Heat transfer enhanced inorganic phase change material compositing carbon nanotubes for battery thermal management and thermal runaway propagation mitigation

Developing technologies that can be applied simultaneously in battery thermal management(BTM)and thermal runaway(TR)mitigation is significant to improving the safety of lithium-ion battery systems.Inorganic phase change material(PCM)with nonflammability has the potential to achieve this dual function.This study proposed an encapsulated inorganic phase change material(EPCM)with a heat transfer enhancement for battery systems,where Na_(2)HPO_(4)·12H_(2)O was used as the core PCM encapsulated by silica and the additive of carbon nanotube(CNT)was applied to enhance the thermal conductivity.The microstructure and thermal properties of the EPCM/CNT were analyzed by a series of characterization tests.Two different incorporating methods of CNT were compared and the proper CNT adding amount was also studied.After preparation,the battery thermal management performance and TR propagation mitigation effects of EPCM/CNT were further investigated on the battery modules.The experimental results of thermal management tests showed that EPCM/CNT not only slowed down the temperature rising of the module but also improved the temperature uniformity during normal operation.The peak battery temperature decreased from 76℃to 61.2℃at 2 C discharge rate and the temperature difference was controlled below 3℃.Moreover,the results of TR propagation tests demonstrated that nonflammable EPCM/CNT with good heat absorption could work as a TR barrier,which exhibited effective mitigation on TR and TR propagation.The trigger time of three cells was successfully delayed by 129,474 and 551 s,respectively and the propagation intervals were greatly extended as well.

Exploration of Ideological and Political Materials for the Course of Inorganic and Analytical Chemistry for Environmental and Ecological Engineering Major

Integrating ideological and political theories teaching into the whole process of classroom teaching construction is a new requirement for implementing the fundamental task of cultivating people by virtue and playing the role of collaborative education.In order to realize the seamless integration of inorganic and analytical chemistry courses and ideological and political education,this paper summarizes the current situation of ideological and political research on inorganic and analytical chemistry courses in three major databases in China(VIP,CNKI and Wanfang),and sorts out the knowledge points,ideological and political elements and educational goals according to the content of the course chapters,to provide a basic guarantee for the ideological and political education construction of the course.

Separation of Inorganic Anions Using Methacrylate-Based Monolithic Column Modified with Trimethylamine in Ion Chromatography Capillary System

Methacrylate-based monolithic column was prepared in fused-silica capillary (80 ′ 0.32 mm i.d.) by in situ polymerizetion reaction using glycidyl methacrylate as monomer;ethylene dimethacrylate as crosslinker;1-propanol, 1,4-butanediol, and water as porogenic solvents. The monolith matrix was modified with trimethylamine to create strong anion exchanger via ring opening reaction of epoxy groups. The morphology of the monolithic column was studied by using Scanning Electron Microscope (SEM). This column had good mechanical stability and permeability. The effects of various mobile phases for separation of inorganic anions were investigated. Iodate, bromate, nitrite, bromide, and nitrate were separated within 11 min using100 mMpotassium chloride as mobile phase and detected at 210 nm. This method showed good precision of retention time, acceptable linearity and good sensitivity. Under the optimum condition, the RSD of the retention time was in the range of 1.09%-1.75% (n = 6). The calibration curve showed linear relationships between the peak area and the concentration. The limits of detection (LOD) and the limits of quantitation (LOQ) were between 0.08-0.18 mM and 0.26-0.61 mM, respectively. This method was applied to the determination of inorganic anions in tap water and ground water samples.

Tailoring Practically Accessible Polymer/Inorganic Composite Electrolytes for All-Solid-State Lithium Metal Batteries:A Review

Solid-state electrolytes(SSEs)are widely considered the essential components for upcoming rechargeable lithium-ion batteries owing to the potential for great safety and energy density.Among them,polymer solid-state electrolytes(PSEs)are competitive candidates for replacing commercial liquid electrolytes due to their flexibility,shape versatility and easy machinability.Despite the rapid development of PSEs,their practical application still faces obstacles including poor ionic conductivity,narrow electrochemical stable window and inferior mechanical strength.Polymer/inorganic composite electrolytes(PIEs)formed by adding ceramic fillers in PSEs merge the benefits of PSEs and inorganic solid-state electrolytes(ISEs),exhibiting appreciable comprehensive properties due to the abundant interfaces with unique characteristics.Some PIEs are highly compatible with high-voltage cathode and lithium metal anode,which offer desirable access to obtaining lithium metal batteries with high energy density.This review elucidates the current issues and recent advances in PIEs.The performance of PIEs was remarkably influenced by the characteristics of the fillers including type,content,morphology,arrangement and surface groups.We focus on the molecular interaction between different components in the composite environment for designing high-performance PIEs.Finally,the obstacles and opportunities for creating high-performance PIEs are outlined.This review aims to provide some theoretical guidance and direction for the development of PIEs.

4‑Terminal Inorganic Perovskite/Organic Tandem Solar Cells Offer 22%Efficiency

After fast developing of single-junction perovskite solar cells and organic solar cells in the past 10 years,it is becoming harder and harder to improve their power conversion efficiencies.Tandem solar cells are receiving more and more attention because they have much higher theoretical efficiency than single-junction solar cells.Good device performance has been achieved for perovskite/silicon and perovskite/perovskite tandem solar cells,including 2-terminal and 4-terminal structures.However,very few studies have been done about 4-terminal inorganic perovskite/organic tandem solar cells.In this work,semi-transparent inorganic perovskite solar cells and organic solar cells are used to fabricate 4-terminal inorganic perovskite/organic tandem solar cells,achieving a power conversion efficiency of 21.25%for the tandem cells with spin-coated perovskite layer.By using drop-coating instead of spin-coating to make the inorganic perovskite films,4-terminal tandem cells with an efficiency of 22.34%are made.The efficiency is higher than the reported 2-terminal and 4-terminal inorganic perovskite/organic tandem solar cells.In addition,equivalent 2-terminal tandem solar cells were fabricated by connecting the sub-cells in series.The stability of organic solar cells under continuous illumination is improved by using semi-transparent perovskite solar cells as filter.

Inorganic Halide Perovskite Quantum Dots:A Versatile Nanomaterial Platform for Electronic Applications

Metal halide perovskites have generated significant attention in recent years because of their extraordinary physical properties and photovoltaic performance.Among these,inorganic perovskite quantum dots(QDs)stand out for their prominent merits,such as quantum confinement effects,high photoluminescence quantum yield,and defect-tolerant structures.Additionally,ligand engineering and an all-inorganic composition lead to a robust platform for ambient-stable QD devices.This review presents the state-of-the-art research progress on inorganic perovskite QDs,emphasizing their electronic applications.In detail,the physical properties of inorganic perovskite QDs will be introduced first,followed by a discussion of synthesis methods and growth control.Afterwards,the emerging applications of inorganic perovskite QDs in electronics,including transistors and memories,will be presented.Finally,this review will provide an outlook on potential strategies for advancing inorganic perovskite QD technologies.

Thixotropic composite hydrogels based on agarose and inorganic hybrid gellants

Water can be used as oxidant in conjunction with metal particles to form metal-water propellant to increase the energy of propellant.For this application,water needs to be stored in form of solid and capable of becoming liquid when use.Stable and thixotropic hydrogel has good potential as water-retaining material and oxidant of metal-based propellant.In this study,we prepared organic/inorganic composite hydrogels by combining inorganic gellants hectorite and fumed silica with organic gellant agarose,respectively.The total content of the gellants can be reduced to less than 2%by adding agarose.The influence of agarose on water content,phase transition temperature,centrifugal stability and other basic physical properties of composite hydrogels were discussed.The results show that the composite hydrogels have better thixotropy and stability than pure inorganic hydrogels,and the gel-sol transformation can be realized by applying shear force or heating to the phase transition temperature.The composite hydrogels have good shear thinning ability and improved mechanical stability.Fumed silica/agarose hydrogels have better physical stability,while the thixotropy and shear thinning ability of hectorite/agarose hydrogels are better.

Synergistic Optimization of Buried Interface by Multifunctional Organic-Inorganic Complexes for Highly Efficient Planar Perovskite Solar Cells

For the further improvement of the power conversion efficiency(PCE)and stability of perovskite solar cells(PSCs),the buried interface between the perovskite and the electron transport layer is crucial.However,it is challenging to effectively optimize this interface as it is buried beneath the perovskite film.Herein,we have designed and synthesized a series of multifunctional organic-inorganic(OI)complexes as buried interfacial material to promote electron extraction,as well as the crystal growth of the perovskite.The OI complex with BF4−group not only eliminates oxygen vacancies on the SnO_(2) surface but also balances energy level alignment between SnO_(2) and perovskite,providing a favorable environment for charge carrier extraction.Moreover,OI complex with amine(−NH_(2))functional group can regulate the crystallization of the perovskite film via interaction with PbI2,resulting in highly crystallized perovskite film with large grains and low defect density.Consequently,with rational molecular design,the PSCs with optimal OI complex buried interface layer which contains both BF4−and−NH_(2) functional groups yield a champion device efficiency of 23.69%.More importantly,the resulting unencapsulated device performs excellent ambient stability,maintaining over 90%of its initial efficiency after 2000 h storage,and excellent light stability of 91.5%remaining PCE in the maximum power point tracking measurement(under continuous 100 mW cm−2 light illumination in N2 atmosphere)after 500 h.

Stimuli-responsive nano-reserveriors drug delivery systems based on inorganic nanoparticles

The convergence of nanotechnology,material science,biology and medicine promotes the rapid development of nano-biomedicine,which plays an important role in relieving the pain of patients and improving the health of human,in particular of cancer therapy.Construction of stimuli-responsive controlled release system for targeted drug delivery to specific cells is essentially important for cancer therapy since most chemotherapeutics are severely toxic[1].During past decades,magnetic nanoparticles（MNPs）and mesoporous silica nanoparticles（MSNs）attracted much attention in the related field,due to their good biocompatibility。

MACROPROCESS OF PARTICLE FORMATION IN SUSPENSION POLYMERIZATION OF STYRENE WITH INORGANIC STABILIZER SYSTEM

The macroprocess of particle formation from suspension droplets of styrene in a pdymerizationsystem was investigated.Inorganic hydroxyapatite or its mixture with polyvinyl alcohol as thepolymerization system was used.Those items such as the effects of the Weight fraction of dispersed-phase,the amount of the inorganic stabilizer and the agitation speed on the breakup and coalescence of thetransient dispersed drops etc.Were examined.Results showd that the dynamic behavior of the transi-ent polymer droplets changed in the presence of the suspension stabilizer during the reaction.

Deposition of water-soluble inorganic ions in PM_(2.5) in a typical forestry system in Beijing,China

Background: Rapid economic development in China has resulted in an increase in severe air pollution in city groups such as the Beijing-Tianjin-Hebei Metropolitan Region. PM2.5(fine particles with an aerodynamic equivalent diameter of 2.5 [xm or less) is one of the most important pollutants. The deposition process is an important way of removing particles from the air. To evaluate the effect of an urban forest on atmospheric particle removal, a concentration gradient method was used to measure the deposition velocities of water-soluble inorganics in PM2.5 in two national forest parks in Beijing, China. The following eight water-soluble inorganic ions in PM2.5 were investigated: sodium, ammonium, potassium, magnesium, calcium, chloride, nitrate, and sulfate.Methods: Samples were taken from two sites in Beijing from the 7 th to the 15 th May, 2013. The concentrations of water-soluble inorganic ions were analyzed with ion chromatography. We used the concentration gradient technique to estimate the deposition flux and velocity. To determine the relationships between leaf traits and particle accumulation, typical leaf samples from each selected species were studied using scanning electron microscopy.Results: The total deposition flux and total deposition velocity during the daytime were higher than those at night.Sulfate showed the biggest deposition flux and velocity at both study sites, whereas the other ions showed different trends at each site. Result from higher proportion of coniferous to broadleaved trees, the total deposition flux of the eight ions measured in Jiufeng National Forest Park was greater than that in Olympic Forest Park.Conclusions: The deposition velocity was affected by meteorological conditions such as wind speed, temperature,and humidity. The deposition velocity was also influenced by tree species. The surface of plants is an important factor influencing particle deposition. The results of this study may help in assessing the effects of forestry systems on particle removal and provide evidence for urban air pollution control and afforestation of urban areas.

Assessment of System of Rice Intensification(SRI) and Conventional Practices under Organic and Inorganic Management in Japan

The system of rice intensification(SRI) is a production system that involves the adoption of certain changes in management practices for rice cultivation that create a better growing environment for the crop.This system was compared with conventional practices and assessed under organic and inorganic management.SRI practices showed significant response in root number,number of effective tillers per hill,days to flowering and harvest index.In addition,SRI was found effective in minimizing pest and disease incidence,shortening the crop cycle,and improving plant stand.Grain yield was not different from conventional method.Except for harvest index and plant lodging percentage,there were no significant effects from management treatments.Synergistic responses were noted when SRI practices were combined with organic management for plant height,number of effective tillers per hill,days to flowering and to maturity.The improved panicle characteristics,lower plant lodging percentage and higher harvest index that ultimately led to comparable grain yields.Net returns increased approximately 1.5 times for SRI-organic management regardless of the added labor requirements for weed control.However,comparatively higher grain yield from conventional-inorganic methods underscore the need for further investigations in defining what constitutes an optimum set of practices for an SRI-organic system specifically addressing grain yield and weed management.

Regulating Ecosystem Service (Filtering/ Immobilization of Inorganic Pollutants) Supplied by Soil in Model Regions of Slovakia

The immobilization of soil contaminants (as one of the regulating ecosystem services) plays very important role in environment. This regulatory service prevents groundwater contamination and the entry of contaminants into the food chain. The evaluation as well as the spatial distribution of this regulatory service is important for optimal land management in a specific region. Mapping system combining input layers—slope topography, soil texture, climate region and land use (arable land, grassland)—were created for the analysis and the evaluation of potential of agroecosystem services. Filtering potential was calculated as accumulative function of soil sorption potential and potential of total content of inorganic pollutants evaluated according to The Slovak Soil Law. Calculated potential was categorised into five categories: very low, low, medium, high and very high. Four model areas were selected for the analysis of pollutant filtration, as one of the regulatory agroecosystem services, which are located in different climatic areas and different soil-ecological conditions of Slovakia. The greatest differences among model regions can be found in relation to climatic conditions, land use and diversity of soil types. The warm, dry, and lowland region has a higher potential for pollutant filtration than the moderately warm or cold region. These results are consistent with the location of the soil, its properties, processes and functions within the concept of agro-ecosystem services. Based on the results, we can state that the high risk of inorganic contaminants is inherent in soils with low content and quality of organic substances, low pH value and high concentration of contaminants.

Interconnected and high cycling stability polypyrrole supercapacitors using cellulose nanocrystals and commonly used inorganic salts as dopants

Polypyrrole(PPy)is wildly used as electrode material in supercapacitors due to its high conductivity,low cost,ease of handling,and ease of fabrication.However,limited capacitance and poor cycling stability hinder its practical application.After developing carboxylated cellulose nanocrystals(CNC-COO^(-))as immobile dopants for PPy to improve its cycling stability,we investigated the effect of different commonly used salts(KCl,NaCl,KBr,and NaClO_(4))as dopants during electrode fabrication by electropolymerization.The film’s capacitance increased from 160.6 to 183.4 F g^(-1)after adding a combination of KCl and NaClO_(4) into the electrodeposition electrolyte.More importantly,the porous and interconnected PPy/CNC-COO^(-)-Cl-(Cl O_(4)^(-))_0.5 electrode film exhibited an excellent capacitance of 125.0 F g^(-1)(0.78 F cm^(-2))at a high current density of 2.0 Ag^(-1)(20 m A cm^(-2),allowing charging in less than 1 min),increasing almost 204%over PPy/CNC-COO-films.A symmetric PPy/CNC-COO^(-)-Cl-(ClO_(4)^(-))_0.5 supercapacitor retained its full capacitance after 5000 cycles,and displayed a high energy density of 5.2 Wh kg^(-1)at a power density of 25.4 W kg^(-1)(34.5μWh cm^(-2) at 1752.3μW cm^(-2)).These results reveal that the porous structure formed by doping with CNC-COO-and inorganic salts opens up more active reaction areas to store charges in PPy-based films as the stiff and ribbon-like CNC-COO-as permanent dopants improve the strength and stability of PPy-based films.Our demonstration provides a simple and practical way to deposit PPy based supercapacitors with high capacitance,fast charging,and excellent cycling stability.

Effect of inorganic salt on the thermal degradation of nitrocellulose and reaction mechanism of its mixture

In this study,to better understand the reaction mechanism between inorganic salts and nitrocellulose,CaCO_(3) and Li_(2)CO_(3) were evaluated with respect to their effects on the thermal degradation of NC in nitrogen atmosphere using TG/DSC at three different heating rates(2,5,10 K/min).The numerical relationship between activation energy(E)and conversion rate was obtained by FWO and KAS method,and it was discovered that CaCO_(3) could improve the thermal stability of NC.Activation energy values were calculated by Kissinger method,and it was found that NC that contain Li2CO3had the highest activation energy while NC containing CaCO3had the lowest E value.By combining the thermal analysis data with Malek method,the most probable mechanism model of thermal degradation is obtained as Sesták-Berggren model,which expression is f(α)=α^(m)(1-α)^(n).As a result of this study,there are certain guiding principles that can be applied to the pyrolysis reaction model and to the actual production process of nitrocellulose.

In Situ Formed Tribofilms as Efficient Organic/Inorganic Hybrid Interlayers for Stabilizing Lithium Metal Anodes

The practical application of Li metal anodes(LMAs)is limited by uncontrolled dendrite growth and side reactions.Herein,we propose a new friction-induced strategy to produce high-performance thin Li anode(Li@CFO).By virtue of the in situ friction reaction between fluoropolymer grease and Li strips during rolling,a robust organic/inorganic hybrid interlayer(lithiophilic LiF/LiC_(6)framework hybridized-CF_(2)-O-CF_(2)-chains)was formed atop Li metal.The derived interface contributes to reversible Li plating/stripping behaviors by mitigating side reactions and decreasing the solvation degree at the interface.The Li@CFO||Li@CFO symmetrical cell exhibits a remarkable lifespan for 5,600 h(1.0 mA cm^(-2)and 1.0 mAh cm^(-2))and 1,350 cycles even at a harsh condition(18.0 mA cm^(-2)and 3.0 mAh cm^(-2)).When paired with high-loading LiFePO4 cathodes,the full cell lasts over 450 cycles at 1C with a high-capacity retention of 99.9%.This work provides a new friction-induced strategy for producing high-performance thin LMAs.

Diatom-based dissolved inorganic nitrogen reconstruction in the Changjiang River estuary and its adjacent areas

A five-component weighted average partial least squares(WA-PLS)calibration model was developed by analysing diatom assemblages in 34 surface sediment samples(collected in 2015)from the Changjiang River estuary(CRE)and its adjacent areas to infer dissolved inorganic nitrogen(DIN)concentrations.Eighteen additional sets of surface sediment diatoms and corresponding upper water DIN data(collected in 2012)were used to evaluate the accuracy of the model,and the relationship between observed and diatom-inferred DIN(DI-DIN)values(R2=0.85)illustrated the strong performance of the transfer function,indicating that precise reconstructions of former DIN are possible.The diatom-DIN transfer function was applied to the diatom record from a sediment core DH8-2(1962‒2012)collected in the Fujian-Zhejiang area south of the CRE.The reconstruction based on the DI-DIN model showed a significant DIN increase from 1962-2012,reflecting the influence of human activities on the very large increase in eutrophication.Three distinct periods can be seen from the changes in DIN and diatom taxa.In the 1962-1972 period,the DIN content was relatively low,with an average of 5.94μmol/L,and more than 80%of the diatom species identified were benthic taxa.In the 1972-2004 period,as the impact of human activities intensified,large nutrient inputs caused the DIN content to increase,with an average of 8.25μmol/L.The nutrient inputs also caused a significant change in the nutrient components and a distinct increase in small planktonic taxa.In the 2004-2012 period,the DIN content continued to rise,fluctuating at approximately 10μmol/L.A continuous increase in the frequency of planktonic taxa(up to 65.48%)indicated that eutrophication was further intensified,which was confirmed by the transformation from diatom-induced red tide to dinoflagellate-induced red tide during this period.

A dual-mode image sensor using an all-inorganic perovskite nanowire array for standard and neuromorphic imaging

The high-density,vertically aligned retinal neuron array provides effective vision,a feature we aim to replicate with electronic devices.However,the conventional complementary metal-oxide-semiconductor(CMOS)image sensor,based on separate designs for sensing,memory,and processing units,limits its integration density.Moreover,redundant signal communication significantly increases energy consumption.Current neuromorphic devices integrating sensing and signal processing show promise in various computer vision applications,but there is still a need for frame-based imaging with good compatibility.In this study,we developed a dual-mode image sensor based on a high-density all-inorganic perovskite nanowire array.The device can switch between frame-based standard imaging mode and neuromorphic imaging mode by applying different biases.This unique bias-dependent photo response is based on a well-designed energy band diagram.The biomimetic alignment of nanowires ensures the potential for high-resolution imaging.To further demonstrate the imaging ability,we conducted pattern reconstruction in both modes with a 10×10 crossbar device.This study introduces a novel image sensor with high compatibility and efficiency,suitable for various applications including computer vision,surveillance,and robotics.

Dimethylammonium cation stabilizes all-inorganic perovskite solar cells

Facing the poor environmental stability of traditional methylammonium or formamidinium-based lead halide per-ovskites,scientists turn their attention to inorganic lead hal-ide perovskites(ILHPs)with narrow bandgaps,excellent thermal stability and reduced ion migration compared to their organic/inorganic counterparts[1−4].Up to now,the PCEs for ILHP solar cells exceed 21%[5].Especially,the preferred black ILHP(e.g.CsPbI3)with the smallest bandgap of~1.7 eV and single-halide composition for avoiding phase separation is crucial for high-performance single-junction solar cells and can be applied in tandem devices as the top cells[6,7].However,small Cs+(167 pm)in CsPbI3 with a tolerance factor close to 0.8 is unsuitable for the 3D PbI3-framework[8].The mis-matched size of cations will induce lattice strain and the per-ovskite spontaneously transforms to undesired non-photoact-ive yellow phase(δ-phase,like NH4CdCl3)(Fig.1(a))[9,10].There-fore,improving lattice symmetry and reducing lattice strain are the strategies for inhibiting the phase transition of ILHPs.

High-performance warm white LED based on thermally stable all inorganic perovskite quantum dots

All inorganic CsPbBr_(3) quantum dots(QDs)are regarded as excellent candidates for next-generation emitters due to their high photoluminescence quantum yield(PLQY)and defect tolerance.However,the poor stability and degraded luminescent performance may impede their further commercialization because of the separation of conventional ligands from the QDs surfaces.Recently,Zang replaced the regular oleic acid with 2-hexyl-decanoic acid(DA),which possesses higher binding energy on the QDs surfaces,to act as ligands of QDs,exhibiting PLQY of 96%and excellent stabilities against ethanol and water.WLEDs with DA-modified CsPbBr_(3) QDs achieved improved thermal stability,a color rendering index of 93,a power efficiency of 64.8 lm/W and a properly correlated color temperature value of 3018 K,implying their prominent applications in solid-state lighting and displays.