using photoluminescence(PL)spectra under hydrostatic pressure up to 5GPa.Three kinds of PTMs,condensed argon(Ar),1:1 n-pentane and isopentane mixture(PM),and4:1 methanol and ethanol mixture(MEM,a PTM with polarity),are used.It is found that when either Ar or PM is used as the PTM,the PL peak of exciton related to the direct K-K interband transition shows a pressure-induced blue-shift at a rate of 32±4 or 32±1 meV/GPa,while it turns to be 50±9meV/GPa when MEM is used as the PTM.The indirect A-K interband transition presents almost no shift with increasing pressure up to approximatel.y 5 GPa when Ar and PM are used as the PTM,while it shows a red-shift at the rate of-17±7meV/GPa by using MEM as the PTM.These results reveal that the optical interband transitions of monolayer WSe2 are very sensitive to the polarity of the PTM.The anomalous pressure coefficient obtained using the polar PTM of MEM is ascribed to the existence of hydrogen-like bonds between hydroxyl in MEM and Se atoms under hydrostatic pressure.
基金the Beijing Municipal Scienceand Technology Project (No.KM202111417006)the Academic Research Projects of Beijing Union University (Nos.ZK10202305 and ZK80202004)the Beijing Municipal Science and Technology Project (No.KM202111417005)。
文摘Due to the diversity of work requirements and environment,the number of degrees of freedom(DOFs)and the complexity of structure of industrial robots are constantly increasing.It is difficult to establish the accurate dynamical model of industrial robots,which greatly hinders the realization of a stable,fast and accurate trajectory tracking control.Therefore,the general expression of the constraint relation in the explicit dynamic equation of the multi-DOF industrial robot is derived on the basis of solving the Jacobian matrix and Hessian matrix by using the kinematic influence coefficients method.Moreover,an explicit dynamic equation with general constraint relation expression is established based on the Udwadia-Kalaba theory.The problem of increasing the time of establishing constraint relationship when the multi-DOF industrial robots complete complex task constraints is solved.With the SCARA robot as the research object,the simulation results show that the proposed method can provide a new idea for industrial robot system modeling with complex constraints.
基金from the National Key Research and Development Program of China(Grant No.2016YFC0802400)is greatly appreciatedsupported by the Ministry of Science and Technology of China(Grant No.2016YFC0802400).
文摘Seismic analysis of buried pipes has been one study focus during the last decades,but the systematic seismic research of pipe connections,especially its relationship with the connected straight pipe,is nearly blank.On the basis,the influence of pipe connections on the joint deformations(JDs)of buried segmented pipes is analyzed in detail by considering different parameters,namely,connection shapes,ground conditions,pipe diameters,branch angles,seismic incident angles,and input ground motions.Moreover,an influence coefficient,which measures the influence of pipe connections on pipe JDs,is calculated.Results show that pipe connections can reduce the JDs of segmented pipes by 40%-50%.Furthermore,the JD is more sensitive to the connection shape,ground condition and pipe diameter than the incident angle and characteristics of seismic waves.An influence coefficient of 0.65 is recommended conservatively for the design of the buried segmented pipes.
基金the National Natu-ral Science Foundation of China,under the contract No.59995440the State Key Development Prograrmming Research under the contract No.G2000027208-4 the Natural Science Foundation ofLiaoning Province,under the contract No.2001101021.
文摘Software for calculating the strip profile in 4-high hot rolling mill was developed using influence coefficient method. Regularity of backup roller diameter effect rate was studied systematically using the software. The results show that backup roller diameter effect rates decrease versus the increase of strip width, increase significantly versus the increase of backup roller diameter and obscurely increase versus the increase of reduction. The difference between backup roller diameter effect rate and it is reference value increases versus strip width increasing. When backup rollers diameter is set to be 1.64 m and strip width is 1.85 m, the error of strip profile calculated using the model of backup roller diameter effect rate reference value will be 3.55μm. Based on the results, reference values of roller diameter effect rate and six power polynomial fitting coefficients of modification coefficients were determined considering coherent parameters. The high precision model of backup roller diameter effect rate was established. When the model is used to predict strip profile, the accuracy is less than 5.0 μm.
基金supported by the National Natural Science Foundation of China(7060101170871044)Trans-Century Traning Program Foundation for the Talents by the State Education Commission(NECT-06-0653).
文摘To study simultaneous location of different kinds of facilities, a new model of flow interception problem with multi-type of flows is proposed, with the consideration of multi-purpose flows and the influence of facilities on each other. To be more practical, the objective is to maximize the benefits from flow-by customers instead of maximizing flows in the past. Since this problem is NP-hard and there is no optimal solution for large network, greedy and improved greedy heuristic algorithms are proposed. A computational example is presented to show that the optimal location decisions are proved to be strongly dependent on the influence coefficients and average profits by one customer and different types of facilities are almost co-located. Finally the results of sensitivity analysis are reported.
基金support by the National Key Technologies R&D Program (No. 2016YFC0207103)Koninklijke Philips N.V.Brainbridge Cooperation Agreement (Grant Number BB3-2016-01)
文摘The primary emphasis of this research was to investigate the foundations of phthalate(PAEs) pollutant source researches and then firstly confirmed the concept of the coefficient of volatile strength, namely phthalate total content in per unit mass and unit surface area of pollutant sources. Through surveying and evaluating the coefficient of volatile strength of PAEs from typical plastic products, this research carried out reasonable classification of PAEs pollutant sources into three categories and then investigated the relationship amongst the coefficient of volatile strength as well as other environmental factors and the concentration level of total PAEs in indoor air measured in environment chambers.Research obtained phthalate concentration results under different temperature, humidity,the coefficient of volatile strength and the closed time through the chamber experiment. In addition, this study further explored the correlation and ratio of influencing factors that affect the concentration level of total PAEs in environment chambers, including environmental factors, the coefficient of volatile strengths of PAEs and contents of total PAEs in plastic products. The research created an improved database system of phthalate the coefficient of volatile strengths of each type of plastic goods, and tentatively revealed that the volatile patterns of PAEs from different typical plastic goods, finally confirmed that the coefficient of volatile strengths of PAEs is a major factor that affects the indoor air total PAEs concentration, which laid a solid foundation for further establishing the volatile equation of PAEs from plastic products.
基金supported by National Natural Science Foundation of China(No.52105502)Fund of National Engineering and Research Center for Commercial Aircraft Manufacturing(Nos.COMAC-SFGS-2019-263 and COMAC-SFGS-2019-3731)the Fundamental Research Funds for the Central Universities(No.3042021601).
文摘This study proposed a force and shape collaborative control method that combined method of influence coefficients(MIC)and the elitist nondominated sorting genetic algorithm(NSGA-II)to reduce the shape deviation caused by manufacturing errors,gravity deformation,and fixturing errors and improve the shape accuracy of the assembled large composite fuselage panel.This study used a multi-point flexible assembly system driven by hexapod parallel robots.The proposed method simultaneously considers the shape deviation and assembly load of the panel.First,a multi-point flexible assembly system driven by hexapod parallel robots was introduced,with the relevant variables defined in the control process.In addition,the corresponding mathematical model was constructed.Subsequently,MIC was used to establish the prediction models between the displacements of actuators and displacements of panel shape control points,deformation loads applied by the actuators.Following the modeling,the shape deviation of the panel and the assembly load were used as the optimization objectives,and the displacements of actuators were optimized using NSGA-II.Finally,a typical composite fuselage panel case study was considered to demonstrate the effectiveness of the proposed method.
基金the National Natural Science Foundation of China (No.51078318)the Program for New Century Excellent Talents in University (No.10-0667)the Fundamental Research Funds for the Central Universities (No.SWJTU09CX006)
文摘In order to research the shear behavior of glass fiber reinforced polymer (GFRP) reinforced concrete beam with circular cross section, based on the test results of 36 concrete beams subjected to four-point loading up to failure, the shear capacity and mechanical properties of deformation were analyzed comparatively between GFRP reinforced concrete (GFRP-RC) beams and steel reinforced concrete (steel-RC) beams. Furthermore, influencing factors of shear capacity of GFRP-RC beam with circular cross section were also investigated. The test results indicate that the failure modes of GFRP-RC and steel-RC beams are the same, but the crack patterns are slightly different. And, the shear capacity of GFRP-RC beam firstly increases with the reduction of shear span ratio, and then decreases. In addition, it was found that the influencing coefficient of GFRP on concrete increases with shear span ratio reducing.
基金Acknowledgements This work was supported by the National Natural Science Foundation of China (Grant No. 11572082), the Excellent Talents Support Program in Institutions of Higher Learning in Liaoning Province of China (Grant No. LJQ2015038), and the Fundamental Research Funds for the Central Universities of China (Grant Nos. N160312001, N150304004, and N140301001).
文摘A balancing method without trial weights based on the dynamic similitude scale model was proposed as a solution to the balancing problem of a large-scale rotor system. This method could be used to directly obtain the required coefficients for the balancing problem of the prototype system through a similarity model test without a prototype test. Thus, the weight test process of the prototype system was effectively eliminated in the proposed balancing method. First, with the rotor system as the research object, the analytical expression of the influence coefficient was derived on the basis of rotor dynamics theory. Then, through calculation and dimen- sional analysis methods, the similitude relationships of the rotor system and the influence coefficient were deduced on the basis of dynamic similitude theory. The correctness of the proposed similitude relationships was verified through numerical simulation and experiment. The balancing method without trial weights was proposed based on the similitude relationship of the influence coefficient. The effect of the balancing method without trial weights was compared with that of the traditional influence coefficient method through numerical simulation, and the results verified the correctness and effectiveness of the proposed balancing method. The results of this study provide theoretical supplements for the balancing method and the similitude design of the rotor system.
基金supported by the National Science and Technology Major Project, China (No. 2017-II-0009-0023)the Aeronautical Science Foundation of China(No. 2020Z039053004)the Fundamental Research Funds for the Central Universities, China (No. 3102019OQD701)
文摘A Reduced Order Model(ROM)based analysis method for turbomachinery cascade coupled mode flutter is presented in this paper.The unsteady aerodynamic model is established by a system identification technique combined with a set of Aerodynamic Influence Coefficients(AIC).Subsequently,the aerodynamic model is encoded into the state space and then coupled with the structural dynamic equations,resulting in a ROM of the cascade aeroelasticity.The cascade flutter can be determined by solving the eigenvalues of the ROM.Bending-torsional coupled mode flutter analysis for the Standard Configuration Eleven(SC11)cascade is used to validate the proposed method.
基金supported by China’s 111 project(Grant No.B17037)National Natural Science Foundation of China(Grant No.51976172)National Science and Technology Major Project(2017-II-0009-0023)。
文摘Proposed in the paper is a trigonometric interpolation method for efficient determination of turbomachinery blade aero-damping curves which are required in a flutter assessment.The trigonometric interpolation method was proposed to be incorporated with the widely used travelling wave method to replace the influence coefficient method.Through analyzing aero-damping/worksum at a few carefully chosen nodal diameters,trigonometric interpolation was applied through existing data points to get aero-damping/worksum at the rest nodal diameters.The proposed approach is much more efficient than the travelling wave method for determining the aero-damping curve of a blade.In principle,the method can be as efficient as the influence coefficient method.Unlike the influence coefficient method,the trigonometric interpolation method does not involve linear superposition,and it can include nonlinear effect and is expected to be more accurate.Two test cases were provided to validate the proposed method and demonstrate its effectiveness.The method is not only effective,but also very easy to be incorporated into existing widely used aero-damping/worksum analysis system using the travelling wave method.
文摘Conclusion is that the soft threshold de-noising effect is better than hard threshold de-noising though the signal to noise ratio and Root Mean Square error. After analyzing, de-noising and reconstructing signal through wavelet packet from Matlab software, the average value of peak extracted from signal reconstruction is gotten to provide data for dynamic balance. Making use of the influence coefficient method to adjust drum of CTP dynamic balance, the program of Matlab is used to find phase position and weight of the mass block quickly, which can provide evidence for software for dynamic balance developed.
文摘In this research, the temperatures of three- dimensional (3D) protruding heaters mounted on a conductive substrate in a horizontal rectangular channel with laminar airflow are related to the independent power dissipation in each heater by using a matrix G+ with invariant coefficients, which are dimensionless. These coefficients are defined in this study as the conjugate influence coefficients (g+) caused by the forced convec- tion-conduction nature of the heaters' cooling process. The temperature increase of each heater in the channel is quantified to clearly identify the contributions attributed to the self-heating and power dissipation in the other heaters (both upstream and downstream). The conjugate coefficients are invariant with the heat generation rate in the array of heaters when assuming a defined geometry, invariable fluid and flow rate, and constant substrate and heater conductivities. The results are numerically obtained by considering three 3D protruding heaters on a twodimensional (2D) array by ANSYS/FluentTM 15.0 software. The conservation equations are solved by a coupled procedure within a single calculation domain comprising of solid and fluid regions and by considering a steady state laminar airflow with constant properties. Some examples are shown, indicating the effects of substrate thermal conductivity and Reynolds number on conjugate influence coefficients.
文摘Based on the influence coefficient method, the effect of entry strip crown on the shape of hot rolled strip was analyzed using the software of roll elastic deformation simulation. According to the practical condition of a domestic hot rolled strip plant, the unit strip crown change from the first stand to the last stand was calculated when the entry crown of hot strip varies. The calculated result shows that the entry strip crown does not significantly affect the target strip crown at the exit of the last finishing stand in respect to a fixed strip shape control reference (such as bending force). The calculation was analyzed, and the research is helpful in modeling strip shape setup and shape control.