Three-Dimensional Analysis of Rolling by Twin Shear Stress Yield Criterion

Using the twin shear stress yield criterion, the surface integral of the co-line vectors, and the integration depending on upper limit, Kobayashi＇s three-dimensional velocity field of rolling was analyzed and an analytical expression of rolling torque and single force was obtained. Through redoing the same experiment of rolling pure lead as Sims, the calculated results by the above expression were compared with those of Kobayashi and Sims formulae. The results show that the twin shear stress yield criterion is available for rolling analysis and the calculated results by the new formula are a little higher than those by Kobayashi and Sims ones if the reduction ratio is less than 30%.

An Application of the Modified Shear Lag Model to Study the Influence of Thermal Residual Stresses on the Stiffness and Yield Strength of Short Fiber Reinforced Metal Matrix Composites

The modified shear lag model proposed recently was applied to calculate thermal residual stresses and subsequent stress distributions under tensile and compressive loadings. The expressions for the elastic moduli and the yield strengths under tensile and compressive loadings were derived which take account of thermal residual stresses. The asymmetries in the elastic modulus and the yield strength were interpreted using the derived expressions and the obtained results of the stress calculations. The model predictions have exhibited good agreements with the experimental results and also with the other theoretical predictions

Rheological properties and concentration evolution of thickened tailings under the coupling effect of compression and shear

Cemented paste backfill(CPB)is a key technology for green mining in metal mines,in which tailings thickening comprises the primary link of CPB technology.However,difficult flocculation and substandard concentrations of thickened tailings often occur.The rheological properties and concentration evolution in the thickened tailings remain unclear.Moreover,traditional indoor thickening experiments have yet to quantitatively characterize their rheological properties.An experiment of flocculation condition optimization based on the Box-Behnken design(BBD)was performed in the study,and the two response values were investigated:concentration and the mean weighted chord length(MWCL)of flocs.Thus,optimal flocculation conditions were obtained.In addition,the rheological properties and concentration evolution of different flocculant dosages and ultrafine tailing contents under shear,compression,and compression-shear coupling experimental conditions were tested and compared.The results show that the shear yield stress under compression and compression-shear coupling increases with the growth of compressive yield stress,while the shear yield stress increases slightly under shear.The order of shear yield stress from low to high under different thickening conditions is shear,compression,and compression-shear coupling.Under compression and compression-shear coupling,the concentration first rapidly increases with the growth of compressive yield stress and then slowly increases,while concentration increases slightly under shear.The order of concentration from low to high under different thickening conditions is shear,compression,and compression-shear coupling.Finally,the evolution mechanism of the flocs and drainage channels during the thickening of the thickened tailings under different experimental conditions was revealed.

A New Modified Conductivity Model for Prediction of Shear Yield Stress of Electrorheological Fluids Based on Face-center Square Structure

A new modified conductivity model was established to predict the shear yield stress of electrorheological fluids (ERF). By using a cell equivalent method, the present model can deal with the face-center square structure of ERF. Combining the scheme of the classical conductivity model for the single-chain structure, a new formula for the prediction of the shear yield stress of ERF was set up. The influences of the separation distance of the particles, the volume fraction of the particles and the applied electric field on the shear yield stress were investigated.

Effects of PVA and PEG on pH Dependent Shear Yield Stress of Concentrated Alumina Suspensions

The pH dependence of the extrapolated shear yield stress for Alcoa A16 a-Al2O3 suspensions at the powder volume fraction of 0.27 with and without addition of both polyvinyl alcohol (PVA) and polyethylene glycol (PEG) each at fixed 0.18% of the powder mass was studied. With the polymer added, the full deflocculation of the suspension shifts from about pH=4 to around pH=1.5, at which the minimum value of shear yield stress is higher than that at pH=4. The addition of both PVA and PEG was found to prevent the filter cake from cracking.

Correlation Between Yield Stress of Silty Mud Sediments and Continuous Oscillatory Shearing Properties

Analyzing the rheological properties of silty beds subjected to continuous oscillatory shear loading is crucial for understanding the morphological deformation of the seabed and ensuring safety in geological and marine engineering applications.In this study,the effects of oscillatory shearing properties on the yield stress(S_(u))of silty sediments were quantitatively investigated.The effects of oscillatory shear strength(0-3),water content(26.6%-70.84%),and particle diameter(8.79-50μm)were examined extensively through a series of laboratory tests.The results indicated that the three aforementioned parameters were the major factors that affected the rheological characteristics of silty sediments.Furthermore,their effects could be elucidated using the yield stress of cohesive sediments as the indicator parameter.The ratio of yield stress(S_(u)/S_(u0))varied as the oscillatory shear strength increased up to a critical value,Λ_(cr).S_(u)bsequently,the ratio remained at a constant value.It was deduced that the yield stress decreased with increasing oscillatory shear strength forΛ<Λ_(cr),when the sediments were in a non-equilibrium fluidization stage.WhenΛ>Λ_(cr),the sediments entered an equilibrium fluidization stage,and the yield stress remained almost constant,irrespective of the oscillatory shear strength.Furthermore,during the equilibrium fluidization stage,it was observed that the ratio S_(u)/S_(u0)did not vary with water content but decreased as the particle diameter increased.Finally,based on regression analysis of the experimental data for non-equilibrium and equilibrium fluidization stages,a correlation between yield stress of silty sediments and continuous oscillatory shearing properties was proposed.This correlation can aid in understanding the changes in solid resistance and assessing safety in piling engineering.Furthermore,it can provide a theoretical guidance for reducing soil resistance in marine structures using mechanical vibrations.

A New Modification to Shear Lag Model as Applied to Stiffness and Yield Strength of Short Fiber Reinforced Metal Matrix Composites

A new modification for the shear lag model is given and the expressions for the stiffness and yield Strength of short fiber metal matri×composite are derived. These expressions are then compared with our experimental data in a SiCw/Al-Li T6 composite and the published experimental data on different SiCw/Al T6 composites and also compared with the previous shear lag models and the other theoretical models.

Deformation behaviour and microstructure evolution of AlMg6Mn alloy during shear spinning

Deformation behavior and microstructure of AlMg6Mn alloy subjected to shear spinning were studied by means of mechanical characterization, optical and SEM＋EDS microscopy. Specimens were shear spun on an industrial spinning machine using different mandrels, providing reductions of wall thickness of 30%, 50% and 68%. The grain structure developed during shear spinning refines gradually. The grains elongate in axial direction with increase of reduction, and also stretches along circumferencial direction. Optimal combination of strength and elongation is observed. This is attributed to grain refinement and dislocation reactions with particles and atoms of Mg and Mn in solid solution.

Effect of fiber angle on LYP steel shear walls behavior

Steel shear wall(SSW) was properly determined using numerical and experimental approaches.The properties of SSW and LYP(low yield point) steel shear wall(LSSW) were measured.It is revealed that LSSW exhibits higher properties compared to SSW in both elastic and inelastic zones.It is also concluded that the addition of CFRP(carbon fiber reinforced polymers) enhances the seismic parameters of LSSW(stiffness,energy absorption,shear capacity,over strength values).Also,stress values applied to boundary frames are lower due to post buckling forces.The effect of fiber angle was also studied and presented as a mathematical equation.

pH Value Effects in Shear Rheology of Concentrated Alumina Suspensions

The influence of pH on the rheological properties of concentrated alumina suspensions was investigated. At various pH values, the alumina exhibited pseudoplastic, near Bingham flow behaviors. The fully-deflocculated suspensions exhibited Newtonian flow behaviors, while the fully-flocculated suspensions demonstrated very high viscosity and shear yield stress.

Analysis of complete plasticity assumption for solid circular shaft under pure torsion and calculation of shear stress

The distribution of shear stress on the cross-section of plastic metal solid circular shaft under pure torsion yielding, the applicability of complete plastic model assumption and the shear stress formula were researched. Based on the shear stress formula of circular shaft under pure torsion in elastic stage, the formula of torque in elastic stage and the definition of yield, it is obtained that the yielding stage of plastic metal shaft under pure torsion is only a surface phenomenon of torque-torsion angle relationship, and the distribution of shear stress is essentially different from that of tensile stress when yielding under uniaxial tension. The pure torsion platform-torsion angle and the shape of torque-torsion angle curve cannot change the distribution of shear stress on the shaft cross-section. The distribution of shear stress is still linear with the maximum shear stress ts. The complete plasticity model assumption is not in accordance with the actual situation of shaft under torsion. The experimental strength data of nine plastic metals are consistent with the calculated results of the new limiting strain energy strength theory （LSEST）. The traditional yield stress formula for plastic shaft under torsion is reasonable. The shear stress formula based on the plane assumption in material mechanics is applicable for all loaded stages of torsion shaft.

Static Yield Stress of Cement-based Grouting Material under Different Rheological Modes

To quantitatively estimate the workability of cement-based grouting material,from the perspective of rheology,the result of the static yield stress evaluated using the rate-controlled and stress-controlled modes,respectively,was compared using the Rheowin rheometer.Also,the correlation of workability and solid concentration of slurry with static yield stress was studied.Results show that the static yield stress of cement-based grouting slurry relates to the established slurry structure,and is the shear stress corresponding to the transformation of elastics to plastics;In rate-controlled mode,the static yield stress of the slurry is related to the shear rate.The higher the shear rate,the greater the yield stress of the slurry.For the stress-controlled mode,the result is more accurate and suitable for testing static yield stress under different water-cement ratios.Since the water-cement ratio has a good correspondence with the static yield stress and the static yield stress has a good correspondence with the slump flow of the slurry,the static yield stress is the minimum stress to be overcome when the slurry begins to flow and it reflects the yield behavior and structural stability of the cement.

A study of the energy yield criterion of geomaterials

The study results of the internal friction character of geomaterials conclude that the internal friction exists in mechanical elements all the time having a direction opposite to the shear stress,and the deformation failure mechanism of geomaterials greatly differs from that of metals. For metals,the failure results from shear stresses make the crystal structure slip; whereas for geomaterials,owing to its attribute of granular structures,their deformation follows the friction law,it is the co-action of shear stresses and perpendicular stresses that makes grains overcome the frictions between them,thus leading to the final failure of relative sliding.Therefore,on the basis of the cognition above,a triple shear energy criterion is proposed. Its corresponding Drucker-Prager criterion for geomaterials is also given. The new criterion can be rewritten to the Mohr-Coulomb criterion by neglecting the effect of the intermediate principal stress,and to the Mises criterion by not taking the internal friction angle into consideration. Then the studies of yield criteria commonly used are conducted systematically from the points of stress,strain and energy of geomaterials. The results show that no matter which expression form of stress,strain or energy is used for the yield criterion,the essence is the same and the triple shear energy yield criterion is the unified criterion of materials. Finally,the experimental verification is conducted in connection with the practical application of the triple shear energy yield criterion in an engineering project,and the calculation result shows that the Mohr-Coulomb criterion which only takes the single shear surface into account is more conservative than the energy criterion that does consider the effect of triple shear surfaces.

nvestigation of Structural Steel Webs for Punching Shear

Shear tab connections or simple connections are widely used in structural steel structures. There are several limit states associated with these connections such bolt shear, bolt bearing, block shear, shear yielding and shear rupture. A modified version of the shear tab has been developed during the last decade, which is extended shear tab connections. In developing design provisions for the extended shear tab connections, experimental work showed that there are additional limit states other than those mentioned above that limit the capacity of the extended shear connection. Extended shear tab connections could be used to frame beam-to-column or beam-to-girder. In the case where a beam is framed into girder, a new limit state develops in the web of the supporting girder. This limit state is punching shear of the supporting girder web which is due to a higher moment. The higher moment in extended shear tab connections is due to the larger moment arm （eccentricity） from the bolt line, the location of the shear force, to the support, which is in this case the girder＇s web. This study investigates the supporting girder web using experimental work, finite element analysis, and yield line theory. This paper shows the result of this investigation and proposes an evaluation of the web capacity equation which should be used when calculating the beam-to-girder connection capacity.

A Linearized and Unified Yield Criterion of Metals and Its Application

In this paper a linearized and unified yield crierion of metals is presented, which is in a form of a set of linear functions with two pararneters. The parameters are ex- pressed in terms of tension yield stress and so-called “shear-stretch ratio” and can bereadily determined from experimental data. It is shown that in stress space the set of yield functions is a set of polygons with twelve edges located between the Tresca’s hexagon and twin-shear-stress hexagon￣[1]. In this paper the present yield function isused to analyse the prestressiap loose running fit cylinders.

Wind Shear Investigation for Site-Specific Wind Turbine Performance Assessment

The wind energy assessment studies are generally performed referring to neutral stability conditions for the atmosphere; this is considered a good hypothesis because neutral conditions characterize the high wind situations. However the increasing size of modem multi megawatt wind turbines allows to produce energy even in low wind regimes and non-neutral conditions can involve significant production period. In such situations the variations of the vertical wind shear can affect the energy production in a sensible way and it could be fundamental to investigate how atmospheric stability and orography can affect the wind profile and the power conversion. In this paper meso-scale numerical data, CFD modeling and remote sensed wind data were used in order to analyze such behavior and to understand how wind shear influences the energy content and the discussion about how to adjust the power curve to the site specific conditions.

盾构壁后注浆窜浆模型试验及发生条件研究

全断面围岩管片壁后注浆因向开挖面方向的窜浆现象会引起盾尾空隙注浆不饱满,管片上浮、错台及开裂,螺机喷涌等事故常有发生,已经引起广泛重视。通过设计自制壁后注浆液窜浆模型装置进行试验,分析浆液性质、缝隙厚度、注浆压力差对是否发生窜浆及窜浆量的影响,并探讨了不发生窜浆的临界条件。结果表明:(1)浆液压力与窜浆距离呈线性衰减,当浆液稠度较低时,窜浆量与缝隙厚度、浆液稠度呈近似线性正相关、与浆液的剪切屈服应力呈近似线性负相关,窜浆距离与注浆压力差呈近似线性正相关;当浆液稠度增大时,以上关系将逐渐转化为非线性关系;(2)通过极差分析表明浆液的窜浆量受盾壳与岩层间缝隙厚度影响最大,注浆压力与开挖面压力差影响其次,最后是浆液本身的性质;(3)建立了窜浆临界分析模型和计算公式,得到了窜浆发生条件和判别方法,可用于指导稳定围岩地层中盾构掘进时浆液的配制。

联肢弯剪型钢板剪力墙抗震性能试验研究

联肢钢板剪力墙结构是将2片钢板剪力墙通过钢连梁连接形成的抗侧力结构。通过对1榀1/3缩尺的4层联肢弯剪型钢板剪力墙试件进行低周往复加载试验,从滞回曲线、骨架曲线、延性、承载力及刚度退化、耗能能力等方面研究了该结构体系的抗震性能,并且对试件的屈服顺序和变形模式进行了分析。结果表明:联肢钢板剪力墙试件的延性系数达到5.03,承载力退化系数均大于0.96,承载力和刚度退化稳定,等效黏滞阻尼系数达到0.25以上,表明联肢弯剪型钢板剪力墙具有优越的抗震性能。加载过程中,连梁先于墙板发生屈服,墙板先屈曲后屈服,此后柱脚和横梁相继屈服。连梁的引入改变了结构的屈服机制,提高了整体的延性和耗能能力,能够组成多道抗震防线,且试件整体最终也体现出合理的破坏机制。整体侧移曲线呈弯剪变形模式。该试验研究更加贴合实际工程中联肢钢板剪力墙结构的应用情况,为联肢钢板剪力墙结构的进一步研究和应用提供了试验基础。

流变学参数表征湿喷混凝土工作性研究进展

为提高工作性对湿喷混凝土施工性能(可输送性、可喷性)的指导作用,归纳了现有各种技术规范的工作性要求,回顾了流变特性与可喷性相关性研究进展,探讨了流变性能时变机制,总结了时变模型发展现状。结果表明,坍落度无法协调可输送性与可喷性工作性需求矛盾,流变学参数应用效果优于坍落度;屈服剪切应力增加,一次喷射厚度变大,回弹率减小;塑性黏度降低,管道输送压力减小,可输送性变好,但屈服剪切应力、塑性黏度与密实度的相关性尚需深入研究;主流的流变性能时变模型为指数、对数、线性、幂函数等经验公式,应加强有物理意义的模型推导;时变预测模型缺乏有效验证手段,应重点研发速凝体系下湿喷混凝土流变性能的原位评估方法。

城市轨道交通装配式地下车站新型构件连接方案的抗剪及抗震性能分析

[目的]为了进一步推广地下装配式结构在城市轨道交通工程中的应用,应对城市轨道交通车站明挖装配式出入口施工的关键技术(尤其是新型构件连接方案)进行研究。[方法]设计了由2块尺寸相同的不等边C形标准构件(有2道横向裂缝)拼接而成的城市轨道交通车站装配式出入口结构,基于此结构提出了一种新型的构件连接方案。通过模型试验及数值模拟,研究了该新型连接节点的抗剪性能和抗震性能,得出了不同受力条件下的荷载-位移曲线、抗剪形态、抗震耗能及延性等指标,验证了该新型连接节点的可靠性。[结果及结论]装配构件的截面抗剪承载力远高于传统现浇截面抗剪承载力;型钢的存在可以充分保证试件的抗剪能力;“承插接口+型钢插板”是一种可靠的连接方式,其各项性能与现浇试件相比大致相当;型钢插入长度的变化对接缝处裂缝及其最大承载力的影响很小,建议选用的型钢插入长度等与构件厚度一致。