This work mainly focuses on the mineralogical study of particulate matter（PM10） in Beijing. Samples were collected on polycarbonate filter from April, 2002 to March, 2003 in Beijing urban area. Scanning electronic m...This work mainly focuses on the mineralogical study of particulate matter（PM10） in Beijing. Samples were collected on polycarbonate filter from April, 2002 to March, 2003 in Beijing urban area. Scanning electronic microscopy coupled with energy dispersive X-ray（SEM/EDX） was used to investigate individual mineral particles in Beijing PM10. 1454 individual mineral particulates from 48 samples were analysed by SEM/EDX. The results revealed that mineral particulates were complex and heterogeneous. 38 kinds of minerals in PM10 were identified. The clay minerals, of annual average percentage of 30.1%, were the main composition among the identified minerals, and illite/smectite was the main composition in clay minerals, reaching up to 35%. Annual average percentage of quartz, calcite, compound particulates, carbonates were 13.5%, 10.9%, 11.95%, 10.31%, respectively. Annual average percentage less than 10% were gypsum, feldspar, dolomite, and so on. Fluorite, apatite, halite, barite and chloridize zinc（ZnCl2） were firstly identified in Beijing PM10. Sulfurization was found on surface of mineral particles, suggested extensive atmospheric reaction in air during summer.展开更多
The Brussels Capital Region has difficulties in meeting the stringent EU daily limit value for PM10 in all its measuring sites. Postponing the attainment of the deadline was not granted by the EU Commission, mainly du...The Brussels Capital Region has difficulties in meeting the stringent EU daily limit value for PM10 in all its measuring sites. Postponing the attainment of the deadline was not granted by the EU Commission, mainly due to insufficient judged measures to reduce road traffic emissions. However, a thorough analysis of the data makes clear that neither the particle mass concentration (PM10 and PM2.5) nor the particle number concentration are specific metrics for evaluating the particle pollution originated by traffic. In fact, increased formation of secondary aerosol, together with adverse meteorological conditions and the (re) suspension of the coarser fraction are by far the three main explanations for the numerous PM10 exceeding values. From our experience, amongst the particles measured, only the results for Black Carbon (BC), mainly present in the lower submicron range, are reflective of the direct influence of local traffic. Measured at two traffic sites along with PM mass and number concentrations, the data for Black Carbon show a striking correlation with nitrogen monoxide, a parameter strongly related with the proximity of the local traffic. The correlation factor between Black Carbon data and NO or NOX is much higher than between Black Carbon and the PM mass or number concentration. Therefore the assessment of traffic related particles should consider Black Carbon rather than PM10 or PM2.5.展开更多
Despite international efforts to limit worker exposure to coal dust,it continues to impact the health of thousands of miners across Europe.Airborne coal dust has been studied to improve risk models and its control to ...Despite international efforts to limit worker exposure to coal dust,it continues to impact the health of thousands of miners across Europe.Airborne coal dust has been studied to improve risk models and its control to protect workers.Particle size distribution analyses shows that using spraying systems to suppress airborne dusts can reduce particulate matter concentrations and that coals with higher ash yields produce finer dust.There are marked chemical differences between parent coals and relatively coarse deposited dusts(up to _(500)μm,DD_(500)).Enrichments in Ca,K,Ba,Se,Pb,Cr,Mo,Ni and especially As,Sn,Cu,Zn and Sb in the finest respirable dust fractions could originate from:(i)mechanical machinery wear;(ii)variations in coal mineralogy;(iii)coal fly ash used in shotcrete,and carbonates used to reduce the risk of explosions.Unusual enrichments in Ca in mine dusts are attributed to the use of such concrete,and elevated K to raised levels of phyllosilicate mineral matter.Sulphur concentrations are higher in the parent coal than in the DD_(500),probably due to relatively lower levels of organic matter.Mass concentrations of all elements observed in this study remained below occupational exposure limits.展开更多
The Tongon mine, the largest gold mine in C?te d’Ivoire, has been in operation since April 2010. However, to our knowledge to date, no study has been conducted on metallic contamination in suspended particulate matte...The Tongon mine, the largest gold mine in C?te d’Ivoire, has been in operation since April 2010. However, to our knowledge to date, no study has been conducted on metallic contamination in suspended particulate matter (PM<sub>10</sub> and PM<sub>2.5</sub>) where there is a lack of information on the carcinogenic and non-carcinogenic risk to human health associated with the exposure of populations in the Tongon area to these pollutants. The general objective of this study is to evaluate the level of contamination of PM<sub>10</sub>;PM<sub>2.5</sub> by heavy metals and their impact on the health of populations exposed to these pollutants in the Tongon gold mine area. The sampling and measurement of suspended particulate matter (PM<sub>10</sub> and PM<sub>2.5</sub>) were done using a MiniVol TAS passive air sampler. Heavy metal concentrations were determined by inductively coupled plasma mass spectroscopy (Nex ION 2000 ICP-MS, USA). The results indicate that the average concentrations of suspended particles (PM<sub>2.5</sub> and PM<sub>10</sub>) obtained are all above the recommended exposure limits. In addition, among the heavy metals contained in the suspended particles, the concentrations of arsenic and nickel are high and all above the standard limit values. The assessment of the health risks related to the inhalation of PM<sub>10</sub> particles reveals that their inhalation over a long period could cause a carcinogenic risk.展开更多
Incense smoke(IS)is source of indoor air pollution and key risk for diverse human diseases.Less in-formation is available regarding controlled IS rodent inhalation exposure system and IS particulate matter(PM)depositi...Incense smoke(IS)is source of indoor air pollution and key risk for diverse human diseases.Less in-formation is available regarding controlled IS rodent inhalation exposure system and IS particulate matter(PM)deposition in human airways.Study aimed to demonstrate stable ISPM physicochemical parameters of 10 incense products inside the customized whole body inhalation exposure chamber(without animal)connected to smoke generation unit via aerosol mixing device.IS analyzed for size segregated PM emission,ISPM in vitro aerodynamics(MMAD and GSD determination),fine and ultrafine particle's SEM,SEM-EDX and PAH analysis.Using real life exposure scenario by utilizing MMAD,GSD and PM concentration after Tier 1 exposure assessment as key input parameters,ISPM dosimetry in infant(3 months)and adult(21 years male and female)human airways was calculated using multiple-path particle dosimetry(MPPD 3.04)modeling.Mass median aerodynamic diameter(MMAD)and geo-metric standard deviation(GSD)ranged between 0.55 and 2.10μm and 1.22 to 1.77(polydisperse)respectively.PM1.0 and PM0.1 showed multiple morphology and presence of heavy and trace elements.PAH like acenaphthylene,anthracene,fluorene,naphthalene and phenanthrene were detected(0.84-143.17μg/g).MPPD results showed higher ISPM deposition in pulmonary region and lowest in trachea bronchial region.ISPM deposition in tissue was higher in lower,peripheral lung as compared to upper and central lung tissue.Whole body inhalation exposure system showed stable IS atmosphere(physi-cochemical parameters)indicating the device suitability in future inhalation studies.MPPD ISPM deposition fraction and clearance data showed deep lung penetrating and retention behavior with higher risk in infant followed by female and then male.These modeled particle deposition and clearance data may be useful in risk assessment analysis of IS.展开更多
采用成都市可吸入颗粒物(PM10)小时浓度的空间分布实例,结合NOAA/AVHRR(National Oceanic and Atmospheric Administration/Advanced Very High Resolution Radiometer)遥感数据所获的城市热岛温度场格局图,结果发现:下午环形热岛出现...采用成都市可吸入颗粒物(PM10)小时浓度的空间分布实例,结合NOAA/AVHRR(National Oceanic and Atmospheric Administration/Advanced Very High Resolution Radiometer)遥感数据所获的城市热岛温度场格局图,结果发现:下午环形热岛出现时城市中心区的PM10浓度较低,二、三环路附近的浓度相对较高,城区西南部尤其明显。分析认为,环形热岛改变了城市近地层的温度场和流场结构,在城郊结合部造成"双重循环",容易导致污染物在这些地方聚集。展开更多
基金The National Natural Science Foundation of China（No.40275040） and the Shanghai Leading Academic Disciplines（No. T0105）
文摘This work mainly focuses on the mineralogical study of particulate matter（PM10） in Beijing. Samples were collected on polycarbonate filter from April, 2002 to March, 2003 in Beijing urban area. Scanning electronic microscopy coupled with energy dispersive X-ray（SEM/EDX） was used to investigate individual mineral particles in Beijing PM10. 1454 individual mineral particulates from 48 samples were analysed by SEM/EDX. The results revealed that mineral particulates were complex and heterogeneous. 38 kinds of minerals in PM10 were identified. The clay minerals, of annual average percentage of 30.1%, were the main composition among the identified minerals, and illite/smectite was the main composition in clay minerals, reaching up to 35%. Annual average percentage of quartz, calcite, compound particulates, carbonates were 13.5%, 10.9%, 11.95%, 10.31%, respectively. Annual average percentage less than 10% were gypsum, feldspar, dolomite, and so on. Fluorite, apatite, halite, barite and chloridize zinc（ZnCl2） were firstly identified in Beijing PM10. Sulfurization was found on surface of mineral particles, suggested extensive atmospheric reaction in air during summer.
文摘The Brussels Capital Region has difficulties in meeting the stringent EU daily limit value for PM10 in all its measuring sites. Postponing the attainment of the deadline was not granted by the EU Commission, mainly due to insufficient judged measures to reduce road traffic emissions. However, a thorough analysis of the data makes clear that neither the particle mass concentration (PM10 and PM2.5) nor the particle number concentration are specific metrics for evaluating the particle pollution originated by traffic. In fact, increased formation of secondary aerosol, together with adverse meteorological conditions and the (re) suspension of the coarser fraction are by far the three main explanations for the numerous PM10 exceeding values. From our experience, amongst the particles measured, only the results for Black Carbon (BC), mainly present in the lower submicron range, are reflective of the direct influence of local traffic. Measured at two traffic sites along with PM mass and number concentrations, the data for Black Carbon show a striking correlation with nitrogen monoxide, a parameter strongly related with the proximity of the local traffic. The correlation factor between Black Carbon data and NO or NOX is much higher than between Black Carbon and the PM mass or number concentration. Therefore the assessment of traffic related particles should consider Black Carbon rather than PM10 or PM2.5.
基金European Commission Research Fund for Coal and Steel(Grant Agreement Number–754205)Generalitat de Catalunya(SGR41).Centre of Excellence Severo Ochoa—Spanish Ministry of Science and Innovation(Project CEX2018-000794-S).
文摘Despite international efforts to limit worker exposure to coal dust,it continues to impact the health of thousands of miners across Europe.Airborne coal dust has been studied to improve risk models and its control to protect workers.Particle size distribution analyses shows that using spraying systems to suppress airborne dusts can reduce particulate matter concentrations and that coals with higher ash yields produce finer dust.There are marked chemical differences between parent coals and relatively coarse deposited dusts(up to _(500)μm,DD_(500)).Enrichments in Ca,K,Ba,Se,Pb,Cr,Mo,Ni and especially As,Sn,Cu,Zn and Sb in the finest respirable dust fractions could originate from:(i)mechanical machinery wear;(ii)variations in coal mineralogy;(iii)coal fly ash used in shotcrete,and carbonates used to reduce the risk of explosions.Unusual enrichments in Ca in mine dusts are attributed to the use of such concrete,and elevated K to raised levels of phyllosilicate mineral matter.Sulphur concentrations are higher in the parent coal than in the DD_(500),probably due to relatively lower levels of organic matter.Mass concentrations of all elements observed in this study remained below occupational exposure limits.
文摘The Tongon mine, the largest gold mine in C?te d’Ivoire, has been in operation since April 2010. However, to our knowledge to date, no study has been conducted on metallic contamination in suspended particulate matter (PM<sub>10</sub> and PM<sub>2.5</sub>) where there is a lack of information on the carcinogenic and non-carcinogenic risk to human health associated with the exposure of populations in the Tongon area to these pollutants. The general objective of this study is to evaluate the level of contamination of PM<sub>10</sub>;PM<sub>2.5</sub> by heavy metals and their impact on the health of populations exposed to these pollutants in the Tongon gold mine area. The sampling and measurement of suspended particulate matter (PM<sub>10</sub> and PM<sub>2.5</sub>) were done using a MiniVol TAS passive air sampler. Heavy metal concentrations were determined by inductively coupled plasma mass spectroscopy (Nex ION 2000 ICP-MS, USA). The results indicate that the average concentrations of suspended particles (PM<sub>2.5</sub> and PM<sub>10</sub>) obtained are all above the recommended exposure limits. In addition, among the heavy metals contained in the suspended particles, the concentrations of arsenic and nickel are high and all above the standard limit values. The assessment of the health risks related to the inhalation of PM<sub>10</sub> particles reveals that their inhalation over a long period could cause a carcinogenic risk.
文摘Incense smoke(IS)is source of indoor air pollution and key risk for diverse human diseases.Less in-formation is available regarding controlled IS rodent inhalation exposure system and IS particulate matter(PM)deposition in human airways.Study aimed to demonstrate stable ISPM physicochemical parameters of 10 incense products inside the customized whole body inhalation exposure chamber(without animal)connected to smoke generation unit via aerosol mixing device.IS analyzed for size segregated PM emission,ISPM in vitro aerodynamics(MMAD and GSD determination),fine and ultrafine particle's SEM,SEM-EDX and PAH analysis.Using real life exposure scenario by utilizing MMAD,GSD and PM concentration after Tier 1 exposure assessment as key input parameters,ISPM dosimetry in infant(3 months)and adult(21 years male and female)human airways was calculated using multiple-path particle dosimetry(MPPD 3.04)modeling.Mass median aerodynamic diameter(MMAD)and geo-metric standard deviation(GSD)ranged between 0.55 and 2.10μm and 1.22 to 1.77(polydisperse)respectively.PM1.0 and PM0.1 showed multiple morphology and presence of heavy and trace elements.PAH like acenaphthylene,anthracene,fluorene,naphthalene and phenanthrene were detected(0.84-143.17μg/g).MPPD results showed higher ISPM deposition in pulmonary region and lowest in trachea bronchial region.ISPM deposition in tissue was higher in lower,peripheral lung as compared to upper and central lung tissue.Whole body inhalation exposure system showed stable IS atmosphere(physi-cochemical parameters)indicating the device suitability in future inhalation studies.MPPD ISPM deposition fraction and clearance data showed deep lung penetrating and retention behavior with higher risk in infant followed by female and then male.These modeled particle deposition and clearance data may be useful in risk assessment analysis of IS.
文摘采用成都市可吸入颗粒物(PM10)小时浓度的空间分布实例,结合NOAA/AVHRR(National Oceanic and Atmospheric Administration/Advanced Very High Resolution Radiometer)遥感数据所获的城市热岛温度场格局图,结果发现:下午环形热岛出现时城市中心区的PM10浓度较低,二、三环路附近的浓度相对较高,城区西南部尤其明显。分析认为,环形热岛改变了城市近地层的温度场和流场结构,在城郊结合部造成"双重循环",容易导致污染物在这些地方聚集。
