Unraveling the efficiency losses and improving methods in quantum dot-based infrared up-conversion photodetectors

Quantum dot-based up-conversion photodetector,in which an infrared photodiode(PD)and a quantum dot light-emitting diode(QLED)are back-to-back connected,is a promising candidate for low-cost infrared imaging.However,the huge efficiency losses caused by integrating the PD and QLED together hasn’t been studied sufficiently.This work revealed at least three origins for the efficiency losses.First,the PD unit and QLED unit usually didn’t work under optimal conditions at the same time.Second,the potential barriers and traps at the interconnection between PD and QLED units induced unfavorable carrier recombination.Third,much emitted visible light was lost due to the strong visible absorption in the PD unit.Based on the understandings on the loss mechanisms,the infrared up-conversion photodetectors were optimized and achieved a breakthrough photon-to-photon conversion efficiency of 6.9%.This study provided valuable guidance on how to optimize the way of integration for up-conversion photodetectors.

Evaluation of corrosion resistance, mechanical integrity loss and biocompatibility of PCL/HA/TiO_(2) hybrid coated biodegradable ZM21 Mg alloy

A novel PCL/HA/TiO_(2)hybrid coating on ZM21 Mg alloy substrate has been investigated for corrosion resistance, biocompatibility and mechanical integrity loss in terms of bending, compressive and tensile strength in physiological media. The prepared hybrid coating was dip coated over ZM21 from HA/TiO_(2)and PCL solutions followed by creating a microporous PCL layer by utilizing Non-solvent Induced Phase Separation(NIPS) technique. The electrochemical measurement and in-vitro degradation study in SBF after 28 days showed that the PCL/HA/TiO_(2) hybrid coating reduced H2 evolution rate, weight loss, and corrosion rate by 64, 116 and 118 times respectively, as compared to uncoated ZM21 samples. The surface studies carried out using SEM-EDX, FTIR and XRD revealed formation of highly stable 3d flower-like HA crystals with Ca/P ratio of 1.60 in the PCL micropores. This dense apatite growth effectively protected the PCL/HA/TiO_(2)hybrid coated samples to maintain the good mechanical integrity even after 28 days of immersion as compared to HA/TiO_(2)composite coated, As-polished(A/P) and As-machined(A/M) samples. The failure analysis of samples under mechanical loading were performed using SEM-BSE-EBSD.The in-vitro cellular viability of L929 fibroblast cells on PCL/HA/TiO_(2)hybrid coating was found 50.47% higher with respect to control group,whereas bacterial viability was supressed by 57.15 and 62.35% against gram-positive Staphylococcus aureus and gram-negative Escherichia coli bacterial models. The comprehensive assessment indicates PCL/HA/TiO_(2)hybrid coating as a suitable candidate to delay early degradation and mechanical integrity loss of Mg-based alloys for devising biodegradable orthopaedic implant.

Effect of unbalanced and common losses in quantum photonic integrated circuits

Loss is inevitable for the optical system due to the absorption of materials, scattering caused by the defects, and surface roughness. In quantum optical circuits, the loss can not only reduce the intensity of the signal, but also affect the performance of quantum operations. In this work, we divide losses into unbalanced linear losses and shared common losses, and provide a detailed analysis on how loss affects the integrated linear optical quantum gates. It is found that the orthogonality of eigenmodes and the unitary phase relation of the coupled waveguide modes are destroyed by the loss. As a result, the fidelity of single-and two-qubit operations decreases significantly as the shared loss becomes comparable to the coupling strength. Our results are important for the investigation of large-scale photonic integrated quantum information processes.

Behavioral Portfolio Selection with Loss Control

In this paper we formulate a continuous-time behavioral （4 la cumulative prospect theory） portfolio selection model where the losses are constrained by a pre-specified upper bound. Economically the model is motivated by the previously proved fact that the losses Occurring in a bad state of the world can be catastrophic for an unconstrained model. Mathematically solving the model boils down to solving a concave Choquet minimization problem with an additional upper bound. We derive the optimal solution explicitly for such a loss control model. The optimal terminal wealth profile is in general characterized by three pieces： the agent has gains in the good states of the world, gets a moderate, endogenously constant loss in the intermediate states, and suffers the maximal loss （which is the given bound for losses） in the bad states. Examples are given to illustrate the general results.

Application of resist-profile-aware source optimization in 28 nm full chip optical proximity correction

As technology node shrinks, aggressive design rules for contact and other back end of line（BEOL）layers continue to drive the need for more effective full chip patterning optimization. Resist top loss is one of the major challenges for 28 nm and below technology nodes, which can lead to post-etch hotspots that are difficult to predict and eventually degrade the process window significantly. To tackle this problem, we used an advanced programmable illuminator（FlexRay） and Tachyon SMO（Source Mask Optimization） platform to make resistaware source optimization possible, and it is proved to greatly improve the imaging contrast, enhance focus and exposure latitude, and minimize resist top loss thus improving the yield.