In this work, a novel airframe/propulsion integration design method of the wing-body configuration for hypersonic cruise aircraft is proposed, where the configuration is integrated with inward-turning inlets. With the...In this work, a novel airframe/propulsion integration design method of the wing-body configuration for hypersonic cruise aircraft is proposed, where the configuration is integrated with inward-turning inlets. With the help of this method, the major design concern of balancing the aerodynamic performance against the requirements for efficient propulsion can be well addressed. A novel geometric parametrically modelling method based on a combination of patched class and shape transition(CST) and COONs surface is proposed to represent the configuration, especially a complex configuration with an irregular inlet lip shape. The modelling method enlarges the design space of components on the premise of guaranteeing the configuration integrity via special constraints imposed on the interface across adjacent surfaces. A basic flow inside a cone shaped by a dual-inflection-point generatrix is optimized to generate the inward-turning inlet with improvements of both compression efficiency and flow uniformity. The performance improvement mechanism of this basic flow is the compression velocity variation induced by the variation of the generatrix slope along the flow path. At the design point, numerical simulation results show that the lift-to-drag ratio of the configuration is as high as 5.2 and the inlet works well with a high level of compression efficiency and flow uniformity. The design result also has a good performance on off-design conditions. The achievement of all the design targets turns out that the integration design method proposed in this paper is efficient and practical.展开更多
A smart city provides a new idea and model for urban construction, management, and development. This article proposes the concepts and methodology for top-level design of smart cities based on the " Integration of Fo...A smart city provides a new idea and model for urban construction, management, and development. This article proposes the concepts and methodology for top-level design of smart cities based on the " Integration of Four Plans ", and the planning process and systems for implementing the top-level design of smart cities. This article discusses, from the perspective of a city, how to optimize resource allocation, coordinate the development of urban economy, society, resources, environment, and people's livelihood, and map out the blueprints for healthy and sustainable development of a smart city.展开更多
According to the variable toe-to-heel well spacing, combined with the dislocation theory, discrete lattice method, and finite-element-method(FEM) based fluid-solid coupling, an integrated geological-engineering method...According to the variable toe-to-heel well spacing, combined with the dislocation theory, discrete lattice method, and finite-element-method(FEM) based fluid-solid coupling, an integrated geological-engineering method of volume fracturing for fan-shaped well pattern is proposed considering the geomechanical modeling, induced stress calculation, hydraulic fracturing simulation, and post-frac productivity evaluation. Besides, we propose the differential fracturing design for the conventional productivity-area and the potential production area for fan-shaped horizontal wells. After the fracturing of the conventional production area for H1 fan-shaped well platform, the research shows that the maximum reduction of the horizontal principal stress difference in the potential productivity-area is 0.2 MPa, which cannot cause the stress reversal, but this reduction is still conducive to the lateral propagation of hydraulic fractures. According to the optimized fracturing design, in zone-Ⅰ of the potential production area, only Well 2 is fractured, with a cluster spacing of 30 m and an injection rate of 12 m^(3)/min per stage;in zone-Ⅱ, Well 2 is fractured before Well 3, with a cluster spacing of 30 m and an injection rate of 12 m^(3)/min per stage. The swept area of the pore pressure drop in the potential production area is small, showing that the reservoir is not well developed. The hydraulic fracturing in the toe area can be improved by, for example, properly densifying the fractures and adjusting the fracture distribution, in order to enhance the swept volume and increase the reservoir utilization.展开更多
Electric vehicles(EVs)have garnered significant attention as a vital driver of economic growth and environmental sustainability.Nevertheless,ensuring the safety of high-energy batteries is now a top priority that cann...Electric vehicles(EVs)have garnered significant attention as a vital driver of economic growth and environmental sustainability.Nevertheless,ensuring the safety of high-energy batteries is now a top priority that cannot be overlooked during large-scale applications.This paper proposes an innovative active protection and cooling integrated battery module using smart materials,magneto-sensitive shear thickening fluid(MSTF),which is specifically designed to address safety threats posed by lithium-ion batteries(LIBs)exposed to harsh mechanical and environmental conditions.The theoretical framework introduces a novel approach for harnessing the smoothed-particle hydrodynamics(SPH)methodology that incorporates the intricate interplay of non-Newtonian fluid behavior,capturing the fluid-structure coupling inherent to the MSTF.This approach is further advanced by adopting an enhanced Herschel-Bulkley(H-B)model to encapsulate the intricate rheology of the MSTF under the influence of the magnetorheological effect(MRE)and shear thickening(ST)behavior.Numerical simulation results show that in the case of cooling,the MSTF is an effective cooling medium for rapidly reducing the temperature.In terms of mechanical abuse,the MSTF solidifies through actively applying the magnetic field during mechanical compression and impact within the battery module,resulting in 66%and 61.7%reductions in the maximum stress within the battery jellyroll,and 31.1%and 23%reductions in the reaction force,respectively.This mechanism effectively lowers the risk of short-circuit failure.The groundbreaking concepts unveiled in this paper for active protection battery modules are anticipated to be a valuable technological breakthrough in the areas of EV safety and lightweight/integrated design.展开更多
For the non-stop demands for a better and smarter society, the number of electronic devices keeps increasing exponentially;and the computation power, communication data rate, smart sensing capability and intelligence ...For the non-stop demands for a better and smarter society, the number of electronic devices keeps increasing exponentially;and the computation power, communication data rate, smart sensing capability and intelligence are always not enough. Hardware supports software, while the integrated circuit(IC) is the core of hardware. In this long review paper, we summarize and discuss recent trending IC design directions and challenges, and try to give the readers big/cool pictures on each selected small/hot topics. We divide the trends into the following six categories, namely, 1) machine learning and artificial intelligence(AI) chips, 2) communication ICs, 3) data converters, 4) power converters, 5) imagers and range sensors, 6) emerging directions. Hope you find this paper useful for your future research and works.展开更多
Based on fundamental principles of ecology ,the ecological philosophy connotation of Feng-Shui(Wind and Water) concept from experiences of Chinese agricultural culture was first discussed , and then hu-man-ecological ...Based on fundamental principles of ecology ,the ecological philosophy connotation of Feng-Shui(Wind and Water) concept from experiences of Chinese agricultural culture was first discussed , and then hu-man-ecological implications of Feng-Shui environment architecture is analyzed. As a theoretical integrationbetween human ecology and Feng-Shui theory ,“environment” and “environmental design” concepts were re-examined and given new definitions. With holistic principles of human ecological design in the context ofFeng-Shui , essential technical ways of integrative human ecological design were explored in the presentationof a case study of an urban environmental design in east China.展开更多
This paper creates 3D solid model and assembly of U RJ 92-6 oil tank and analyses its strength by integrated CAD/CAE/CAM software I-D EAS. Through integrated simulation in computer, design efficiency and quality of oi...This paper creates 3D solid model and assembly of U RJ 92-6 oil tank and analyses its strength by integrated CAD/CAE/CAM software I-D EAS. Through integrated simulation in computer, design efficiency and quality of oil tank is greatly improved. Adopting integrated CAD/CAE/CAM software to carry out integrated research to equ ipment and products, we will be able to take overall analysis in aspects of 3-D solid modeling, pre-assembly and strength, etc., to realize non-paper designi ng and parallel designing. Problems can be found and settled during designing, w hich will increase designing efficiency and one-time success rate and realize o ptimum designing for products.展开更多
The integrated layout problem in manufacturing Systems is investigated. Anintegrated model for Concurrent layout design of cells and flow paths is formulated. A hybridapproach combined an enhanced branch-and-bound alg...The integrated layout problem in manufacturing Systems is investigated. Anintegrated model for Concurrent layout design of cells and flow paths is formulated. A hybridapproach combined an enhanced branch-and-bound algorithm with a simulated annealing scheme isproposed to solve this problem. The integrated layout method is applied to re-layout the gear pumpshop of a medium-size manufacturer of hydraulic pieces. Results show that the proposed layout methodcan concurrently provide good solutions of the cell layouts and the flow path layouts.展开更多
An analytical model for current-voltage behavior of amorphous In-Ga-Zn-O thin-film transistors(a-IGZO TFTs)with dual-gate structures is developed.The unified expressions for synchronous and asynchronous operating mo...An analytical model for current-voltage behavior of amorphous In-Ga-Zn-O thin-film transistors(a-IGZO TFTs)with dual-gate structures is developed.The unified expressions for synchronous and asynchronous operating modes are derived on the basis of channel charges,which are controlled by gate voltage.It is proven that the threshold voltage of asynchronous dual-gate IGZO TFTs is adjusted in proportion to the ratio of top insulating capacitance to the bottom insulating capacitance(C_(TI)/C_(BI)).Incorporating the proposed model with Verilog-A,a touch-sensing circuit using dual-gate structure is investigated by SPICE simulations.Comparison shows that the touch sensitivity is increased by the dual-gate IGZO TFT structure.展开更多
Die casting process is one of the prime options for m anufacturing precisely dimensioned, sharply defined metal parts. The design of d ie casting dies comprises several stages and entails a large amount of time. Tra d...Die casting process is one of the prime options for m anufacturing precisely dimensioned, sharply defined metal parts. The design of d ie casting dies comprises several stages and entails a large amount of time. Tra ditionally, the different stages of the die design were not integrated but exist as separate entities. Moreover, recurring modifications or even redesigns are r equired due to the complexity in achieving an accurate initial die design. As a result, die design is usually time-consuming and costly with respect to resourc es. The die casting industry will greatly benefit if proper application software are developed that integrates the different die design stages and allows editin g of die design as and when needed. Hence it is imperative to create an integrat ed die design system that shortens the die design time. This paper presents a research that establishes a prototype of an integrated die design system. It is developed using the commercial SolidWorks CAD system and n amed DiWorks. The aim of building the system on a commercial CAD system is to ut ilise the resources and features of the CAD system to speed up the die design pr ocess. DiWorks consists of six distinct modules: Project Manager, Cavity Insert Builder, Gating System Constructor, Die Base Designer, Ejector System Constructo r and Standard Components Library. Through these six modules, the die designer c an create a complete die casting die beginning from a product part model. It is a user-friendly system that allows both experienced and novice die designers to easily accomplish the task of die design. The practical goal of this research is twofold: to develop a system that integra tes the die design process and at the same time facilitates the editing of d ie design during or after the course of the design process. The research approac h includes (i) parametric design, (ii) feature-based design (iii) system modeli ng and implementation. Parametric design deals with variable dimensions as contr ol parameters, and it is an efficient tool for creating models based on paramete rs. Parametric design not only increases the design efficiency, but also makes t he updates and modifications of existing designs easier and faster, since these can be achieved by changing the parameters of the parametric model. Feature-bas ed design is used to design a product with features that are functionally define d by attributes and are geometrically represented by a set of parameters. The re sults of this research will aid the automation of the die design process, thus i mproving the efficiency and quality of, and reducing the cost of die design.展开更多
This paper describes how database information and electronic 3D models are integrated to produce power plant designs more efficiently and accurately. Engineering CAD/CAE systems have evolved from strictly 3D modeling ...This paper describes how database information and electronic 3D models are integrated to produce power plant designs more efficiently and accurately. Engineering CAD/CAE systems have evolved from strictly 3D modeling to spatial data management tools. This paper describes how process data, commodities, and location data are disseminated to the various project team members through a central integrated database. The database and 3D model also provide a cache of information that is valuable to the constructor, and operations and maintenance Personnel.展开更多
Reversible logic is a new emerging technology with many promising applications in optical information processing, low power (Complementary Metal Oxide Semiconductor) CMOS design, (De Oxy RiboNucleic Acid) DNA computin...Reversible logic is a new emerging technology with many promising applications in optical information processing, low power (Complementary Metal Oxide Semiconductor) CMOS design, (De Oxy RiboNucleic Acid) DNA computing, etc. In industrial automation, comparators play an important role in segregating faulty patterns from good ones. In previous works, these comparators have been implemented with more number of reversible gates and computational complexity. All these comparators use propagation technique to compare the data. This will reduce the efficiency of the comparators. To overcome the problem, this paper proposes an efficient comparator using (Thapliyal Ranganathan) TR gate utilizing full subtraction and half subtraction algorithm which will improve the computation efficiency. The comparator design using half subtraction algorithm shows an improvement in terms of quantum cost. The comparator design using full subtraction algorithm shows effectiveness in reducing number of reversible gates required and garbage output.展开更多
A CAD tools environment is described to support concurrent collaborative design. The environment has four components: shared design representation, design process control, CAD tools, designer interface. So...A CAD tools environment is described to support concurrent collaborative design. The environment has four components: shared design representation, design process control, CAD tools, designer interface. Some related issues for the construction, such as form feature handling, constraint satisfaction, design process control, STEP based information integration, are discussed in more detail.展开更多
A kind of networked control system with network-induced delay and packet dropout, modeled on asynchronous dynamical systems was tested, and the integrity design of the networked control system with sensors failures an...A kind of networked control system with network-induced delay and packet dropout, modeled on asynchronous dynamical systems was tested, and the integrity design of the networked control system with sensors failures and actuators failures was analyzed using hybrid systems technique based on the robust fault-tolerant control theory. The parametric expression of controller is given based on the feasible solution of linear matrix inequality. The simulation results are provided on the basis of detailed theoretical analysis, which further demonstrate the validity of the proposed schema.展开更多
In this paper, the operating conditions, technical requirements, performance characteristics, design ideas, application experiences and development trends of aerospace engine bearings, including material technology, i...In this paper, the operating conditions, technical requirements, performance characteristics, design ideas, application experiences and development trends of aerospace engine bearings, including material technology, integration design and reliability, are reviewed. The development history of aerospace engine bearing is recalled briefly at first. Then today's material technologies and the high bearing performances of the bearings obtained through the new materials are introduced, which play important roils in the aeroengine bearing developments. The integration design ideas and practices are explained to indicate its significant advantages and importance to the aerospace engine bearings. And the reliability of the shaft-bearing system is pointed out and treated as the key requirement with goals for both engine and bearing. Finally, as it is believed that the correct design comes from practice, the pre-qualification rig testing conducted by FAG Aerospace GmbH & Co. KG is briefly illustrated as an example. All these lead to the development trends of aerospace engine bearings from different aspects.展开更多
Implementing a control system over a communication network induces inevitable time delays that may degrade performance and even cause instability. One of the most effective ways to reduce the negative effect of delays...Implementing a control system over a communication network induces inevitable time delays that may degrade performance and even cause instability. One of the most effective ways to reduce the negative effect of delays on the performance of networked control system (NCS) is to reduce network traffic. In this paper, adjustable deadbands are explored as a solution to reduce network traffic in NCS. A method of fault-tolerant control of networked control system is presented, which takes into account system response as well as network traffic. The integrity design for a kind of NCS with sensor failures and actuator failures is analyzed based on robust fault-tolerant control theory and information scheduling. After detailed theoretical analysis, the paper also provides the simulation results, which further validate the proposed scheme.展开更多
Assuming the material properties varying with an exponential law both in the thick- ness and radial directions, axisymmetric bending of two-directional functionally graded circular and annular plates is studied using ...Assuming the material properties varying with an exponential law both in the thick- ness and radial directions, axisymmetric bending of two-directional functionally graded circular and annular plates is studied using the semi-analytical numerical method in this paper. The deflections and stresses of the plates are presented. Numerical results show the well accuracy and convergence of the method. Compared with the finite element method, the semi-analytical nu- merical method is with great advantage in the computational efficiency. Moreover, study on ax- isymmetric bending of two-directional functionally graded annular plate shows that such plates have better performance than those made of isotropic homogeneous materials or one-directional functionally graded materials. Two-directional functionally graded material is a potential alternative to the one-directional functionally graded material. And the integrated design of materials and structures can really be achieved in two-directional functionally graded materials.展开更多
The mooring and riser system is the most critical part of an ofshore oil terminal.Traditionally,these two parts are designed separately without considering the nonlinear interaction between them.Thus,the present paper...The mooring and riser system is the most critical part of an ofshore oil terminal.Traditionally,these two parts are designed separately without considering the nonlinear interaction between them.Thus,the present paper aims to develop an inte-grated design process for riser systems with a lazy-S confguration and mooring systems in the ofshore catenary anchor leg mooring(CALM)oil terminal.One of the important criteria considered in this integrated design is the ofset diagram and safe operation zone(SAFOP)related to the mooring system and the riser,respectively.These two diagrams are obtained separately by diferent analyses;therefore,codes or standards are available separately for two components.In this methodol-ogy,the diagrams of both risers and mooring lines are incorporated into a single spiral,thus identifying the safe and failure zones of risers and the mooring lines of the oil terminal.This,in turn,leads to substantial benefts in terms of overall system response,cost reduction,and safety to the ofshore oil terminal.To implement this process,three diferent riser lengths with the lazy-S confguration are considered at three diferent sea depths at the terminal installation site.For each condition,the integrated design of the mooring system and riser is executed according to the derived procedure.Then,coupled dynamic models,wherein both buoys and hoses are included,are developed using OrcaFlex.Results show that the criteria of the relevant regulations are not satisfed by reducing the length of the riser relative to the designed size.Further,as water depth increases,this type of riser confguration shows good coupled performance while interacting with the mooring system.In the cross ofset mode,the maximum margin is created between the ofset diagram and the SAFOP diagram,while the most critical dynamic response of the tanker and terminal system occurs in the near and far modes.Therefore,with this method,the best position for the riser direction with the tanker direction is 90°in the best case.展开更多
基金supported by the ‘‘111" Project of China (No. B17037)
文摘In this work, a novel airframe/propulsion integration design method of the wing-body configuration for hypersonic cruise aircraft is proposed, where the configuration is integrated with inward-turning inlets. With the help of this method, the major design concern of balancing the aerodynamic performance against the requirements for efficient propulsion can be well addressed. A novel geometric parametrically modelling method based on a combination of patched class and shape transition(CST) and COONs surface is proposed to represent the configuration, especially a complex configuration with an irregular inlet lip shape. The modelling method enlarges the design space of components on the premise of guaranteeing the configuration integrity via special constraints imposed on the interface across adjacent surfaces. A basic flow inside a cone shaped by a dual-inflection-point generatrix is optimized to generate the inward-turning inlet with improvements of both compression efficiency and flow uniformity. The performance improvement mechanism of this basic flow is the compression velocity variation induced by the variation of the generatrix slope along the flow path. At the design point, numerical simulation results show that the lift-to-drag ratio of the configuration is as high as 5.2 and the inlet works well with a high level of compression efficiency and flow uniformity. The design result also has a good performance on off-design conditions. The achievement of all the design targets turns out that the integration design method proposed in this paper is efficient and practical.
文摘A smart city provides a new idea and model for urban construction, management, and development. This article proposes the concepts and methodology for top-level design of smart cities based on the " Integration of Four Plans ", and the planning process and systems for implementing the top-level design of smart cities. This article discusses, from the perspective of a city, how to optimize resource allocation, coordinate the development of urban economy, society, resources, environment, and people's livelihood, and map out the blueprints for healthy and sustainable development of a smart city.
基金Supported by National Natural Science Foundation of China (52104029,U2139204)PetroChina Science and Technology Innovation Foundation (2021 DQ02-0501)。
文摘According to the variable toe-to-heel well spacing, combined with the dislocation theory, discrete lattice method, and finite-element-method(FEM) based fluid-solid coupling, an integrated geological-engineering method of volume fracturing for fan-shaped well pattern is proposed considering the geomechanical modeling, induced stress calculation, hydraulic fracturing simulation, and post-frac productivity evaluation. Besides, we propose the differential fracturing design for the conventional productivity-area and the potential production area for fan-shaped horizontal wells. After the fracturing of the conventional production area for H1 fan-shaped well platform, the research shows that the maximum reduction of the horizontal principal stress difference in the potential productivity-area is 0.2 MPa, which cannot cause the stress reversal, but this reduction is still conducive to the lateral propagation of hydraulic fractures. According to the optimized fracturing design, in zone-Ⅰ of the potential production area, only Well 2 is fractured, with a cluster spacing of 30 m and an injection rate of 12 m^(3)/min per stage;in zone-Ⅱ, Well 2 is fractured before Well 3, with a cluster spacing of 30 m and an injection rate of 12 m^(3)/min per stage. The swept area of the pore pressure drop in the potential production area is small, showing that the reservoir is not well developed. The hydraulic fracturing in the toe area can be improved by, for example, properly densifying the fractures and adjusting the fracture distribution, in order to enhance the swept volume and increase the reservoir utilization.
基金Project supported by the National Natural Science Foundation of China(Nos.12072183 and11872236)the Key Research Project of Zhejiang Laboratory(No.2021PE0AC02)。
文摘Electric vehicles(EVs)have garnered significant attention as a vital driver of economic growth and environmental sustainability.Nevertheless,ensuring the safety of high-energy batteries is now a top priority that cannot be overlooked during large-scale applications.This paper proposes an innovative active protection and cooling integrated battery module using smart materials,magneto-sensitive shear thickening fluid(MSTF),which is specifically designed to address safety threats posed by lithium-ion batteries(LIBs)exposed to harsh mechanical and environmental conditions.The theoretical framework introduces a novel approach for harnessing the smoothed-particle hydrodynamics(SPH)methodology that incorporates the intricate interplay of non-Newtonian fluid behavior,capturing the fluid-structure coupling inherent to the MSTF.This approach is further advanced by adopting an enhanced Herschel-Bulkley(H-B)model to encapsulate the intricate rheology of the MSTF under the influence of the magnetorheological effect(MRE)and shear thickening(ST)behavior.Numerical simulation results show that in the case of cooling,the MSTF is an effective cooling medium for rapidly reducing the temperature.In terms of mechanical abuse,the MSTF solidifies through actively applying the magnetic field during mechanical compression and impact within the battery module,resulting in 66%and 61.7%reductions in the maximum stress within the battery jellyroll,and 31.1%and 23%reductions in the reaction force,respectively.This mechanism effectively lowers the risk of short-circuit failure.The groundbreaking concepts unveiled in this paper for active protection battery modules are anticipated to be a valuable technological breakthrough in the areas of EV safety and lightweight/integrated design.
文摘For the non-stop demands for a better and smarter society, the number of electronic devices keeps increasing exponentially;and the computation power, communication data rate, smart sensing capability and intelligence are always not enough. Hardware supports software, while the integrated circuit(IC) is the core of hardware. In this long review paper, we summarize and discuss recent trending IC design directions and challenges, and try to give the readers big/cool pictures on each selected small/hot topics. We divide the trends into the following six categories, namely, 1) machine learning and artificial intelligence(AI) chips, 2) communication ICs, 3) data converters, 4) power converters, 5) imagers and range sensors, 6) emerging directions. Hope you find this paper useful for your future research and works.
文摘Based on fundamental principles of ecology ,the ecological philosophy connotation of Feng-Shui(Wind and Water) concept from experiences of Chinese agricultural culture was first discussed , and then hu-man-ecological implications of Feng-Shui environment architecture is analyzed. As a theoretical integrationbetween human ecology and Feng-Shui theory ,“environment” and “environmental design” concepts were re-examined and given new definitions. With holistic principles of human ecological design in the context ofFeng-Shui , essential technical ways of integrative human ecological design were explored in the presentationof a case study of an urban environmental design in east China.
文摘This paper creates 3D solid model and assembly of U RJ 92-6 oil tank and analyses its strength by integrated CAD/CAE/CAM software I-D EAS. Through integrated simulation in computer, design efficiency and quality of oil tank is greatly improved. Adopting integrated CAD/CAE/CAM software to carry out integrated research to equ ipment and products, we will be able to take overall analysis in aspects of 3-D solid modeling, pre-assembly and strength, etc., to realize non-paper designi ng and parallel designing. Problems can be found and settled during designing, w hich will increase designing efficiency and one-time success rate and realize o ptimum designing for products.
基金This project is supported by National Natural Science Foundation of China (No.59990470)Doctoral Foundation of Ministry of Education, China(No.20010487024).
文摘The integrated layout problem in manufacturing Systems is investigated. Anintegrated model for Concurrent layout design of cells and flow paths is formulated. A hybridapproach combined an enhanced branch-and-bound algorithm with a simulated annealing scheme isproposed to solve this problem. The integrated layout method is applied to re-layout the gear pumpshop of a medium-size manufacturer of hydraulic pieces. Results show that the proposed layout methodcan concurrently provide good solutions of the cell layouts and the flow path layouts.
基金Supported by the National Key Research and Development Program of China under Grant No 2017YFA0204600the National Natural Science Foundation of China under Grant No 61404002the Science and Technology Project of Hunan Province under Grant No 2015JC3041
文摘An analytical model for current-voltage behavior of amorphous In-Ga-Zn-O thin-film transistors(a-IGZO TFTs)with dual-gate structures is developed.The unified expressions for synchronous and asynchronous operating modes are derived on the basis of channel charges,which are controlled by gate voltage.It is proven that the threshold voltage of asynchronous dual-gate IGZO TFTs is adjusted in proportion to the ratio of top insulating capacitance to the bottom insulating capacitance(C_(TI)/C_(BI)).Incorporating the proposed model with Verilog-A,a touch-sensing circuit using dual-gate structure is investigated by SPICE simulations.Comparison shows that the touch sensitivity is increased by the dual-gate IGZO TFT structure.
文摘Die casting process is one of the prime options for m anufacturing precisely dimensioned, sharply defined metal parts. The design of d ie casting dies comprises several stages and entails a large amount of time. Tra ditionally, the different stages of the die design were not integrated but exist as separate entities. Moreover, recurring modifications or even redesigns are r equired due to the complexity in achieving an accurate initial die design. As a result, die design is usually time-consuming and costly with respect to resourc es. The die casting industry will greatly benefit if proper application software are developed that integrates the different die design stages and allows editin g of die design as and when needed. Hence it is imperative to create an integrat ed die design system that shortens the die design time. This paper presents a research that establishes a prototype of an integrated die design system. It is developed using the commercial SolidWorks CAD system and n amed DiWorks. The aim of building the system on a commercial CAD system is to ut ilise the resources and features of the CAD system to speed up the die design pr ocess. DiWorks consists of six distinct modules: Project Manager, Cavity Insert Builder, Gating System Constructor, Die Base Designer, Ejector System Constructo r and Standard Components Library. Through these six modules, the die designer c an create a complete die casting die beginning from a product part model. It is a user-friendly system that allows both experienced and novice die designers to easily accomplish the task of die design. The practical goal of this research is twofold: to develop a system that integra tes the die design process and at the same time facilitates the editing of d ie design during or after the course of the design process. The research approac h includes (i) parametric design, (ii) feature-based design (iii) system modeli ng and implementation. Parametric design deals with variable dimensions as contr ol parameters, and it is an efficient tool for creating models based on paramete rs. Parametric design not only increases the design efficiency, but also makes t he updates and modifications of existing designs easier and faster, since these can be achieved by changing the parameters of the parametric model. Feature-bas ed design is used to design a product with features that are functionally define d by attributes and are geometrically represented by a set of parameters. The re sults of this research will aid the automation of the die design process, thus i mproving the efficiency and quality of, and reducing the cost of die design.
文摘This paper describes how database information and electronic 3D models are integrated to produce power plant designs more efficiently and accurately. Engineering CAD/CAE systems have evolved from strictly 3D modeling to spatial data management tools. This paper describes how process data, commodities, and location data are disseminated to the various project team members through a central integrated database. The database and 3D model also provide a cache of information that is valuable to the constructor, and operations and maintenance Personnel.
文摘Reversible logic is a new emerging technology with many promising applications in optical information processing, low power (Complementary Metal Oxide Semiconductor) CMOS design, (De Oxy RiboNucleic Acid) DNA computing, etc. In industrial automation, comparators play an important role in segregating faulty patterns from good ones. In previous works, these comparators have been implemented with more number of reversible gates and computational complexity. All these comparators use propagation technique to compare the data. This will reduce the efficiency of the comparators. To overcome the problem, this paper proposes an efficient comparator using (Thapliyal Ranganathan) TR gate utilizing full subtraction and half subtraction algorithm which will improve the computation efficiency. The comparator design using half subtraction algorithm shows an improvement in terms of quantum cost. The comparator design using full subtraction algorithm shows effectiveness in reducing number of reversible gates required and garbage output.
文摘A CAD tools environment is described to support concurrent collaborative design. The environment has four components: shared design representation, design process control, CAD tools, designer interface. Some related issues for the construction, such as form feature handling, constraint satisfaction, design process control, STEP based information integration, are discussed in more detail.
基金This project was supported by the National Natural Science Foundation of China (60274014)Doctor Foundation of China Education Ministry (20020487006).
文摘A kind of networked control system with network-induced delay and packet dropout, modeled on asynchronous dynamical systems was tested, and the integrity design of the networked control system with sensors failures and actuators failures was analyzed using hybrid systems technique based on the robust fault-tolerant control theory. The parametric expression of controller is given based on the feasible solution of linear matrix inequality. The simulation results are provided on the basis of detailed theoretical analysis, which further demonstrate the validity of the proposed schema.
文摘In this paper, the operating conditions, technical requirements, performance characteristics, design ideas, application experiences and development trends of aerospace engine bearings, including material technology, integration design and reliability, are reviewed. The development history of aerospace engine bearing is recalled briefly at first. Then today's material technologies and the high bearing performances of the bearings obtained through the new materials are introduced, which play important roils in the aeroengine bearing developments. The integration design ideas and practices are explained to indicate its significant advantages and importance to the aerospace engine bearings. And the reliability of the shaft-bearing system is pointed out and treated as the key requirement with goals for both engine and bearing. Finally, as it is believed that the correct design comes from practice, the pre-qualification rig testing conducted by FAG Aerospace GmbH & Co. KG is briefly illustrated as an example. All these lead to the development trends of aerospace engine bearings from different aspects.
基金Supported by National Natural Science Foundation of P. R. China (60274014)the Specialized Research Fund for Doctoral Program of Higher Education of P. R. China (20020487006)
文摘Implementing a control system over a communication network induces inevitable time delays that may degrade performance and even cause instability. One of the most effective ways to reduce the negative effect of delays on the performance of networked control system (NCS) is to reduce network traffic. In this paper, adjustable deadbands are explored as a solution to reduce network traffic in NCS. A method of fault-tolerant control of networked control system is presented, which takes into account system response as well as network traffic. The integrity design for a kind of NCS with sensor failures and actuator failures is analyzed based on robust fault-tolerant control theory and information scheduling. After detailed theoretical analysis, the paper also provides the simulation results, which further validate the proposed scheme.
基金Project supported by the National Natural Science Foundation of China (No.10432030).
文摘Assuming the material properties varying with an exponential law both in the thick- ness and radial directions, axisymmetric bending of two-directional functionally graded circular and annular plates is studied using the semi-analytical numerical method in this paper. The deflections and stresses of the plates are presented. Numerical results show the well accuracy and convergence of the method. Compared with the finite element method, the semi-analytical nu- merical method is with great advantage in the computational efficiency. Moreover, study on ax- isymmetric bending of two-directional functionally graded annular plate shows that such plates have better performance than those made of isotropic homogeneous materials or one-directional functionally graded materials. Two-directional functionally graded material is a potential alternative to the one-directional functionally graded material. And the integrated design of materials and structures can really be achieved in two-directional functionally graded materials.
文摘The mooring and riser system is the most critical part of an ofshore oil terminal.Traditionally,these two parts are designed separately without considering the nonlinear interaction between them.Thus,the present paper aims to develop an inte-grated design process for riser systems with a lazy-S confguration and mooring systems in the ofshore catenary anchor leg mooring(CALM)oil terminal.One of the important criteria considered in this integrated design is the ofset diagram and safe operation zone(SAFOP)related to the mooring system and the riser,respectively.These two diagrams are obtained separately by diferent analyses;therefore,codes or standards are available separately for two components.In this methodol-ogy,the diagrams of both risers and mooring lines are incorporated into a single spiral,thus identifying the safe and failure zones of risers and the mooring lines of the oil terminal.This,in turn,leads to substantial benefts in terms of overall system response,cost reduction,and safety to the ofshore oil terminal.To implement this process,three diferent riser lengths with the lazy-S confguration are considered at three diferent sea depths at the terminal installation site.For each condition,the integrated design of the mooring system and riser is executed according to the derived procedure.Then,coupled dynamic models,wherein both buoys and hoses are included,are developed using OrcaFlex.Results show that the criteria of the relevant regulations are not satisfed by reducing the length of the riser relative to the designed size.Further,as water depth increases,this type of riser confguration shows good coupled performance while interacting with the mooring system.In the cross ofset mode,the maximum margin is created between the ofset diagram and the SAFOP diagram,while the most critical dynamic response of the tanker and terminal system occurs in the near and far modes.Therefore,with this method,the best position for the riser direction with the tanker direction is 90°in the best case.