Gyrokinetic simulations of the kinetic electron effects on the electrostatic instabilities on the ITER baseline scenario

The linear and nonlinear simulations are carried out using the gyrokinetic code NLT for the electrostatic instabilities in the core region of a deuterium plasma based on the International Thermonuclear Experimental Reactor(ITER)baseline scenario.The kinetic electron effects on the linear frequency and nonlinear transport are studied by adopting the adiabatic electron model and the fully drift-kinetic electron model in the NLT code,respectively.The linear simulations focus on the dependence of linear frequency on the plasma parameters,such as the ion and electron temperature gradientsκ_(Ti,e)≡R=L_(Ti,e),the density gradientκ_(n)≡R/L_(n)and the ion-electron temperature ratioτ=T_(e)=T_(i).Here,is the major radius,and T_(e)and T_(i)denote the electron and ion temperatures,respectively.L_(A)=-(δ_(r)lnA)^(-1)is the gradient scale length,with denoting the density,the ion and electron temperatures,respectively.In the kinetic electron model,the ion temperature gradient(ITG)instability and the trapped electron mode(TEM)dominate in the small and large k_(θ)region,respectively,wherek_(θ)is the poloidal wavenumber.The TEMdominant region becomes wider by increasing(decreasing)κ_(T_(e))(κ_(T_(i)))or by decreasingκ_(n).For the nominal parameters of the ITER baseline scenario,the maximum growth rate of dominant ITG instability in the kinetic electron model is about three times larger than that in the adiabatic electron model.The normalized linear frequency depends on the value ofτ,rather than the value of T_(e)or T_(i),in both the adiabatic and kinetic electron models.The nonlinear simulation results show that the ion heat diffusivity in the kinetic electron model is quite a lot larger than that in the adiabatic electron model,the radial structure is finer and the time oscillation is more rapid.In addition,the magnitude of the fluctuated potential at the saturated stage peaks in the ITGdominated region,and contributions from the TEM(dominating in the higher k_(θ)region)to the nonlinear transport can be neglected.In the adiabatic electron model,the zonal radial electric field is found to be mainly driven by the turbulent energy flux,and the contribution of turbulent poloidal Reynolds stress is quite small due to the toroidal shielding effect.However,in the kinetic electron model,the turbulent energy flux is not strong enough to drive the zonal radial electric field in the nonlinear saturated stage.The kinetic electron effects on the mechanism of the turbulence-driven zonal radial electric field should be further investigated.

A novel responsive stabilizing Janus nanosilica as a nanoplugging agent in water-based drilling fluids for exploiting hostile shale environments

Thermo-responsive nanocomposites have recently emerged as potential nanoplugging agents for shale stabilization in high-temperature water-based drilling fluids(WBDFs). However, their inhibitory properties have not been very effective in high-temperature drilling operations. Thermo-responsive Janus nanocomposites are expected to strongly interact with clay particles from the inward hemisphere of nanomaterials, which drive the establishment of a tighter hydrophobic membrane over the shale surface at the outward hemisphere under geothermal conditions for shale stabilization. This work combines the synergistic benefits of thermo-responsive and zwitterionic nanomaterials to synchronously enhance the chemical inhibitions and plugging performances in shale under harsh conditions. A novel thermoresponsive Janus nanosilica(TRJS) exhibiting zwitterionic character was synthesized, characterized,and assessed as shale stabilizer for WBDFs at high temperatures. Compared to pristine nanosilica(Si NP)and symmetrical thermo-responsive nanosilica(TRS), TRJS exhibited anti-polyelectrolyte behaviour, in which electrolyte ions screened the electrostatic attraction between the charged particles, potentially stabilizing nanomaterial in hostile shaly environments(i.e., up to saturated brine or API brine). Macroscopically, TRJS exhibited higher chemical inhibition than Si NP and TRS in brine, prompting a better capability to control pressure penetration. TRJS adsorbed onto the clay surface via chemisorption and hydrogen bonding, and the interactions became substantial in brine, according to the results of electrophoretic mobility, surface wettability, and X-ray diffraction. Thus, contributing to the firm trapping of TRJS into the nanopore structure of the shale, triggering the formation of a tight hydrophobic membrane over the shale surface from the outward hemisphere. The addition of TRJS into WBDF had no deleterious effect on fluid properties after hot-treatment at 190℃, implying that TRJS could find potential use as a shale stabilizer in WBDFs in hostile environments.

Effects of Ca and Nd addition on plastic instability in extruded Mg-Mn alloy deformed under various conditions

Plastic instability, called Portevin-Le-Chatelier(PLC) effect, manifests itself as an unstable plastic flow during tensile tests of structural materials. This phenomenon has a strong influence on diverse properties, leading to unexpected vulnerabilities in the service environment.Among various magnesium-based alloys, PLC phenomenon is most prominently observed in the Mg-Mn-Nd alloy under elevated temperature and low strain rate conditions. An important aim of the study is to clarify and compare the significance of the RE and Ca addition, which are known to cause a formation of a largely weakened non-basal type texture, in the occurrence of plastic instability. Due to the PLC phenomenon, there is a risk of weakening texture and formability improvement by the addition of RE and Ca elements in Mg alloys. Based on the understanding of the role of Nd to the PLC phenomenon in Mg-Mn alloy identified in previous studies, the PLC characteristics according to alloying elements and deformation conditions were compared and analyzed. To identify the micromechanical mechanisms of the PLC phenomenon, varies in the microstructure and mechanical properties during deformation of Mg-Mn binary and Ca or Nd-containing Mg-Mn-based ternary alloys in various conditions were systemically analyzed. The addition of Ca did not show a marked PLC effect due to the formation of low number density Mn-Ca and Ca-Ca solute clusters and an unbalanced Mn:Ca ratio. In contrast, the addition of Nd leads to the formation of a higher number density of Nd-Nd and Mn-Nd solute clusters than that of Ca-Ca and Mn-Ca solute clusters of the Mg-Mn-Ca alloy, resulting in a stable solute-dislocation interaction atmosphere under specific ranges of deformation temperature and strain rate. The deformation in the regime of PLC phenomenon, results in a decrease in ductility and an increase in strength, despite deformation at elevated temperatures with maintaining the weakened texture.

Effect of CO_(2)exposure on the mechanical strength of geopolymerstabilized sandy soils

In recent years,there has been growing interest in developing methods for mitigating greenhouse effect,as greenhouse gas emissions continue to contribute to global temperature rise.On the other hand,investigating geopolymers as environmentally friendly binders to mitigate the greenhouse effect using soil stabilization has been widely conducted.However,the effect of CO_(2)exposure on the mechanical properties of geopolymer-stabilized soils is rarely reported.In this context,the effect of CO_(2)exposure on the mechanical and microstructural features of sandy soil stabilized with volcanic ash-based geopolymer was investigated.Several factors were concerned,for example the binder content,relative density,CO_(2)pressure,curing condition,curing time,and carbonate content.The results showed that the compressive strength of the stabilized sandy soil specimens with 20%volcanic ash increased from 3 MPa to 11 MPa.It was also observed that 100 kPa CO_(2)pressure was the optimal pressure for strength development among the other pressures.The mechanical strength showed a direct relationship with binder content and carbonate content.Additionally,in the ambient curing(AC)condition,the mechanical strength and carbonate content increased with the curing time.However,the required water for carbonation evaporated after 7 d of oven curing(OC)condition and as a result,the 14-d cured samples showed lower mechanical strength and carbonate content in comparison with 7-d cured samples.Moreover,the rate of strength development was higher in OC cured samples than AC cured samples until 7 d due to higher geopolymerization and carbonation rate.

Giant reversible barocaloric effects with high thermal cycle stability in epoxybonded(MnCoGe)_(0.96)(CuCoSn)_(0.04) composite

Hexagonal MnMX-based(M=Co or Ni,X=Si or Ge)alloys exhibit giant reversible barocaloric effects.However,giant volume expansion would result in the as-cast MnMX ingots fragmenting into powders,and inevitably bring the deterioration of mechanical properties and formability.Grain fragmentation can bring degradation of structural transformation entropy change during cyclic application and removal of pressure.In this paper,giant reversible barocaloric effects with high thermal cycle stability can be achieved in the epoxy bonded(MnCoGe)0.96(CuCoSn)0.04 composite.Giant reversible isothermal entropy change of 43.0 J·kg^(−1)·K^(−1) and adiabatic temperature change from barocaloric effects(ΔT_(BCE))of 15.6 K can be obtained within a wide temperature span of 30 K at 360 MPa,which is mainly attributed to the integration of the change in the transition temperature driven by pressure of−101 K·GPa^(−1) and suitable thermal hysteresis of 11.1 K.Further,the variation of reversibleΔ_(TBCE) against the applied hydrostatic pressure reaches up to 43 K·GPa^(−1),which is at the highest level among the other reported giant barocaloric compounds.More importantly,after 60 thermal cycles,the composite does not break and the calorimetric curves coincide well,demonstrating good thermal cycle stability.

The effect of seismic action on stability of saline soil subgrade in cold region based on isothermal stratification method

With the change of seasons, the shear strength of saline soil subgrade filler will change with the change of external temperature, which will aggravate the adverse effects of seismic on the subgrade. To explore the influence of seismic action on the stability of saline soil subgrade under the influence of temperature on the strength of saline soil subgrade filler, this paper first carried out saline soil shear tests at different temperatures to obtain the influence of temperature on the shear strength of saline soil. Then, the temperature field of the saline soil subgrade was simulated, and then based on the subgrade isothermal stratification model and FLAC3D, the displacement and acceleration amplification effects of seismic action on the shady slope, sunny slope and subgrade of saline soil subgrade in different months were analyzed. The following conclusions were finally drawn: under the action of seismic, In the process of the change of subgrade temperature of Qarhan-Golmud Expressway between 7.7°C and 27°C, the change of saline soil cohesion is the main factor affecting the stability of subgrade slope, and the maximum and minimum values of subgrade surface settlement appear in September and June of each year,respectively. In August, the differences of settlement between the shady slope and the sunny slope shoulder of the subgrade were the largest, and the acceleration of the shady slope and the sunny slope and the inside of the subgrade changed most significantly in the vertical direction. Special attention should be paid to the seismic early warning in the above key months;In the range from both sides of the shoulder to the centerline of the roadbed,the acceleration amplification effect starts to increase significantly from about 3m from the centerline of the roadbed to the centerline, so it is necessary to pay attention to the seismic design of this range.

Effect of spin on the instability of THz plasma waves in field-effect transistors under non-ideal boundary conditions

Terahertz(THz) radiation can be generated due to the instability of THz plasma waves in field-effect transistors(FETs). In this work, we discuss the instability of THz plasma waves in the channel of FETs with spin and quantum effects under non-ideal boundary conditions. We obtain a linear dispersion relation by using the hydrodynamic equation, Maxwell equation and spin equation. The influence of source capacitance, drain capacitance, spin effects, quantum effects and channel width on the instability of THz plasma waves under the non-ideal boundary conditions is investigated in great detail. The results of numerical simulation show that the THz plasma wave is unstable when the drain capacitance is smaller than the source capacitance;the oscillation frequency with asymmetric boundary conditions is smaller than that under non-ideal boundary conditions;the instability gain of THz plasma waves becomes lower under non-ideal boundary conditions. This finding provides a new idea for finding efficient THz radiation sources and opens up a new mechanism for the development of THz technology.

Experimental study on the irreversible displacement evolution and energy dissipation characteristics of disturbance instability of regular joints

To investigate the disturbance-induced shear instability mechanism of structural catastrophe in the deep rock mass,MTS 815 material testing machine was used to carry out quasi-static loading tests and disturbance shear tests on symmetrical regular dentate joints of two materials at three undulation angles under specific initial static stress,disturbance frequency,and peak value.The test results indicate that:(i)the total ultimate instability displacement is only related to the intrinsic properties of the joints but not to the initial static stress and disturbance parameters;(ii)the cumulative irreversible displacement required for the disturbance instability conforms to the logistic inverse function relationship with the number of disturbances,displaying the variation trend of“rapid increase in the front,stable in the middle,and sudden increase in the rear”;(iii)the accumulation of plastic deformation energy is consistent with the evolution law of irreversible displacement of joints and the overall proportion of hysteretic energy is not large;(iv)the dissipated energy required for the instability of each group of joints is basically the same under various disturbance conditions,and this energy is mainly controlled by the initial shear stress and has no connection with the disturbance parameters.The stability of the total disturbance deformation and the disturbance energy law of the joints revealed in the tests provide data support for reasonably determining the disturbance instability criterion of joints.

Stability analysis of magnetization in a perpendicular magnetic layer driven by spin Hall effect

We investigate the stability of magnetization in free layer where the spin torque is induced by the spin Hall effect.In terms of the Landau–Liftshitz–Gilbert equation,we find the low-energy and high-energy equilibrium states,as well as the saddle points.The stability region is defined in the phase diagram spanned by the current density and the spin Hall angle.The spin Hall effect makes the previous saddle point into a stable state above a critical current.However,in the presence of magnetic field,the spin Hall effect leads to the opposite changes in the stable regions of the two low-energy states.

Effect of wall-cooling on Mack-mode instability in high speed flat-plate boundary layers

The instability of the Mack mode is destabilized by wall-cooling in a high speed boundary layer. The aim of this paper is to study the mechanism of the wall cooling effect on the Mack mode instability by numerical methods. It is shown that the wall-cooling can destabilize the Mack mode instability, similar to the previous conclusions with the exception that the Mack mode instability can be stabilized by wall-cooling if the wall temperature is extremely low. The reversed wall temperature is related to a freestream condition. If the Mach number increases to a large enough value, e.g., about 7, the reversed wall temperature will tend to be zero. It seems that the Mack mode instability is determined by the region between the boundary layer edge and the critical layer. When the wall temperature decreases, this region becomes wider, and the boundary layer becomes more unstable. Additionally, a relative supersonic unstable mode can be observed when the velocity of the critical layer is less than 1 - liMa or is cancelled by the wall-cooling effect. These results provide a deeper understanding on the wall-cooling effect in high speed boundary layers.

Insights into ionic association boosting water oxidation activity and dynamic stability

There have been reports about Fe ions boosting oxygen evolution reaction(OER)activity of Ni-based catalysts in alkaline conditions,while the origin and reason for the enhancement remains elusive.Herein,we attempt to identify the activity improvement and discover that Ni sites act as a host to attract Fe(Ⅲ)to form Fe(Ni)(Ⅲ)binary centres,which serve as the dynamic sites to promote OER activity and stability by cyclical formation of intermediates(Fe(Ⅲ)→Fe(Ni)(Ⅲ)→Fe(Ni)-OH→Fe(Ni)-O→Fe(Ni)OOH→Fe(Ⅲ))at the electrode/electrolyte interface to emit O_(2).Additionally,some ions(Co(Ⅱ),Ni(Ⅱ),and Cr(Ⅲ))can also be the active sites to catalyze the OER process on a variety of electrodes.The Fe(Ⅲ)-catalyzed overall water-splitting electrolyzer comprising bare Ni foam as the anode and Pt/Ni-Mo as the cathode demonstrates robust stability for 1600 h at 1000 mA cm^(-2)@~1.75 V.The results provide insights into the ioncatalyzed effects boosting OER performance.

Effects of walk-off on cross-phase modulation induced modulation instability in an optical fibre with high-order dispersion

This paper investigates the effects of walk-off among optical pulses on cross-phase modulation induced modulation instability in the normal dispersion region of an optical fibre with high-order dispersion. The results indicate that, in the case of high-order dispersion, the walk-off effect takes on new characteristics and will influence considerably the shape, position and especially the number of the spectral regions of the gain spectra of modulation instability. Not only the group-velocity mismatch, but also the difference of the third-order dispersion of two optical waves will alter the gain spectra of modulation instability but in different ways. Depending on the values of the walk-off parameters, the number of the spectral regions may increase from two to at most four, and the spectral shape and position may change too.

Stabilizing effect of plasma discharge on bubbling fluidized granular bed

Fluidized beds have been widely used for processing granular materials. In this paper, we study the effect of plasma on the fluidization behavior of a bubbling fluidized bed with an atmospheric pressure plasma discharger. Experiment results show that the bubbling fluidized bed is stabilized with the discharge of plasma. When the discharge current reaches a minimum stabilization current Cms, air bubbles in the bed will disappear and the surface fluctuation is completely suppressed.A simplified model is proposed to consider the effect of electric Coulomb force generated by the plasma. It is found that the Coulomb force will propel the particles to move towards the void area, so that the bubbling fluidized bed is stabilized with a high enough plasma discharge.

The Roles of Barotropic Instability and the Beta Effect in the Eyewall Evolution of Tropical Cyclones

Diabatic heating by convection in the eyewall often produces an annular region of high potential vorticity(PV)around the relatively low PV eye in a strong tropical cyclone(TC).Such a PV ring is barotropically unstable and can encourage the exponential growth of PV waves.In this study,such instability and the subsequent nonlinear evolution of three TC-like vortices having PV rings with different degrees of hollowness on an f-plane are first examined using an unforced,inviscid shallow-water-equation model.Results show that the simulated eyewalls evolve similarly to those in the nondivergent barotropic model.It is also found that the polygonal eyewall structure can be decomposed into vortex Rossby waves(VRWs)of different wavenumbers with different amplitudes,allowing for wave-wave interactions to produce complicated behaviors of mesovortices in the TC eyewall.The same set of PV rings has been examined on a beta-plane.Although the beta effect has been rendered unimportant to the eyewall evolution due to the relatively small scale of the inner-core circulation,this study shows that the beta effect may erode the coherent structure of mesovortices in the eyewall of an initially hollow PV-ring vortex.Mesovortices modeled on the beta-plane with a greater beta parameter tend to experience an earlier breakdown and enhanced radial gradients of the basic-state(azimuthally mean)angular velocity,followed by wave-wave,wave-flow interactions,leading to earlier merger and axisymmetrization processes.This result implies that the beta effect could be one of the forcings that shorten the lifetime of quasi-steady mesovortices in the eyewall of real TCs.

Global stability coefficient of large underground caverns under static loading and earthquake wave condition

Underground energy and resource development,deep underground energy storage and other projects involve the global stability of multiple interconnected cavern groups under internal and external dynamic disturbances.An evaluation method of the global stability coefficient of underground caverns based on static overload and dynamic overload was proposed.Firstly,the global failure criterion for caverns was defined based on its band connection of plastic-strain between multi-caverns.Then,overloading calculation of the boundary geostress and seismic intensity on the caverns model was carried out,and the critical unstable state of multi-caverns can be identified,if the plastic-strain band appeared between caverns during these overloading processes.Thus,the global stability coefficient for the multi-caverns under static loading and earthquake was obtained based on the corresponding overloading coefficient.Practical analysis for the Yingliangbao(YLB)hydraulic caverns indicated that this method can not only effectively obtain the global stability coefficient of caverns under static and dynamic earthquake conditions,but also identify the caverns’high-risk zone of local instability through localized plastic strain of surrounding rock.This study can provide some reference for the layout design and seismic optimization of underground cavern group.

Three-dimensional stability calculation method for high and large composite slopes formed by mining stope and inner dump in adjacent open pits

The 2D limit equilibrium method is widely used for slope stability analysis.However,with the advancement of dump engineering,composite slopes often exhibit significant 3D mechanical effects.Consequently,it is of significant importance to develop an effective 3D stability calculation method for composite slopes to enhance the design and stability control of open-pit slope engineering.Using the composite slope formed by the mining stope and inner dump in Baiyinhua No.1 and No.2 open-pit coal mine as a case study,this research investigates the failure mode of composite slopes and establishes spatial shape equations for the sliding mass.By integrating the shear resistance and sliding force of each row of microstrip columns onto the bottom surface of the strip corresponding to the main sliding surface,a novel 2D equivalent physical and mechanical parameters analysis method for the strips on the main sliding surface of 3D sliding masses is proposed.Subsequently,a comprehensive 3D stability calculation method for composite slopes is developed,and the quantitative relationship between the coordinated development distance and its 3D stability coefficients is examined.The analysis reveals that the failure mode of the composite slope is characterized by cutting-bedding sliding,with the arc serving as the side interface and the weak layer as the bottom interface,while the destabilization mechanism primarily involves shear failure.The spatial form equation of the sliding mass comprises an ellipsoid and weak plane equation.The analysis revealed that when the coordinated development distance is 1500 m,the error rate between the 3D stability calculation result and the 2D stability calculation result of the composite slope is less than 8%,thereby verifying the proposed analytical method of equivalent physical and mechanical parameters and the 3D stability calculation method for composite slopes.Furthermore,the3D stability coefficient of the composite slope exhibits an exponential correlation with the coordinated development distance,with the coefficient gradually decreasing as the coordinated development distance increases.These findings provide a theoretical guideline for designing similar slope shape parameters and conducting stability analysis.

Stability analysis of loose accumulation slopes under rainfall:case study of a high‑speed railway in Southwest China

The high and steep slopes along a high-speed railway in the mountainous area of Southwest China are mostly composed of loose accumulations of debris with large internal pores and poor stability,which can easily induce adverse geological disasters under rainfall conditions.To ensure the smooth construction of the high-speed railway and the subsequent safe operation,it is necessary to master the stability evolution process of the loose accumulation slope under rainfall.This article simulates rainfall using the finite element analysis software’s hydromechanical coupling module.The slope stability under various rainfall situations is calculated and analysed based on the strength reduction method.To validate the simulation results,a field monitoring system is established to study the deformation characteristics of the slope under rainfall.The results show that rainfall duration is the key factor affecting slope stability.Given a constant amount of rainfall,the stability of the slope decreases with increasing duration of rainfall.Moreover,when the amount and duration of rainfall are constant,continuous rainfall has a greater impact on slope stability than intermittent rainfall.The setting of the field retaining structures has a significant role in improving slope stability.The field monitoring data show that the slope is in the initial deformation stage and has good stability,which verifies the rationality of the numerical simulation method.The research results can provide some references for understanding the influence of rainfall on the stability of loose accumulation slopes along high-speed railways and establishing a monitoring system.

Improved combustion stability of biogas at different CO_(2) concentrations using inhomogeneous partially premixed stratified flames

Biogas is a renewable and clean energy source that plays an important role in the current environment of lowcarbon transition.If high-content CO_(2) in biogas can be separated,transformed,and utilized,it not only realizes high-value utilization of biogas but also promotes carbon reduction in the biogas field.To improve the combustion stability of biogas,an inhomogeneous,partially premixed stratified(IPPS)combustion model was adopted in this study.The thermal flame structure and stability were investigated for a wide range of mixture inhomogeneities,turbulence levels,CO_(2) concentrations,air-to-fuel velocity ratios,and combustion energies in a concentric flow slot burner(CFSB).A fine-wire thermocouple is used to resolve the thermal flame structure.The flame size was reduced by increasing the CO_(2) concentration and the flames became lighter blue.The flame temperature also decreased with increase in CO_(2) concentration.Flame stability was reduced by increasing the CO_(2) concentration.However,at a certain level of mixture inhomogeneity,the concentration of CO_(2) in the IPPS mode did not affect the stability.Accordingly,the IPPS mode of combustion should be suitable for the combustion and stabilization of biogas.This should support the design of highly stabilized biogas turbulent flames independent of CO_(2) concentration.The data show that the lower stability conditions are partially due to the change in fuel combustion energy,which is characterized by the Wobbe index(WI).In addition,at a certain level of mixture inhomogeneity,the effect of the WI on flame stability becomes dominant.

Cylindrical effects in weakly nonlinear Rayleigh Taylor instability

The classical Rayleigh–Taylor instability（RTI） at the interface between two variable density fluids in the cylindrical geometry is explicitly investigated by the formal perturbation method up to the second order. Two styles of RTI, convergent（i.e., gravity pointing inward） and divergent（i.e., gravity pointing outwards） configurations, compared with RTI in Cartesian geometry, are taken into account. Our explicit results show that the interface function in the cylindrical geometry consists of two parts： oscillatory part similar to the result of the Cartesian geometry, and non-oscillatory one contributing nothing to the result of the Cartesian geometry. The velocity resulting only from the non-oscillatory term is followed with interest in this paper. It is found that both the convergent and the divergent configurations have the same zeroth-order velocity, whose magnitude increases with the Atwood number, while decreases with the initial radius of the interface or mode number. The occurrence of non-oscillation terms is an essential character of the RTI in the cylindrical geometry different from Cartesian one.

Phase Effect on Mode Coupling in Kelvin—Helmholtz Instability for Two-Dimensional Incompressible Fluid

This paper studies the phase effect in mode coupling of Kelvin-Helmholtz instability in two-dimensionalincompressible fluid.It is found that there is an important growth phenomenon of every mode in the mode couplingprocess.The growth changes periodically with phase difference and in the condition of our simulation the period is about0.7π.The period characteristic is apparent in all stage of the mode coupling process,especially in the relatively laterstage.